BSA C15

Last updated

BSA C15
BSA C15 250cc 1960 - Flickr - mick - Lumix(1).jpg
ManufacturerBSA Motorcycles Ltd., Armoury Road, Small Heath, Birmingham, England
Also calledStar
Parent company Birmingham Small Arms Company
Production19581967
Predecessor BSA C12
SuccessorBSA B25 Starfire, BSA C25 Barracuda
Engine 4-stroke 249 cc (15.2 cu in) OHV single cylinder, alloy head, Amal 375 carburettor [1]
Bore / stroke 67 x 70 mm
Power 15 bhp (11 kW) @7000rpm [1]
Ignition type Coil with 60 watt Lucas RM13 alternator
Transmission Four-speed, chain drive
Brakes 6 inches (15 cm) front and rear with full width hubs
Tyres 3.25 x 17" front and rear [1]
Wheelbase 51.25 inches (130.2 cm)
Fuel capacity3 gallons

The BSA C15 was a 250 cc single-cylinder ohv motorcycle manufactured by the British company BSA from September 1958 until 1967, and was BSA's first four-stroke unit-construction bike. [2] For most of that period, after the introduction of 'Learner Laws' in 1961, a 250 cc was the largest capacity solo machine that a learner could ride unaccompanied when displaying L-plates in the United Kingdom. A road-going Sports derivative was added in 1961, and off-road versions, for Trials and Scrambles, were also available in the range. [2]

Contents

Producing only 15 bhp (11 kW), the C15's lack of power meant that it was hard for the BSA to compete with the more sophisticated Japanese motorcycles (such as the Honda C71 and CB72) which began arriving in the UK in the 1960s. [3]

Development

BSA acquired the Triumph marque in 1951, and the BSA C15 250 cc four stroke was derived from the 200 cc Triumph Tiger Cub, itself coming from the 150cc Terrier. Edward Turner became head of the BSA automotive division and in 1958 BSA introduced the concept of unit construction, where the engine and gearbox were combined in one piece rather than as separate components. The BSA C15 'Star' was the first unit construction model and proved more reliable and economical than its predecessor, the pre-unit BSA C11. [3]

The C11 engine had an iron barrel and alloy head with overhead valves operated by pushrods which ran in a separate tube to fully enclosed rockers. The camshaft was geared directly from the crankshaft with skew gears driving the oil pump and the contact breaker assembly mounted behind the cylinder via a shaft. The alternator was to the left and the primary drive was via a duplex chain to a multi plate clutch. The four speed gearbox was at the rear of the vertically split crankcase. The frame was single loop with twin rails under the engine and pivoted fork rear suspension, and both wheels were 17 inch with full width cast iron hubs. An oil tank was under the seat on the right matched by a toolbox on the left. Between them was an ignition switch panel hiding the battery. The headlamp was fitted in a nacelle which also housed the instruments and switches as was fashionable at the time. Deeply valanced mudguards were fitted to the standard model, making it look heavier than it actually was. [4]

A successor to the C11, the C15 had a completely redesigned frame and 250 cc engine. The bike proved to need careful maintenance, being prone to oil leaks, electrical faults, gearbox problems, valve-gear failures, a weak big-end, and clutch adjustment problems. [3] Initially, the contact breaker housing protruded at the rear of the cylinder above the gearbox, but was later relocated to the right-side crankcase, accessed via a circular plate. [2]

BSA Starfire Flickr - ronsaunders47 - BSA C15. 250 cc STARFIRE..jpg
BSA Starfire

BSA developed an increased capacity 441 cc model, marketed as the BSA B44 Shooting Star and the BSA Victor Special. [3] Following development work in producing Jeff Smith's works B40-based Victor, from 1966 onwards the C15 bottom-end (crankcases, bearings, oil pump with circulation system and gearbox components) was similarly upgraded. [5]

In 1967 the 250 cc C15 was succeeded by the BSA B25 'Starfire' and BSA C25 'Barracuda' models, which had a quickly detachable rear wheel and 12 volt electrics.

Models

BSA C15 Star

The 1959 C15 Star was the first model in the range.

BSA C15 'Sportsman' (SS80)

In 1961 the 'Super Sports' model (SS80) or C15 Sportsman joined the range, with a tuned engine, roller big-ends and lower handlebars. A faster 350 cc version, the SS90 based on the BSA B40 was also added to the range but was not a big seller to the general public – as it was too big for learners and too small for those who had passed their motorcycle test - but the B40 was ideal for military use including use with the British Armed Forces. [3]

BSA C15G

The BSA C15G was produced from 1966 to 1967 and was the last version of the C15 engine with the ball bearing timing side main bearing, roller drive side and strengthened crankcases, larger oil pump and needle roller gearbox layshaft bearings.

BSA C15T

Trials C15 BSA C15T Trials 1961.jpg
Trials C15

The BSA C15T was a trials version with a higher clearance frame fitted with a reinforced plate, special gear ratios suited to off-road use, a 20" front wheel in the UK and a high level exhaust pipe. A special tank and optional lighting allowed it to be converted for legal road use. [3] Still with an iron barrel and alloy head, the engine had a special camshaft to lower the tune for off-road trials use (for more "plonk"). The first series competition frame with single down tube suffered rear tyre clearance problems in heavy mud. This was largely resolved in the later twin down-tube competition frame with its wider swing arm. The C15T proved to be competitive at club and national levels, and it remained unchanged in the BSA range until 1965. [6]

BSA C15T Trials Cat

In 1964 and 1965 the overbored 500 cc BSA C15T 'Trials Cat' ridden by Jeff Smith won the 500 cc World Moto-Cross Championship. This success led to the development of the 441 cc BSA Victor Scrambler.

BSA C15S

The BSA C15S was the scrambler (motocross) competition version of the 250 cc Star produced between 1959 and 1965. As with the trials model, the C15S saved the weight of a battery through an 'energy transfer' electrical system which was notoriously unreliable. [3] The problem was that the timing and points gap required far too much careful setting for a rugged competition motorcycle. The scrambler C15 shared the same frame as the trials (designated with a C suffix), had a larger exhaust valve, higher compression ratio and modified camshaft for more power. It was unsilenced and had special tyres and strengthened fork springs with rubber fork gaiters to protect the seals. [4]

BSA C15 Starfire

The BSA C15 Starfire Roadster was produced between 1963 and 1964 with chrome mudguards and tank side panels. Re shaped seat and tank, which gave the bike a more modern appearance.

BSA C15P

The BSA C15P was a police model produced between 1963 and 1967.

See also

Related Research Articles

Yamaha XS 650 Yamaha motorcycle

The Yamaha XS650 is a mid-size motorcycle made by Yamaha Motor Company. The standard model was introduced in October 1969,and produced through 1979. The "Special" cruiser model was introduced in 1978 and produced through 1985. The XS650 began with the 1955 Hosk SOHC 500 twin. After about 10 years of producing 500 twin, Hosk engineers designed a 650 cc twin. Later the Hosk company was acquired by Showa Corporation, and in 1960 Yamaha had bought Showa with Hosk's early design of 650 cc twin.

BSA Rocket 3/Triumph Trident 1960s/1970s British motorcycle made by Triumph Engineering, Meriden

The Triumph Trident and BSA Rocket 3 was a technically advanced, high-performance roadster motorcycle made by Triumph Engineering and BSA from 1968 to 1975, and sold under both the Triumph and BSA marques. Alongside the Honda CB750, and later the Kawasaki triples, it brought a new level of sophistication to street motorcycles, marking the beginning of the superbike era. The Honda CB750 overshadowed the Trident to be remembered as the 'first superbike', in spite of the Triumph Trident actually debuting before the Honda by a few weeks.

Triumph Bonneville

The Triumph Bonneville is a standard motorcycle featuring a parallel-twin four-stroke engine and manufactured in three generations over three separate production runs.

Cotton (motorcycle) former British motorcycle manufacturer

The Cotton Motor Company, was a British motorcycle manufacturer of 11a Bristol Road, Gloucester, and was founded by Frank Willoughby Cotton in 1918. F.W. presided over the company until his retirement in 1953. The company was reconstituted as E. Cotton (Motorcycles) Ltd, and traded until 1980. The marque was later resurrected in the late 1990s by a business which manufactured replicas of earlier machines.

Unit construction

Unit construction is the design of larger motorcycles where the engine and gearbox components share a single casing. This sometimes includes the design of automobile engines and was often loosely applied to motorcycles with rather different internal layouts such as the flat twin BMW models.

Ducati L-twin engine

The next new Ducati engine to appear after the Ducati Apollo was the 90° V-twin, initial Grand Prix racing versions being 500 cc, and the production bikes were 750 cc. There was also the Ducati 750 Imola Desmo that won at Imola in 1972. These engines had bevel gear shaft drive to the overhead camshaft, and were produced in round, square, and Mille crankcases. In the 1980s, these gave way to the belt drive camshaft engines that have continued to this day, in air-cooled and liquid-cooled form. The Mille used a plain bearing crank, like the belt models.

BSA Gold Star Motorcycle made by BSA from 1938 to 1963.

The BSA Gold Star is a motorcycle made by BSA from 1938 to 1963. They were 350 cc and 500 cc single-cylinder four-stroke production motorcycles known for being among the fastest bikes of the 1950s. Being hand built and with many optional performance modifications available, each motorcycle came from the factory with documented dynamometer test results, allowing the new owner to see the horsepower (bhp) produced.

Norton Commando British motorcycle produced from 1967 to 1977

The Norton Commando is a British Norton-Villiers motorcycle with an OHV pre-unit parallel-twin engine, produced by the Norton Motorcycle company from 1967 until 1977. Initially having a nominal 750 cc displacement, actually 745 cc (45.5 cu in), in 1973 it became an 850 cc, actually 828 cc (50.5 cu in). It had a hemi-type head, similar to all OHV Norton engines since the early 1920s.

Edward Turner (motorcycle designer)

Edward Turner was an English motorcycle designer. He was born in Camberwell in the London Borough of Southwark, on the day King Edward VII was proclaimed King. In 1915, Turner had his first ride on a motorcycle, a Light Tourist New Imperial.

Francis-Barnett Defunct motorcycle manufacturer

Francis & Barnett Limited was an English motorcycle manufacturer founded in 1919 by Gordon Inglesby Francis and Arthur Barnett and based in Lower Ford Street, Coventry, England. Early motor cycles were affectionately known as ' Franny B'. Motorcycles were produced for enthusiasts and was reasonably affordable for citizens for use as general transport. The majority of the lighter motorcycles used Villiers and later Two-stroke engine and later Associated Motor Cycles AMC engines. During the 1930s the 250cc Cruiser model 250 cc (15 cu in) was developed with a faired engine that protected those riding from any oil or dirt – one of the first of its kind to do so. AMC took over Francis & Barnett Limited in 1947 combining this with the James motorcycle models in 1957. The combined company remained in business until 1966.

Triumph Tiger Cub British motorcycle

The Triumph Tiger Cub was a 200 cc (12 cu in) single-cylinder British motorcycle made by Triumph Motorcycles at their Meriden factory. Based on the Triumph T15 Terrier 150 cc, itself a surprise announcement just before the 1952 show, the 200 cc T20 Tiger Cub designed by Edward Turner and launched at the Earls Court show in November 1953 competed well against the other small-capacity motorcycles of the time, such as those using Villiers two-stroke engines.

BSA M20 British motorcycle

The BSA M20 was a British motorcycle made by Birmingham Small Arms Company (BSA) at their factory in Small Heath, Birmingham. Although initially viewed as a near failure by the War Office in 1936, the M20 evolved into one of the longest serving motorcycles in the history of British military motorcycling, as well as becoming the most numerous type produced for World War II with 126,000 in active service. Many are still in use around the world today.

BSA A7

The BSA A7 was a 500cc motorcycle model range made by Birmingham Small Arms Company (BSA) at their factory in Armoury Road, Small Heath, Birmingham. The range was launched in 1946 using a 495 cc (30.2 cu in) long stroke engine. An improved 497 cc (30.3 cu in) version based on the BSA A10 engine was launched in 1950. The various A7 models continued in production with minor modifications until 1961/2 when they were superseded by the unit-construction A50 model.

BSA motorcycles

BSA motorcycles were made by the Birmingham Small Arms Company Limited (BSA), which was a major British industrial combine, a group of businesses manufacturing military and sporting firearms; bicycles; motorcycles; cars; buses and bodies; steel; iron castings; hand, power, and machine tools; coal cleaning and handling plants; sintered metals; and hard chrome process.

Honda C92, CB92, C95 Benly Parallel-twin motorcycle

The Honda C92 Benly is a 125 cc (7.6 cu in) parallel-twin motorcycle made by Honda from 1959 through 1965. Running concurrently were the CB92 Sports and the slightly larger C95 150 cc (9.2 cu in), called the CA92 and CA95 in the US. These twins took their styling and design cues from the larger-displacement Honda C71, C76, C72, C77 Dream series.

BSA A10 series

The BSA A10 series was a range of 646 cc (39.4 cu in) air-cooled parallel twin motorcycles designed by Bert Hopwood and produced by Birmingham Small Arms Company at Small Heath, Birmingham from 1950 to 1963. The series was succeeded by the A65 unit construction models.

BSA B25 Series of motorcycles made by the Birmingham Small Arms Company

The BSA B25 was a series of 250 cc (15 cu in) unit construction single-cylinder OHV four-stroke motorcycles made by the Birmingham Small Arms Company. Developed from the BSA C15, the machines were produced between 1967 and 1971. The B25 was the fastest British production 250.

BSA B40

The BSA B40 was a series of 350 cc (21 cu in) unit construction single-cylinder OHV four-stroke motorcycles made by the Birmingham Small Arms Company. Developed from the BSA C15, the machines were produced between 1961 and 1967 for civilian use. Military versions were manufactured from 1967 to 1970. Around 14,000 machines were built in total.

The Ducati 450 Mark 3 is a 436 cc (26.6 cu in) single cylinder bevel drive SOHC motorcycle produced by the Italian manufacturer Ducati from 1969 to 1974. The 450 was largest displacement version of the OHC single series produced by Ducati and used the 'wide case' engine. A higher performance version, the Ducati 450 Mark 3D, which used desmodromic valves was also available. The 450 was criticised for vibration and lack of performance compared to other models such as the Mach 1.

Ducati 250 Mark 3 SOHC motorcycle by Ducati

The Ducati 250 Mark 3 is a 249 cc (15.2 cu in) single cylinder bevel drive SOHC motorcycle produced by the Italian manufacturer Ducati from 1967 to 1974. Initially produced using the 'narrow case' engine, the newly introduced 'wide case' engine was used from 1968. A higher performance version, the Ducati 250 Mark 3D, which used desmodromic valves was also available.

References

  1. 1 2 3 Motor Cycle Data Book 1960, p.60 George Newnes Ltd., London. Accessed and added 2014-10-21
  2. 1 2 3 Motor Cycle, 22 April 1965, pp.508-511 C15 Riders Report collated by Mike Evans. Accessed 2014-10-18
  3. 1 2 3 4 5 6 7 Kemp, Andrew; De Cet (2004). Classic British Bikes. Mirco. Bookmart Ltd. ISBN   1-86147-136-X.
  4. 1 2 Bacon, Roy (1988). British Motorcycles of the 60's. Osprey Publishing. ISBN   1-85648-166-2.
  5. Motor Cycle, 29 July 1966, pp.112-113 Sturdier BSA two-fifties. Accessed 2014-10-18
  6. "BSA C15T" . Retrieved 26 October 2009.