Bypass ratio

Schematic turbofan engines. The high-bypass engine (top) has a large fan that routes much air around the turbine; the low-bypass engine (middle) has a smaller fan routing more air into the turbine; the turbojet (bottom) has zero bypass, and all air goes through the turbine.

The bypass ratio (BPR) of a turbofan engine is the ratio between the mass flow rate of the bypass stream to the mass flow rate entering the core. ^[1] A 10:1 bypass ratio, for example, means that 10 kg of air passes through the bypass duct for every 1 kg of air passing through the core.

Turbofan engines are usually described in terms of BPR, which together with engine pressure ratio, turbine inlet temperature and fan pressure ratio are important design parameters. In addition, BPR is quoted for turboprop and unducted fan installations because their high propulsive efficiency gives them the overall efficiency characteristics of very high bypass turbofans. This allows them to be shown together with turbofans on plots which show trends of reducing specific fuel consumption (SFC) with increasing BPR. BPR is also quoted for lift fan installations where the fan airflow is remote from the engine and doesn't physically touch the engine core.

Bypass provides a lower fuel consumption for the same thrust, measured as thrust specific fuel consumption (grams/second fuel per unit of thrust in kN using SI units). Lower fuel consumption that comes with high bypass ratios applies to turboprops, using a propeller rather than a ducted fan. ^{[2] [3] [4] [5]} High bypass designs are the dominant type for commercial passenger aircraft and both civilian and military jet transports.

Business jets use medium BPR engines. ^[6]

Combat aircraft use engines with low bypass ratios to compromise between fuel economy and the requirements of combat: high power-to-weight ratios, supersonic performance, and the ability to use afterburners.

Principles

If all the gas power from a gas turbine is converted to kinetic energy in a propelling nozzle, the aircraft is best suited to high supersonic speeds. If it is all transferred to a separate big mass of air with low kinetic energy, the aircraft is best suited to zero speed (hovering). For speeds in between, the gas power is shared between a separate airstream and the gas turbine's own nozzle flow in a proportion which gives the aircraft performance required. The first jet aircraft were subsonic and the poor suitability of the propelling nozzle for these speeds due to high fuel consumption was understood, and bypass proposed, as early as 1936 (U.K. Patent 471,368). The underlying principle behind bypass is trading exhaust velocity for extra mass flow which still gives the required thrust but uses less fuel. Frank Whittle called it "gearing down the flow". ^[7] Power is transferred from the gas generator to an extra mass of air, i.e. a bigger diameter propelling jet, moving more slowly. The bypass spreads the available mechanical power across more air to reduce the velocity of the jet. ^[8] The trade-off between mass flow and velocity is also seen with propellers and helicopter rotors by comparing disc loading and power loading. ^[9] For example, the same helicopter weight can be supported by a high power engine and small diameter rotor or, for less fuel, a lower power engine and bigger rotor with lower velocity through the rotor.

Bypass usually refers to transferring gas power from a gas turbine to a bypass stream of air to reduce fuel consumption and jet noise. Alternatively, there may be a requirement for an afterburning engine where the sole requirement for bypass is to provide cooling air. This sets the lower limit for BPR and these engines have been called "leaky" or continuous bleed turbojets ^[10] (General Electric YJ-101 BPR 0.25) and low BPR turbojets ^[11] (Pratt & Whitney PW1120). Low BPR (0.2) has also been used to provide surge margin as well as afterburner cooling for the Pratt & Whitney J58. ^[12]

Description

Propulsive efficiency comparison for various gas turbine engine configurations

In a zero-bypass (turbojet) engine the high temperature and high pressure exhaust gas is accelerated by expansion through a propelling nozzle and produces all the thrust. The compressor absorbs all the mechanical power produced by the turbine. In a bypass design extra turbines drive a ducted fan that accelerates air rearward from the front of the engine. In a high-bypass design, the ducted fan and nozzle produce most of the thrust. Turbofans are closely related to turboprops in principle because both transfer some of the gas turbine's gas power, using extra machinery, to a bypass stream leaving less for the hot nozzle to convert to kinetic energy. Turbofans represent an intermediate stage between turbojets, which derive all their thrust from exhaust gases, and turbo-props which derive minimal thrust from exhaust gases (typically 10% or less). ^[13] Extracting shaft power and transferring it to a bypass stream introduces extra losses which are more than made up by the improved propulsive efficiency. The turboprop at its best flight speed gives significant fuel savings over a turbojet even though an extra turbine, a gearbox and a propeller were added to the turbojet's low-loss propelling nozzle. ^[14] The turbofan has additional losses from its extra turbines, fan, bypass duct and extra propelling nozzle compared to the turbojet's single nozzle.

To see the influence of increasing BPR alone on overall efficiency in the aircraft, i.e. SFC, a common gas generator has to be used, i.e. no change in Brayton cycle parameters or component efficiencies. Bennett ^[15] shows in this case a relatively slow rise in losses transferring power to the bypass at the same time as a fast drop in exhaust losses with a significant improvement in SFC. In reality increases in BPR over time come along with rises in gas generator efficiency masking, to some extent, the influence of BPR.

Only the limitations of weight and materials (e.g., the strengths and melting points of materials in the turbine) reduce the efficiency at which a turbofan gas turbine converts this thermal energy into mechanical energy, for while the exhaust gases may still have available energy to be extracted, each additional stator and turbine disk retrieves progressively less mechanical energy per unit of weight, and increasing the compression ratio of the system by adding to the compressor stage to increase overall system efficiency increases temperatures at the turbine face. Nevertheless, high-bypass engines have a high propulsive efficiency because even slightly increasing the velocity of a very large volume and consequently mass of air produces a very large change in momentum and thrust: thrust is the engine's mass flow (the amount of air flowing through the engine) multiplied by the difference between the inlet and exhaust velocities in—a linear relationship—but the kinetic energy of the exhaust is the mass flow multiplied by one-half the square of the difference in velocities. ^{[16] [17]} A low disc loading (thrust per disc area) increases the aircraft's energy efficiency, and this reduces the fuel use. ^{[18] [19] [20]}

The Rolls–Royce Conway turbofan engine, developed in the early 1950s, was an early example of a bypass engine. The configuration was similar to a 2-spool turbojet but to make it into a bypass engine it was equipped with an oversized low pressure compressor: the flow through the inner portion of the compressor blades went into the core while the outer portion of the blades blew air around the core to provide the rest of the thrust. The bypass ratio for the Conway varied between 0.3 and 0.6 depending on the variant ^[21]

The growth of bypass ratios during the 1960s gave jetliners fuel efficiency that could compete with that of piston-powered planes. Today (2015), most jet engines have some bypass. Modern engines in slower aircraft, such as airliners, have bypass ratios up to 12:1; in higher-speed aircraft, such as fighters, bypass ratios are much lower, around 1.5; and craft designed for speeds up to Mach 2 and somewhat above have bypass ratios below 0.5.

Turboprops have bypass ratios of 50-100, ^{[2] [3] [4]} although the propulsion airflow is less clearly defined for propellers than for fans ^[22] and propeller airflow is slower than the airflow from turbofan nozzles. ^{[20] [23]}

Engine bypass ratios

Turbofan Bypass Ratio Evolution

Turbofan engines ^[24]

Model	First	BPR	Thrust	Major applications
P&W PW1000G [25]	2008	9.0–12.5	67–160 kN	A320neo, A220, E-Jets E2, Irkut MC-21
R-R Trent 1000	2006	10.8–11	265.3–360.4 kN	B787
CFM LEAP [26]	2013	9.0–11.0	100–146 kN	A320neo, B737Max, Comac C919
GE GE90	1992	8.7–9.9	330–510 kN	B777
R-R Trent XWB	2010	9.3	330–430 kN	A350XWB
GE GEnx [27]	2006	8.0–9.3	296-339 kN	B747-8, B787
EA GP7000	2004	8.7	311–363 kN	A380
R-R Trent 900	2004	8.7	340–357 kN	A380
R-R Trent 500	1999	8.5	252 kN	A340-500/600
CFM56	1974	5.0–6.6	97.9-151 kN	A320, A340-200/300, B737, KC-135, DC-8
P&W PW4000	1984	4.8–6.4	222–436 kN	A300/A310, A330, B747, B767, B777, MD-11
GE CF34	1982	5.3–6.3	41–82.3 kN	Challenger 600, CRJ, E-jets
Silvercrest	2012	5.9	50.9 kN	Cit. Hemisphere, Falcon 5X
R-R Trent 800	1993	5.7–5.79	411–425 kN	B777
GE Passport	2013	5.6	78.9–84.2 kN	Global 7000/8000
P&WC PW800	2012	5.5	67.4–69.7 kN	Gulfstream G500/G600
GE CF6	1971	4.3–5.3	222–298 kN	A300/A310, A330, B747, B767, MD-11, DC-10
D-36	1977	5.6	63.75 kN	Yak-42, An-72, An-74
R-R AE 3007	1991	5.0	33.7 kN	ERJ, Citation X
R-R Trent 700	1990	4.9	320 kN	A330
IAE V2500	1987	4.4–4.9	97.9-147 kN	A320, MD-90
P&W PW6000	2000	4.90	100.2 kN	Airbus A318
R-R BR700	1994	4.2–4.5	68.9–102.3 kN	B717, Global Express, Gulfstream V
P&WC PW300	1988	3.8–4.5	23.4–35.6 kN	Cit. Sovereign, G200, F. 7X, F. 2000
GE-H HF120	2009	4.43	7.4 kN	HondaJet
HW HTF7000	1999	4.4	28.9 kN	Challenger 300, G280, Legacy 500
PS-90	1992	4.4	157–171 kN	Il-76, Il-96, Tu-204
PowerJet SaM146	2008	4–4.1	71.6–79.2 kN	Sukhoi Superjet 100
Williams FJ44	1985	3.3–4.1	6.7–15.6 kN	CitationJet, Cit. M2
P&WC PW500	1993	3.90	13.3 kN	Citation Excel, Phenom 300
HW TFE731	1970	2.66–3.9	15.6–22.2 kN	Learjet 70/75, G150, Falcon 900
R-R Tay	1984	3.1–3.2	61.6–68.5 kN	Gulfstream IV, Fokker 70/100
P&WC PW600	2001	1.83–2.80	6.0 kN	Cit. Mustang, Eclipse 500, Phenom 100
Turbojets		0.0		early jet aircraft, Concorde

References

1. "Bypass ratio | engineering".
2. Ilan Kroo and Juan Alonso. "Aircraft Design: Synthesis and Analysis, Propulsion Systems: Basic Concepts Archive" Stanford University School of Engineering, Department of Aeronautics and Astronautics . Quote: "When the bypass ratio is increased to 10-20 for very efficient low speed performance, the weight and wetted area of the fan shroud (inlet) become large, and at some point it makes sense to eliminate it altogether. The fan then becomes a propeller and the engine is called a turboprop. Turboprop engines provide efficient power from low speeds up to as high as M=0.8 with bypass ratios of 50-100."
3. Prof. Z. S. Spakovszky. "11.5 Trends in thermal and propulsive efficiency Archive" MIT turbines , 2002. Thermodynamics and Propulsion
4. Nag, P.K. "Basic And Applied Thermodynamics" p550. Published by Tata McGraw-Hill Education. Quote: "If the cowl is removed from the fan the result is a turboprop engine. Turbofan and turboprop engines differ mainly in their bypass ratio 5 or 6 for turbofans and as high as 100 for turboprop."
5. Animated Engines
6. "Archived copy" (PDF). Archived from the original (PDF) on 2017-05-16. Retrieved 2016-12-25.
7. Gas Turbine Aerodynamics, Sir Frank Whittle, Pergamon Press 1981, p.217
8. Aircraft Engine Design Second Edition, Mattingley, Heiser, Pratt, AIAA Education Series, ISBN   1-56347-538-3, p.539
9. "Archived copy". Archived from the original on 2016-12-24. Retrieved 2016-12-24.
10. Jane's All The World's Aircraft 1975-1976, edited by John W.R. Taylor, Jane's Yearbooks, Paulton House, 8 Sheperdess Walk, London N1 7LW, p.748
11. Zipkin, M. A. (1984). "The PW1120: A High Performance, Low Risk F100 Derivative". Volume 2: Aircraft Engine; Marine; Microturbines and Small Turbomachinery. doi:10.1115/84-GT-230. ISBN   978-0-7918-7947-4.
12. "Never Told Tales of Pratt & Whitney by Dr. Bob Abernethy".
13. "The turbofan engine Archived 2015-04-18 at the Wayback Machine ", page 7. SRM Institute of Science and Technology, Department of aerospace engineering
14. Gas Turbine Theory Second Edition, Cohen, Rogers and Saravanamuttoo, Longmans Group Limited 1972, ISBN   0 582 44927 8, p.85
15. Aero Engine Development for the Future, H.W. Bennett, Proc Instn Mech Engrs Vol 197A, Power Industries Division, July 1983, Fig.5
16. Paul Bevilaqua  : The shaft driven Lift Fan propulsion system for the Joint Strike Fighter Archived 2011-06-05 at the Wayback Machine page 3. Presented May 1, 1997. DTIC.MIL Word document, 5.5 MB. Accessed: 25 February 2012.
17. Bensen, Igor. "How they fly - Bensen explains all Archived 2015-01-09 at the Wayback Machine " Gyrocopters UK. Accessed: 10 April 2014.
18. Johnson, Wayne. Helicopter theory pp3+32, Courier Dover Publications, 1980. Accessed: 25 February 2012. ISBN   0-486-68230-7
19. Wieslaw Zenon Stepniewski, C. N. Keys. Rotary-wing aerodynamics p3, Courier Dover Publications, 1979. Accessed: 25 February 2012. ISBN   0-486-64647-5
20. Philip Walsh, Paul Fletcher. "Gas Turbine Performance", page 36. John Wiley & Sons, 15 April 2008. Quote: "It has better fuel consumption than a turbojet or turbofan, due to a high propulsive efficiency.., achieving thrust by a high mass flow of air from the propeller at low jet velocity. Above 0.6 Mach number the turboprop in turn becomes uncompetitive, due mainly to higher weight and frontal area."
21. "Rolls-Royce Aero Engines" Bill Gunston, Patrick Stevens Limited, ISBN   1-85260-037-3, p.147
22. "Propeller thrust" Glenn Research Center (NASA)
23. "Turboprop Engine" Glenn Research Center (NASA)
24. Jane's All the World's Aircraft. 2005. pp. 850–853. ISSN   0075-3017.
25. "PW1000G". MTU. Archived from the original on 2018-08-18. Retrieved 2020-11-06.
26. "The Leap Engine". CFM International.
27. "GEnx". GE.