Cupronickel

Last updated

Cupronickel or copper-nickel (CuNi) is an alloy of copper that contains nickel and strengthening elements, such as iron and manganese. The copper content typically varies from 60 to 90 percent. (Monel is a nickel-copper alloy that contains a minimum of 52 percent nickel.)

Contents

Despite its high copper content, cupronickel is silver in colour. Cupronickel is highly resistant to corrosion by salt water, and is therefore used for piping, heat exchangers and condensers in seawater systems, as well as for marine hardware. It is sometimes used for the propellers, propeller shafts, and hulls of high-quality boats. Other uses include military equipment and chemical, petrochemical, and electrical industries. [1]

Another common 20th-century use of cupronickel was silver-coloured coins. For this use, the typical alloy has 3:1 copper to nickel ratio, with very small amounts of manganese.

In the past, true silver coins were debased with cupronickel, such as coins of the pound sterling from 1947 onward having their content replaced.

Name

Aside from cupronickel and copper-nickel, several other terms have been used to describe the material: the tradenames Alpaka or Alpacca, Argentan Minargent, the registered French term cuivre blanc, and the romanized Cantonese term Paktong, 白銅 (the French and Cantonese terms both meaning "white copper"); cupronickel is also occasionally referred to as hotel silver, plata alemana (Spanish for "German silver"), German silver, and Chinese silver. [2]

Applications

Marine engineering

Cupronickel alloys are used for marine applications [3] due to their resistance to seawater corrosion, good fabricability, and their effectiveness in lowering macrofouling levels. Alloys ranging in composition from 90% Cu–10% Ni to 70% Cu–30% Ni are commonly specified in heat exchanger or condenser tubes in a wide variety of marine applications. [4]

Important marine applications for cupronickel include:

Coinage

Five Swiss francs 5CHFr.jpg
Five Swiss francs
Five Indian rupees, commemorating ILO. ILO 5 rs commemorative coin India.jpg
Five Indian rupees, commemorating ILO.

The successful use of cupronickel in coinage is due to its corrosion resistance, electrical conductivity, durability, malleability, low allergy risk, ease of stamping, antimicrobial properties and recyclability. [12]

In Europe, Switzerland pioneered the nickel billon coinage in 1850, with the addition of silver. In 1968, Switzerland adopted the far cheaper 75:25 copper to nickel ratio then being used in Belgium, the United States and Germany. From 1947 to 2012, all "silver" coinage in the UK was made from cupronickel, but from 2012 onwards the two smallest cupronickel denominations were replaced with lower-cost nickel-plated steel coins.

In part due to silver hoarding in the Civil War, the United States Mint first used cupronickel for circulating coinage in three-cent pieces starting in 1865, and then for five-cent pieces starting in 1866. Prior to these dates, both denominations had been made only in silver in the United States. Cupronickel is the cladding on either side of United States half-dollars (50¢) since 1971, and all quarters (25¢) and dimes (10¢) made after 1964. Currently, some circulating coins, such as the United States Jefferson nickel (5¢), [13] the Swiss franc, and the South Korean 500 and 100 won are made of solid cupronickel (75:25 ratio). [14]

Other usage

A thermocouple junction is formed from a pair of thermocouple conductors such as iron-constantan, copper-constantan or nickel-chromium/nickel-aluminium. The junction may be protected within a sheath of copper, cupronickel or stainless steel. [15]

Cupronickel is used in cryogenic applications. Its combination of good ductility retention and thermal conductivity at very low temperatures is advantageous for low-temperature processing and storage equipment as well as for heat exchangers at cryogenic plants. [16] [17] [18]

Beginning around the turn of the 20th century, bullet jackets were commonly made from this material. It was soon replaced with gilding metal to reduce metal fouling in the bore.

Currently, cupronickel and nickel silver remain the basic material for silver-plated cutlery. It is commonly used for mechanical and electrical equipment, medical equipment, zippers, jewelry items, and both for strings for instruments in the violin family, and for guitar frets. Fender Musical Instruments used "CuNiFe" magnets in their "Wide Range Humbucker" pickup for various Telecaster and Starcaster guitars during the 1970s.[ citation needed ]

For high-quality cylinder locks and locking systems, cylinder cores are made from wear-resistant cupronickel.

Cupronickel has been used as an alternative to traditional steel brake lines, as it does not rust. Since cupronickel is much softer than steel, it bends and flares more easily, and the same property allows it to form a better seal with hydraulic components.

Properties

Cupronickel lacks a copper color due to nickel's high electronegativity, which causes a loss of one electron in copper's d-shell (leaving 9 electrons in the d-shell versus pure copper's typical 10 electrons).

Important properties of cupronickel alloys include corrosion resistance, inherent resistance to macrofouling, good tensile strength, excellent ductility when annealed, thermal conductivity and expansion characteristics amenable for heat exchangers and condensers, good thermal conductivity and ductility at cryogenic temperatures and beneficial antimicrobial touch surface properties. [19]

Properties of some Cu–Ni alloys [20]
AlloyDensity
g/cm3
Thermal conductivity
W/(m·K)
TEC
μm/(m·K)
Electrical resistivity
μOhm·cm
Elastic modulus
GPa
Yield strength
MPa
Tensile strength
MPa
90–108.9401719135105275
70–308.95291634152125360
66–30–2–28.862515.550156170435

The alloys are:

UNS standard compositions* of wrought alloys (in at%). Maximum or range.
Alloy UNS No.Common nameEuropean specNiFeMnCu
C7060090–10CuNi10Fe9–111–1.81Balance
C7150070–30CuNi30Fe29–330.4–1.01Balance
C7164066–30–2–229–321.7–2.31.5–2.5Balance

Subtle differences in corrosion resistance and strength determine which alloy is selected. Descending the table, the maximum allowable flow rate in piping increases, as does the tensile strength.

In seawater, the alloys have excellent corrosion rates which remain low as long as the maximum design flow velocity is not exceeded. This velocity depends on geometry and pipe diameter. They have high resistance to crevice corrosion, stress corrosion cracking and hydrogen embrittlement that can be troublesome to other alloy systems. Copper-nickels naturally form a thin protective surface layer over the first several weeks of exposure to seawater and this provides its ongoing resistance. Additionally, they have a high inherent biofouling resistance to attachment by macrofoulers (e.g. seagrasses and molluscs) living in the seawater. To use this property to its full potential, the alloy needs to be free of the effects of, or insulated from, any form of cathodic protection.

However, Cu–Ni alloys can show high corrosion rates in polluted or stagnant seawater when sulfides or ammonia are present. It is important, therefore, to avoid exposure to such conditions, particularly during commissioning and refit while the surface films are maturing. Ferrous sulfate dosing to sea water systems can provide improved resistance.

Crack in 90-10 Cu-Ni metal plate due to stresses during silver brazing Crack in CuNi metal due to silver brazing.jpg
Crack in 90–10 Cu–Ni metal plate due to stresses during silver brazing

As copper and nickel alloy with each other easily and have simple structures, the alloys are ductile and readily fabricated. Strength and hardness for each individual alloy is increased by cold working; they are not hardened by heat treatment. Joining of 90–10 (C70600) and 70–30 (C71500) is possible by both welding or brazing. They are both weldable by the majority of techniques, although autogenous (welding without weld consumables) or oxyacetylene methods are not recommended. The 70–30 rather than 90–10 weld consumables are normally preferred for both alloys and no after-welding heat treatment is required. They can also be welded directly to steel, providing a 65% nickel-copper weld consumable is used to avoid iron dilution effects. The C71640 alloy tends to be used as seamless tubing and expanded rather than welded into the tube plate. Brazing requires appropriate silver-base brazing alloys. However, great care must be taken to ensure that there are no stresses in the Cu–Ni being silver brazed, since any stress can cause intergranulary penetration of the brazing material, and severe stress cracking (see image). Thus, full annealing of any potential mechanical stress is necessary.

Applications for Cu–Ni alloys have withstood the test of time, as they are still widely used and range from seawater system piping, condensers and heat exchangers in naval vessels, commercial shipping, multiple-stage flash desalination and power stations. They have also been used as splash zone cladding on offshore structures and protective cladding on boat hulls, as well as for solid hulls themselves.

Fabrication

Due to its ductility, cupronickel alloys can be readily fabricated in a wide variety of product forms [21] and fittings. Cupronickel tubing can be readily expanded into tube sheets for the manufacturing of shell and tube heat exchangers.

Details of fabrication procedures, including general handling, cutting and machining, forming, heat treatment, preparing for welding, weld preparations, tack welding, welding consumables, welding processes, paintina, mechanical properties of welds, and tube and pipe bending are available. [22]

Standards

ASTM, EN, and ISO standards exist for ordering wrought and cast forms of cupronickel. [23]

Thermocouples and resistors whose resistance is stable across changes in temperature contain alloy constantan, which consists of 55% copper and 45% nickel.

History

Chinese history

Cupronickel alloys were known as "white copper" to the Chinese since about the third century BC. Some weapons made during the Warring States period were made with Cu-Ni alloys. [24] The theory of Chinese origins of Bactrian cupronickel was suggested in 1868 by Flight, who found that the coins considered the oldest cupronickel coins yet discovered were of a very similar alloy to Chinese paktong. [25]

The author-scholar, Ho Wei, precisely described the process of making cupronickel in about 1095 AD. The paktong alloy was described as being made by adding small pills of naturally occurring yunnan ore to a bath of molten copper. When a crust of slag formed, saltpeter was added, the alloy was stirred and the ingot was immediately cast. Zinc is mentioned as an ingredient but there are no details about when it was added. The ore used is noted as solely available from Yunnan, according to the story:

"San Mao Chun were at Tanyang during a famine year when many people died, so taking certain chemicals, Ying projected them onto silver, turning it into gold, and he also transmuted iron into silver – thus enabling the lives of many to be saved [through purchasing grain through this fake silver and gold] Thereafter all those who prepared chemical powders by heating and transmuting copper by projection called their methods "Tanyang techniques". [25]

The late Ming and Qing literature have very little information about paktong. However, it is first mentioned specifically by name in the Thien Kung Khai Wu of circa 1637:

"When lu kan shih (zinc carbonate, calamine) or wo chhein (zinc metal) is mixed and combined with chih thung (copper), one gets 'yellow bronze' (ordinary brass). When phi shang and other arsenic substances are heated with it, one gets 'white bronze' or white copper: pai thong. When alum and niter and other chemicals are mixed together one gets ching thung: green bronze." [25]

Ko Hung stated in 300 AD: "The Tanyang copper was created by throwing a mercuric elixir into Tanyang copper and heated- gold will be formed." However, the Pha Phu Tsu and the Shen I Ching describing a statue in the Western provinces as being of silver, tin, lead and Tanyang copper – which looked like gold, and could be forged for plating and inlaying vessels and swords. [25]

Joseph Needham et al. argue that cupronickel was at least known as a unique alloy by the Chinese during the reign of Liu An in 120 BC in Yunnan. Moreover, the Yunnanese State of Tien was founded in 334 BC as a colony of the Chu. Most likely, modern paktong was unknown to Chinese of the day – but the naturally occurring Yunnan ore cupronickel alloy was likely a valuable internal trade commodity. [25]

Greco-Bactrian coinage

In 1868, W. Flight discovered a Greco-Bactrian coin comprising 20% nickel that dated from 180 to 170 BCE with the bust of Euthydemus II on the obverse. Coins of a similar alloy with busts of his younger brothers, Pantaleon and Agathocles, were minted around 170 BCE. The composition of the coins was later verified using the traditional wet method and X-ray fluorescence spectrometry. [25] Cunningham in 1873 proposed the "Bactrian nickel theory," which suggested that the coins must have been the result of overland trade from China through India to Greece. Cunningham's theory was supported by scholars such as W. W. Tarn, Sir John Marshall, and J. Newton Friend, but was criticized by E. R. Caley and S. van R. Cammann. [25]

In 1973, Cheng and Schwitter in their new analyses suggested that the Bactrian alloys (copper, lead, iron, nickel and cobalt) were closely similar to the Chinese paktong, and of nine known Asian nickel deposits, only those in China could provide the identical chemical compositions. [25] Cammann criticized Cheng and Schwitter's paper, arguing that the decline of cupronickel currency should not have coincided with the opening of the Silk Road. If the Bactrian nickel theory were true, according to Cammann, the Silk Road would have increased the supply of cupronickel. However, the end of Greco-Bactrian cupronickel currency could be attributed to other factors such as the end of the House of Euthydemus. [25]

European history

The alloy seems to have been rediscovered by the West during alchemy experiments. Notably, Andreas Libavius, in his Alchemia of 1597, mentions a surface-whitened copper aes album by mercury or silver. But in De Natura Metallorum in Singalarum Part 1, published in 1599, the same term was applied to "tin" from the East Indies (modern-day Indonesia and the Philippines) and given the Spanish name, tintinaso. [25]

Richard Watson of Cambridge appears to be the first to discover that cupronickel was an alloy of three metals. In attempting to rediscover the secret of white-copper, Watson critiqued Jean-Baptiste Du Halde's History of China (1688) as confusing the term paktong'., He noted the Chinese of his day did not form it as an alloy but rather smelted readily available unprocessed ore:

"...appeared from a vast series of experiments made at Peking- that it occurred naturally as an ore mined at the region, the most extraordinary copper is pe-tong or white copper: it is white when dug out of the mine and even more white within than without. It appears, by a vast number of experiments made at Peking, that its colour is owing to no mixture; on the contrary, all mixtures diminish its beauty, for, when it is rightly managed it looks exactly like silver and were there not a necessity of mixing a little tutenag or such metal to soften it, it would be so much more the extraordinary as this sort of copper is found no where but in China and that only in the Province of Yunnan". Notwithstanding what is here said, of the colour of the copper being owing to no mixture, it is certain the Chinese white copper as brought to us, is a mixt [sic: mixed] metal; so that the ore from which it was extracted must consist of various metallic substances; and from such ore that the natural orichalcum if it ever existed, was made." [25]

During the peak European importation of Chinese white-copper from 1750 to 1800, increased attention was made to its discovering its constituents. Peat and Cookson found that "the darkest proved to contain 7.7% nickel and the lightest said to be indistinguishable from silver with a characteristic bell-like resonance when struck and considerable resistance to corrosion, 11.1%".

Another trial by Andrew Fyfe estimated the nickel content at 31.6%. Guesswork ended when James Dinwiddie of the Macartney Embassy brought back in 1793, at considerable personal risk (smuggling of paktong ore was a capital crime by the Chinese Emperor), some of the ore from which paktong was made. [26] Cupronickel became widely understood, as published by E. Thomason, in 1823, in a submission, later rejected for not being new knowledge, to the Royal Society of Arts.

Efforts in Europe to exactly duplicate the Chinese paktong failed due to a general lack of requisite complex cobalt-nickel-arsenic naturally occurring ore. However, the Schneeberg district of Germany, where the famous Blaufarbenwerke made cobalt blue and other pigments, solely held the requisite complex cobalt-nickel-arsenic ores in Europe.

At the same time, the Prussian Verein zur Beförderung des Gewerbefleißes (Society for the Improvement of Business Diligence/Industriousness) offered a prize for the mastery of the process. Unsurprisingly, Dr E.A. Geitner and J.R. von Gersdoff of Schneeberg won the prize and launched their "German silver" brand under the trade names Argentan and Neusilber (new silver). [26]

In 1829, Percival Norton Johnston persuaded Dr. Geitner to establish a foundry in Bow Common behind Regents' Park Canal in London, and obtained ingots of nickel-silver with the composition 18% Ni, 55% Cu and 27% Zn. [26]

Between 1829 and 1833, Percival Norton Johnson was the first person to refine cupronickel on the British Isles. He became a wealthy man, producing in excess of 16.5 tonnes per year. The alloy was mainly made into cutlery by the Birmingham firm William Hutton and sold under the trade-name "Argentine".

Johnsons' most serious competitors, Charles Askin and Brok Evans, under the brilliant chemist Dr. EW Benson, devised greatly improved methods of cobalt and nickel suspension and marketed their own brand of nickel-silver, called "British Plate". [26]

By the 1920s, a 70–30 copper-nickel grade was developed for naval condensers. Soon afterwards, a 2% manganese and 2% iron alloy now known as alloy C71640 was introduced for a UK power station which needed better erosion resistance because the levels of entrained sand in the seawater. A 90–10 alloy first became available in the 1950s, initially for seawater piping, and is now the more widely used alloy.

See also

Related Research Articles

Metallurgy Domain of materials science that studies the physical and chemical behavior of metals

Metallurgy is a domain of materials science and engineering that studies the physical and chemical behavior of metallic elements, their inter-metallic compounds, and their mixtures, which are known as alloys. Metallurgy encompasses both the science and the technology of metals; that is, the way in which science is applied to the production of metals, and the engineering of metal components used in products for both consumers and manufacturers. Metallurgy is distinct from the craft of metalworking. Metalworking relies on metallurgy in a similar manner to how medicine relies on medical science for technical advancement. A specialist practitioner of metallurgy is known as a metallurgist.

Stainless steel Steel alloy resistant to corrosion

Stainless steel is any of a group of ferrous alloys that contain a minimum of approximately 11% chromium, a composition that largely inhibits the iron from rusting and provides heat-resistant properties. Different types of stainless steel include the elements carbon, nitrogen, aluminium, silicon, sulfur, titanium, nickel, copper, selenium, niobium, and molybdenum. Specific types of stainless steel are often designated by their AISI three-digit number, e.g., 304 stainless. The ISO 15510 standard lists the chemical compositions of stainless steels of the specifications in existing ISO, ASTM, EN, JIS, and GB standards in a useful interchange table.

Solder Alloy used to join metal pieces

Solder is a fusible metal alloy used to create a permanent bond between metal workpieces. Solder is melted in order to wet the parts of the joint, where it adheres to and connects the pieces after cooling. Metals or alloys suitable for use as solder should have a lower melting point than the pieces to be joined. The solder should also be resistant to oxidative and corrosive effects that would degrade the joint over time. Solder used in making electrical connections also needs to have favorable electrical characteristics.

Copper Chemical element, symbol Cu and atomic number 29

Copper is a chemical element with the symbol Cu and atomic number 29. It is a soft, malleable, and ductile metal with very high thermal and electrical conductivity. A freshly exposed surface of pure copper has a pinkish-orange color. Copper is used as a conductor of heat and electricity, as a building material, and as a constituent of various metal alloys, such as sterling silver used in jewelry, cupronickel used to make marine hardware and coins, and constantan used in strain gauges and thermocouples for temperature measurement.

Metalworking Process of making items from metal

Metalworking is the process of shaping and reshaping metals to create useful objects, parts, assemblies, and large scale structures. As a term it covers a wide and diverse range of processes, skills, and tools for producing objects on every scale: from huge ships, buildings, and bridges down to precise engine parts and delicate jewelry.

Nickel silver Shiny alloy of copper, nickel, and zinc

Nickel silver, Maillechort, German silver, Argentan, new silver, nickel brass, albata, alpacca, is a copper alloy with nickel and often zinc. The usual formulation is 60% copper, 20% nickel and 20% zinc. Nickel silver does not contain the element silver. It is named for its silvery appearance, which can make it attractive as a cheaper and more durable substitute. It is also well suited for being plated with silver. A naturally occurring ore composition in China was smelted into the alloy known as paktong or baitong (白銅). The name "German Silver" refers to the artificial recreation of the natural ore composition by German metallurgists. All modern, commercially important nickel silvers contain significant amounts of zinc, and are sometimes considered a subset of brass.

Brazing High-temperature soldering; metal-joining technique by high-temperature molten metal filling

Brazing is a metal-joining process in which two or more metal items are joined together by melting and flowing a filler metal into the joint, with the filler metal having a lower melting point than the adjoining metal.

Monel Solid-solution binary alloy of nickel and copper

Monel is a group of alloys of nickel and copper, with small amounts of iron, manganese, carbon, and silicon. Monel is not a cupronickel alloy because it has less than 60% copper.

Titanium alloys are alloys that contain a mixture of titanium and other chemical elements. Such alloys have very high tensile strength and toughness. They are low density so relatively light in weight, have extraordinary corrosion resistance and a low thermal expansion coefficient, which means they can withstand extreme temperatures. However, the high cost of both raw materials and processing limit their use to military applications, aircraft, spacecraft, bicycles, medical devices, jewelry, highly stressed components such as connecting rods on expensive sports cars and some premium sports equipment and consumer electronics.

Aluminium bronze

Aluminium bronze is a type of bronze in which aluminium is the main alloying metal added to copper, in contrast to standard bronze or brass. A variety of aluminium bronzes of differing compositions have found industrial use, with most ranging from 5% to 11% aluminium by weight, the remaining mass being copper; other alloying agents such as iron, nickel, manganese, and silicon are also sometimes added to aluminium bronzes.

Orthodontic archwire Wire used in dental braces

An archwire in orthodontics is a wire conforming to the alveolar or dental arch that can be used with dental braces as a source of force in correcting irregularities in the position of the teeth. An archwire can also be used to maintain existing dental positions; in this case it has a retentive purpose.

Intergranular corrosion

Intergranular corrosion (IGC), also known as intergranular attack (IGA), is a form of corrosion where the boundaries of crystallites of the material are more susceptible to corrosion than their insides.

Glidcop is a family of copper-based metal matrix composite (MMC) alloys mixed primarily with small amounts of aluminum oxide ceramic particles. It is a trademark of North American Höganäs. The name is sometimes written GlidCop or GLIDCOP.

Group 11 element Group of elements in the poriodic table containing copper, silver and gold

Group 11, by modern IUPAC numbering, is a group of chemical elements in the periodic table, consisting of copper (Cu), silver (Ag), and gold (Au). Roentgenium (Rg) is also placed in this group in the periodic table, although no chemical experiments have yet been carried out to confirm that it behaves like the heavier homologue to gold. Group 11 is also known as the coinage metals, due to their usage in minting coins—while the rise in metal prices mean that silver and gold are no longer used for circulating currency, remaining in use for bullion, copper remains a common metal in coins to date, either in the form of copper clad coinage or as part of the cupronickel alloy. They were most likely the first three elements discovered. Copper, silver, and gold all occur naturally in elemental form.

Melchior (alloy)

In metallurgy, melchior is an alloy of copper, mainly with nickel (5–30%). Its name originates from Italian: melchior, which in turn is distorted French: maillechort, honoring the French inventors of the alloy, Maillot and Chorier. The term melchior sometimes refers not only to the copper-nickel alloys, but also ternary alloys of copper with nickel and zinc and even a silvered brass. Melchior is easily deformable by application of pressure, both in the hot and cold state. After annealing, it has a tensile strength of about 40 kg/mm2. The most valuable property of melchior is its high resistance to corrosion in air, freshwater and seawater. Increasing content of nickel, iron or manganese improves corrosion and cavitation resistance, especially in sea water and atmospheric water vapor. The alloy of 30% Ni, 0.8% Fe, 1% Mn and 68.2% Cu is used in maritime shipping, in particular for the manufacture of condenser tubes. Nickel gives melchior, unlike brass and bronze, a silver color, and that property, combined with its high corrosion resistance, made it popular for the manufacture of household utensils in the Soviet Union, though more recent research has concluded that nickel is mildly carcinogenic when used in food preparation and consumption.

Copper alloys in aquaculture

Copper alloys are important netting materials in aquaculture. Various other materials including nylon, polyester, polypropylene, polyethylene, plastic-coated welded wire, rubber, patented twine products, and galvanized steel are also used for netting in aquaculture fish enclosures around the world. All of these materials are selected for a variety of reasons, including design feasibility, material strength, cost, and corrosion resistance.

Materials for use in vacuum

Materials for use in vacuum are materials that show very low rates of outgassing in vacuum and, where applicable, are tolerant to bake-out temperatures. The requirements grow increasingly stringent with the desired degree of vacuum to be achieved in the vacuum chamber. The materials can produce gas by several mechanisms. Molecules of gases and water can be adsorbed on the material surface. Materials may sublimate in vacuum. Or the gases can be released from porous materials or from cracks and crevices. Traces of lubricants, residues from machining, can be present on the surfaces. A specific risk is outgassing of solvents absorbed in plastics after cleaning.

Heat exchangers are devices that transfer heat to achieve desired heating or cooling. An important design aspect of heat exchanger technology is the selection of appropriate materials to conduct and transfer heat fast and efficiently.

CuproBraze is a copper-alloy heat exchanger technology for harsh temperature and pressure environments such as those in the latest generations of cleaner diesel engines mandated by global environmental regulations. The technology, developed by the International Copper Association (ICA), is licensed free of charge to heat exchanger manufacturers around the world.

References

  1. Sakiewicz P.,Nowosielski R., Babilas R. Production aspects of inhomogeneous hot deformation in as-cast CuNi25 alloy, Indian Journal of Engineering & Materials Sciences, Vol. 22, August 2015, pp. 389-398
  2. Deutsches Kupfer-Institut (Hrsg.): Kupfer-Nickel-Zink-Legierungen. Berlin 1980.
  3. Marine Applications for Copper-Nickel Alloys http://www.copper.org/applications/marine/cuni/applications/#non_marine
  4. Kobelco: Copper alloy tubes for heat-exchanger; Shinko Metal Products, Japan; http://www.shinkometal.co.jp/catalog/copperalloy-en-sc.pdf Archived 2013-10-29 at the Wayback Machine
  5. Copper-Nickel Alloys in Boat and Ship Hulls http://www.copper.org/applications/marine/cuni/applications/hulls/
  6. Copper-Nickel Alloys in Shipbuilding and Repair http://www.copper.org/applications/marine/cuni/applications/shipbuilding_and_repair/
  7. Copper-Nickel Alloys in Desalination Plants http://www.copper.org/applications/marine/cuni/applications/desalination_plants/
  8. Copper-Nickel Alloys in Offshore Oil and Gas Platforms and Processing http://www.copper.org/applications/marine/cuni/applications/offshore_oil_and_gas/
  9. Copper-Nickel Alloys in Power Generation http://www.copper.org/applications/marine/cuni/applications/power_generation/
  10. Copper-Nickel Alloys in Seawater System Design http://www.copper.org/applications/marine/cuni/applications/seawater_system_design/
  11. Copper-Nickel Alloys in Seawater System Components http://www.copper.org/applications/marine/cuni/applications/seawater_system_components/
  12. Copper-Nickel in Coinage
  13. "The United States Mint: Coin Specifications" . Retrieved 2008-06-11.
  14. "Currency in Circulation: Introduction to Coins". Archived from the original on 2014-12-31. Retrieved 2010-09-27.
  15. Robert Monro Black, The history of electric wires and cables Science Museum (Great Britain), IET, 1983, ISBN   0-86341-001-4, p. 161
  16. Cryogenic Properties of Copper-Nickel http://www.copper.org/applications/marine/cuni/properties/cryogenic/
  17. Low-Temperature Properties of Copper and Copper Alloys http://www.copper.org/publications/pub_list/pdf/104-5-low-temperatuare.pdf
  18. Mechanical Properties of Copper and Copper Alloys at Low Temperatures http://www.copper.org/resources/properties/144_8/
  19. Properties of Copper-Nickel Alloys http://www.copper.org/applications/marine/cuni/properties/
  20. Physical Properties of Copper-Nickel
  21. "Copper-Nickel Alloy Product Forms". Copper Development Association Inc.
  22. "Copper-Nickel Alloy Fabrication". Copper Development Association Inc.
  23. Copper-Nickel Standards http://www.copper.org/applications/marine/cuni/standards/
  24. Ancient Chinese weapons Archived 2005-03-07 at the Wayback Machine and A halberd of copper-nickel alloy, from the Warring States Period. Archived 2012-05-27 at archive.today
  25. 1 2 3 4 5 6 7 8 9 10 11 Joseph Needham, Ling Wang, Gwei-Djen Lu, Tsuen-hsuin Tsien, Dieter Kuhn, Peter J Golas, Science and civilisation in China: Cambridge University Press: 1974, ISBN   0-521-08571-3, pp. 237–250
  26. 1 2 3 4 Mcneil I Staff, Ian McNeil Encyclopaedia of the History of Technology: Routledge: 2002: ISBN   0-203-19211-7: pp98