"PS/2" redirects here. For the video game console, see PlayStation 2. For the keyboard and mouse connectors introduced with this system, see PS/2 port. For other uses, see PS2 (disambiguation).
The PS/2 line was created by IBM partly in an attempt to recapture control of the PC market by introducing the advanced yet proprietaryMicro Channel architecture (MCA) on higher-end models. These models were in the strange position of being incompatible with the IBM-compatible hardware standards previously established by IBM and adopted in the PC industry. However IBM's initial PS/2 computers were popular with target market corporate buyers, and by 30th September 1988 IBM reported that it had sold 3 million PS/2 machines. This was only 18 months after the new range had been introduced.
Most major PC manufacturers balked at IBM's licensing terms for MCA-compatible hardware, particularly the per-machine royalties. In 1992, Macworld stated that "IBM lost control of its own market and became a minor player with its own technology."[3]
The OS/2operating system was announced at the same time as the PS/2 line and was intended to be the primary operating system for models with Intel 80286 or later processors. However, at the time of the first shipments, only IBM PC DOS 3.3 was available. OS/2 1.0 (text-mode only) and Microsoft's Windows 2.0 became available several months later. IBM also released AIX PS/2, a UNIX operating system for PS/2 models with Intel 386 or later processors.
IBM's PS/2 was designed to remain software compatible with their PC/AT/XT line of computers upon which the large PC clone market was built, but the hardware was quite different. PS/2 had two BIOSes: one named ABIOS (Advanced BIOS) which provided a new protected mode interface and was used by OS/2, and CBIOS (Compatible BIOS) which was included to be software compatible with the PC/AT/XT. CBIOS was so compatible that it even included Cassette BASIC. While IBM did not publish the BIOS source code, it did promise to publish BIOS entry points.[4]
With certain models to the IBM PS/2 line, Micro Channel Architecture (MCA) was also introduced.[4] MCA was conceptually similar to the channel architecture of the IBM System/360 mainframes. MCA was technically superior to ISA and allowed for higher speed communications within the system. The majority of MCA's features would be seen in later buses with the exception of: streaming-data procedure, channel-check reporting, error logging[5] and internal bus-level video pass-through for devices like the IBM 8514. Transfer speeds were on par with the much later PCI standard. MCA allowed one-to-one, card to card, and multi-card to processor simultaneous transaction management which is a feature of the PCI-X bus format.
Bus mastering capability, bus arbitration, and a primitive form of plug-and-play BIOS management of hardware were all benefits of MCA. (One book from the year 2000 writes: "MCA used an early (and user-hostile) version of what we know now as 'Plug-N′-Play', requiring a special setup disk for each machine and each card."[6] MCA never gained wide acceptance outside of the PS/2 line due to IBM's anti-clone practices [citation needed] and incompatibilities with ISA. IBM offered to sell an MCA license to anyone who could afford the royalty. However, royalties were required for every MCA-compatible machine sold and a payment for every IBM-compatible machine the particular maker had made in the past.[citation needed] There was nothing unique in IBM insisting on payment of royalties on the use of its patents applied to Micro Channel-based machines. Up until that time, some companies had failed to pay IBM for the use of its patents on the earlier generation of Personal Computer.
Keyboard/mouse
Layout
The PS/2 IBM Model M keyboard used the same 101-key layout of the previous IBM PC/AT Extended keyboard, itself derived from the original IBM PC keyboard.[4] European variants had 102 keys with the addition of an extra key to the right of the left Shift key.
The original IBM PS/2 mousePS/2 connection ports (later colored purple for keyboard and green for mouse, according to PC 97) were once commonly used for connecting input devices.
PS/2 systems introduced a new specification for the keyboard and mouse interfaces, which are still in use today (though increasingly supplanted by USB devices) and are thus called "PS/2" interfaces. The PS/2 keyboard interface, inspired by Apple's ADB interface, was electronically identical to the long-established AT interface, but the cable connector was changed from the 5-pin DIN connector to the smaller 6-pin mini-DIN interface. The same connector and a similar synchronous serial interface was used for the PS/2 mouse port.
The initial desktop Model 50 and Model 70 also featured a new cableless internal design, based on use of interposer circuit boards to link the internal drives to the planar (motherboard). Additionally these machines could be largely disassembled and reassembled for service without tools.
Additionally, the PS/2 introduced a new software data area known as the Extended BIOS Data Area (EBDA). Its primary use was to add a new buffer area for the dedicated mouse port. This also required making a change to the "traditional" BIOS Data Area (BDA) which was then required to point to the base address of the EBDA.
Another new PS/2 innovation was the introduction of bidirectional parallel ports which in addition to their traditional use for connecting a printer could now function as a high speed data transfer interface. This allowed the use of new hardware such as parallel port scanners, CD-ROM drives, and also enhanced the capabilities of printers by allowing them to communicate with the host PC and send back signals instead of simply being a passive output device.
Graphics
Most of the initial range of PS/2 models were equipped with a new frame buffer known as the Video Graphics Array, or VGA for short. This effectively replaced the previous EGA standard.[4] VGA increased graphics memory to 256KB and provided for resolutions of 640×480 with 16 colors, and 320×200 with 256 colors. VGA also provided a palette of 262,144 colors (as opposed to the EGA palette of 64 colors). The IBM 8514 and later XGAcomputer display standards were also introduced on the PS/2 line.
38F4737: 10", 640×480, non-interlaced, 1989, amber monochrome plasma screen; this display was exclusive to models P70 and P75
In truth, all "XGA" 1024×768 monitors are multimode, as XGA works as an add-on card to a built-in VGA and transparently passes-thru the VGA signal when not operating in a high resolution mode. All of the listed 85xx displays can therefore sync 640×480 at 60Hz (or 720×400 at 70Hz) in addition to any higher mode they may also be capable of. This however is not true of the 95xx models (and some unlisted 85xx's), which are specialist workstation displays designed for use with the XGA-2 or Image Adapter/A cards, and whose fixed frequencies all exceed that of basic VGA – the lowest of their commonly available modes instead being 640×480 at 75Hz, if not something much higher still. It is also worth noting that these were still merely dual- or "multiple-frequency" monitors, not variable-frequency (also known as multisync); in particular, despite running happily at 640×480/720×400 and 1024×768, an (e.g.) 8514 cannot sync the otherwise common intermediate 800×600 "SVGA" resolution, even at the relatively low 50 to 56Hz refresh rates initially used.
Although the design of these adapters did not become an industry standard as VGA did, their 1024×768 pixel resolution was subsequently widely adopted as a standard by other manufacturers, and "XGA" became a synonym for this screen resolution. The lone exception were the bottom-rung 8086-based Model 25 and 30, which had a cut-down version of VGA referred to as MCGA; the 286 models came with VGA. This supported CGA graphics modes, VGA 320x200x256 and 640x480x2 mode, but not EGA or color 640x480.
MCA IBM XGA-2 Graphics Card
VGA video connector
All of the new PS/2 graphics systems (whether MCGA, VGA, 8514, or later XGA) used a 15-pin D-sub connector for video out. This used analog RGB signals, rather than four or six digital color signals as on previous CGA and EGA monitors. The digital signals limited the color gamut to a fixed 16 or 64 color palette with no room for expansion. In contrast, any color depth (bits per primary) can be encoded into the analog RGB signals so the color gamut can be increased arbitrarily by using wider (more bits per sample) DACs and a more sensitive monitor. The connector was also compatible with analog grayscale displays. Unlike earlier systems (like MDA and Hercules) this was transparent to software, so all programs supporting the new standards could run unmodified whichever type of display was attached. (On the other hand, whether the display was color or monochrome was undetectable to software, so selection between application displays optimized for color or monochrome, in applications that supported both, required user intervention.) These grayscale displays were relatively inexpensive during the first few years the PS/2 was available, and they were very commonly purchased with lower-end models.
The VGA connector became the de facto standard for connecting monitors and projectors on both PC and non-PC hardware over the course of the early 1990s, replacing a variety of earlier connectors.
Storage
Some PS/2 models used a quick-attachment socket on the back of the floppy drive which is incompatible with a standard 5.25" floppy connector.Close-up of unusual 72-pin MCA internal hard drive connector
Apple had first popularized the 3.5" floppy on the Macintosh line and IBM brought them to the PC in 1986 with the PC Convertible. In addition, they could be had as an optional feature on the XT and AT. The PS/2 line used entirely 3.5" drives which assisted in their quick adoption by the industry, although the lack of 5.25" drive bays in the computers created problems later on in the 1990s as they could not accommodate internal CD-ROM drives. In addition, the lack of built-in 5.25" floppy drives meant that PS/2 users could not immediately run the large body of existing IBM compatible software.[7] However IBM made available optional external 5.25" drives, with internal adapters for the early PS/2 models, to enable data transfer.
3.5" DD and HD floppies
In the initial lineup, IBM used 720KB double density (DD) capacity drives on the 8086-based models and 1440KB high density (HD) on the 80286-based and higher models. By the end of the PS/2 line they had moved to a somewhat standardized capacity of 2880KB.
The PS/2 floppy drives lacked a capacity detector. 1440KB floppies had a hole so that drives could identify them from 720KB floppies, preventing users from formatting the smaller capacity disks to the higher capacity (doing so would work, but with a higher tendency of data loss). Clone manufacturers implemented the hole detection, but IBM did not. As a result of this a 720 KB floppy could be formatted to 1440KB in a PS/2, but the resulting floppy would only be readable by a PS/2 machine.[8]
PS/2s primarily used Mitsubishi floppy drives and did not use a separate Molex power connector; the data cable also contained the power supply lines. As the hardware aged the drives often malfunctioned due to bad quality capacitors.[citation needed]
The PS/2 used several different types of internal hard drives. Early models used MFM or ESDI drives. Some desktop models used combo power/data cables similar to the floppy drives. Later models used DBA ESDI or Parallel SCSI. Typically, desktop PS/2 models only permitted use of one hard drive inside the computer case. Additional storage could be attached externally using the optional SCSI interface.
Memory
Later PS/2 models introduced the 72-pin SIMM[9] which became the de facto standard for RAM modules by the mid-1990s in mid-to-late 486 and nearly all Pentium desktop systems. 72-pin SIMMs were 32/36 bits wide and replaced the old 30-pin SIMM (8/9-bit) standard. The older SIMMs were much less convenient because they had to be installed in sets of two or four to match the width of the CPU's 16-bit (Intel 80286 and 80386SX) or 32-bit (80386 and 80486) data bus, and would have been extremely inconvenient to use in Pentium systems (which featured a 64-bit memory bus). 72-pin SIMMs were also made with greater capacities (starting at 1mb and ultimately reaching 128mb, vs 256kb to 16mb and more commonly no more than 4mb for 30-pin) and in a more finely graduated range (powers of 2, instead of powers of 4).
Many PS/2 models also used proprietary IBM SIMMs and could not be fitted with commonly available types. However industry standard SIMMs could be modified to work in PS/2 machines if the presence and type detection bridges or associated contacts were correctly rewired.
Models
At launch, the PS/2 family comprised the Model 30, 50, 60 and 80;[4] the Model 25 was launched a few months later.
The PS/2 Models 25 and 30 (IBM 8525 and 8530, respectively) were the lowest-end models in the lineup and meant to replace the IBM PC and XT. Model 25s came with either an 8086 CPU running at 8MHz, 512KB of RAM, and 720KB floppy disks, or 80286 CPU. The 8086s had ISA expansion slots and a built-in MCGA monitor, which could be either color or monochrome, while the 80286 models came with VGA monitor and ISA expansion slots. A cut-down Model M with no numeric keypad was standard, with the normal keyboard being an extra-cost option. There was a very rare later model called the PS/2 Model 25-SX which sported either a 16MHz or 20MHz 386 CPU, up to 12MB of memory, IDE hard drive, VGA Monitor and 16bit ISA slots making it the highest available model 25 available denoted by model number 8525-L41.
Case badge on model 25-SX 386-20 8525-L41
The Model 30 had either an 8086 or 286 CPU and sported the full 101-key keyboard and standalone monitor along with three 8-bit ISA expansion slots. 8086 models had 720KB floppies while 286 models had 1440KB ones. Both the Model 25 and 30 could have an optional 20MB ST-506 hard disk (which in the Model 25 took the place of the second floppy drive if so equipped and used a proprietary 3.5" form factor). 286-based Model 30s are otherwise a full AT-class machine and support up to 4MB of RAM.
IBM Personal System/2 Model 25
Later ISA PS/2 models comprised the Model 30-286 (a Model 30 with an Intel 286 CPU), Model 35 (IBM 8535) and Model 40 (IBM 8540) with Intel 386SX or IBM 386SLC processors.
The higher-numbered models (above 50) were equipped with the Micro Channel bus and mostly ESDI or SCSIhard drives (models 60-041 and 80-041 had MFM hard drives). PS/2 Models 50 (IBM 8550) and 60 (IBM 8560) used the Intel 286 processor, the PS/2 Models 70 (IBM 8570) and 80 used the 386DX, while the mid-range PS/2 Model 55SX (IBM 8555-081) and used the 16/32-bit 386SX processor. The Model 50 was revised to the Model 50Z still with 10MHz 80286 processor, but with memory run at zero wait state, and a switch to ESDI hard drives. Later Model 70 and 80 variants (B-xx) also used 25MHz Intel 486 processors, in a complex called the Power Platform.
The externally very similar Models 60 and 80 next to each otherIBM Model 70 (case open over case closed)
The PS/2 Models 90 (IBM 8590/9590) and 95 (IBM 8595/9595/9595A) used Processor Complex daughterboards holding the CPU, memory controller, MCA interface, and other system components. The available Processor Complex options ranged from the 20MHz Intel 486 to the 90MHz Pentium and were fully interchangeable. The IBM PC Server 500, which has a motherboard identical to the 9595A, also uses Processor Complexes.
Other later Micro Channel PS/2 models included the Model 65SX with a 16MHz 386SX; various Model 53 (IBM 9553), 56 (IBM 8556) and 57 (IBM 8557) variants with 386SX, 386SLC or 486SLC2 processors; the Models 76 and 77 (IBM 9576/9577) with 486SX or 486DX2 processors respectively; and the 486-based Model 85 (IBM 9585).
The IBM PS/2E (IBM 9533) was the first Energy Star compliant personal computer. It had a 50MHz IBM 486SLC processor, an ISA bus, four PC card slots, and an IDE hard drive interface. The environmentally friendly PC borrowed many components from the ThinkPad line and was composed of recycled plastics, designed to be easily recycled at the end of its life, and used very little power.
The IBM PS/2 Server 195 and 295 (IBM 8600) were 486-based dual-bus MCA network servers supporting asymmetric multiprocessing, designed by Parallan Computer Inc.
The IBM PC Server 720 (IBM 8642) was the largest MCA-based server made by IBM, although it was not, strictly speaking, a PS/2 model. It could be fitted with up to six Intel Pentium processors interconnected by the Corollary C-bus and up to eighteen SCSI hard disks. This model was equipped with seven combination MCA/PCI slots.
PS/2 N33SX laptop (1992)
IBM also produced several portable and laptop PS/2s, including the Model L40 (ISA-bus 386SX), N33 (IBM's first notebook-format computer from year 1991, Model 8533, 386SX), N51 (386SX/SLC), P70 (386DX) and P75 (486DX2).
The IBM ThinkPad 700C, aside from being labeled "700C PS/2" on the case, featured MCA and a 486SLC CPU.
The 6152 Academic System was a workstation computer developed by IBM's Academic Information Systems (ACIS) division for the university market introduced in February 1988. The 6152 was based on the PS/2 Model 60, adding a RISC Adapter Card on the Micro Channel bus. This card was a co-processor that enabled the 6152 to run ROMP software compiled for IBM's Academic Operating System (AOS), a version of BSD UNIX for the ROMP that was only available to select colleges and universities.[10]
The RISC Adapter Card contained the ROMP-C microprocessor (an enhanced version of the ROMP that first appeared in the IBM RT PC workstations), a memory management unit (the ROMP had virtual memory), a floating-pointcoprocessor, and up to 8MB of memory for use by the ROMP.[11] The 6152 was the first computer to use the ROMP-C, which would later be introduced in new RT PC models.[12]
Marketing
During the 1980s, IBM's advertising of the original PC and its other product lines had frequently used the likeness of Charlie Chaplin. For the PS/2, however, IBM augmented this character with a notorious jingle that seemed more suitable for a low-end consumer product than a business-class computing platform:
How ya gonna do it? PS/2 it! It's as easy as IBM. (or The solution is IBM.)
Another campaign featured actors from the television show M*A*S*H playing the staff of a contemporary (i.e. late-1980s) business in roles reminiscent of their characters' roles from the series. Harry Morgan, Larry Linville, William Christopher, Wayne Rogers, Gary Burghoff, Jamie Farr, and Loretta Swit were in from the beginning, whereas Alan Alda joined the campaign later.[13]
The profound lack of success of these advertising campaigns led, in part, to IBM's termination of its relationships with its global advertising agencies; these accounts were reported by Wired magazine to have been worth over $500 million a year, and the largest such account review in the history of business.[14]
Overall, the PS/2 line was largely unsuccessful with the consumer market, even though the PC-based Models 30 and 25 were an attempt to address that. With what was widely seen as a technically competent but cynical attempt to gain undisputed control of the market, IBM unleashed an industry backlash, which went on to standardize VESA, EISA and PCI. In large part, IBM failed to establish a link in the consumer's mind between the PS/2 MicroChannel architecture and the immature OS/2 1.x operating system; the more capable OS/2 version 2.0 did not release until 1992.[15]
The firm suffered massive financial losses for the remainder of the 1980s, forfeiting its previously unquestioned position as the industry leader, and eventually lost its status as the largest manufacturer of personal computers, first to Compaq and then to Dell. From a high of 10,000 employees in Boca Raton before the PS/2 came out, only seven years later, IBM had $600 million in unsold inventory and was laying off staff by the thousands.[16][17][full citation needed] After the failure of the PS/2 line to establish a new standard, IBM was forced to revert to building ISA PCs—following the industry it had once led—with the low-end PS/1 line and later with the more compatible Aptiva and PS/ValuePoint lines.
Still, the PS/2 platform experienced some success in the corporate sector where the reliability, ease of maintenance and strong corporate support from IBM offset the rather daunting cost of the machines. Also, many people still lived with the motto "Nobody ever got fired for buying an IBM". In the mid-range desktop market, the models 55SX and later 56SX were the leading sellers for almost their entire lifetimes. Later PS/2 models saw a production life span that took them into the late 1990s, within a few years of IBM selling off the division.
Industry Standard Architecture (ISA) is the 16-bit internal bus of IBM PC/AT and similar computers based on the Intel 80286 and its immediate successors during the 1980s. The bus was (largely) backward compatible with the 8-bit bus of the 8088-based IBM PC, including the IBM PC/XT as well as IBM PC compatibles.
The Intel 80486, also known as the i486 or 486, is a higher-performance follow-up to the Intel 80386 microprocessor. The 80486 was introduced in 1989 and was the first tightly pipelined x86 design as well as the first x86 chip to use more than a million transistors, due to a large on-chip cache and an integrated floating-point unit. It represents a fourth generation of binary compatible CPUs since the original 8086 of 1978.
Amstrad was a British electronics company, founded in 1968 by Alan Sugar at the age of 21. The name is a contraction of Alan Michael Sugar Trading. It was first listed on the London Stock Exchange in April 1980. During the late 1980s, Amstrad had a substantial share of the PC market in the UK. Amstrad was once a FTSE 100 Index constituent but since 2007 is wholly owned by Sky UK. As of 2006, Amstrad's main business was manufacturing Sky UK interactive boxes. In 2010 Sky integrated Amstrad's satellite division as part of Sky so they could make their own set-top boxes in-house.
The Tandy 1000 was the first in a line of IBM PC compatible home computer systems produced by the Tandy Corporation for sale in its Radio Shack and Radio Shack Computer Center chains of stores.
IBM 8514 is an IBM graphics computer display standard supporting a display resolution of 1024x768 pixels with 256 colors at 43.5 Hz, or 640x480 at 60 Hz (non-interlaced). 8514 usually refers to the display controller hardware However, IBM sold the companion CRT monitor which carries the same designation, 8514.
Video Graphics Array (VGA) is a video display controller and accompanying de facto graphics standard, first introduced with the IBM PS/2 line of computers in 1987, which became ubiquitous in the PC industry within three years. The term can now refer either to the computer display standard, the 15-pin D-subminiature VGA connector, or the 640×480 resolution characteristic of the VGA hardware.
Micro Channel architecture, or the Micro Channel bus, was a proprietary 16- or 32-bit parallel computer bus introduced by IBM in 1987 which was used on PS/2 and other computers until the mid-1990s. Its name is commonly abbreviated as "MCA", although not by IBM. In IBM products, it superseded the ISA bus and was itself subsequently superseded by the PCI bus architecture.
The IBM PC Convertible is a laptop computer made by IBM, first sold in April 1986. The Convertible was IBM's first laptop-style computer, following the luggable IBM Portable, and introduced the 3½-inch floppy disk format to the IBM product line. Like modern laptops, it featured power management and the ability to run from batteries.
The Gateway Handbook was a very small and lightweight subnotebook originally introduced by Gateway Computers in 1992. It quickly achieved critical acclaim and a cult-like following, especially in Japan.
The FM Towns is a Japanese variant of PC, built by Fujitsu from February 1989 to the summer of 1997. It started as a proprietary PC variant intended for multimedia applications and PC games, but later became more compatible with IBM PC compatibles. In 1993, the FM Towns Marty was released, a game console compatible with existing FM Towns games.
The Sun386i is a discontinued hybrid UNIX workstation/PC compatible computer system produced by Sun Microsystems, launched in 1988. It is based on the Intel 80386 microprocessor but shares many features with the contemporary Sun-3 series systems.
RM Nimbus was a range of personal computers from British company Research Machines sold from 1985 until the early 1990s, after which the designation Nimbus was discontinued. The first of these computers, the RM Nimbus PC-186, was not IBM PC compatible, but its successors the PC-286 and PC-386 were. RM computers were predominantly sold to schools and colleges in the United Kingdom for use as LAN workstations in classrooms.
The IBM PS/ValuePoint personal computer was IBM's answer to the PC clone market, where the IBM PS/2 could not compete due to price and proprietary interfaces. Announced in October 1992 and withdrawn in July 1995, it was replaced by the IBM PC Series 300.
The Epson Equity series of IBM Compatible Personal Computers was manufactured from 1985 until the early '90s by Epson Inc. Epson was well known for its dot matrix printers at the time and the Equity series represents their entry into the growing PC compatible market. The Equity I was the first system introduced, equipped with an Intel 8088 CPU and one or two 5.25" floppy disk drives.
The Commodore PC compatible systems are a range of IBM PC compatible personal computers introduced in 1984 by home computer manufacturer Commodore Business Machines.
The history of laptops describes the efforts, begun in 1970, to build small, portable personal computers that combine the components, inputs, outputs and capabilities of a desktop computer in a small chassis.
The PS/2E or Energy is a member of the IBM Personal System/2 family of personal computers (PCs). It was the first Energy Star-compliant PC, consuming very little power relative to other contemporary PCs, and made extensive use of recycled materials in its enclosure.
The Personal System/55 (パーソナルシステム/55) or PS/55 is a personal computer series released from IBM Japan in 1987.
The Tandy 3000 is a personal computer introduced by Radio Shack in 1986 based on the 16-bit 8 MHz Intel 80286 microprocessor.
The P75 was a Micro Channel architecture based, portable PS/2 computer released by IBM in 1990, and is noted as being the first portable computer using a 486 CPU to be available for sale in the United States. It had a briefcase-shaped design and ran off A/C power only, as was common with high performance portable computers at the time. It featured an Intel 80486 DX-33 CPU, and an internal 10 inch flat gas plasma display at 640x480 resolution with 16 shades of grey. The computer had relatively high performance specifications at the time it was released and could be used as a portable server. The cost reflected this performance; the IBM P75 retailed at US$15,990 for the base configuration, to over $18,500 or more depending on options.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
