Jones Cut

Last updated
Early construction on Jones Cut - March 23, 1909. Construction on Jones Cut in Blairstown NJ - March 23, 1909.jpg
Early construction on Jones Cut - March 23, 1909.
Blairstown Station, shown here in 1988, is located at the western end of Jones Cut. Blairstown-Station-1988.JPG
Blairstown Station, shown here in 1988, is located at the western end of Jones Cut.

Jones Cut is one of the cuts on the Lackawanna Cut-Off railroad line in northwest New Jersey.

Located near milepost 64.8 in Blairstown Township, the cut was constructed between 1908 and 1911 by contractor Hyde, McFarlan & Burke. Some 578,000 cubic yards (442,000 m3) of fill material was removed by blasting with dynamite or other methods. Jones Cut is located on a tangent (straight) section of track, permitting speeds of 80 mph (129 km/h). Blairstown Station sits within the cut. [1]

Jones Cut is named for William Jones, who was the principal owner of the land that was acquired for this cut. [2]

Related Research Articles

<span class="mw-page-title-main">Lackawanna Cut-Off</span> U.S. railway line between Port Morris, New Jersey, and Slateford, Pennsylvania

The Lackawanna Cut-Off was a rail line built by the Delaware, Lackawanna and Western Railroad (DL&W). Constructed from 1908 to 1911, the line was part of a 396-mile (637 km) main line between Hoboken, New Jersey, and Buffalo, New York. It ran west for 28.45 miles (45.79 km) from Port Morris Junction in Port Morris, New Jersey, near the south end of Lake Hopatcong about 45 miles (72 km) west-northwest of New York City, to Slateford Junction in Slateford, Pennsylvania near the Delaware Water Gap.

<span class="mw-page-title-main">Roseville Avenue station</span> Former NJ Transit rail station

Roseville Avenue was a transfer station on New Jersey Transit's Morris & Essex Lines in Newark, New Jersey, United States. The station was built by the Delaware, Lackawanna and Western Railroad in 1903 as part of a project to lower the tracks below the road surface to eliminate grade crossings. It serviced Newark's Roseville neighborhood. It once had two tracks on the Lackawanna mainline and two low-wall platforms, with an additional platform along the Montclair Branch. The station remained in service during most of the 20th century, until New Jersey Transit closed the station on September 16, 1984.

<span class="mw-page-title-main">Paulinskill Viaduct</span> Bridge in Hainesburg, New Jersey

The Paulinskill Viaduct, also known as the Hainesburg Viaduct, is a reinforced concrete railroad bridge that crosses the Paulins Kill in Knowlton Township, New Jersey. When completed in 1910, it was the largest reinforced concrete structure in the world.

William Haynes Truesdale (1851–1935) was an American railroad executive. He served as the president of the Delaware, Lackawanna and Western Railroad (DL&W) from 1899 to 1925.

The Boonton Branch refers to the railroad line in New Jersey that was completed in 1870 and ran 34 miles (54.8 km) from Hoboken to East Dover Junction as part of the Morris & Essex Railroad (M&E). Although the branch hosted commuter trains, the line was primarily built as a freight bypass line. The term "branch", therefore, is somewhat of a misnomer since the Boonton Branch was built to higher mainline standards than the Morristown Line, the line that it bypassed. As a result, the Boonton Branch better meets the definition of a "cut-off" rather than a branch. Some of the towns that the Boonton Branch passed through included Lyndhurst, Passaic, Clifton, Paterson, Wayne, Lincoln Park, Mountain Lakes, and its namesake, Boonton.

<span class="mw-page-title-main">Slateford Junction</span> Railroad junction in New Jersey

Slateford Junction was a railway junction in the small town of Slateford, Pennsylvania, that operated from 1911 to 1979.

<span class="mw-page-title-main">Port Morris Junction</span>

Port Morris Junction is the railroad connection between NJ Transit's Montclair-Boonton Line and the Lackawanna Cut-Off. Opened in 1911 by the Lackawanna Railroad, it is in the Port Morris, New Jersey section of Roxbury Township, New Jersey, south of Lake Hopatcong.

Timothy Burke was a businessman who, with his brother John M. Burke, founded the Burke Brothers Construction Company in Scranton, Pennsylvania, and the Scranton, Dunmore, and Moosic Lake Railroad.

<span class="mw-page-title-main">McMickle Cut (Lackawanna Cut-Off)</span> Open cut in New Jersey, US

McMickle Cut is the longest cut on the Lackawanna Cut-Off railroad line in northwest New Jersey. It was built between 1908 and 1911 by contractor Timothy Burke between mileposts 47.1 and 48.1 where Stanhope and Byram Township meet. Some 600,000 cubic yards of material was removed by dynamite and other methods to make the cut, which is 1.04 miles long, has an average depth of 29 feet, and a maximum depth of 54 feet.

<span class="mw-page-title-main">Waltz & Reece Cut</span> Open cut in New Jersey, US

Waltz & Reece Cut is the deepest cut on the Lackawanna Cut-Off railroad line in northwest New Jersey. The cut is 0.68 miles (1.09 km) long, has an average depth of 37 feet (11 m), and a maximum depth of 114 feet (35 m).

<span class="mw-page-title-main">Bradbury Fill</span> Embankment in New Jersey, US

Bradbury Fill is one of the embankments on the Lackawanna Cut-Off railroad line in northwest New Jersey. It was built from 1908 to 1911 by Waltz & Reece Construction Company. It sits between mileposts 49.1 and 49.8 in Byram Township, just west of Waltz & Reece Cut and east of Lubber Run Fill.

<span class="mw-page-title-main">Lubber Run Fill</span> Embankment in New Jersey, US

Lubber Run Fill is a fill on the Lackawanna Cut-Off railroad line in northwest New Jersey. Located between mileposts 50.1 and 50.5 in Byram Township, it was built between 1908 and 1911 by contractor Waltz & Reece Construction Company. It is 0.40 miles (0.64 km) long, has an average height of 64 feet, and a maximum height of 98 feet. Most of its 720,000 cubic yards (550500 m3) of fill material was excavated from the surrounding low-lying area.

<span class="mw-page-title-main">Wharton Fill</span> Embankment in New Jersey, US

Wharton Fill is one of a number of fills (embankments) on the Lackawanna Cut-Off railroad line in northwest New Jersey. Located between mileposts 51.1 and 51.6 in Byram Township, the fill was constructed between 1908 and 1911 by contractor David W. Flickwir. The fill, which was created by placing fill material obtained by blasting with dynamite or other methods, is about 0.5 miles (0.64 km) long. Most of the material that was used to create Wharton Fill was excavated from the surrounding low-lying area through which Pumpkin Run runs; several of the borrow pits have since flooded and become ponds.

<span class="mw-page-title-main">Colby Cut</span> Open cut in New Jersey, US

Colby Cut is one of a number of cuts on the Lackawanna Cut-Off railroad line in northwest New Jersey. Located between approximately mileposts 51.8 and 52.3 in Byram Township, the cut was constructed between 1908 and 1911 by contractor David W. Flickwir. The cut, which was created by removing fill material obtained by blasting with dynamite or other methods, is 0.53 miles (0.85 km) long, has an average depth of 45 feet (14 m), and a maximum depth of 110 feet (34 m). The cut was the result of the removal of 462,342 cubic yards of fill material within this section.

<span class="mw-page-title-main">Greendell station</span>

Greendell is one of three original railway stations built by the Delaware, Lackawanna & Western Railroad (DL&W) along its Lackawanna Cut-Off line in northwestern New Jersey. The station, which still stands in Green Township at milepost 57.61 on the Cut-Off, began operations on December 23, 1911, one day before the line itself opened and the first revenue train arrived.

<span class="mw-page-title-main">Andover station (NJ Transit)</span>

Andover is a planned New Jersey Transit passenger railroad station in Andover Township, in Sussex County, New Jersey, United States, providing service on its Lackawanna Cut-Off line. The line remains under construction. The station will be built at a site on Andover's Roseville Road, about 1.1 miles (1.8 km) from U.S. Route 206 and about 0.9 miles (1.4 km) from County Route 517. On the rail line, it will be located about 7.3 miles (11.7 km) west of Port Morris Junction.

<span class="mw-page-title-main">Ramsey Fill</span> Embankment in New Jersey, US

Ramsey Fill is one of the fills (embankments) on the Lackawanna Cut-Off railroad line in northwest New Jersey. Located between miles 60.4 and 60.9 in Frelinghuysen Township, the fill was constructed between 1908 and 1911 by contractor Hyde, McFarlan & Burke. The .53-mile (0.85 km) fill has an average height of 21 feet, and a maximum height of 80 feet. It was created with 805,481 cubic yards (615,834 m3) of fill material obtained by blasting with dynamite or other methods.

<span class="mw-page-title-main">Armstrong Cut</span> Open cut in New Jersey, US

Armstrong Cut is one of the largest cuts on the Lackawanna Cut-Off railroad line in northwest New Jersey. Located between approximately mileposts 61.4 and 62.3 in Frelinghuysen Township, the cut was constructed between 1908 and 1911 by contractor Hyde, McFarlan & Burke. The cut, which was created by removing fill material obtained by blasting with dynamite or other methods, is 0.89 miles (1.43 km) long, has an average depth of 52 feet (16 m), and a maximum depth of 104 feet (32 m). The fill was created as a result of the removal of 852,000 cubic yards of fill material from this section of the right-of-way. Armstrong Cut is located on a tangent (straight) section of track, permitting 80 mph (130 km/h).

<span class="mw-page-title-main">Vail Fill</span> Embankment in New Jersey, US

Vail fill is one of the fills on the Lackawanna Cut-Off railroad line in northwest New Jersey. Located between approximately mileposts 65 and 65.3 in Blairstown Township, the fill was constructed between 1908 and 1911 by contractor Hyde, McFarlan & Burke. The fill, which was created by fill material obtained by blasting with dynamite or other methods, much of which was obtained from nearby Jones Cut, the fill is 0.32 miles (0.51 km) long, an average of 39 feet (12 m) high, and a maximum of 102 feet (31 m) tall. The fill contains a total of 293,500 cubic yards of material. Vail Fill is located on a 1° curved section of track, permitting 80 mph (130 km/h).

<span class="mw-page-title-main">Nicholson Cutoff</span> Rail line segment

The Nicholson Cutoff is a rail line segment of the Sunbury Line rail line and formerly a rail line segment of the Delaware, Lackawanna and Western Railroad main line and the Delaware and Hudson Railway South Line. The Nicholson Cutoff and the rest of the Sunbury Line is owned by Norfolk Southern Railway.

References

  1. Taber, Thomas Townsend; Taber, Thomas Townsend III (1980). The Delaware, Lackawanna & Western Railroad in the Twentieth Century 1, p. 35. Muncy, PA: Privately printed. ISBN   0-9603398-2-5.
  2. 1906 Survey Map of the Delaware Valley Cut-Off, September 1, 1906.