Microwave

Last updated

A telecommunications tower with a variety of dish antennas for microwave relay links on Frazier Peak, Ventura County, California. The apertures of the dishes are covered by plastic sheets (radomes) to keep out moisture. Frazier Peak, tower and Honda Element.jpg
A telecommunications tower with a variety of dish antennas for microwave relay links on Frazier Peak, Ventura County, California. The apertures of the dishes are covered by plastic sheets (radomes) to keep out moisture.
The atmospheric attenuation of microwaves and far infrared radiation in dry air with a precipitable water vapor level of 0.001 mm. The downward spikes in the graph correspond to frequencies at which microwaves are absorbed more strongly. This graph includes a range of frequencies from 0 to 1 THz; the microwaves are the subset in the range between 0.3 and 300 gigahertz. Atmospheric Microwave Transmittance at Mauna Kea (simulated).svg
The atmospheric attenuation of microwaves and far infrared radiation in dry air with a precipitable water vapor level of 0.001 mm. The downward spikes in the graph correspond to frequencies at which microwaves are absorbed more strongly. This graph includes a range of frequencies from 0 to 1 THz; the microwaves are the subset in the range between 0.3 and 300 gigahertz.

Microwaves are a form of electromagnetic radiation with wavelengths ranging from about one meter to one millimeter; with frequencies between 300 MHz (1 m) and 300 GHz (1 mm). [1] [2] [3] [4] [5] Different sources define different frequency ranges as microwaves; the above broad definition includes both UHF and EHF (millimeter wave) bands. A more common definition in radio engineering is the range between 1 and 100 GHz (wavelengths between 0.3 m and 3 mm). [2] In all cases, microwaves include the entire SHF band (3 to 30 GHz, or 10 to 1 cm) at minimum. Frequencies in the microwave range are often referred to by their IEEE radar band designations: S, C, X, Ku, K, or Ka band, or by similar NATO or EU designations.

Electromagnetic radiation form of energy emitted and absorbed by charged particles, which exhibits wave-like behavior as it travels through space

In physics, electromagnetic radiation refers to the waves of the electromagnetic field, propagating (radiating) through space, carrying electromagnetic radiant energy. It includes radio waves, microwaves, infrared, (visible) light, ultraviolet, X-rays, and gamma rays.

Wavelength spatial period of the wave—the distance over which the waves shape repeats, and thus the inverse of the spatial frequency

In physics, the wavelength is the spatial period of a periodic wave—the distance over which the wave's shape repeats. It is thus the inverse of the spatial frequency. Wavelength is usually determined by considering the distance between consecutive corresponding points of the same phase, such as crests, troughs, or zero crossings and is a characteristic of both traveling waves and standing waves, as well as other spatial wave patterns. Wavelength is commonly designated by the Greek letter lambda (λ). The term wavelength is also sometimes applied to modulated waves, and to the sinusoidal envelopes of modulated waves or waves formed by interference of several sinusoids.

Frequency is the number of occurrences of a repeating event per unit of time. It is also referred to as temporal frequency, which emphasizes the contrast to spatial frequency and angular frequency. The period is the duration of time of one cycle in a repeating event, so the period is the reciprocal of the frequency. For example: if a newborn baby's heart beats at a frequency of 120 times a minute, its period—the time interval between beats—is half a second. Frequency is an important parameter used in science and engineering to specify the rate of oscillatory and vibratory phenomena, such as mechanical vibrations, audio signals (sound), radio waves, and light.

Contents

The prefix micro- in microwave is not meant to suggest a wavelength in the micrometer range. Rather, it indicates that microwaves are "small" (having shorter wavelengths), compared to the radio waves used prior to microwave technology. The boundaries between far infrared, terahertz radiation, microwaves, and ultra-high-frequency radio waves are fairly arbitrary and are used variously between different fields of study.

A prefix is an affix which is placed before the stem of a word. Adding it to the beginning of one word changes it into another word. For example, when the prefix un- is added to the word happy, it creates the word unhappy. Particularly in the study of languages, a prefix is also called a preformative, because it alters the form of the words to which it is affixed.

Micrometre one millionth of a metre

The micrometre or micrometer, also commonly known by the previous name micron, is an SI derived unit of length equaling 1×10−6 metre ; that is, one millionth of a metre.

Radio wave type of electromagnetic radiation

Radio waves are a type of electromagnetic radiation with wavelengths in the electromagnetic spectrum longer than infrared light. Radio waves have frequencies as high as 300 gigahertz (GHz) to as low as 30 hertz (Hz). At 300 GHz, the corresponding wavelength is 1 mm, and at 30 Hz is 10,000 km. Like all other electromagnetic waves, radio waves travel at the speed of light. They are generated by electric charges undergoing acceleration, such as time varying electric currents. Naturally occurring radio waves are emitted by lightning and astronomical objects.

Microwaves travel by line-of-sight; unlike lower frequency radio waves they do not diffract around hills, follow the earth's surface as ground waves, or reflect from the ionosphere, so terrestrial microwave communication links are limited by the visual horizon to about 40 miles (64 km). At the high end of the band they are absorbed by gases in the atmosphere, limiting practical communication distances to around a kilometer. Microwaves are widely used in modern technology, for example in point-to-point communication links, wireless networks, microwave radio relay networks, radar, satellite and spacecraft communication, medical diathermy and cancer treatment, remote sensing, radio astronomy, particle accelerators, spectroscopy, industrial heating, collision avoidance systems, garage door openers and keyless entry systems, and for cooking food in microwave ovens.

Line-of-sight propagation characteristic of electromagnetic radiation or acoustic wave propagation which means waves which travel in a direct path from the source to the receiver

Line-of-sight propagation is a characteristic of electromagnetic radiation or acoustic wave propagation which means waves travel in a direct path from the source to the receiver. Electromagnetic transmission includes light emissions traveling in a straight line. The rays or waves may be diffracted, refracted, reflected, or absorbed by the atmosphere and obstructions with material and generally cannot travel over the horizon or behind obstacles.

Ionosphere The ionized part of Earths upper atmosphere

The ionosphere is the ionized part of Earth's upper atmosphere, from about 60 km (37 mi) to 1,000 km (620 mi) altitude, a region that includes the thermosphere and parts of the mesosphere and exosphere. The ionosphere is ionized by solar radiation. It plays an important role in atmospheric electricity and forms the inner edge of the magnetosphere. It has practical importance because, among other functions, it influences radio propagation to distant places on the Earth.

In telecommunications, a point-to-point connection refers to a communications connection between two communication endpoints or nodes. An example is a telephone call, in which one telephone is connected with one other, and what is said by one caller can only be heard by the other. This is contrasted with a point-to-multipoint or broadcast connection, in which many nodes can receive information transmitted by one node. Other examples of point-to-point communications links are leased lines, microwave radio relay and two-way radio.

Electromagnetic spectrum

Microwaves occupy a place in the electromagnetic spectrum with frequency above ordinary radio waves, and below infrared light:

The electromagnetic spectrum is the range of frequencies of electromagnetic radiation and their respective wavelengths and photon energies.

Infrared electromagnetic radiation with longer wavelengths than those of visible light

Infrared radiation (IR), sometimes called infrared light, is electromagnetic radiation (EMR) with longer wavelengths than those of visible light, and is therefore generally invisible to the human eye, although IR at wavelengths up to 1050 nanometers (nm)s from specially pulsed lasers can be seen by humans under certain conditions. IR wavelengths extend from the nominal red edge of the visible spectrum at 700 nanometers, to 1 millimeter (300 GHz). Most of the thermal radiation emitted by objects near room temperature is infrared. As with all EMR, IR carries radiant energy and behaves both like a wave and like its quantum particle, the photon.

Electromagnetic spectrum
NameWavelength Frequency (Hz) Photon energy (eV)
Gamma ray < 0.02 nm> 15 EHz> 62.1 keV
X-ray 0.01 nm – 10 nm30 EHz – 30 PHz124 keV – 124 eV
Ultraviolet 10 nm – 400 nm30 PHz – 750 THz124 eV – 3 eV
Visible light 390 nm – 750 nm770 THz – 400 THz3.2 eV – 1.7 eV
Infrared 750 nm – 1 mm400 THz – 300 GHz1.7 eV – 1.24 meV
Microwave1 mm – 1 m300 GHz – 300 MHz1.24 meV – 1.24 µeV
Radio 1 mm – 100 km 300 GHz3 kHz 1.24 µeV – 12.4 feV

In descriptions of the electromagnetic spectrum, some sources classify microwaves as radio waves, a subset of the radio wave band; while others classify microwaves and radio waves as distinct types of radiation. This is an arbitrary distinction.

Propagation

Microwaves travel solely by line-of-sight paths; unlike lower frequency radio waves, they do not travel as ground waves which follow the contour of the Earth, or reflect off the ionosphere (skywaves). [6] Although at the low end of the band they can pass through building walls enough for useful reception, usually rights of way cleared to the first Fresnel zone are required. Therefore, on the surface of the Earth, microwave communication links are limited by the visual horizon to about 30–40 miles (48–64 km). Microwaves are absorbed by moisture in the atmosphere, and the attenuation increases with frequency, becoming a significant factor (rain fade) at the high end of the band. Beginning at about 40 GHz, atmospheric gases also begin to absorb microwaves, so above this frequency microwave transmission is limited to a few kilometers. A spectral band structure causes absorption peaks at specific frequencies (see graph at right). Above 100 GHz, the absorption of electromagnetic radiation by Earth's atmosphere is so great that it is in effect opaque, until the atmosphere becomes transparent again in the so-called infrared and optical window frequency ranges.

Skywave an electrically charged layer of the upper atmosphere

In radio communication, skywave or skip refers to the propagation of radio waves reflected or refracted back toward Earth from the ionosphere, an electrically charged layer of the upper atmosphere. Since it is not limited by the curvature of the Earth, skywave propagation can be used to communicate beyond the horizon, at intercontinental distances. It is mostly used in the shortwave frequency bands.

Fresnel zone region of space between a transmitting and receiving antenna

A Fresnel zone, named after physicist Augustin-Jean Fresnel, is one of a series of confocal prolate ellipsoidal regions of space between and around a transmitting antenna and a receiving antenna system. The regions are used to understand and compute the strength of waves propagating between a transmitter and a receiver, as well as predict whether obstructions near the line joining the transmitter and receiver will cause significant interference.

Rain fade refers primarily to the absorption of a microwave radio frequency (RF) signal by atmospheric rain, snow, or ice, and losses which are especially prevalent at frequencies above 11 GHz. It also refers to the degradation of a signal caused by the electromagnetic interference of the leading edge of a storm front. Rain fade can be caused by precipitation at the uplink or downlink location. However, it does not need to be raining at a location for it to be affected by rain fade, as the signal may pass through precipitation many miles away, especially if the satellite dish has a low look angle. From 5 to 20 percent of rain fade or satellite signal attenuation may also be caused by rain, snow, or ice on the uplink or downlink antenna reflector, radome or feed horn. Rain fade is not limited to satellite uplinks or downlinks, it also can affect terrestrial point to point microwave links.

Troposcatter

In a microwave beam directed at an angle into the sky, a small amount of the power will be randomly scattered as the beam passes through the troposphere. [6] A sensitive receiver beyond the horizon with a high gain antenna focused on that area of the troposphere can pick up the signal. This technique has been used at frequencies between 0.45 and 5 GHz in tropospheric scatter (troposcatter) communication systems to communicate beyond the horizon, at distances up to 300 km.

Antennas

Waveguide is used to carry microwaves. Example of waveguides and a diplexer in an air traffic control radar Diplexer1.jpg
Waveguide is used to carry microwaves. Example of waveguides and a diplexer in an air traffic control radar

The short wavelengths of microwaves allow omnidirectional antennas for portable devices to be made very small, from 1 to 20 centimeters long, so microwave frequencies are widely used for wireless devices such as cell phones, cordless phones, and wireless LANs (Wi-Fi) access for laptops, and Bluetooth earphones. Antennas used include short whip antennas, rubber ducky antennas, sleeve dipoles, patch antennas, and increasingly the printed circuit inverted F antenna (PIFA) used in cell phones.

Their short wavelength also allows narrow beams of microwaves to be produced by conveniently small high gain antennas from a half meter to 5 meters in diameter. Therefore, beams of microwaves are used for point-to-point communication links, and for radar. An advantage of narrow beams is that they don't interfere with nearby equipment using the same frequency, allowing frequency reuse by nearby transmitters. Parabolic ("dish") antennas are the most widely used directive antennas at microwave frequencies, but horn antennas, slot antennas and dielectric lens antennas are also used. Flat microstrip antennas are being increasingly used in consumer devices. Another directive antenna practical at microwave frequencies is the phased array, a computer-controlled array of antennas which produces a beam which can be electronically steered in different directions.

At microwave frequencies, the transmission lines which are used to carry lower frequency radio waves to and from antennas, such as coaxial cable and parallel wire lines, have excessive power losses, so when low attenuation is required microwaves are carried by metal pipes called waveguides. Due to the high cost and maintenance requirements of waveguide runs, in many microwave antennas the output stage of the transmitter or the RF front end of the receiver is located at the antenna.

Design and analysis

The term microwave also has a more technical meaning in electromagnetics and circuit theory. [7] Apparatus and techniques may be described qualitatively as "microwave" when the wavelengths of signals are roughly the same as the dimensions of the circuit, so that lumped-element circuit theory is inaccurate, and instead distributed circuit elements and transmission-line theory are more useful methods for design and analysis.

As a consequence, practical microwave circuits tend to move away from the discrete resistors, capacitors, and inductors used with lower-frequency radio waves. Open-wire and coaxial transmission lines used at lower frequencies are replaced by waveguides and stripline, and lumped-element tuned circuits are replaced by cavity resonators or resonant stubs. [7] In turn, at even higher frequencies, where the wavelength of the electromagnetic waves becomes small in comparison to the size of the structures used to process them, microwave techniques become inadequate, and the methods of optics are used.

Microwave sources

Magnetron section transverse to axis.JPG
Antennenw1.jpg
Cutaway view inside a cavity magnetron as used in a microwave oven (left). Antenna splitter: microstrip techniques become increasingly necessary at higher frequencies (right).
Disassembled radar speed gun. The grey assembly attached to the end of the copper-colored horn antenna is the Gunn diode which generates the microwaves. Radar speed gun internal works.jpg
Disassembled radar speed gun. The grey assembly attached to the end of the copper-colored horn antenna is the Gunn diode which generates the microwaves.

High-power microwave sources use specialized vacuum tubes to generate microwaves. These devices operate on different principles from low-frequency vacuum tubes, using the ballistic motion of electrons in a vacuum under the influence of controlling electric or magnetic fields, and include the magnetron (used in microwave ovens), klystron, traveling-wave tube (TWT), and gyrotron. These devices work in the density modulated mode, rather than the current modulated mode. This means that they work on the basis of clumps of electrons flying ballistically through them, rather than using a continuous stream of electrons.

Low-power microwave sources use solid-state devices such as the field-effect transistor (at least at lower frequencies), tunnel diodes, Gunn diodes, and IMPATT diodes. [8] Low-power sources are available as benchtop instruments, rackmount instruments, embeddable modules and in card-level formats. A maser is a solid state device which amplifies microwaves using similar principles to the laser, which amplifies higher frequency light waves.

All warm objects emit low level microwave black-body radiation, depending on their temperature, so in meteorology and remote sensing microwave radiometers are used to measure the temperature of objects or terrain. [9] The sun [10] and other astronomical radio sources such as Cassiopeia A emit low level microwave radiation which carries information about their makeup, which is studied by radio astronomers using receivers called radio telescopes. [9] The cosmic microwave background radiation (CMBR), for example, is a weak microwave noise filling empty space which is a major source of information on cosmology's Big Bang theory of the origin of the Universe.

Microwave uses

Microwave technology is extensively used for point-to-point telecommunications (i.e. non-broadcast uses). Microwaves are especially suitable for this use since they are more easily focused into narrower beams than radio waves, allowing frequency reuse; their comparatively higher frequencies allow broad bandwidth and high data transmission rates, and antenna sizes are smaller than at lower frequencies because antenna size is inversely proportional to transmitted frequency. Microwaves are used in spacecraft communication, and much of the world's data, TV, and telephone communications are transmitted long distances by microwaves between ground stations and communications satellites. Microwaves are also employed in microwave ovens and in radar technology.

Communication

A satellite dish on a residence, which receives satellite television over a Ku band 12-14 GHz microwave beam from a direct broadcast communications satellite in a geostationary orbit 35,700 kilometres (22,000 miles) above the Earth SuperDISH121.jpg
A satellite dish on a residence, which receives satellite television over a Ku band 12–14 GHz microwave beam from a direct broadcast communications satellite in a geostationary orbit 35,700 kilometres (22,000 miles) above the Earth

Before the advent of fiber-optic transmission, most long-distance telephone calls were carried via networks of microwave radio relay links run by carriers such as AT&T Long Lines. Starting in the early 1950s, frequency division multiplex was used to send up to 5,400 telephone channels on each microwave radio channel, with as many as ten radio channels combined into one antenna for the hop to the next site, up to 70 km away.

Wireless LAN protocols, such as Bluetooth and the IEEE 802.11 specifications used for Wi-Fi, also use microwaves in the 2.4 GHz ISM band, although 802.11a uses ISM band and U-NII frequencies in the 5 GHz range. Licensed long-range (up to about 25 km) Wireless Internet Access services have been used for almost a decade in many countries in the 3.5–4.0 GHz range. The FCC recently[ when? ] carved out spectrum for carriers that wish to offer services in this range in the U.S. — with emphasis on 3.65 GHz. Dozens of service providers across the country are securing or have already received licenses from the FCC to operate in this band. The WIMAX service offerings that can be carried on the 3.65 GHz band will give business customers another option for connectivity.

Metropolitan area network (MAN) protocols, such as WiMAX (Worldwide Interoperability for Microwave Access) are based on standards such as IEEE 802.16, designed to operate between 2 and 11 GHz. Commercial implementations are in the 2.3 GHz, 2.5 GHz, 3.5 GHz and 5.8 GHz ranges.

Mobile Broadband Wireless Access (MBWA) protocols based on standards specifications such as IEEE 802.20 or ATIS/ANSI HC-SDMA (such as iBurst) operate between 1.6 and 2.3 GHz to give mobility and in-building penetration characteristics similar to mobile phones but with vastly greater spectral efficiency. [11]

Some mobile phone networks, like GSM, use the low-microwave/high-UHF frequencies around 1.8 and 1.9 GHz in the Americas and elsewhere, respectively. DVB-SH and S-DMB use 1.452 to 1.492 GHz, while proprietary/incompatible satellite radio in the U.S. uses around 2.3 GHz for DARS.

Microwave radio is used in broadcasting and telecommunication transmissions because, due to their short wavelength, highly directional antennas are smaller and therefore more practical than they would be at longer wavelengths (lower frequencies). There is also more bandwidth in the microwave spectrum than in the rest of the radio spectrum; the usable bandwidth below 300 MHz is less than 300 MHz while many GHz can be used above 300 MHz. Typically, microwaves are used in television news to transmit a signal from a remote location to a television station from a specially equipped van. See broadcast auxiliary service (BAS), remote pickup unit (RPU), and studio/transmitter link (STL).

Most satellite communications systems operate in the C, X, Ka, or Ku bands of the microwave spectrum. These frequencies allow large bandwidth while avoiding the crowded UHF frequencies and staying below the atmospheric absorption of EHF frequencies. Satellite TV either operates in the C band for the traditional large dish fixed satellite service or Ku band for direct-broadcast satellite. Military communications run primarily over X or Ku-band links, with Ka band being used for Milstar.

Global Navigation Satellite Systems (GNSS) including the Chinese Beidou, the American Global Positioning System (introduced in 1978) and the Russian GLONASS broadcast navigational signals in various bands between about 1.2 GHz and 1.6 GHz.

Radar

The parabolic antenna (lower curved surface) of an ASR-9 airport surveillance radar which radiates a narrow vertical fan-shaped beam of 2.7-2.9 GHz (S band) microwaves to locate aircraft in the airspace surrounding an airport. ASR-9 Radar Antenna.jpg
The parabolic antenna (lower curved surface) of an ASR-9 airport surveillance radar which radiates a narrow vertical fan-shaped beam of 2.7–2.9 GHz (S band) microwaves to locate aircraft in the airspace surrounding an airport.

Radar is a radiolocation technique in which a beam of radio waves emitted by a transmitter bounces off an object and returns to a receiver, allowing the location, range, speed, and other characteristics of the object to be determined. The short wavelength of microwaves causes large reflections from objects the size of motor vehicles, ships and aircraft. Also, at these wavelengths, the high gain antennas such as parabolic antennas which are required to produce the narrow beamwidths needed to accurately locate objects are conveniently small, allowing them to be rapidly turned to scan for objects. Therefore, microwave frequencies are the main frequencies used in radar. Microwave radar is widely used for applications such as air traffic control, weather forecasting, navigation of ships, and speed limit enforcement. Long distance radars use the lower microwave frequencies since at the upper end of the band atmospheric absorption limits the range, but millimeter waves are used for short range radar such as collision avoidance systems.

The Atacama Compact Array.jpg
Some of the dish antennas of the Atacama Large Millimeter Array (ALMA) a radio telescope located in northern Chile. It receives microwaves in the millimeter wave range, 31 – 1000 GHz.
BigBangNoise.jpg
Maps of the cosmic microwave background radiation (CMBR), showing the improved resolution which has been achieved with better microwave radio telescopes

Radio astronomy

Microwaves emitted by astronomical radio sources; planets, stars, galaxies, and nebulas are studied in radio astronomy with large dish antennas called radio telescopes. In addition to receiving naturally occurring microwave radiation, radio telescopes have been used in active radar experiments to bounce microwaves off planets in the solar system, to determine the distance to the Moon or map the invisible surface of Venus through cloud cover.

A recently completed microwave radio telescope is the Atacama Large Millimeter Array, located at more than 5,000 meters (16,597 ft) altitude in Chile, observes the universe in the millimetre and submillimetre wavelength ranges. The world's largest ground-based astronomy project to date, it consists of more than 66 dishes and was built in an international collaboration by Europe, North America, East Asia and Chile. [12] [13]

A major recent focus of microwave radio astronomy has been mapping the cosmic microwave background radiation (CMBR) discovered in 1964 by radio astronomers Arno Penzias and Robert Wilson. This faint background radiation, which fills the universe and is almost the same in all directions, is "relic radiation" from the Big Bang, and is one of the few sources of information about conditions in the early universe. Due to the expansion and thus cooling of the Universe, the originally high-energy radiation has been shifted into the microwave region of the radio spectrum. Sufficiently sensitive radio telescopes can detected the CMBR as a faint signal that is not associated with any star, galaxy, or other object. [14]

Heating and power application

Small microwave oven on a kitchen counter Electrodomesticos de linea blanca 18.JPG
Small microwave oven on a kitchen counter
Microwaves are widely used for heating in industrial processes. A microwave tunnel oven for softening plastic rods prior to extrusion. Microwave tunnel closeup.jpg
Microwaves are widely used for heating in industrial processes. A microwave tunnel oven for softening plastic rods prior to extrusion.

A microwave oven passes microwave radiation at a frequency near 2.45 GHz (12 cm) through food, causing dielectric heating primarily by absorption of the energy in water. Microwave ovens became common kitchen appliances in Western countries in the late 1970s, following the development of less expensive cavity magnetrons. Water in the liquid state possesses many molecular interactions that broaden the absorption peak. In the vapor phase, isolated water molecules absorb at around 22 GHz, almost ten times the frequency of the microwave oven.

Microwave heating is used in industrial processes for drying and curing products.

Many semiconductor processing techniques use microwaves to generate plasma for such purposes as reactive ion etching and plasma-enhanced chemical vapor deposition (PECVD).

Microwave frequencies typically ranging from 110 – 140 GHz are used in stellarators and tokamak experimental fusion reactors to help heat the fuel into a plasma state. The upcoming ITER thermonuclear reactor [15] is expected to range from 110–170 GHz and will employ electron cyclotron resonance heating (ECRH). [16]

Microwaves can be used to transmit power over long distances, and post-World War II research was done to examine possibilities. NASA worked in the 1970s and early 1980s to research the possibilities of using solar power satellite (SPS) systems with large solar arrays that would beam power down to the Earth's surface via microwaves.

Less-than-lethal weaponry exists that uses millimeter waves to heat a thin layer of human skin to an intolerable temperature so as to make the targeted person move away. A two-second burst of the 95 GHz focused beam heats the skin to a temperature of 54 °C (129 °F) at a depth of 0.4 millimetres (164 in). The United States Air Force and Marines are currently using this type of active denial system in fixed installations. [17]

Spectroscopy

Microwave radiation is used in electron paramagnetic resonance (EPR or ESR) spectroscopy, typically in the X-band region (~9 GHz) in conjunction typically with magnetic fields of 0.3 T. This technique provides information on unpaired electrons in chemical systems, such as free radicals or transition metal ions such as Cu(II). Microwave radiation is also used to perform rotational spectroscopy and can be combined with electrochemistry as in microwave enhanced electrochemistry.

Microwave frequency bands

Rough plot of Earth's atmospheric transmittance (or opacity) to various wavelengths of electromagnetic radiation. Microwaves are strongly absorbed at wavelengths shorter than about 1.5 cm (above 20 GHz) by water and other molecules in the air. Atmospheric electromagnetic opacity.svg
Rough plot of Earth's atmospheric transmittance (or opacity) to various wavelengths of electromagnetic radiation. Microwaves are strongly absorbed at wavelengths shorter than about 1.5 cm (above 20 GHz) by water and other molecules in the air.

Bands of frequencies in the microwave spectrum are designated by letters. Unfortunately, there are several incompatible band designation systems, and even within a system the frequency ranges corresponding to some of the letters vary somewhat between different application fields. [18] [19] The letter system had its origin in World War 2 in a top secret U.S. classification of bands used in radar sets; this is the origin of the oldest letter system, the IEEE radar bands. One set of microwave frequency bands designations by the Radio Society of Great Britain (RSGB), is tabulated below:

Microwave frequency bands
DesignationFrequency rangeWavelength rangeTypical uses
L band 1 to 2 GHz15 cm to 30 cmmilitary telemetry, GPS, mobile phones (GSM), amateur radio
S band 2 to 4 GHz7.5 cm to 15 cmweather radar, surface ship radar, and some communications satellites (microwave ovens, microwave devices/communications, radio astronomy, mobile phones, wireless LAN, Bluetooth, ZigBee, GPS, amateur radio)
C band 4 to 8 GHz3.75 cm to 7.5 cmlong-distance radio telecommunications
X band 8 to 12 GHz25 mm to 37.5 mmsatellite communications, radar, terrestrial broadband, space communications, amateur radio, molecular rotational spectroscopy
Ku band 12 to 18 GHz16.7 mm to 25 mmsatellite communications, molecular rotational spectroscopy
K band 18 to 26.5 GHz11.3 mm to 16.7 mmradar, satellite communications, astronomical observations, automotive radar, molecular rotational spectroscopy
Ka band 26.5 to 40 GHz5.0 mm to 11.3 mmsatellite communications, molecular rotational spectroscopy
Q band 33 to 50 GHz6.0 mm to 9.0 mmsatellite communications, terrestrial microwave communications, radio astronomy, automotive radar, molecular rotational spectroscopy
U band 40 to 60 GHz5.0 mm to 7.5 mm
V band 50 to 75 GHz4.0 mm to 6.0 mmmillimeter wave radar research, molecular rotational spectroscopy and other kinds of scientific research
W band 75 to 110 GHz2.7 mm to 4.0 mmsatellite communications, millimeter-wave radar research, military radar targeting and tracking applications, and some non-military applications, automotive radar
F band 90 to 140 GHz2.1 mm to 3.3 mmSHF transmissions: Radio astronomy, microwave devices/communications, wireless LAN, most modern radars, communications satellites, satellite television broadcasting, DBS, amateur radio
D band 110 to 170 GHz1.8 mm to 2.7 mmEHF transmissions: Radio astronomy, high-frequency microwave radio relay, microwave remote sensing, amateur radio, directed-energy weapon, millimeter wave scanner

P band is sometimes used for Ku Band. "P" for "previous" was a radar band used in the UK ranging from 250 to 500 MHz and now obsolete per IEEE Std 521. [20] [21] [22]

When radars were first developed at K band during World War II, it was not known that there was a nearby absorption band (due to water vapor and oxygen in the atmosphere). To avoid this problem, the original K band was split into a lower band, Ku, and upper band, Ka. [23]

Microwave frequency measurement

Absorption wavemeter for measuring in the Ku band. Ondamtr.JPG
Absorption wavemeter for measuring in the Ku band.

Microwave frequency can be measured by either electronic or mechanical techniques.

Frequency counters or high frequency heterodyne systems can be used. Here the unknown frequency is compared with harmonics of a known lower frequency by use of a low frequency generator, a harmonic generator and a mixer. Accuracy of the measurement is limited by the accuracy and stability of the reference source.

Mechanical methods require a tunable resonator such as an absorption wavemeter, which has a known relation between a physical dimension and frequency.

In a laboratory setting, Lecher lines can be used to directly measure the wavelength on a transmission line made of parallel wires, the frequency can then be calculated. A similar technique is to use a slotted waveguide or slotted coaxial line to directly measure the wavelength. These devices consist of a probe introduced into the line through a longitudinal slot, so that the probe is free to travel up and down the line. Slotted lines are primarily intended for measurement of the voltage standing wave ratio on the line. However, provided a standing wave is present, they may also be used to measure the distance between the nodes, which is equal to half the wavelength. Precision of this method is limited by the determination of the nodal locations.

Effects on health

Microwaves do not contain sufficient energy to chemically change substances by ionization, and so are an example of non-ionizing radiation. [24] The word "radiation" refers to energy radiating from a source and not to radioactivity. It has not been shown conclusively that microwaves (or other non-ionizing electromagnetic radiation) have significant adverse biological effects at low levels. Some, but not all, studies suggest that long-term exposure may have a carcinogenic effect. [25] This is separate from the risks associated with very high-intensity exposure, which can cause heating and burns like any heat source, and not a unique property of microwaves specifically.

During World War II, it was observed that individuals in the radiation path of radar installations experienced clicks and buzzing sounds in response to microwave radiation. This microwave auditory effect was thought to be caused by the microwaves inducing an electric current in the hearing centers of the brain. [26] Research by NASA in the 1970s has shown this to be caused by thermal expansion in parts of the inner ear. In 1955 Dr. James Lovelock was able to reanimate rats chilled to 0-1°C using microwave diathermy. [27]

When injury from exposure to microwaves occurs, it usually results from dielectric heating induced in the body. Exposure to microwave radiation can produce cataracts by this mechanism, [28] because the microwave heating denatures proteins in the crystalline lens of the eye (in the same way that heat turns egg whites white and opaque). The lens and cornea of the eye are especially vulnerable because they contain no blood vessels that can carry away heat. Exposure to heavy doses of microwave radiation (as from an oven that has been tampered with to allow operation even with the door open) can produce heat damage in other tissues as well, up to and including serious burns that may not be immediately evident because of the tendency for microwaves to heat deeper tissues with higher moisture content.

Eleanor R. Adair conducted microwave health research by exposing herself, animals and humans to microwave levels that made them feel warm or even start to sweat and feel quite uncomfortable. She found no adverse health effects other than heat.

History

Hertzian optics

Microwaves were first generated in the 1880s and 1890s in some of the earliest radio experiments by physicists who thought of them as a form of "invisible light". [29] James Clerk Maxwell in his 1873 theory of electromagnetism, now called Maxwell's equations, had predicted the existence of electromagnetic waves and proposed that light was composed of these waves. In 1888, German physicist Heinrich Hertz was the first to demonstrate the existence of radio waves using a primitive spark gap radio transmitter. [30] Hertz and the other early radio researchers were interested in exploring the similarities between radio waves and light waves, to test Maxwell's theory. They concentrated on producing short wavelength radio waves in the UHF and microwave ranges, with which they could duplicate classic optics experiments, using quasioptical components such as prisms and lenses made of paraffin, sulfur and pitch and wire diffraction gratings, to refract and diffract radio waves like light rays. [31] Hertz produced waves up to 450 MHz; his directional 450 MHz transmitter consisted of a 26 cm brass rod dipole antenna with a spark gap between the ends suspended at the focal line of a parabolic antenna made of a curved zinc sheet, powered by high voltage pulses from an induction coil. [30] His historic experiments demonstrated that radio waves like light exhibited refraction, diffraction, polarization, interference and standing waves, [31] proving that radio waves and light waves were both forms of Maxwell's electromagnetic waves.

In 1894, Oliver Lodge and Augusto Righi generated 1.5 and 12 GHz microwaves respectively with small metal ball spark resonators. [31] The same year Indian physicist Jagadish Chandra Bose was the first person to produce millimeter waves, generating 60 GHz (5 millimeter) microwaves using a 3 mm metal ball spark oscillator. [32] [31] Bose also invented waveguide and horn antennas for use in his experiments. Russian physicist Pyotr Lebedev in 1895 generated 50 GHz millimeter waves. [31] In 1897 Lord Rayleigh solved the mathematical boundary-value problem of electromagnetic waves propagating through conducting tubes and dielectric rods of arbitrary shape. [33] [34] [35] [36] which gave the modes and cutoff frequency of microwaves propagating through a waveguide. [30]

However, since microwaves were limited to line of sight paths, they could not communicate beyond the visual horizon, and the low power of the spark transmitters then in use limited their practical range to a few miles. The subsequent development of radio communication after 1896 employed lower frequencies, which could travel beyond the horizon as ground waves and by reflecting off the ionosphere as skywaves, and microwave frequencies were not further explored at this time.

First microwave communication experiments

Practical use of microwave frequencies did not occur until the 1940s and 1950s due to a lack of adequate sources, since the triode vacuum tube (valve) electronic oscillator used in radio transmitters could not produce frequencies above a few hundred megahertz due to excessive electron transit time and interelectrode capacitance. [30] By the 1930s, the first low power microwave vacuum tubes had been developed using new principles; the Barkhausen-Kurz tube and the split-anode magnetron. [30] These could generate a few watts of power at frequencies up to a few gigahertz, and were used in the first experiments in communication with microwaves.

In 1931 an Anglo-French consortium demonstrated the first experimental microwave relay link, across the English Channel 40 miles (64 km) between Dover, UK and Calais, France. [37] [38] The system transmitted telephony, telegraph and facsimile data over bidirectional 1.7 GHz beams with a power of one-half watt, produced by miniature Barkhausen-Kurz tubes at the focus of 10-foot (3 m) metal dishes.

A word was needed to distinguish these new shorter wavelengths, which had previously been lumped into the "short wave" band, which meant all waves shorter than 200 meters. The terms quasi-optical waves and ultrashort waves were used briefly, but didn't catch on. The first usage of the word microwave apparently occurred in 1931. [38] [39]

Radar

The development of radar, mainly in secrecy, before and during World War 2, resulted in the technological advances which made microwaves practical. [30] Radar antennas small enough to fit on aircraft which had a narrow enough beamwidth to localize enemy aircraft required wavelengths in the centimeter range. It was found that conventional transmission lines used to carry radio waves had excessive power losses at microwave frequencies, and George Southworth at Bell Labs and Wilmer Barrow at MIT independently invented waveguide in 1936. [33] Barrow invented the horn antenna in 1938 as a means to efficiently radiate microwaves into or out of a waveguide. In a microwave receiver, a nonlinear component was needed that would act as a detector and mixer at these frequencies, as vacuum tubes had too much capacitance. To fill this need researchers resurrected an obsolete technology, the point contact crystal detector (cat whisker detector) which was used as a demodulator in crystal radios around the turn of the century before vacuum tube receivers. [30] [40] The low capacitance of semiconductor junctions allowed them to function at microwave frequencies. The first modern silicon and germanium diodes were developed as microwave detectors in the 1930s, and the principles of semiconductor physics learned during their development led to semiconductor electronics after the war. [30]

The first powerful sources of microwaves were invented at the beginning of World War 2: the klystron tube by Russell and Sigurd Varian at Stanford University in 1937, and the cavity magnetron tube by John Randall and Harry Boot at Birmingham University, UK in 1940. [30] Britain's 1940 decision to share its microwave technology with the US (the Tizard Mission) significantly influenced the outcome of the war. The MIT Radiation Laboratory established secretly at Massachusetts Institute of Technology in 1940 to research radar, produced much of the theoretical knowledge necessary to use microwaves. By 1943, 10 centimeter (3 GHz) radar was in use on British and American warplanes. The first microwave relay systems were developed by the Allied military near the end of the war and used for secure battlefield communication networks in the European theater.

Post World War 2

After World War 2, microwaves were rapidly exploited commercially. [30] Due to their high frequency they had a very large information-carrying capacity (bandwidth); a single microwave beam could carry tens of thousands of phone calls. In the 1950s and 60s transcontinental microwave relay networks were built in the US and Europe to exchange telephone calls between cities and distribute television programs. In the new television broadcasting industry, from the 1940s microwave dishes were used to transmit backhaul video feed from mobile production trucks back to the studio, allowing the first remote TV broadcasts. The first communications satellites were launched in the 1960s, which relayed telephone calls and television between widely separated points on Earth using microwave beams. In 1964, Arno Penzias and Robert Woodrow Wilson while investigating noise in a satellite horn antenna at Bell Labs, Holmdel, New Jersey discovered cosmic microwave background radiation.

Hogg horn antennas.jpg
C-band horn antennas at a telephone switching center in Seattle, belonging to AT&T's Long Lines microwave relay network built in the 1960s.
NIKE AJAX Anti-Aircraft Missile Radar3.jpg
Microwave lens antenna used in the radar for the 1954 Nike Ajax anti-aircraft missile
NS Savannah microwave oven MD8.jpg
The first commercial microwave oven, Amana's Radarange, in kitchen of US aircraft carrier Savannah in 1961

Microwave radar became the central technology used in air traffic control, maritime navigation, anti-aircraft defense, ballistic missile detection, and later many other uses. Radar and satellite communication motivated the development of modern microwave antennas; the parabolic antenna (the most common type), cassegrain antenna, lens antenna, slot antenna, and phased array.

The ability of short waves to quickly heat materials and cook food had been investigated in the 1930s by I. F. Mouromtseff at Westinghouse, and at the 1933 Chicago World's Fair demonstrated cooking meals with a 60 MHz radio transmitter. [41] In 1945 Percy Spencer, an engineer working on radar at Raytheon, noticed that microwave radiation from a magnetron oscillator melted a candy bar in his pocket. He investigated cooking with microwaves and invented the microwave oven, consisting of a magnetron feeding microwaves into a closed metal cavity containing food, which was patented by Raytheon on 8 October 1945. Due to their expense microwave ovens were initially used in institutional kitchens, but by 1986 roughly 25% of households in the U.S. owned one. Microwave heating became widely used as an industrial process in industries such as plastics fabrication, and as a medical therapy to kill cancer cells in microwave hyperthermy.

The traveling wave tube (TWT) developed in 1943 by Rudolph Kompfner and John Pierce provided a high-power tunable source of microwaves up to 50 GHz, and became the most widely used microwave tube (besides the ubiquitous magnetron used in microwave ovens). The gyrotron tube family developed in Russia could produce megawatts of power up into millimeter wave frequencies, and is used in industrial heating and plasma research, and to power particle accelerators and nuclear fusion reactors.

Solid state microwave devices

Radar speed gun. At the right end of the copper horn antenna is the Gunn diode (grey assembly) which generates the microwaves. Radar Gun Electronics.jpg
Radar speed gun. At the right end of the copper horn antenna is the Gunn diode (grey assembly) which generates the microwaves.

The development of semiconductor electronics in the 1950s led to the first solid state microwave devices which worked by a new principle; negative resistance (some of the prewar microwave tubes had also used negative resistance). [30] The feedback oscillator and two-port amplifiers which were used at lower frequencies became unstable at microwave frequencies, and negative resistance oscillators and amplifiers based on one-port devices like diodes worked better.

The tunnel diode invented in 1957 by Japanese physicist Leo Esaki could produce a few milliwatts of microwave power. Its invention set off a search for better negative resistance semiconductor devices for use as microwave oscillators, resulting in the invention of the IMPATT diode in 1956 by W.T. Read and Ralph L. Johnston and the Gunn diode in 1962 by J. B. Gunn. [30] Diodes are the most widely used microwave sources today. Two low-noise solid state negative resistance microwave amplifiers were developed; the ruby maser invented in 1953 by Charles H. Townes, James P. Gordon, and H. J. Zeiger, and the varactor parametric amplifier developed in 1956 by Marion Hines. [30] These were used for low noise microwave receivers in radio telescopes and satellite ground stations. The maser led to the development of atomic clocks, which keep time using a precise microwave frequency emitted by atoms undergoing an electron transition between two energy levels. Negative resistance amplifier circuits required the invention of new nonreciprocal waveguide components, such as circulators, isolators, and directional couplers. In 1969 Kurokawa derived mathematical conditions for stability in negative resistance circuits which formed the basis of microwave oscillator design. [42]

Microwave integrated circuits

ku band microstrip circuit used in satellite television dish. LNB dissassembled.JPG
ku band microstrip circuit used in satellite television dish.

Prior to the 1970s microwave devices and circuits were bulky and expensive, so microwave frequencies were generally limited to the output stage of transmitters and the RF front end of receivers, and signals were heterodyned to a lower intermediate frequency for processing. The period from the 1970s to the present has seen the development of tiny inexpensive active solid state microwave components which can be mounted on circuit boards, allowing circuits to perform significant signal processing at microwave frequencies. This has made possible satellite television, cable television, GPS devices, and modern wireless devices, such as smartphones, Wi-Fi, and Bluetooth which connect to networks using microwaves.

Microstrip, a type of transmission line usable at microwave frequencies, was invented with printed circuits in the 1950s. [30] The ability to cheaply fabricate a wide range of shapes on printed circuit boards allowed microstrip versions of capacitors, inductors, resonant stubs, splitters, directional couplers, diplexers, filters and antennas to be made, thus allowing compact microwave circuits to be constructed. [30]

Transistors that operated at microwave frequencies were developed in the 1970s. The semiconductor gallium arsenide (GaAs) has a much higher electron mobility than silicon, [30] so devices fabricated with this material can operate at 4 times the frequency of similar devices of silicon. Beginning in the 1970s GaAs was used to make the first microwave transistors, [30] and it has dominated microwave semiconductors ever since. MESFETs (metal-semiconductor field-effect transistors), fast GaAs field effect transistors using Schottky junctions for the gate, were developed starting in 1968 and have reached cutoff frequencies of 100 GHz, and are now the most widely used active microwave devices. [30] Another family of transistors with a higher frequency limit is the HEMT (high electron mobility transistor), a field effect transistor made with two different semiconductors, AlGaAs and GaAs, using heterojunction technology, and the similar HBT (heterojunction bipolar transistor). [30]

GaAs can be made semi-insulating, allowing it to be used as a substrate on which circuits containing passive components as well as transistors can be fabricated by lithography. [30] By 1976 this led to the first integrated circuits (ICs) which functioned at microwave frequencies, called monolithic microwave integrated circuits (MMIC). [30] The word "monolithic" was added to distinguish these from microstrip PCB circuits, which were called "microwave integrated circuits" (MIC). Since then silicon MMICs have also been developed. Today MMICs have become the workhorses of both analog and digital high frequency electronics, enabling the production of single chip microwave receivers, broadband amplifiers, modems, and microprocessors.

See also

Related Research Articles

Cavity magnetron device for generating microwaves

The cavity magnetron is a high-powered vacuum tube that generates microwaves using the interaction of a stream of electrons with a magnetic field while moving past a series of open metal cavities. Electrons pass by the openings to these cavities and cause radio waves to oscillate within, similar to the way a whistle produces a tone when excited by an air stream blown past its opening. The frequency of the microwaves produced, the resonant frequency, is determined by the cavities' physical dimensions. Unlike other vacuum tubes such as a klystron or a traveling-wave tube (TWT), the magnetron cannot function as an amplifier in order to increase the intensity of an applied microwave signal; the magnetron serves solely as an oscillator, generating a microwave signal from direct current electricity supplied to the vacuum tube.

Transmitter Electronic device that emits radio waves

In electronics and telecommunications, a transmitter or radio transmitter is an electronic device which produces radio waves with an antenna. The transmitter itself generates a radio frequency alternating current, which is applied to the antenna. When excited by this alternating current, the antenna radiates radio waves.

Klystron

A klystron is a specialized linear-beam vacuum tube, invented in 1937 by American electrical engineers Russell and Sigurd Varian, which is used as an amplifier for high radio frequencies, from UHF up into the microwave range. Low-power klystrons are used as oscillators in terrestrial microwave relay communications links, while high-power klystrons are used as output tubes in UHF television transmitters, satellite communication, radar transmitters, and to generate the drive power for modern particle accelerators.

This is an index of articles relating to electronics and electricity or natural electricity and things that run on electricity and things that use or conduct electricity.

Terahertz radiation radio waves

Terahertz radiation – also known as submillimeter radiation, terahertz waves, tremendously high frequency (THF), T-rays, T-waves, T-light, T-lux or THz – consists of electromagnetic waves within the ITU-designated band of frequencies from 0.3 to 3 terahertz (THz). One terahertz is 1012 Hz or 1000 GHz. Wavelengths of radiation in the terahertz band correspondingly range from 1 mm to 0.1 mm (or 100 μm). Because terahertz radiation begins at a wavelength of one millimeter and proceeds into shorter wavelengths, it is sometimes known as the submillimeter band, and its radiation as submillimeter waves, especially in astronomy.

Super high frequency (SHF) is the ITU designation for radio frequencies (RF) in the range between 3 and 30 gigahertz (GHz). This band of frequencies is also known as the centimetre band or centimetre wave as the wavelengths range from one to ten centimetres. These frequencies fall within the microwave band, so radio waves with these frequencies are called microwaves. The small wavelength of microwaves allows them to be directed in narrow beams by aperture antennas such as parabolic dishes and horn antennas, so they are used for point-to-point communication and data links and for radar. This frequency range is used for most radar transmitters, wireless LANs, satellite communication, microwave radio relay links, and numerous short range terrestrial data links. They are also used for heating in industrial microwave heating, medical diathermy, microwave hyperthermy to treat cancer, and to cook food in microwave ovens.

Traveling-wave tube

A traveling-wave tube or traveling-wave tube amplifier is a specialized vacuum tube that is used in electronics to amplify radio frequency (RF) signals in the microwave range. The TWT belongs to a category of "linear beam" tubes, such as the klystron, in which the radio wave is amplified by absorbing power from a beam of electrons as it passes down the tube. Although there are various types of TWT, two major categories are:

Resonator device or system that exhibits resonance or resonant behavior, that is, it naturally oscillates at some frequencies, called its resonant frequencies, with greater amplitude than at others

A resonator is a device or system that exhibits resonance or resonant behavior, that is, it naturally oscillates at some frequencies, called its resonant frequencies, with greater amplitude than at others. The oscillations in a resonator can be either electromagnetic or mechanical. Resonators are used to either generate waves of specific frequencies or to select specific frequencies from a signal. Musical instruments use acoustic resonators that produce sound waves of specific tones. Another example is quartz crystals used in electronic devices such as radio transmitters and quartz watches to produce oscillations of very precise frequency.

Radio spectrum part of the electromagnetic spectrum from 3 Hz to 3000 GHz (3 THz)

The radio spectrum is the part of the electromagnetic spectrum with frequencies from 30 Hertz to 300 GHz. Electromagnetic waves in this frequency range, called radio waves, are extremely widely used in modern technology, particularly in telecommunication. To prevent interference between different users, the generation and transmission of radio waves is strictly regulated by national laws, coordinated by an international body, the International Telecommunication Union (ITU).

Extremely high frequency radio waves

Extremely high frequency (EHF) is the International Telecommunication Union (ITU) designation for the band of radio frequencies in the electromagnetic spectrum from 30 to 300 gigahertz (GHz). It lies between the super high frequency band, and the far infrared band, the lower part of which is also referred to as the terahertz gap. Radio waves in this band have wavelengths from ten to one millimetre, so it is also called the millimetre band and radiation in this band is called millimetre waves, sometimes abbreviated MMW or mmW. Millimetre-length electromagnetic waves were first investigated in the 1890s by Indian scientist Jagadish Chandra Bose.

Horn antenna

A horn antenna or microwave horn is an antenna that consists of a flaring metal waveguide shaped like a horn to direct radio waves in a beam. Horns are widely used as antennas at UHF and microwave frequencies, above 300 MHz. They are used as feed antennas for larger antenna structures such as parabolic antennas, as standard calibration antennas to measure the gain of other antennas, and as directive antennas for such devices as radar guns, automatic door openers, and microwave radiometers. Their advantages are moderate directivity, low standing wave ratio (SWR), broad bandwidth, and simple construction and adjustment.

Gunn diode diode

A Gunn diode, also known as a transferred electron device (TED), is a form of diode, a two-terminal passive semiconductor electronic component, with negative resistance, used in high-frequency electronics. It is based on the "Gunn effect" discovered in 1962 by physicist J. B. Gunn. Its largest use is in electronic oscillators to generate microwaves, in applications such as radar speed guns, microwave relay data link transmitters, and automatic door openers.

Gyrotron

A gyrotron is a class of high-power linear-beam vacuum tubes which generates millimeter-wave electromagnetic waves by the cyclotron resonance of electrons in a strong magnetic field. Output frequencies range from about 20 to 527 GHz, covering wavelengths from microwave to the edge of the terahertz gap. Typical output powers range from tens of kilowatts to 1–2 megawatts. Gyrotrons can be designed for pulsed or continuous operation.

Backward-wave oscillator

A backward wave oscillator (BWO), also called carcinotron or backward wave tube, is a vacuum tube that is used to generate microwaves up to the terahertz range. Belonging to the traveling-wave tube family, it is an oscillator with a wide electronic tuning range.

Radio-frequency engineering, or RF engineering, is a subset of electrical and electronic engineering involving the application of transmission line, waveguide, antenna and electromagnetic field principles to the design and application of devices that produce or utilize signals within the radio band, the frequency range of about 20 kHz up to 300 GHz.

Barkhausen–Kurz tube high frequency vacuum tube electronic oscillator


The Barkhausen–Kurz tube, also called the retarding-field tube, reflex triode, B–K oscillator, and Barkhausen oscillator was a high frequency vacuum tube electronic oscillator invented in 1920 by German physicists Heinrich Georg Barkhausen and Karl Kurz. It was the first oscillator that could produce radio power in the ultra-high frequency (UHF) portion of the radio spectrum, above 300 MHz. It was also the first oscillator to exploit electron transit time effects. It was used as a source of high frequency radio waves in research laboratories, and in a few UHF radio transmitters through World War 2. Its output power was low which limited its applications. However it inspired research that led to other more successful transit time tubes such as the klystron, which made the low power Barkhausen-Kurz tube obsolete.

Sutton tube

A Sutton tube, or reflex klystron, is a type of vacuum tube used to generate microwaves. It is a low-power device used primarily for two purposes; one is to provide a tuneable low-power frequency source for the local oscillators in receiver circuits, and the other, with minor modifications, as a switch that could turn on and off another microwave source. The second use, sometimes known as a soft Sutton tube or rhumbatron switch, was a key component in the development of microwave radar during World War II. Microwave switches of all designs, including these, are more generally known as T/R tubes or T/R cells.

In radio systems, many different antenna types are used with specialized properties for particular applications. Antennas can be classified in various ways. The list below groups together antennas under common operating principles, following the way antennas are classified in many engineering textbooks.

References

  1. Hitchcock, R. Timothy (2004). Radio-frequency and Microwave Radiation. American Industrial Hygiene Assn. p. 1. ISBN   978-1931504553.
  2. 1 2 Kumar, Sanjay; Shukla, Saurabh (2014). Concepts and Applications of Microwave Engineering. PHI Learning Pvt. Ltd. p. 3. ISBN   978-8120349353.
  3. Jones, Graham A.; Layer, David H.; Osenkowsky, Thomas G. (2013). National Association of Broadcasters Engineering Handbook, 10th Ed. Taylor & Francis. p. 6. ISBN   978-1136034107.
  4. Pozar, David M. (1993). Microwave Engineering Addison–Wesley Publishing Company. ISBN   0-201-50418-9.
  5. Sorrentino, R. and Bianchi, Giovanni (2010) Microwave and RF Engineering , John Wiley & Sons, p. 4, ISBN   047066021X.
  6. 1 2 Seybold, John S. (2005). Introduction to RF Propagation. John Wiley and Sons. pp. 55–58. ISBN   978-0471743682.
  7. 1 2 Golio, Mike; Golio, Janet (2007). RF and Microwave Passive and Active Technologies. CRC Press. pp. I.2–I.4. ISBN   978-1420006728.
  8. Microwave Oscillator notes by Herley General Microwave
  9. 1 2 Sisodia, M. L. (2007). Microwaves : Introduction To Circuits, Devices And Antennas. New Age International. pp. 1.4–1.7. ISBN   978-8122413380.
  10. Liou, Kuo-Nan (2002). An introduction to atmospheric radiation. Academic Press. p. 2. ISBN   978-0-12-451451-5 . Retrieved 12 July 2010.
  11. "IEEE 802.20: Mobile Broadband Wireless Access (MBWA)". Official web site. Retrieved August 20, 2011.
  12. "ALMA website" . Retrieved 2011-09-21.
  13. "Welcome to ALMA!" . Retrieved 2011-05-25.
  14. Wright, E.L. (2004). "Theoretical Overview of Cosmic Microwave Background Anisotropy". In W. L. Freedman. Measuring and Modeling the Universe. Carnegie Observatories Astrophysics Series. Cambridge University Press. p. 291. arXiv: astro-ph/0305591 . Bibcode:2004mmu..symp..291W. ISBN   978-0-521-75576-4.
  15. "The way to new energy". ITER. 2011-11-04. Retrieved 2011-11-08.
  16. "Electron Cyclotron Resonance Heating (ECRH)". Ipp.mpg.de. Archived from the original on 2011-09-27. Retrieved 2011-11-08.
  17. Silent Guardian Protection System. Less-than-Lethal Directed Energy Protection. raytheon.com
  18. "Frequency Letter bands". Microwave Encyclopedia. Microwaves101 website, Institute of Electrical and Electronic Engineers (IEEE). 14 May 2016. Retrieved 1 July 2018.
  19. Golio, Mike; Golio, Janet (2007). RF and Microwave Applications and Systems. CRC Press. pp. 1.9–1.11. ISBN   978-1420006711.
  20. "eEngineer – Radio Frequency Band Designations". Radioing.com. Retrieved 2011-11-08.
  21. PC Mojo – Webs with MOJO from Cave Creek, AZ (2008-04-25). "Frequency Letter bands – Microwave Encyclopedia". Microwaves101.com. Retrieved 2011-11-08.
  22. For other definitions see Letter Designations of Microwave Bands.
  23. Skolnik, Merrill I. (2001) Introduction to Radar Systems, Third Ed., p. 522, McGraw Hill. 1962 Edition full text
  24. Nave, Rod. "Interaction of Radiation with Matter". HyperPhysics. Retrieved 20 October 2014.
  25. Goldsmith, JR (December 1997). "Epidemiologic evidence relevant to radar (microwave) effects". Environmental Health Perspectives. 105 (Suppl. 6): 1579–1587. doi:10.2307/3433674. JSTOR   3433674. PMC   1469943 . PMID   9467086.
  26. Philip L. Stocklin, U.S. Patent 4,858,612 , December 19, 1983
  27. Andjus, R.K.; Lovelock, J.E. (1955). "Reanimation of rats from body temperatures between 0 and 1 °C by microwave diathermy". The Journal of Physiology. 128 (3): 541–546. doi:10.1113/jphysiol.1955.sp005323. PMC   1365902 . PMID   13243347.
  28. "Resources for You (Radiation-Emitting Products)". US Food and Drug Administration home page. U.S. Food and Drug Administration. Retrieved 20 October 2014.
  29. Hong, Sungook (2001). Wireless: From Marconi's Black-box to the Audion. MIT Press. pp. 5–9, 22. ISBN   978-0262082983.
  30. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Roer, T.G. (2012). Microwave Electronic Devices. Springer Science and Business Media. pp. 1–12. ISBN   978-1461525004.
  31. 1 2 3 4 5 Sarkar, T. K.; Mailloux, Robert; Oliner, Arthur A. (2006). History of Wireless. John Wiley and Sons. pp. 474–486. ISBN   978-0471783015.
  32. Emerson, D.T. (February 1998). "The work of Jagdish Chandra Bose: 100 years of MM-wave research". National Radio Astronomy Observatory.
  33. 1 2 Packard, Karle S. (September 1984). "The Origin of Waveguides: A Case of Multiple Rediscovery" (PDF). IEEE Transactions on Microwave Theory and Techniques. MTT-32 (9): 961–969. Bibcode:1984ITMTT..32..961P. CiteSeerX   10.1.1.532.8921 . doi:10.1109/tmtt.1984.1132809 . Retrieved March 24, 2015.
  34. Strutt, William (Lord Rayleigh) (February 1897). "On the passage of electric waves through tubes, or the vibrations of dielectric cylinders". Philosophical Magazine. 43 (261): 125–132. doi:10.1080/14786449708620969.
  35. Kizer, George (2013). Digital Microwave Communication: Engineering Point-to-Point Microwave Systems. John Wiley and Sons. p. 7. ISBN   978-1118636800.
  36. Lee, Thomas H. (2004). Planar Microwave Engineering: A Practical Guide to Theory, Measurement, and Circuits, Vol. 1. Cambridge University Press. pp. 18, 118. ISBN   978-0521835268.
  37. "Microwaves span the English Channel" (PDF). Short Wave Craft. Vol. 6 no. 5. New York: Popular Book Co. September 1935. pp. 262, 310. Retrieved March 24, 2015.
  38. 1 2 Free, E.E. (August 1931). "Searchlight radio with the new 7 inch waves" (PDF). Radio News. Vol. 8 no. 2. New York: Radio Science Publications. pp. 107–109. Retrieved March 24, 2015.
  39. Ayto, John (2002). 20th century words. p. 269. ISBN   978-7560028743.
  40. Riordan, Michael; Lillian Hoddeson (1988). Crystal fire: the invention of the transistor and the birth of the information age. US: W. W. Norton & Company. pp. 89–92. ISBN   978-0-393-31851-7.
  41. "Cooking with Short Waves" (PDF). Short Wave Craft. 4 (7): 394. November 1933. Retrieved 23 March 2015.
  42. Kurokawa, K. (July 1969). "Some Basic Characteristics of Broadband Negative Resistance Oscillator Circuits". Bell System Tech. J. 48 (6): 1937–1955. doi:10.1002/j.1538-7305.1969.tb01158.x . Retrieved December 8, 2012.