Oerlikon 20 mm cannon

Last updated
Oerlikon 20 mm cannon
20mm gun.jpg
A modern Oerlikon cannon (Oerlikon 20mm/85 KAA) on a Royal Navy warship
Type Autocannon
Place of originSwitzerland/Italy
Service history
In service1937–present
Used byVarious
Wars World War II, various
Production history
DesignerReinhold Becker
Designed1935
Manufacturer Oerlikon
Produced1937–
No. built124,734 [1]
Variants Oerlikon FF
MG FF cannon
Specifications
MassL70
Total gun barrel weight: 68.04 kilograms (150.0  lb)
Minus breech mechanism: 20.865 kg (46.00 lb)
L85
Empty: 92.0 kilograms (202.8  lb)
Loaded with 200 rounds: 182.0 kg (401.2 lb)
LengthL70
Overall: 2,210 mm (87 in)
Bore: 1,400 mm (55 in)
L85
Overall: n/a
Bore: 1,700 mm (67 in)

Shell L70: 20×110mmRB
L85: 20×128mm
Shell weightHE: 123 g (4.3 oz)
HE/T: 116 g (4.1 oz)
Caliber 20 mm (0.787inch)
BarrelsSingle barrel (progressive RH parabolic twist, 9 grooves)
Action API blowback
Elevation Manual, -15°/+90°
Traverse Manual, full 360°
Rate of fire L70:
Cyclic: 450 rounds per minute
Practical: 250-320 rounds per minute
L85:
Cyclic: 900 to 1,000 rounds per minute
Muzzle velocity L70: 820 m/s (2,700 ft/s)
L85: 1,050 m/s (3,400 ft/s)
Effective firing rangeAgainst low-flying aircraft (HE round)
L70: 914 m (1,000 yd)
L85: 1,500 m (1,600 yd)
Maximum firing rangeHE round at 45°
L70: 4,389 m (4,800 yd)
L85: 6,800 m (7,400 yd)
Feed systemCylindrical magazine holding 60 rounds, Later adjusted to be a belt fed gun

The Oerlikon 20 mm cannon is a series of autocannons, based on an original German Becker Type M2 20 mm cannon design that appeared very early in World War I. It was widely produced by Oerlikon Contraves and others, with various models employed by both Allied and Axis forces during World War II, and many versions are still in use today. [2] [3]

Contents

History

Origins

During World War I, the German industrialist Reinhold Becker developed a 20 mm caliber cannon, known now as the 20 mm Becker using the Advanced Primer Ignition blowback (API blowback) method of operation. This used a 20×70mmRB cartridge and had a cyclic rate of fire of 300 rpm. It was used on a limited scale as an aircraft gun on Luftstreitkräfte warplanes, and an anti-aircraft gun towards the end of that war.

Because the Treaty of Versailles banned further production of such weapons in Germany, the patents and design works were transferred in 1919 to the Swiss firm SEMAG (Seebach Maschinenbau Aktien Gesellschaft) based near Zürich. SEMAG continued development of the weapon, and in 1924 had produced the SEMAG L, a heavier weapon (43 kg) that fired more powerful 20×100mmRB ammunition at a slightly higher rate of fire, 350 rpm.

In 1924 SEMAG failed. The Oerlikon firm, named after the Zürich suburb of Oerlikon where it was based, then acquired all rights to the weapon, plus the manufacturing equipment and the employees of SEMAG.

Oerlikon

In 1927 the Oerlikon S was added to the existing product line. This fired a still larger cartridge (20x110RB) to achieve a muzzle velocity of 830 m/s (versus 490 m/s for the original Becker 20x70RB gun), at the cost of increased weight and a reduced rate of fire (280 rpm). The purpose of this development was to improve the performance of the gun as an anti-tank and anti-aircraft weapon, which required a higher muzzle velocity. An improved version known as the 1S followed in 1930.

Three sizes of gun with their different ammunition and barrel length, but very similar mechanisms, continued to be developed in parallel. In 1930 Oerlikon reconsidered the application of its gun in aircraft and introduced the AF and AL, designed to be used in flexible mounts, i.e. manually aimed by a gunner. The 15-round box magazine used by earlier versions of the gun was replaced by drum magazine holding 15 or 30 rounds.

In 1935 it made an important step by introducing a series of guns designed to be mounted in or on the wings of fighter aircraft. Designated with FF for Flügelfest meaning "wing-mounted", these weapons were again available in the three sizes, with designations FF, FFL and FFS. The FF fired a slightly larger cartridge than the AF, 20x72RB, but the major improvement in these weapons was a significant increase in rate of fire. The FF weighed 24 kg and achieved a muzzle velocity of 550 to 600 m/s with a rate of fire of 520 rpm. The FFL of 30 kg fired a projectile at a muzzle velocity of 675 m/s with a rate of fire of 500 rpm. And the FFS, which weighed 39 kg, delivered a high muzzle velocity of 830 m/s at a rate of fire of 470 rpm. [4]

Apart from changes to the design of the guns for wing-mounting and remote control, larger drums were introduced as it would not be possible to exchange magazines in flight. For the FF series drum sizes of 45, 60, 75 and 100 rounds were available, but most users chose the 60-round drum.

The 1930s were a period of global re-armament, and a number of foreign firms took licenses for the Oerlikon family of aircraft cannon. In France, Hispano-Suiza manufactured development of the FFS as the Hispano-Suiza HS.7 and Hispano-Suiza HS.9, for installation between the cylinder banks of its V-12 engines. In Germany, Ikaria further developed the FF gun as the MG FF, firing 20x80RB ammunition. And the Imperial Japanese Navy, after evaluating all three guns, ordered developments of the FF and FFL as the Type 99-1 and Type 99-2.

The incorporation of the improvements of the FFS in a new anti-aircraft gun produced, in 1938, the Oerlikon SS. Oerlikon realized further improvements in rate of fire on the 1SS of 1942, and the 2SS of 1945 which achieved 650 rpm. However, it was the original SS gun which was widely adopted as anti-aircraft gun, being especially widely used by Allied navies during World War II.

This gun used a 400-grain (26-gram) charge of IMR 4831 smokeless powder to propel a 2,000-grain (130-gram) projectile at 2,800 feet (850 meters) per second. [5]

World War II

A Royal Navy Oerlikon gunner at his gun mount aboard the Dido-class cruiser HMS Dido in 1942 HMS Dido gun.jpg
A Royal Navy Oerlikon gunner at his gun mount aboard the Dido-class cruiser HMS Dido in 1942

The Oerlikon FF was installed as armament on some fighters of the 1930s, such as the Polish PZL P.24G. Locally produced derivatives of the Oerlikon cannon were used much more extensively, on aircraft, on ships and on land. In the air, the Ikaria MG FF was used as armament on a number of German aircraft, of which the most famous is the Messerschmitt Bf 109. The Japanese Navy similarly used their copy of the FF, designated the Type 99 Mark One cannon on a number of types including the Mitsubishi A6M Zero. Later in the war, they also equipped fighters including the Zero with the Type 99 Mark Two, a version of the more powerful and faster-firing Oerlikon FFL.

The French firm of Hispano-Suiza was a manufacturer of aircraft engines, and it marketed the moteur-canon combination of its 12X and 12Y engines with a H.S.7 or H.S.9 cannon installed between the cylinder banks. The gun fired through the hollow propeller hub, this being elevated above the crankcase by the design of the gearing. Such armament was installed on the Morane-Saulnier M.S.406 and some other types. Similar German installations of the MG FF were not successful.

Diagrams showing basic design and colour-coding of British HE/Incendiary, Tracer and HE/Incendiary/Tracer shells for the 20 mm Oerlikon gun British 20 mm Oerlikon shell diagrams.jpg
Diagrams showing basic design and colour-coding of British HE/Incendiary, Tracer and HE/Incendiary/Tracer shells for the 20 mm Oerlikon gun

The Oerlikon became best known in its naval applications. Initially the Oerlikon was not looked upon favorably by the Royal Navy as a short-range anti-aircraft gun. All through 1937-1938 Lord Louis Mountbatten, then a Captain in the Royal Navy, waged a lone campaign within the Royal Navy to set up an unprejudiced trial for the Oerlikon 20 mm gun, but it was all in vain. It was not until the Commander-in-Chief of the Home Fleet, Admiral Sir Roger Backhouse, was appointed First Sea Lord that Mountbatten's efforts bore fruit. During the first half of 1939 a contract for 1,500 guns was placed in Switzerland. However, due to delays and then later the Fall of France in June 1940, only 109 guns reached the United Kingdom. All Oerlikon guns imported from Switzerland, in 1940, were mounted on various gun carriages to serve as light AA-guns on land.

Just a few weeks before the Fall of France, the Oerlikon factory approved manufacture of their gun in the United Kingdom, under licence. The Royal Navy managed to smuggle out the necessary drawings and documents from Zürich. The production of the first British-made Oerlikon guns started in Ruislip, London, at the end of 1940. The first guns were delivered to the Royal Navy in March or April, 1941. The RAF Regiment made extensive use of Oerlikon guns in the anti-aircraft role. These were the principal armament for its Light Anti-Aircraft squadrons in North Africa, the Middle East, Italy, and North Western Europe, until the introduction of the Bofors 40/L60 40mm gun from 1943, although many squadrons retained a mix of guns until the end of World War 2. Squadrons in the Far East were equipped exclusively with Oerlikons.

1945, a row of 20 mm Oerlikon guns aboard the Essex-class aircraft carrier USS Hornet CV-12 20mm 1945.jpg
1945, a row of 20 mm Oerlikon guns aboard the Essex-class aircraft carrier USS Hornet

The Oerlikon gun was installed aboard United States Navy ships from 1942, replacing the M2 Browning machine gun, which lacked range and firepower, and largely superseding the 1.1"/75 caliber gun, which was heavier and had less mechanical reliability. It became famous in the naval anti-aircraft role, providing an effective defense at short ranges (in practice up to 1.5 km) at which heavier guns had difficulty tracking a target. The gun was eventually abandoned as a major anti-air weapon due to its lack of stopping power against heavy aircraft and against Japanese kamikaze attacks during the Pacific War. It was largely superseded by the Bofors 40 mm gun and the 3"/50 Mark 22 gun. It provided a useful increase in firepower over the .50 cal machine gun when adapted and fitted to some aircraft. However, it had some problems with jamming in the ammunition feed.

The Royal Canadian Navy popularized the use of the Oerlikon gun as an anti-ship and anti-submarine gun - while it was not effective against the armour of most larger ships, it was used extensively and effectively against U-Boats, and on the decks of larger ships. A handful of corvettes were fitted with the weapon toward the end of the war, but it appeared more commonly on frigates and destroyers at the time.

The Oerlikon was also used as the basis for the Polsten gun, designed by Polish engineers in exile in the United Kingdom. The gun went into service in 1944, and was used well into the 1950s, among other uses, on Cromwell tanks [ citation needed ] and early model Centurion tanks.

Romania purchased 45 pieces from Germany during the first half of World War II. [6]

Post-war

It is still in use today on some naval units, theoretically as a last-recourse anti-air weapon, but mainly used for firing warning shots or incapacitating small vessels.

Description

The aiming sight of the Oerlikon gun Oerlikon20 mm cannon on the SS Jeremiah O'Brien.jpg
The aiming sight of the Oerlikon gun

Very unusually for a high-powered autocannon, the Oerlikon and its derivatives feature blowback operation: the bolt is not locked to the breech of the gun at the moment of firing. Non-locking, simple blowback designs are commonplace in much lighter weapons, such as small-caliber semi-automatic pistols. No locking is required, as with such low-power cartridges the static inertia of the bolt or bolt and slide - the physical tendency of heavy components to resist rapid acceleration - is adequate to ensure that the projectile has left the muzzle and the gas pressure in the barrel is down to a safe level before the breech opens (while the bolt spring also resists the opening of the breech, in practical terms its contribution is too small to be relevant). [7] In contrast, 20mm cartridges are far too powerful, and efficient autocannon barrels too long, for this basic system to be practical; so the Oerlikon uses Advanced Primer Ignition (API) to augment the resistance of the bolt. In API blowback weapons, the firing pin fires the cartridge while the bolt is still traveling forward so that the gas pressure has to overcome the forward momentum of the bolt as well, before it can push it to the rear. To facilitate this, the Oerlikon's chamber is longer than needed to contain the cartridge, and the end of the bolt, which is the same diameter as the case, actually enters this extended chamber behind the cartridge before firing. As a result, when firing occurs, the forward force of the bolt and spring acts against the force of the propellant gases until the latter overcome the former and start pushing case, bolt and spring backwards. If the bolt had stopped at the mouth of the chamber as in a simple blowback gun, this momentum would be neutralized and the additional forward oppositional force would not exist. A second advantage of this unusual arrangement is that after firing, the bolt and case have a short, but significant, distance to travel rearwards before the bolt-end re-emerges and the case in turn begins to leave the chamber—providing more time for gas pressure to drop to the necessary safe level. This system permits blowback to be used in far more powerful weapons than normal. Nevertheless, compared to guns with a locking mechanism a fairly heavy bolt must be employed; while to give this heavy bolt sufficient forward speed, a large spring is required (and Oerlikons, distinctively, have this component wrapped around their barrels.) These features will limit the rate of fire of such guns, unless other steps are taken—as in the final model of the Japanese 99 Mark 2. [4]

This unique chamber and bolt design necessitates the use of a characteristically shaped cartridge: the case has straight sides, very little neck, and a rebated rim. The straight sides allows the case to slide back and forward in the cylindrical chamber. The neck is not supported while this happens and therefore expands when the case is fired, and the rebated rim allows the face of the bolt, with its extractor claw hooked over the rim, to fit within the chamber. To ease the motion of the case, the ammunition needed to be greased, which was a drawback of the Oerlikon cannon. An alternative developed during World War II was the so-called fluted chamber, which had grooves that allowed propellant gas to seep between the chamber wall and the case, taking over the role of the grease. [4]

HMCS Haida Hamilton Ontario 13.jpg
Side view of the twin Oerlikon gun mount
HMCS Haida Hamilton Ontario 14.jpg
Rear view of the twin Oerlikon gun mount
A twin Oerlikon gun mount from the Tribal-class destroyer HMCS Haida

Ammunition feed is typically by a 60-round drum magazine on the top of the gun. During sustained firing, the magazine must be frequently changed, reducing the effective rate of fire. Belt-fed versions of the gun were developed to overcome this limitation. A trigger in the right-hand grip controls fire. Used cartridges are ejected from below the breech.

Different nations and services operated a number of mounting types for the same basic gun. In a typical single-barrel naval version, it is free-swinging on a fixed pedestal mounting with a flat armored shield affording some protection for the crew. The cannon is aimed and fired by a gunner using, in its simplest form, a ring-and-bead sight. The gunner is attached to the weapon by a waist-belt and shoulder supports. For this reason, some mountings existed with a height-adjustment feature to compensate for different sized gunners. A "piece chief" designates targets and the feeder changes exhausted magazines.

During World War II, twin and quadruple Oerlikon mounts were developed, both for army and for navy use. The British Navy operated a hydraulically operated twin-gun mount. The US Navy operated a quad mount developed for PT boats by Elco Naval Division, Electric Boat Company, called the Elco "Thunderbolt" Mount. Prototypes were built and tested in late 1942 and operationally deployed on several Elco PT Boats in the Mediterranean. [8] [9] It was also placed experimentally on the battleships Arkansas, Colorado, Maryland, West Virginia, Washington, Massachusetts, and training ship Wyoming.

See also

Related Research Articles

Machine gun fully automatic mounted or portable firearm

A machine gun is a fully automatic mounted or portable firearm designed to fire rifle cartridges in rapid succession from an ammunition belt or magazine. Not all fully automatic firearms are machine guns. Submachine guns, rifles, assault rifles, battle rifles, shotguns, pistols or cannons may be capable of fully automatic fire, but are not designed for sustained fire. As a class of military rapid-fire guns, machine guns are fully automatic weapons designed to be used as support weapons and generally used when attached to a mount or fired from the ground on a bipod or tripod. Many machine guns also use belt feeding and open bolt operation, features not normally found on rifles.

Autocannon rapid-fire projectile weapon that fires armour-piercing or explosive shells

An autocannon or automatic cannon is a large, fully automatic, rapid-fire projectile weapon that fires armour-piercing or explosive shells, as opposed to the bullet fired by a machine gun. Autocannons have a longer range and a larger calibre than machine guns, but are usually smaller than tank guns, howitzers, field guns or other artillery. When used on its own, the word "autocannon" indicates a non-rotary weapon. When multiple rotating barrels are involved, the word "rotary" is added, and such a weapon is referred to as a "rotary autocannon". Modern autocannons are typically not single soldier-portable or stand-alone units due to high weight and recoil; rather they are usually vehicle-mounted, aircraft-mounted, or boat-mounted, or even remote-operated as in some naval applications. As such, ammunition is typically fed from a belt to reduce reloading or for a faster rate of fire, but a magazine remains an option. Common types of ammunition, among a wide variety, include HEIAP, high-explosive dual-purpose (HEDP) and more specialised armour-piercing (AP) types, mainly composite rigid (APCR) and discarding sabot (APDS).

MK 108 cannon Type of Autocannon

The MK 108 was a 30 mm caliber autocannon manufactured in Germany during World War II by Rheinmetall‑Borsig for use in aircraft.

MG 151 cannon Type of Aircraft Cannon

The MG 151 was a 15 mm aircraft-mounted autocannon produced by Waffenfabrik Mauser during World War II. Its 20mm variant, the 20 mm MG 151/20 cannon, was widely used on German Luftwaffe fighters, night fighters, fighter-bombers, bombers and ground-attack aircraft. Salvaged guns saw post-war use by other nations.

AK-230 A Soviet fully automatic naval twin 30 mm gun

The AK-230 is a Soviet fully automatic naval twin 30 mm gun. Its primary function is anti-aircraft. It is mounted in an enclosed automatic turret and directed by radar. AK-230 is widely used, mounted on big warships as well as small craft. About 1450 guns were produced in the USSR, and about 300 were produced in China as the Type 69. It was succeeded by the more powerful AK-630 from the mid-to-late 1970s.

MG 15 Type of Machine gun

The MG 15 was a German 7.92 mm machine gun designed specifically as a hand manipulated defensive gun for combat aircraft during the early 1930s. By 1941 it was replaced by other types and found new uses with ground troops.

Revolver cannon type of autocannon

A revolver cannon is a type of autocannon, commonly used as an aircraft gun. It uses a cylinder with multiple chambers, like those of a revolver handgun, to speed up the loading-firing-ejection cycle. Some examples are also power-driven, to further speed the loading process. Unlike a rotary cannon, a revolver cannon has only a single barrel, thus its spun weight is lower. Automatic revolver cannons have been produced by many different manufacturers.

Hispano-Suiza HS.404 20 mm autocannon

The HS.404 is an autocannon originally designed and produced by Spanish/French company Hispano-Suiza in the mid-1930s. It was widely used as an aircraft, naval and land-based weapon by French, British, American and other military services, particularly during World War II. The cannon is also referred to as Birkigt type 404, after its designer Marc Birkigt and later versions based on British development are known as 20 mm Hispano.

Blowback is a system of operation for self-loading firearms that obtains energy from the motion of the cartridge case as it is pushed to the rear by expanding gas created by the ignition of the propellant charge.

MG FF cannon 20 mm autocannon aircraft armament

The MG FF was a drum-fed, blowback-operated, 20 mm aircraft autocannon, developed in 1936 by Ikaria Werke Berlin of Germany. It was a derivative of the Swiss Oerlikon FF F cannon, with the Oerlikon FF design itself a development of the Imperial German World War I Becker 20 mm cannon, and was designed to be used in space-limited, fixed mountings such as inside aircraft wings, although it saw use as both an offensive and a defensive weapon, in both fixed and flexible format. It saw widespread use in those roles by the German Luftwaffe, particularly during the early stages of World War II, although from 1941 onwards it was gradually replaced by the Mauser firm's 20 mm MG 151/20. MG FF stands for Maschinengewehr Flügel Fest, which translates into "machine gun, wing, fixed"; this reflects the fact that in Luftwaffe practice guns of 20 mm or less were designated as "machine guns" (maschinengewehr) as opposed to larger "machine cannons", or autocannons, which were "MK", for maschinenkanone The "wing, fixed" part reflects the fact that the primary motivation behind its design was to create a 20 mm caliber weapon that was compact and light enough to be mounted in the wings of aircraft, especially fighters.

QF 2-pounder naval gun British naval gun

The 2-pounder gun, officially designated the QF 2-pounder and universally known as the pom-pom, was a 40-millimetre (1.6 in) British autocannon, used as an anti-aircraft gun by the Royal Navy. The name came from the sound that the original models make when firing. This QF 2-pounder was not the same gun as the Ordnance QF 2 pounder, used by the British Army as an anti-tank gun and a tank gun, although they both fired 2-pound (0.91 kg), 40-millimetre (1.6 in) projectiles.

The FF were a series of 20mm autocannon introduced by Oerlikon in the late 1920s. The name comes from the German term Flügel Fest, meaning wing mounted, fixed, being one of the first 20mm guns to be small and light enough to fit into a fighter aircraft's wing. The FF series inspired many 20mm cannon used in World War II, including the Hispano-Suiza HS.404, the German MG FF, and the Japanese IJNAS's Type 99 cannon.

Type 96 25 mm AT/AA Gun Type of Anti-Aircraft/Anti-tank, Autocannon

The Type 96 25mm Gun was an automatic cannon used by the Imperial Japanese Navy during World War II. A locally-built variant of the French Hotchkiss 25mm anti-aircraft gun, it was designed as a dual-purpose weapon for use against armored vehicles and aircraft, but was primarily used as an anti-aircraft gun in fixed mounts with one to three guns.

Rheinmetall Mk 20 Rh-202 Type of Autocannon

The Rheinmetall Mk 20 RH-202 is a 20 mm caliber autocannon designed and produced by Rheinmetall. It fires the 20×139mm ammunition originally developed for the Hispano-Suiza HS.820.

Becker Type M2 20 mm cannon 20 mm autocannon aircraft armament

The Becker Type M2 20 mm cannon was a German autocannon developed for aircraft use during World War I by Stahlwerke Becker. It was first mass-produced in 1916 and was installed in a variety of aircraft. It was the only German autocannon to see service in the air during the war.

The Type 99 Mark 1 machine gun and Type 99 Mark 2 machine gun were Japanese versions of the Oerlikon FF and Oerlikon FFL autocannons respectively. They were adopted by the Imperial Japanese Navy (IJN) in 1939 and served as their standard aircraft autocannon during World War II.

Hispano-Suiza HS.820

The HS.820 was a 20 mm caliber autocannon developed by Hispano-Suiza primarily for aircraft use, but more widely used in a series of ground-based anti-aircraft guns. After Oerlikon purchased Hispano's armaments division in 1970, the HS.820 became the Oerlikon KAD, supplanting Oerlikon's own KAA and KAB weapons in the process. A US-built model, the M139, saw some use on vehicles.

M1919 Browning machine gun Type of Medium machine gunGeneral-purpose machine gun (M1919A6)

The M1919 Browning is a .30 caliber medium machine gun that was widely used during the 20th century, especially during World War II, the Korean War, and the Vietnam War. The M1919 saw service as a light infantry, coaxial, mounted, aircraft, and anti-aircraft machine gun by the U.S. and many other countries.

Oerlikon KBA Type of Autocannon

The Oerlikon KBA is a 25 mm (25×137mm) autocannon, developed as a close range weapon for the mechanized battlefield originally made by Oerlikon Contraves AG.

RSA (missile) Type of Surface-to-air missile

The RSA is one of the earliest surface-to-air missiles systems, developed by the Swiss companies Oerlikon-Bührle and Contraves starting in 1947. The missile went through a rapid development process with several upgraded versions, and was the first anti-aircraft missile offered for commercial sale when it was placed on the market in the RSC-50 form. The US tested 25 of the slightly different RSC-51 model under the name MX-1868. No further sales were forthcoming. Several improved versions followed, including the RSC-54, RSC-56, RSC-57 and RSC/RSD-58. These saw small numbers of sales, mostly as training rounds.

References

  1. Budge, Kent G. (2014). "20mm Oerlikon Light Antiaircraft Gun". The Pacific War Online Encyclopedia. Retrieved 30 May 2019.
  2. "Switzerland Oerlikon 20 mm/70 (0.79") Mark 1"". NavWeaps.com. 14 January 2011. Retrieved 24 September 2011.
  3. "Britain 20 mm/85 (0.79") GAM-BO1". NavWeaps.com. 21 June 2008. Retrieved 23 October 2011.
  4. 1 2 3 Williams (2000).
  5. Johnson (1944), Appendix.
  6. Axworthy, Mark (1995). Third Axis, Fourth Ally: Romanian Armed Forces in the European War, 1941–1945. London, UK: Arms and Armour Press. p. 30. ISBN   978-1-85409-267-0.
  7. "The Machine Gun", Volume4, George M.Chinn., page 12
  8. Elco Naval Division Memo. General Information on Elco Thunderbolt Mount, Mark II, Bayonne, NJ: December 1, 1942.
  9. Motor Torpedo Boat Squadron Twenty-Nine Memo to CNO. The Electric Boat Company Thunderbolt Quadruple 20 MM Powered Mount installed on PTs, operational report on, New York, NY: 19 February 1945.

Bibliography