A planchetEnglish: /ˈplæntʃət/ is a round metal disk that is ready to be struck as a coin. An older word for planchet is flan. They are also referred to as blanks.
A planchetEnglish: /ˈplæntʃət/ is a round metal disk that is ready to be struck as a coin. An older word for planchet is flan. They are also referred to as blanks.
The preparation of the flan or planchet has varied over the years. In ancient times, the flan was heated before striking because the metal that the coin dies were made of was not as hard as dies today, and the dies would have worn faster and broken sooner had the flan not been heated to a high temperature to soften it.
An unusual method was used to mint the one-sided, bowl-shaped pfennigs of the Holy Roman Empire. The planchet used for these so-called Schüsselpfennigs was larger than the coin die itself. The coins were made by striking with only one upper die on the larger planchet. As a result, the perimeter of the planchet was pressed upwards in the shape of a bowl or plate. Until the 18th century they were minted mainly in the Harz Mountains. The curved shape of the pfennig was very useful for handling small change because it was easier to grip than a flat coin. [1]
Today's dies are made from hardened steel, and the presses use many thousands of pounds of force to strike coins (varying according to the size of the coin and the complexity and relief of the design). In addition, today's coins have much lower relief than ancient coins. Because of this, the planchet no longer needs to be heated immediately before striking, although it is annealed by heating and slow cooling which softens the coin.
Preparation of the modern planchet involves several steps. First, the metal (or metals in the case of clad or multilayered coins) is rolled out into a large roll or sheet of the correct thickness. This process is often done by third parties, not by the mint itself. These flat rolls or sheets of metal are then punched out into round blanks that are a little larger than the coin being struck. The blanks are then subjected to an annealing process that softens the metal through heating to approximately 750 degrees Celsius (1400 degrees Fahrenheit) and are then slowly air cooled. They are then washed to remove residue from the annealing process and dried.
Finally, the planchet is struck. After striking, it becomes a coin and is no longer a planchet. Occasionally, a planchet will escape the mint without having been struck. This is a blank planchet error, and is usually worth a few dollars for modern coins. Occasionally, blank planchets can be rare and valuable, such is the case for Morgan Dollar blank planchets, although authentication and appraisal by a coin grading service is highly recommended for such pieces as they would be fairly easy to counterfeit.
1943 steel cents are U.S. one-cent coins that were struck in steel due to wartime shortages of copper. The Philadelphia, Denver, and San Francisco mints each produced these 1943 Lincoln cents. The unique composition of the coin has led to various nicknames, such as wartime cent, steel war penny, zinc cent and steelie. The 1943 steel cent features the same Victor David Brenner design for the Lincoln cent which had been in use since 1909.
Hammered coinage is the most common form of coins produced since the invention of coins in the first millennium BC until the early modern period of c. the 15th–17th centuries, contrasting to the cast coinage and the later developed milled coinage.
In numismatics, the term milled coinage is used to describe coins which are produced by some form of machine, rather than by manually hammering coin blanks between two dies or casting coins from dies.
Mint-made errors are errors during the minting process. Groups of coins with distinctive characteristics are known as varieties. The term variety applies to coins with both intended and unintended differences while the term error refers only to coins with unintended differences. Nevertheless, not all errors are varieties. Although there may be many identical examples of some errors, others are unique. For example, there may be many indistinguishable examples of coins with a specific die crack, while off-center strikes tend to be unique. Being unique does not mean that an error is valuable. Although no other coin may be similar to a coin with an off-center strike, off-center strikes happen often enough that buyers can choose from many examples each of which varies slightly from the other. Mint error coins can be the result of deterioration of the minting equipment, accidents or malfunctions during the minting process, or intentional interventions by mint personnel. Accidental error coins are perhaps the most numerous and in modern minting are usually very rare, making them valuable to numismatists. Intentional intervention by mint personnel does not necessarily include a deliberate attempt to create an error, but usually involves an action intended to improve quality that miscarries and creates error coins instead. Errors can be the result of defective planchets, defective dies or the result of mistakes made during striking. The planchet, die, and striking classification system happens to correspond with the mintmarks of the three largest U.S. mints, Philadelphia, Denver, and San Francisco. Not all errors fall neatly within the categories. Sometimes design elements are missing from coins because die crevices are filled with grease. Labels used to identify specific categories of errors sometimes describe the cause of the error. Other errors names describe what the viewer sees when looking at the coin while others have names that were adapted for use. The result is that some errors are known by multiple names. Filled die errors are also known as missing design element errors and as strike throughs. As is noted below under the discussion of missing design element coins, some errors have multiple causes. A rare error that sold for $5462.50 on Heritage Auctions in August 2010 is an undated U.S nickel struck on top of a 1960 5 centavos. Foreign coins struck on a U.S coin planchet or vice versa are very uncommon and hold a high value.
Die deterioration doubling (DDD) is a common form of mint-made error on many United States and Canadian coins that results from degradation of the die used to strike the coin.
A nickel is a five-cent coin struck by the United States Mint. Composed of cupronickel, the piece has been issued since 1866. Its diameter is 0.835 inches (21.21 mm) and its thickness is 0.077 inches (1.95 mm).
Proof coinage refers to special early samples of a coin issue, historically made for checking the dies and for archival purposes. Nowadays proofs are often struck in greater numbers specially for coin collectors (numismatists). Nearly all countries have issued proof coinage.
A mint is an industrial facility which manufactures coins that can be used as currency.
A fourrée is a coin, most often a counterfeit, that is made from a base metal core that has been plated with a precious metal to look like its solid metal counterpart; the term is derived from the French for "stuffed." The term is normally applied to ancient silver-plated coins such as the Roman denarius and Greek drachma, but the term is also applied to other plated coins.
The Eisenhower dollar was a one-dollar coin issued by the United States Mint from 1971 to 1978; it was the first coin of that denomination issued by the Mint since the Peace dollar series ended in 1935. The coin depicts President Dwight D. Eisenhower on the obverse, and on the reverse a stylized image honoring the 1969 Apollo 11 Moon mission based on the mission patch designed by astronaut Michael Collins. Both sides were designed by Frank Gasparro. It is the only large-size U.S. dollar coin whose circulation strikes contained no silver.
This glossary of numismatics is a list of definitions of terms and concepts relevant to numismatics and coin collecting, as well as sub-fields and related disciplines, with concise explanations for the beginner or professional.
In metallurgy and materials science, annealing is a heat treatment that alters the physical and sometimes chemical properties of a material to increase its ductility and reduce its hardness, making it more workable. It involves heating a material above its recrystallization temperature, maintaining a suitable temperature for an appropriate amount of time and then cooling.
The quarter eagle was a gold coin issued by the United States with a value of two hundred and fifty cents, or two dollars and fifty cents. It was given its name in the Coinage Act of 1792, as a derivation from the US ten-dollar eagle coin.
The Shield nickel was the first United States five-cent piece to be made out of copper-nickel, the same alloy of which American nickels are struck today. Designed by James B. Longacre, the coin was issued from 1866 until 1883, when it was replaced by the Liberty Head nickel. The coin takes its name from the motif on its obverse, and was the first five-cent coin referred to as a "nickel"—silver pieces of that denomination had been known as half dimes.
The three-dollar piece was a gold coin produced by the United States Bureau of the Mint from 1854 to 1889. Authorized by the Act of February 21, 1853, the coin was designed by Mint Chief Engraver James B. Longacre. The obverse bears a representation of Lady Liberty wearing a headdress of a Native American princess and the reverse a wreath of corn, wheat, cotton, and tobacco.
In numismatics, an overstrike describes a situation in which an existing coin rather than a blank is struck with a new design. This practice is now obsolete and generally occurred for two purposes. Overstriking was sometimes done for technical reasons when a first strike is unsatisfactory, or accidentally if the blank slips out of place or if the dies judder, resulting in a slight doubling of the design. However, sometimes old or worn coins were overstruck with new designs by later rulers or foreign states.
Minting, coining or coinage is the process of manufacturing coins using a kind of stamping, the process used in both hammered coinage and milled coinage. This "stamping" process is different from the method used in cast coinage.
US error coins are error coins produced by the US government. There are three categories of error coins as provided by the American Numismatic Association. Metal usage and striking errors referred to widely as planchet errors, die errors, and mint striking errors. This does not include the varieties that the US Mint has issued over the years.
A Schüsselpfennig, also Gehulchter Pfennig is so called due to the stamping technique which results in a concave, one-sided type of Pfennig coin. It was probably first minted in 1374 in the Palatinate. Small Schüsselpfennigs that had entered the Electorate of Saxony were referred to there as Näpfchenheller.
The Lilienpfennig was a type of Late Medieval pfennig from the German Free Imperial City of Strasbourg which was stamped on one side with the image of a fleur-de-lys.
