This article needs additional citations for verification .(April 2008) |
Siemens-Schuckert D.IV | |
---|---|
Siemens-Schuckert D.III on display at the Luftwaffe Museum at Gatow | |
Role | Fighter aircraft |
National origin | Germany |
Manufacturer | Siemens-Schuckert |
First flight | 1918 |
Introduction | 1918 |
Primary user | Germany |
Number built | 123 (by the end of the war) |
The Siemens-Schuckert D.IV was a late-World War I fighter aircraft from Siemens-Schuckert (SSW). It reached service too late and was produced in too few numbers to have any effect on the war effort.
Siemens-Schuckert's first production fighter aircraft was the Siemens-Schuckert D.I, which was based closely on the French Nieuport 17. Apart from the use of the Siemens-Halske Sh.I, a geared rotary engine in which the crankshaft and the propeller rotated in opposite directions, the D.I was in fact a fairly close copy of the Nieuport. By the time production D.Is appeared in 1917 however, the design was no longer competitive and after 95 had been built, production was cancelled, with the type serving mainly as an advanced trainer.
Development work on the Siemens-Halske Sh.I culminated in the Siemens-Halske Sh.III, which developed 160 PS (120 kW; 160 hp). The new engine was fitted to a series of original prototype designs from the SSW works, the D.II, D.IIa and D.IIb. These featured a short, round section fuselage designed to fit a larger engine, leading to a rather stubby-looking aircraft which pilots later referred to as the flying beer barrel. Flight tests started in June 1917, and while the aircraft did not have a very high top speed, they showed outstanding rates of climb. The only serious concern was the extremely long landing gear needed to keep the huge 2-bladed prop clear of the ground.
Three more prototypes were ordered, one D.IIe, with the original sized wings, and two D.IIc's, fitted with shorter and longer span wings. After completion in October 1917, the design proved promising and in December an order for twenty long-span D.IIc's was placed with a smaller 4-bladed propeller that allowed for shorter landing gear legs. Deliveries of these aircraft, now known as D.III, began in January and were followed by an additional order for thirty in February.
All fifty were delivered to front-line units in May, where they proved popular but after only 10 hours of service the engines started showing serious problems, overheating and seizing. Siemens blamed the problem on the Voltol-based oil that was used to replace scarce castor oil for lubricating the engine but the type was withdrawn from service and replaced by Fokker D.VIIs. When they were removed, Rudolf Berthold, commander of JG.II, noted that he wished "the Siemens fighter be made available again for front-line use as quickly as possible for, after elimination of the present faults, it is likely to become one of our most useful fighter aircraft".[ citation needed ]
A version of the Sh.III passed a 40-hour endurance test in June and the aircraft were cleared to return to service in July. In the meantime they had been upgraded with the addition of a new rudder, balanced ailerons and had the cowling cut-away for improved cooling. Some sources also claim that the original engines were replaced with the improved 200 PS (150 kW; 200 hp) Sh.IIIa engines. Another thirty new aircraft with these features were built and all eighty of the improved design entered service in home defense units where their climb rate made them excellent interceptors.
The short-span D.IIc prototype had been further refined and with a narrower 1.00 m (3 ft 3 in) chord upper and lower wing, using the Göttingen 180 airfoil. One wing was slightly longer than the other to counter the P-factor of its huge four-blade propeller. The port panels outboard of the struts were 1,110 mm (44 in) in length, while those on the starboard side were 1,040 mm (41 in) long. [1] The performance improved noticeably in top speed and in climb rate over the D.III. An order for this model, now known as the D.IV, was placed in March 1918 and additional orders were placed as the qualities of the design became known. Aircraft started reaching operational units in August but of the 280 ordered only 123 were completed by the end of the war, about half of those reaching operational units.
Although the short landing gear and limited prop clearance led to tricky landing, the plane was otherwise easy to fly. It had a very short take-off run and at heights above 4,000 m (13,000 ft) was faster and more manoeuvrable than the Mercedes-powered Fokker D.VII. Its most notable feature was its phenomenal rate of climb and extremely high service ceiling—it could reach 6,000 m (20,000 ft) in under 141⁄2 minutes. In 36 minutes it could reach 8,100 m (26,600 ft), about 1,200 m (3,900 ft) higher than the ceiling of the Fokker. Production of the D.IV continued after the cease-fire, while one example escaped to Switzerland where it operated from 1918 to 1922, and another was acquired by the Lithuanians, however it never flew in their service. One examples was used by the Belgians, being marked with the race number 22. With the signing of the Treaty of Versailles aircraft production in Germany was outlawed and the aircraft division of SSW disappeared. Siemens-Halske later reorganized into Bramo.
In May/June 1918 a sesquiplane, two bay derivative, the D.V participated in the Adlershof trials. Three were built. [2]
Data fromGerman Aircraft of the First World War [4]
General characteristics
Performance
Armament
The Fokker E.V was a German parasol-monoplane fighter aircraft designed by Reinhold Platz and built by Fokker-Flugzeugwerke. The E.V was the last Fokker design to become operational with the Luftstreitkräfte, entering service in the last months of World War I. After several fatal accidents due to wing failures, the aircraft was modified and redesignated Fokker D.VIII. Dubbed the Flying Razor by post-war pulp-fiction writers, the D.VIII had the distinction of scoring the last aerial victory of the war.
The Fokker E.IV was the final variant of the Eindecker fighter aircraft that was operated by Germany during World War I.
Siemens-Schuckert was a German electrical engineering company headquartered in Berlin, Erlangen and Nuremberg that was incorporated into the Siemens AG in 1966.
The Fokker D.I was a development of the D.II fighter. The D.I was also flown in Austro-Hungarian service as a fighter trainer aircraft under the designation B.III. Confusing the matter further, both the D.II and D.I arrived at the Front in German service at similar times, in July–August 1916. The main designer was Martin Kreutzer.
The Siemens-Halske Sh.III was an 11-cylinder, air-cooled counter rotary engine developed in Germany during World War I. The engine was a development of the earlier 9-cylinder Siemens-Halske Sh.I.
The Pfalz D.VIII was a German World War I fighter aircraft.
The Fokker V.7 was a prototype German fighter triplane of World War I, an attempt to improve upon the Dr.I by using the experimental Siemens-Halske Sh.III, double acting rotary engine.. To make use of the higher power and rpm, the aircraft had a four-bladed propeller of larger diameter than the Dr.I. This required longer landing gear. The rear fuselage had to be extended to compensate for the heavier engine. Four V.7 aircraft were built. The performance of the V.7 was outstanding, but the engine was not ready for service. The Fokker V.7/I was converted to a Dr.I.
The Fokker D.VI was a German fighter aircraft built in limited numbers at the end of World War I. The D.VI served in the German and Austro-Hungarian air services.
The Siemens-Schuckert D.I was a single-seat fighter built by Siemens-Schuckert Werke in 1916. It was a German copy of the French Nieuport 17 that was obsolete by the time it was available in numbers, so that it served mainly as an advanced trainer.
The Siemens-Schuckert D.III was a German single-seat fighter built by Siemens-Schuckert Werke. The D.III was a development of the earlier Siemens-Schuckert D.IIc prototype. The D.III was an (nearly) equal-span biplane powered by a 160 hp (119 kW) Siemens-Halske Sh.III bi-rotary engine. Idflieg placed an order for 20 aircraft in December 1917, followed by a second order of 30 aircraft in February 1918.
The Roland D.VI was a German fighter aircraft built at the end of World War I. It lost a fly-off to the Fokker D.VII, but production went ahead anyway as insurance against problems with the Fokker.
The Pfalz Dr.I was a German fighter prototype of World War I. Official interest in the potential of the triplane configuration for single-seat fighters prompted Pfalz to develop the Dr.I. It underwent initial testing in October 1917, and an initial batch of 10 aircraft were shipped to the Front and arrived in April 1918.
The Siemens-Schuckert E.I was a German fighter aircraft, manufactured by Siemens-Schuckert.
The Siemens-Schuckert D.VI was a single engine, single seat, parasol wing German fighter aircraft flown in 1919.
The Siemens-Schuckert DDr.I was a World War I German twin engine, push-pull configuration triplane fighter aircraft. Only one was built, crashing on its first flight.
The LFG Roland D.IX was a World War I German single seat fighter aircraft, a biplane powered by one of a new generation of powerful rotary engines. Three slightly different prototypes were built but there was no series production.
The LFG Roland D.XVI, initially designated the LFG Roland E.I, was a single-seat, single-engine, parasol wing German fighter aircraft flown close to the end of World War I. Only two were built.
The Siemens-Schuckert Dr.I was a German single seat triplane fighter aircraft first flown in 1917. Its development and that of a more powerful, uncompleted variant, was abandoned after a flight test programme.
The Siemens-Schuckert B was an unarmed German two seat reconnaissance biplane built early in World War I. A single example was delivered but soon lost.
The Pfalz Dr.II was a German triplane fighter prototype of World War I built by Pfalz Flugzeugwerke.