Sleeve valve (water)

Last updated

A sleeve valve is a device typically used in a water supply or distribution system when there is a need to reduce high pressure or throttle flow. The sleeve valve consists of a cylindrical gate (tube) which slides over an inner sleeve. The inner sleeve consists of a series of nozzles specifically sized and arranged to provide a solution to cavitation issues frequently encountered in throttling applications with other valve types. Because of its design, it minimizes cavitation. Cavitation that does occur in severe throttling conditions is directed from the valve down to center of the valve or pipe so that no erosion damage to the piping can take place.

Contents

Types

There are three main types of sleeve valves: inline, angle pattern and downflow pattern. Inline sleeve valve can be installed in the pipeline or at the end of the pipeline for free discharge. Inline sleeve valve have an inlet section which allows upstream media to flow into an outer annular area. The flow then takes a 90° turn through the sleeve and collides with flow from the opposite side dissipating the energy. The flow then travels downstream through an exit spool on the downstream end. The angle pattern sleeve valve is installed at a 90° bend in place of an elbow. Angle pattern sleeve valves employ a similar design as the inline sleeve valve by creating an outer annular area to contain the media and a sleeve with tapered nozzles to pass the flow. The difference is that the flow direction after passing through the sleeve changes by 90°. Downflow pattern sleeve valves are installed at the end of a pipeline and discharge into sumps, reservoirs, stilling wells or tanks. Unlike inline and angle pattern the discharge of a downflow pattern is outward and is not contained by the valve itself.

Advantages

Sleeve valves can operate for long periods of time over a high differential pressure across the valve. When a cavitation condition does exist the cavitation takes place surrounded by water. Unlike other valves, air is not necessary to control or suppress the cavitation. Because of this a single sleeve valve can replace several standard valves used in series. Sleeve valves can control flow and/or pressure over the entire stroke of the valve. Conventional control valves can typically control flow or pressure in the 20% to 80% range. Additionally, unlike conventional control valves the sleeve valve increases flow incrementally, i.e. 10% increase in stroke leads to a 10% increase in flow. Sleeve valves are adaptive to system or consumer requirements. The sleeve valve is designed to meet the requirements and allow for a wide range of variability of function. Most conventional control valves are designed to a specific set of conditions.

Disadvantages

Sleeve valve are generally more expensive than other types of control valves. Typically, sleeve valves are employed in situations where they would replace multiple valves in series or where frequent maintenance may be required, Sleeve valves need to be used where large debris is not expected in the system. As the orifice holes are relatively small, it is possible and likely that any trash in system will collect in front of sleeve or even in the nozzles themselves. Access ports are generally provided to access the valve interior for debris removal.

Installations

Typical installations for sleeve valves include the following: reservoir discharge, pump control, pressure regulation, turbine bypass, and tank level control.

Related Research Articles

<span class="mw-page-title-main">Cavitation</span> Low-pressure voids formed in liquids

Cavitation is a phenomenon in which the static pressure of a liquid reduces to below the liquid's vapour pressure, leading to the formation of small vapor-filled cavities in the liquid. When subjected to higher pressure, these cavities, called "bubbles" or "voids", collapse and can generate shock waves that may damage machinery. These shock waves are strong when they are very close to the imploded bubble, but rapidly weaken as they propagate away from the implosion. Cavitation is a significant cause of wear in some engineering contexts. Collapsing voids that implode near to a metal surface cause cyclic stress through repeated implosion. This results in surface fatigue of the metal, causing a type of wear also called "cavitation". The most common examples of this kind of wear are to pump impellers, and bends where a sudden change in the direction of liquid occurs. Cavitation is usually divided into two classes of behavior: inertial cavitation and non-inertial cavitation.

<span class="mw-page-title-main">Pump</span> Device that imparts energy to the fluids by mechanical action

A pump is a device that moves fluids, or sometimes slurries, by mechanical action, typically converted from electrical energy into hydraulic energy.

<span class="mw-page-title-main">Water hammer</span> Pressure surge when a fluid is forced to stop or change direction suddenly

Hydraulic shock is a pressure surge or wave caused when a fluid in motion, usually a liquid but sometimes also a gas is forced to stop or change direction suddenly; a momentum change. This phenomenon commonly occurs when a valve closes suddenly at an end of a pipeline system, and a pressure wave propagates in the pipe.

<span class="mw-page-title-main">Rocketdyne J-2</span> Rocket engine

The J-2 is a liquid-fuel cryogenic rocket engine used on NASA's Saturn IB and Saturn V launch vehicles. Built in the U.S. by Rocketdyne, the J-2 burned cryogenic liquid hydrogen (LH2) and liquid oxygen (LOX) propellants, with each engine producing 1,033.1 kN (232,250 lbf) of thrust in vacuum. The engine's preliminary design dates back to recommendations of the 1959 Silverstein Committee. Rocketdyne won approval to develop the J-2 in June 1960 and the first flight, AS-201, occurred on 26 February 1966. The J-2 underwent several minor upgrades over its operational history to improve the engine's performance, with two major upgrade programs, the de Laval nozzle-type J-2S and aerospike-type J-2T, which were cancelled after the conclusion of the Apollo program.

<span class="mw-page-title-main">Spillway</span> Structure for controlled release of flows from a dam or levee

A spillway is a structure used to provide the controlled release of water downstream from a dam or levee, typically into the riverbed of the dammed river itself. In the United Kingdom, they may be known as overflow channels. Spillways ensure that water does not damage parts of the structure not designed to convey water.

A propelling nozzle is a nozzle that converts the internal energy of a working gas into propulsive force; it is the nozzle, which forms a jet, that separates a gas turbine, or gas generator, from a jet engine.

This is a glossary of firefighting equipment.

<span class="mw-page-title-main">Centrifugal pump</span> Pump used to transport fluids by conversion of rotational kinetic energy

Centrifugal pumps are used to transport fluids by the conversion of rotational kinetic energy to the hydrodynamic energy of the fluid flow. The rotational energy typically comes from an engine or electric motor. They are a sub-class of dynamic axisymmetric work-absorbing turbomachinery. The fluid enters the pump impeller along or near to the rotating axis and is accelerated by the impeller, flowing radially outward into a diffuser or volute chamber (casing), from which it exits.

<span class="mw-page-title-main">Floodgate</span> Adjustable gate used to control water flow

Floodgates, also called stop gates, are adjustable gates used to control water flow in flood barriers, reservoir, river, stream, or levee systems. They may be designed to set spillway crest heights in dams, to adjust flow rates in sluices and canals, or they may be designed to stop water flow entirely as part of a levee or storm surge system. Since most of these devices operate by controlling the water surface elevation being stored or routed, they are also known as crest gates. In the case of flood bypass systems, floodgates sometimes are also used to lower the water levels in a main river or canal channels by allowing more water to flow into a flood bypass or detention basin when the main river or canal is approaching a flood stage.

A compressor map is a chart which shows the performance of a turbomachinery compressor. This type of compressor is used in gas turbine engines, for supercharging reciprocating engines and for industrial processes, where it is known as a dynamic compressor. A map is created from compressor rig test results or predicted by a special computer program. Alternatively the map of a similar compressor can be suitably scaled. This article is an overview of compressor maps and their different applications and also has detailed explanations of maps for a fan and intermediate and high-pressure compressors from a three-shaft aero-engine as specific examples.

A twincharger refers to a compound forced induction system used on some internal combustion engines. It is a combination of an exhaust-driven turbocharger and a mechanically driven supercharger, each mitigating the weaknesses of the other.

Choked flow is a compressible flow effect. The parameter that becomes "choked" or "limited" is the fluid velocity.

Artificial lift refers to the use of artificial means to increase the flow of liquids, such as crude oil or water, from a production well. Generally this is achieved by the use of a mechanical device inside the well or by decreasing the weight of the hydrostatic column by injecting gas into the liquid some distance down the well. A newer method called Continuous Belt Transportation (CBT) uses an oil absorbing belt to extract from marginal and idle wells. Artificial lift is needed in wells when there is insufficient pressure in the reservoir to lift the produced fluids to the surface, but often used in naturally flowing wells to increase the flow rate above what would flow naturally. The produced fluid can be oil, water or a mix of oil and water, typically mixed with some amount of gas.

A control valve is a valve used to control fluid flow by varying the size of the flow passage as directed by a signal from a controller. This enables the direct control of flow rate and the consequential control of process quantities such as pressure, temperature, and liquid level.

<span class="mw-page-title-main">Surge tank</span> Water storage device to smooth pressure variations

A Surge tank is a water storage device used as a pressure neutralizer in hydropower water conveyance systems in order to dampen excess pressure variance.

<span class="mw-page-title-main">Components of jet engines</span> Brief description of components needed for jet engines

This article briefly describes the components and systems found in jet engines.

<span class="mw-page-title-main">Instrumentation in petrochemical industries</span>

Instrumentation is used to monitor and control the process plant in the oil, gas and petrochemical industries. Instrumentation ensures that the plant operates within defined parameters to produce materials of consistent quality and within the required specifications. It also ensures that the plant is operated safely and acts to correct out of tolerance operation and to automatically shut down the plant to prevent hazardous conditions from occurring. Instrumentation comprises sensor elements, signal transmitters, controllers, indicators and alarms, actuated valves, logic circuits and operator interfaces.

<span class="mw-page-title-main">Spray (liquid drop)</span> Dynamic collection of drops dispersed in a gas

A spray is a dynamic collection of drops dispersed in a gas. The process of forming a spray is known as atomization. A spray nozzle is the device used to generate a spray. The two main uses of sprays are to distribute material over a cross-section and to generate liquid surface area. There are thousands of applications in which sprays allow material to be used most efficiently. The spray characteristics required must be understood in order to select the most appropriate technology, optimal device and size.

Steam turbine governing is the procedure of controlling the flow rate of steam to a steam turbine so as to maintain its speed of rotation as constant. The variation in load during the operation of a steam turbine can have a significant impact on its performance. In a practical situation the load frequently varies from the designed or economic load and thus there always exists a considerable deviation from the desired performance of the turbine. The primary objective in the steam turbine operation is to maintain a constant speed of rotation irrespective of the varying load. This can be achieved by means of governing in a steam turbine. There are many types of governors.

<span class="mw-page-title-main">Open channel spillway</span>

Open channel spillways are dam spillways that utilize the principles of open-channel flow to convey impounded water in order to prevent dam failure. They can function as principal spillways, emergency spillways, or both. They can be located on the dam itself or on a natural grade in the vicinity of the dam.

References