|In commission||1918–46 (USN)|
|Length||314 ft 4.5 in (95.82 m)|
|Beam||30 ft 11.25 in (9.43 m)|
|Draft||9 ft (2.74 m)|
|Speed||35.3 kn (65.4 km/h; 40.6 mph)|
|Complement||100 officers and enlisted|
|Notes||popularly known as Flush Deckers, Four Pipers, Four-stackers, 1200-ton type|
The Wickes-class destroyers were a class of 111 destroyers built by the United States Navy in 1917–19. Along with the 6 preceding Caldwell-class and 156 subsequent Clemson-classdestroyers, they formed the "flush-deck" or "four-stack" type. Only a few were completed in time to serve in World War I, including USS Wickes, the lead ship of the class.
While some were scrapped in the 1930s, the rest served through World War II. Most of these were converted to other uses; nearly all in U.S. service had half their boilers and one or more stacks removed to increase fuel and range or accommodate troops.Others were transferred to the British Royal Navy and the Royal Canadian Navy, some of which were later transferred to the Soviet Navy. All were scrapped within a few years after World War II.
The destroyer type was at this time a relatively new class of fighting ship for the U.S. Navy. The type arose in response to torpedo boats that had been developing from 1865, especially after the development of the self-propelled Whitehead torpedo.During the Spanish–American War, it was realized that a torpedo boat destroyer was urgently needed to screen the larger warships, so much so that a special war plans board headed by Theodore Roosevelt issued an urgent report pleading for this type of ship.
A series of destroyers had been built over the preceding years, designed for high smooth water speed, with indifferent results, especially poor performance in heavy seas and poor fuel economy.The lesson of these early destroyers was the appreciation of the need for true seakeeping and seagoing abilities. There were few cruisers in the Navy, which was a fleet of battleships and destroyers (no cruisers had been launched since 1908) so destroyers performed scouting missions. A report of October 1915 by Captain W. S. Sims noted that the smaller destroyers used fuel far too quickly, and that war games showed the need for fast vessels with a larger radius of action. As a result, the size of U.S. destroyer classes increased steadily, starting at 450 tons and rising to over 1,000 tons between 1905 and 1916. The increase in destroyer size has never stopped, with some US Arleigh Burke-classdestroyers now up to 10,800 tons full load, and the Zumwalt-classdestroyers at 14,564 tons full load. The need for high speed, economical cruising, heavy seas performance, and a high fuel capacity saw larger hulls, the inclusion of oil fuel, reduction geared steam turbines with cruising turbines, and increased fuel capacity.
With World War I then in its second year and tensions between the U.S. and Germany increasing, the U.S. needed to expand its navy. The Naval Appropriation Act of 1916 called for a navy "second to none," capable of protecting both the Atlantic and Pacific coasts. The Act authorized 10 battleships, 6 Lexington-class battlecruisers, 10 Omaha-class scout cruisers, and 50 Wickes-class destroyers.A subsequent General Board recommendation for further destroyers to combat the submarine threat resulted in a total of 267 Wickes- and Clemson-class destroyers completed. However, the design of the ships remained optimized for operation with the battleship fleet.
The requirements of the new design were high speed and mass production. The development of submarine warfare during World War I created a requirement for destroyers in numbers that had not been contemplated before the war. A top speed of 35 knots (65 km/h) was needed for operation with the Lexington battlecruisers and Omaha cruisers.
The final design had a flush deck and four smokestacks. It was a fairly straightforward evolution of the preceding Caldwell class. General dissatisfaction with the earlier "1,000 ton" designs (Cassin and Tucker classes) led to the fuller hull form of the "flush deck" type. Greater beam and the flush deck provided greater hull strength. In addition, the Wickes class had 26,000 horsepower (19,000 kW) (6,000 horsepower (4,500 kW) more than the Caldwell class), providing an extra 5 knots (9.3 km/h; 5.8 mph). The machinery arrangement of some of the Caldwells was used, with geared steam turbines on two shafts.
The extra power required an extra 100 tons of engine and reduction gears. The design included an even keel and nearly horizontal propeller shafts to minimize weight.
As construction was undertaken by ten different builders, there was considerable variation in the types of boilers and turbines installed to meet a guaranteed speed requirement. However, there were in essence two basic designs; one for the ships built by the Bethlehem Steel yards (including Union Iron Works) and another used by the remaining shipyards, which was prepared by Bath Iron Works.
The Wickes class proved to be short-ranged, and its bridge and gun positions were very wet. The fleet found that the tapered stern, which made for a nice depth charge deployment feature, dug into the water and increased the turning radius, thus hampering anti-submarine work.The Clemson class added 100 tons of fuel tankage to improve operational range, but the issue of range was solved only with the development of underway replenishment in World War II.
The main armament was the same as the Caldwell class: four 4-inch (102 mm)/50 caliber guns and twelve 21-inch (533 mm) torpedo tubes. While the gun armament was typical for destroyers of this period, the torpedo armament was larger than usual, in accordance with American practice at the time. A factor in the size of the torpedo armament was the General Board's decision to use broadside rather than centerline torpedo tubes. This was due to the desire to have some torpedoes remaining after firing a broadside, and problems experienced with centerline mounts on previous classes with torpedoes striking the gunwales of the firing ship. The Mark 8 torpedo was initially equipped, and probably remained the standard torpedo for this class, as 600 Mark 8 torpedoes were issued to the British in 1940 as part of the Destroyers for Bases Agreement.
Most ships carried a 3-inch (76 mm)/23 caliber anti-aircraft (AA) gun, typically just aft of the stern 4-inch gun. The original design called for two 1-pounder AA guns, but these were in short supply and the 3-inch gun was more effective. Anti-submarine (ASW) armament was added during World War I. Typically, a single depth charge track was provided aft, along with a Y-gun depth charge projector forward of the aft deckhouse.
The United States Congress authorized 50 destroyers in the 1916 Act. However, the realization of the scope of the U-boat campaign resulted in 111 being built. The ships were built at Bath Iron Works, Bethlehem Steel Corporation's Fore River Shipbuilding Company, Union Iron Works, Mare Island Navy Yard, Newport News Shipbuilding, New York Shipbuilding, and William Cramp & Sons. 267 Wickes and Clemson-class destroyers were built. This program was considered a major industrial achievement.Production of these destroyers was considered so important that work on cruisers and battleships was delayed to allow completion of the program. The first Wickes-class vessel was launched on 11 November 1917, with four more by the end of the year. Production peaked in July 1918, when 17 were launched - 15 of them on 4 July.
The program continued after the war ended: 21 of the Wickes class (and all but 9 of the Clemson class) were launched after the armistice on 11 November 1918. The last of the Wickes class was launched on 24 July 1919.This program left the U.S. Navy with so many destroyers that no new destroyers were built until 1932 (the Farragutclass).
111 Wickes-class destroyers were built.
Some of these ships are also referred to as Little class (52 ships), Lamberton class (11 ships), or Tattnall class (10 ships) to signify the yard that built them and to note the slight design differences from the Bath Iron Works ships. Some of these non-Bath Iron Works units were actually commissioned prior to the lead ship, Wickes.
A few Wickes class were completed in time for service in World War I, some with the battle fleet, some on convoy escort duty; none were lost. DeLong ran aground in 1921; Woolsey sank after a collision in 1921.
Many Wickes-class destroyers were converted to other uses, starting as early as 1920, when 14 were converted to light minelayers (hull classification symbol DM). Six of these were scrapped in 1932, and replaced by five additional conversions. Another four were converted to auxiliaries or transports at that time. Four Wickes-class DM conversions and four Clemson-class DM conversions survived to serve in World War II.During the 1930s, 23 more were scrapped, sold off, or sunk as targets. This was mostly due to a blanket replacement of 61 Yarrow-boilered destroyers 1930-31, as these boilers wore out quickly in service. Flush-deckers in reserve were commissioned as replacements.
Starting in 1940, many of the remaining ships were also converted. Sixteen were converted to high-speed transports with the designation APD. Eight were converted to destroyer minesweepers (DMS). Most ships remaining in service during World War II were rearmed with dual-purpose 3-inch (76 mm)/50 caliber guns for better anti-aircraft protection. The AVD seaplane tender conversions received 2 guns; the APD transport, DM minelayer, and DMS minesweeper conversions received 3 guns, and those retaining destroyer classification received 6. Also, half of the torpedo tubes were removed in those retained as destroyers; all torpedoes were removed from the others. Nearly all had half the boilers removed, for increased fuel and range or to accommodate troops, reducing their speed to 25 knots (46 km/h; 29 mph).
The low-angle Mark 9 4-inch guns removed from these ships were transferred to defensively equipped merchant ships for anti-submarine protection.
Ward had an eventful career. She was built in record time: her keel was laid on 15 May 1918, launched only 17 days later on 1 June 1918, and commissioned 54 days after that on 24 July 1918. She is credited with firing the first US shots of the attack on Pearl Harbor on 7 December 1941, sinking a Japanese midget submarine with gunfire before the air attack started. The sinking was uncertain until the submarine's wreck was discovered in 2002. As the high-speed transport APD-16, she was damaged beyond repair by a kamikaze attack on 7 December 1944, and was sunk after abandoning ship by gunfire from the destroyer O'Brien, commanded at the time by Ward's former CO from the Pearl Harbor attack.
Thirteen Wickes class were lost during World War II in U.S. service. The remainder were scrapped between 1945 and 1947.
Twenty-three Wickes-class destroyers were transferred to the Royal Navy, along with four to the Royal Canadian Navy, in 1940 under the Destroyers for Bases Agreement. Most of these ships were refitted much like the U.S. destroyers and used as convoy escorts, but some were used very little and were not considered worth refitting. Buchanan, renamed HMS Campbeltown, was disguised as a German vessel and expended as a blockship in the St Nazaire Raid. (A newer Buchanan that was involved in the Japanese surrender formalities was a later ship.) One further destroyer was sunk; the remainder were scrapped between 1944 and 1947.
In 1944 seven were transferred by Britain to the Soviet Navy, in place of Italian ships claimed by the USSR after Italy's surrender. These vessels all survived the war, and were scrapped between 1949 and 1952.
High-speed transports were converted destroyers and destroyer escorts used in US Navy amphibious operations in World War II and afterward. They received the US Hull classification symbol APD; "AP" for transport and "D" for destroyer.
The Clemson class was a series of 156 destroyers which served with the United States Navy from after World War I through World War II.
USS Kimberly (DD-80) was a Wickes-class destroyer built for the United States Navy during World War I.
USS Mahan (DD-102) was a Wickes-class destroyer, built for the United States Navy. Commissioned in 1918, Mahan was a flush deck destroyer, and the first ship to be named for Rear Admiral Alfred Thayer Mahan. Her main battery consisted of four 4-inch/50 caliber guns.
USS Burns (DD-171) was a Wickes-class destroyer built for the United States Navy during World War I.
Four destroyers in the United States Navy comprised the Cassin class. All served as convoy escorts during World War I. The Cassins were the first of five "second-generation" 1000-ton four-stack destroyer classes that were front-line ships of the Navy until the 1930s. They were known as "thousand tonners" for their normal displacement, while the previous classes were nicknamed "flivvers" for their small size, after the Model T Ford.
The Sampson-class destroyers served in the United States Navy during World War I. Commissioned in 1916 and 1917, the class was a modification of the O'Brien and Tucker classes, with the number of 21-inch (533 mm) torpedo tubes increased from four twin-mounts to four triple-mounts. The Sampsons were the final six ships of the 26 "thousand tonner" destroyers. They were the largest and most heavily armed of the "thousand tonners", and the subsequent "flush deck" classes differed mainly in hull design and the engineering plant.
The first USS McCook (DD-252) was a Clemson-class destroyer in the United States Navy. Entering service in 1919, the ship had a brief active life before being placed in the reserve fleet. Reactivated for World War II, the ship was transferred to the Royal Navy and then to the Royal Canadian Navy and renamed HMCS St. Croix. Assigned as a convoy escort in the Battle of the Atlantic, St. Croix was torpedoed and sunk on 20 September 1943.
USS Tingey (DD-272) was a Clemson-class destroyer in service with the United States Navy from 1919 to 1922. She was scrapped in 1936.
USS Case (DD-285) was a Clemson-class destroyer in service with the United States Navy from 1919 to 1930. She was scrapped in 1931.
USS Converse (DD-291) was a Clemson-class destroyer built for the United States Navy during World War I.
USS Percival (DD-298) was a Clemson-class destroyer built for the United States Navy during World War I.
USS Kidder (DD-319) was a Clemson-class destroyer in service with the United States Navy from 1921 to 1930. She was scrapped in 1931.
USS Chase (DD-323) was a Clemson-class destroyer built for the United States Navy during World War I.
USS Mullany (DD-325) was a Clemson-class destroyer built for the United States Navy during World War I.
USS Preston (DD-327) was a Clemson-class destroyer built for the United States Navy during World War I.
USS Lamson (DD-328) was a Clemson-class destroyer built for the United States Navy during World War I.
The Caldwell class was a class of six "flush deck" United States Navy destroyers built during World War I and shortly after. Four served as convoy escorts in the Atlantic; the other two were completed too late for wartime service. Two were scrapped during the 1930s, but four survived to serve throughout World War II, three of these in service with the Royal Navy under the Destroyers for Bases Agreement and the fourth as a high speed transport.
The Farragut-class destroyers were a class of eight 1,365-ton destroyers in the United States Navy and the first US destroyers of post-World War I design. Their construction, along with the Porter class, was authorized by Congress on 29 April 1916, but funding was delayed considerably. Limited to 1,500 tons standard displacement by the provisions of the London Naval Treaty of 1930, the ships were laid down beginning in 1932 and were completed by 1935. After 12 years since the last of the previous class of American destroyers was commissioned, the Farraguts were commissioned in 1934 and 1935.
|Wikimedia Commons has media related to Wickes class destroyers .|