Wrench size

Last updated

spanner (wrench) size and thread diameter of a hex nut Wrench size.svg
spanner (wrench) size and thread diameter of a hex nut
Pedalschluessel.png

Width across flats is the distance between two parallel surfaces on the head of a screw or bolt, or a nut, mostly for torque transmission by positive locking.

Contents

The term width across flats (AF) is used for the following forms:

Spanner

The width across flats indicates the nominal "size" of the spanner. It is imprinted on the spanners in millimeter (mm) values. Older British and current US spanners (wrenches) have inch sizes that are imprinted in intermediate sizes in fractions.

The two systems are in general not compatible, which can result in rounding of nuts and bolts (i.e. using a 13 mm spanner in place of a 12 in (12.7 mm)). There are some exceptions with a few sizes being close enough to interchange. This includes 19 mm and 34 inch (19.05 mm), which are interchangeable for most purposes. Sizes that may interchange, depending on the precision needed, include 2 mm (close to 564 inch (1.98 mm)), 4 mm (close to 532 inch (3.97 mm)) and 8 mm (close to 516 inch (7.94 mm)).

In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm. The tolerances necessary to make the tools usable are listed in documents like ASME/ANSI B18.2.2 for U.S. standards. [1] For instance, a bolt for a 1-inch nominal diameter thread might have flats that are 1.5 inches apart. The wrench for this bolt should have flats that are between 1.508 and 1.520 inches apart to allow for a little extra space between the nut flats and the bolt flats. This means that the wrench slips easily over the bolt, and can be removed easily as well.

Width across flats

Fastener terminology of hex nuts:
d: Nominal thread diameter
k: Wrench size (width across flats)
h: Thickness
e: Width across corners

e
=
2
3
3
[?]
k
[?]
1.154701
[?]
k
{\displaystyle e={\frac {2{\sqrt {3}}}{3}}\cdot k\approx 1.154701\cdot k} Hex-nut.png
Fastener terminology of hex nuts:
d: Nominal thread diameter
k: Wrench size (width across flats)
h: Thickness
e: Width across corners

The width across flats of the fastener (for example screws, nuts, clamps) is nominally the same as that on the tool. The table below shows dimensions of metric spanners for selected sizes of metric threads. [2] Note that with ISO 272 1982 the width across flats for M10, M12, M14 and M22 were changed from 17, 19, 22 and 32 mm respectively to the current standard.

Nominal thread diameter (mm)M2M4M5M6M8M10M12M16M20M24M30M36M42
Width across flats (mm)47810131618243036465565

Widths for bicycles

In addition to industry standards, there are special thread standards, such as the bicycle threads according to DIN 79012, a fastening thread on metric-inch size basis of the designation. Modern bicycle spokes carry the bike thread FG 2.3. [3] A spoke wrench matching the spoke nipple is needed.

See also

Related Research Articles

The Unified Thread Standard (UTS) defines a standard thread form and series—along with allowances, tolerances, and designations—for screw threads commonly used in the United States and Canada. It is the main standard for bolts, nuts, and a wide variety of other threaded fasteners used in these countries. It has the same 60° profile as the ISO metric screw thread, but the characteristic dimensions of each UTS thread were chosen as an inch fraction rather than a millimeter value. The UTS is currently controlled by ASME/ANSI in the United States.

<span class="mw-page-title-main">Fastener</span> Hardware device that mechanically joins or affixes two or more objects together

A fastener or fastening is a hardware device that mechanically joins or affixes two or more objects together. In general, fasteners are used to create non-permanent joints; that is, joints that can be removed or dismantled without damaging the joining components. Steel fasteners are usually made of stainless steel, carbon steel, or alloy steel.

<span class="mw-page-title-main">Washer (hardware)</span> Thin plate with a hole, normally used to distribute the load of a threaded fastener

A washer is a thin plate with a hole that is normally used to distribute the load of a threaded fastener, such as a bolt or nut. Other uses are as a spacer, spring, wear pad, preload indicating device, locking device, and to reduce vibration.

<span class="mw-page-title-main">Socket wrench</span> Lever with interchangeable socket heads to grip or turn a bolt or nut

A socket wrench is a type of spanner that uses a closed socket format, rather than a typical open wrench/spanner to turn a fastener, typically in the form of a nut or bolt.

<span class="mw-page-title-main">Screw thread</span> Helical structure used to convert between rotational and linear movement or force

A screw thread is a helical structure used to convert between rotational and linear movement or force. A screw thread is a ridge wrapped around a cylinder or cone in the form of a helix, with the former being called a straight thread and the latter called a tapered thread. A screw thread is the essential feature of the screw as a simple machine and also as a threaded fastener.

British Standard Whitworth (BSW) is an imperial-unit-based screw thread standard, devised and specified by Joseph Whitworth in 1841 and later adopted as a British Standard. It was the world's first national screw thread standard, and is the basis for many other standards, such as BSF, BSP, BSCon, and BSCopper.

British Association screw threads, or BA screw threads, are a set of small screw threads, the largest being 0BA at 6 mm diameter. They were, and to some extent still are, used for miniature instruments and modelling.

<span class="mw-page-title-main">Trapezoidal thread form</span> Screw thread profiles with trapezoidal outlines

Trapezoidal thread forms are screw thread profiles with trapezoidal outlines. They are the most common forms used for leadscrews. They offer high strength and ease of manufacture. They are typically found where large loads are required, as in a vise or the leadscrew of a lathe. Standardized variations include multiple-start threads, left-hand threads, and self-centering threads.

<span class="mw-page-title-main">Lug nut</span> Fastener, specifically a nut, used to secure a wheel on a vehicle

A lug nut or wheel nut is a fastener, specifically a nut, used to secure a wheel on a vehicle. Typically, lug nuts are found on automobiles, trucks (lorries), and other large vehicles using rubber tires.

The ISO metric screw thread is the most commonly used type of general-purpose screw thread worldwide. They were one of the first international standards agreed when the International Organization for Standardization (ISO) was set up in 1947.

<span class="mw-page-title-main">Computer case screws</span> Hardware used to secure parts of a PC to the case

Computer case screws are the hardware used to secure parts of a PC to the case. Although there are numerous manufacturers of computer cases, they have generally used three thread sizes. The Unified Thread Standard (UTS) originates from the United States, while the ISO metric screw thread is standardized worldwide. In turn, these thread standards define preferred size combinations that are based on generic units—some on the inch and others on the millimetre.

<span class="mw-page-title-main">Insert nut</span>

An insert nut provides a threaded socket for a wooden workpiece, similar to a wall anchor. Insert nuts are inserted into a pre-drilled hole by one of two means: screw in and hammer in. In both cases, the external protrusions bite into the wood, preventing the nut from either turning or pulling out.

<span class="mw-page-title-main">Screw</span> Type of fastener characterized by a thread wrapped around a cylinder core

A screw is an externally helical threaded fastener capable of being tightened or released by a twisting force (torque) to the head. The most common uses of screws are to hold objects together and there are many forms for a variety of materials. Screws might be inserted into holes in assembled parts or a screw may form its own thread. The difference between a screw and a bolt is that the latter is designed to be tightened or released by torquing a nut.

<span class="mw-page-title-main">Nut (hardware)</span> Type of fastener with a threaded hole

A nut is a type of fastener with a threaded hole. Nuts are almost always used in conjunction with a mating bolt to fasten multiple parts together. The two partners are kept together by a combination of their threads' friction, a slight stretching of the bolt, and compression of the parts to be held together.

Inserts are pins, bolts, screws, joints and other structures that are used to transfer localized loads to a composite panel or to join two composite panels together. Metallic inserts are commonly used in the aerospace and marine industries to attach objects to sandwich composite panels.

ISO 898 is an international standard that defines mechanical and physical properties for metric fasteners. This standard is the origin for other standards that define properties for similar metric fasteners, such as SAE J1199 and ASTM F568M. It is divided into five (nonconsecutive) parts:

<span class="mw-page-title-main">Bolt (fastener)</span> Threaded fastener with an external male thread requiring a matching female thread

A bolt is an externally helical threaded fastener that fastens objects with unthreaded holes together. This is done by applying a twisting force (torque) to a matching nut. The bolt has an external male thread requiring a matching nut with a pre-formed female thread. Unlike a screw, which holds objects together by the restricting motion parallel to the axis of the screw via the normal and frictional forces between the screw's external threads and the internal threads in the objects to be fastened, a bolt prevents that linear motion via the frictional and normal forces between the bolt's external threads and the internal threads of the matching nut, which can be tightened by applying a torque which moves the nut linearly along the axis of the bolt and compresses the objects to be fastened.

<span class="mw-page-title-main">Hex key</span> Driver for hexagonal socketed bolts or screws

A hex key is a simple driver for bolts or screws that have heads with internal hexagonal recesses (sockets).

<span class="mw-page-title-main">Preferred metric sizes</span> Metricated industry standards

Preferred metric sizes are a set of international standards and de facto standards that are designed to make using the metric system easier and simpler, especially in engineering and construction practices. One of the methods used to arrive at these preferred sizes is the use of preferred numbers and convenient numbers, such as the Renard series and 1-2-5 series, to limit the number of different sizes of components needed.

References

  1. "ASME B18.2.2-2022 Nuts for General Applications: Machine Screw Nuts; and Hex, Square, Hex Flange, and Coupling Nuts (Inch Series)".
  2. ISO 262:1998 ISO general purpose metric screw threads – Selected sizes for screws, bolts and nuts. International Organization for Standardization. 17 Dec 1998.
  3. Übersicht Gewinde am Fahrrad