Continuous Automatic Warning System

Last updated

The Continuous Automatic Warning System (CAWS) is a form of cab signalling and train protection system used in Ireland to help train drivers observe and obey lineside signals.

Contents

CAWS has been in use on Iarnród Éireann diesel trains since 1984. All NIR trains operating cross-border must also be fitted with CAWS. Coded track circuits, which form the basis of the system (see below), are installed on all Dublin Suburban and Intercity routes to Cork, Limerick, and Athlone and as far as the border on the Belfast line.

This system is of American origin, being originally supplied by US&S, then a division of Westinghouse Air Brake Company (WABCO). Current equipment is supplied by SASIB, a division of Alstom.

CAWS ADU on left, Acknowledge & Pre-departure test switches on right CAWS ADU.jpg
CAWS ADU on left, Acknowledge & Pre-departure test switches on right
CAWS/ATP pick-up coil CAWS coil.jpg
CAWS/ATP pick-up coil

Principles of operation

CAWS repeats the aspects shown by the lineside colour light signals on an aspect display unit (ADU) inside the driver's cab. The ADU continuously displays the aspect that was shown by the previous signal until updated about 350 metres before the next signal. The ADU then displays the aspect shown by that signal.

A change of ADU display to a less restrictive aspect (e.g., double yellow to green) is termed an upgrade, while a change to a more restrictive aspect (e.g., single yellow to red) is called a downgrade. Any change of ADU display is accompanied by an audible indication. A momentary audible ‘warble’ sound indicates an upgrade. A downgrade is accompanied by a continuous audible tone and the illumination of the Acknowledge Switch that must be pressed by the driver within seven seconds to prevent an automatic brake application occurring for one minute. This is not recoverable until the time has expired. Acknowledgement by the driver within the first seven seconds immediately silences the tone.

Technical details

The system consists of coded track circuits and on-board equipment. The coded track circuits transmit information about the signal aspect to the on-board equipment via two pick-up coils mounted on the front of the train, one over each rail.

The 50 Hz carrier signal is modulated with pulsed square wave codes according to the signal aspect. No code is generated for a red aspect. The system is therefore fail-safe, since loss of code will result in a red indication on the ADU.

In electrified DART areas, a different carrier frequency of 83.3 Hz is used to avoid interference from 50 Hz power line frequency. There is also a greater range of codes because they also control the automatic train protection on the DART units.

Diesel drivers have to select the appropriate carrier frequency when moving to or from an electrified area. "Carrier 1" (50 Hz) is used in non-electrified areas and "Carrier 2" (83.3 Hz) is used in electrified areas.

Advantages

Because CAWS is a continuous system, an upgrade can occur anywhere between signals. The driver may then accelerate in the knowledge that the signal ahead has changed to a better aspect, even though it may not yet be visible. Similarly, the driver can quickly act upon an unexpected downgrade, which may be the result of the signalman having returned the signal ahead to red in an emergency.

Disadvantages

Since CAWS is dependent on track circuits for its operation, it cannot be applied where axle counters are used for train detection (i.e., "mini-CTC" areas) without the additional cost.

CAWS does not act in the event of a signal being passed at danger if the Red aspect has been acknowledged.

See also

Related Research Articles

<span class="mw-page-title-main">Railway signal</span> Visual signal device for railway engineers

A railway signal is a visual display device that conveys instructions or provides warning of instructions regarding the driver's authority to proceed. The driver interprets the signal's indication and acts accordingly. Typically, a signal might inform the driver of the speed at which the train may safely proceed or it may instruct the driver to stop.

<span class="mw-page-title-main">Railway signalling</span> The principle of signals used to control railway traffic

Railway signalling (BE), or railroad signaling (AE), is a system used to control the movement of railway traffic. Trains move on fixed rails, making them uniquely susceptible to collision. This susceptibility is exacerbated by the enormous weight and inertia of a train, which makes it difficult to quickly stop when encountering an obstacle. In the UK, the Regulation of Railways Act 1889 introduced a series of requirements on matters such as the implementation of interlocked block signalling and other safety measures as a direct result of the Armagh rail disaster in that year.

<span class="mw-page-title-main">Automatic Warning System</span> Railway safety system

Automatic Warning System (AWS) is a railway safety system invented and predominantly used in the United Kingdom. It provides a train driver with an audible indication of whether the next signal they are approaching is clear or at caution. Depending on the upcoming signal state, the AWS will either produce a 'horn' sound, or a 'bell' sound. If the train driver fails to acknowledge a warning indication, an emergency brake application is initiated by the AWS. However if the driver correctly acknowledges the warning indication by pressing an acknowledgement button, then a visual 'sunflower' is displayed to the driver, as a reminder of the warning.

<span class="mw-page-title-main">Cab signalling</span> Railway safety system

Cab signaling is a railway safety system that communicates track status and condition information to the cab, crew compartment or driver's compartment of a locomotive, railcar or multiple unit. The information is continually updated giving an easy to read display to the train driver or engine driver.

<span class="mw-page-title-main">Automatische treinbeïnvloeding</span> Dutch system of automatic train protection

Automatische TreinBeïnvloeding or ATB is a Dutch train protection system first developed in the 1950s. Its installation was spurred by the Harmelen train disaster of 1962.

<span class="mw-page-title-main">Track circuit</span> Electrical device used to detect the presence of trains on rail tracks

A track circuit is an electrical device used to prove the absence of a train on rail tracks to signallers and control relevant signals. An alternative to track circuits are axle counters.

<span class="mw-page-title-main">Linienzugbeeinflussung</span> In-cab signalling and train protection system

Linienzugbeeinflussung is a cab signalling and train protection system used on selected German and Austrian railway lines as well as on the AVE and some commuter rail lines in Spain. The system was mandatory where trains were allowed to exceed speeds of 160 km/h (99 mph) in Germany and 220 km/h (140 mph) in Spain. It is also used on some slower railway and urban rapid transit lines to increase capacity. The German Linienzugbeeinflussung translates to continuous train control, literally: linear train influencing. It is also called linienförmige Zugbeeinflussung.

<span class="mw-page-title-main">Punktförmige Zugbeeinflussung</span> German railway signal system

PZB or Indusi is an intermittent cab signalling system and train protection system used in Germany, Austria, Slovenia, Croatia, Romania, Israel, Serbia, on two lines in Hungary, on the Tyne and Wear Metro in the UK, and formerly on the Trillium Line in Canada.

<span class="mw-page-title-main">UK railway signalling</span> Rail traffic control systems used in the United Kingdom

The railway signalling system used across the majority of the United Kingdom rail network uses lineside signals to control the movement and speed of trains.

Australian railway signalling varies between the States of Australia, because the individual States are responsible for the railway systems within their own borders, with, historically, no need to co-ordinate between states except at the boundaries.

<span class="mw-page-title-main">Transmission Voie-Machine</span> Railway cab signaling technology used on high-speed rail

Transmission Voie-Machine is a form of in-cab signalling originally deployed in France and is mainly used on high-speed railway lines. TVM-300 was the first version, followed by TVM-430.

RS4 Codici is a train protection system used in Italy. The term is an abbreviation of Ripetizione Segnali a 4 codici.

Sistema di Controllo della Marcia del Treno (SCMT) is a discontinuous train cab signalling system used in Italy. It shares many features with the Ripetizione Segnali (RS) system, the two systems co-existing and working together. The main purpose of SCMT is to control the respect of the speed limit imposed by the signal aspect and the line condition.

Blocco automatico a correnti codificate is a signalling block system used in Italy on railway lines using 3 kV DC electrification.

<span class="mw-page-title-main">Cab Secure Radio</span> British Rail driver/signaller communication system

Cab Secure Radio (CSR) was an in-cab analogue radiotelephone system formerly used on parts of the British railway network. Its main function was to provide a secure speech link between the train driver and the signaller which could not be overheard by other train drivers. In areas where CSR was used, it had to be the primary method of communication between driver and signaller, always being used in preference to the signal post telephone. CSR was replaced by the GSM-R digital system, forming the initial phase of rollout of ERTMS throughout the UK.

<span class="mw-page-title-main">Pulse code cab signaling</span> Railway track status technology

Pulse code cab signaling is a form of cab signaling technology developed in the United States by the Union Switch and Signal corporation for the Pennsylvania Railroad in the 1920s. The 4-aspect system widely adopted by the PRR and its successor railroads has become the dominant railroad cab signaling system in North America with versions of the technology also being adopted in Europe and rapid transit systems. In its home territory on former PRR successor Conrail owned lines and on railroads operating under the NORAC Rulebook it is known simply as Cab Signaling System or CSS.

The first railway signalling in Greece was installed on the Athens–Piraeus Railway at the turn of the 20th century, when semaphores and boards were added with the line's electrification. Other Greek trains at that time were controlled by signals given manually by station masters. During World War II, German occupation forces installed mechanically operated semaphore signals at the entrance to all stations, with some light signals at busy stations. Modern signalling is provided through colour light signals. Radio communication between train stations and drivers was introduced in 1973 and digital communication is an ongoing present-day introduction.

Belgian railway signalling is the signalling in effect on the Belgian rail network currently operated by Infrabel.

<span class="mw-page-title-main">LS 90</span> Czech and Slovak railway signalling system

LS is a cab signalling and train protection system used on the main lines of Czech and Slovak railways. This system continuously transmits and shows a signal aspect of the next main signal in the driver's cabin while also periodically checking the driver's vigilance when their attention is required.

<span class="mw-page-title-main">ALSN</span> Soviet and Russian automatic train signaling system

ALSN is a train control system used widely on the main lines of the ex-Soviet states. It uses modulated pulses inducted into rails similar to the Italian RS4 Codici and American Pulse Code Cab Signaling. On high-speed lines the variant ALS-EN (АЛС-ЕН) is used which takes advantage of a double phase difference modulation of the carrier wave.

References