The 14"/50 caliber railway guns were spare US Navy Mk 4 14 inch/50 caliber guns mounted on railway cars and operated by US Navy crews in France in the closing months of World War I.
In 1917 the Allies were losing an artillery duel against heavy German guns along the Flanders coast in Belgium, and the important French Channel port of Dunkirk was being shelled by 38 cm German guns sited in Belgium at a range of over 24 miles (39km). There was also a need for the Allies to bombard strategic targets in the German rear areas to hinder German capability to stage attacks. The largest Allied guns in the area were British 12-inch Mk X guns which were outranged.
Mark I Navy railway mount
Mk I gun car of the type that served in France
Upon its entry into the war, the US chose its largest and longest-ranged available naval gun to fill the gap—the 14"/50 caliber Mk 4 gun with a muzzle velocity of 2800 feet per second. The new 16-inch gun would have been preferable, but it was not yet available in numbers; spare 14-inch guns kept for the active fleet were used instead.[2]
Baldwin Locomotive Works delivered five trains for the United States Navy during April and May 1918. Each train transported and supported a 14"/50 caliber Mk 4 gun[3] mounted on a rail carriage with four 6-wheel bogies.
Arrival in France
There was some doubt as to whether the Flanders coast and French Channel ports were now safe Allied ports, following the German spring offensive successes in March and April 1918 which brought those areas within German artillery and attack range. The guns were therefore diverted from the British zone in the north to further south,[4] to the port of St. Nazaire, to avoid the risk of having such valuable assets captured or destroyed.
Each battery composed of a locomotive, gun car, ammunition cars, supporting equipment cars, and accommodation cars for the crew. Each train was under the command of a United States Navy lieutenant, and under overall command of Rear Admiral Charles Peshall Plunkett. After delivery by ship, these trains were assembled in St. Nazaire in August.[5]
Operation
Mk I gun car with pit prepared, ready for firing
Before a gun arrived at a firing position, a curved length of track was laid at a position calculated suitable for firing at a specific target, and a pit 9 feet (2.7m) deep,[6] involving the removal of 103 cubic yards (79m3) of earth was dug, between the rails into which the gun recoiled 44 inches (1.1m).[7] Supports were also embedded in this pit connected to the gun mounting, to transmit remaining recoil energy directly to the ground and avoid placing excessive vertical strain on the gun car (and, through it, the track) and prevent it from moving backwards. In fact, by late 1918 the French had already constructed many such curved spurs (épis) for their own guns and hence the US guns were often able to re-use these.[8]
The gun car was positioned over the pit, the wheels were locked and the platform was locked into position with gun mount and car's weight shifted from the trucks (bogies) directly to the ground by jacks and lifting screws. The rails were removed from above the pit because the gun breech was too wide to pass between them.[9] The gun could elevate up to 43°, which gave it a maximum range of 42,000 yards (23.8 miles/38.4km), and could be traversed 2.5° left and right of center. Any greater change of direction required the gun to be moved forward or backward along its curved track and a new recoil pit dug. The gun used the standard naval gun mounting and recoil system, with the addition of a pneumatic system to assist the runout springs to return the gun to firing position after recoil at the higher maximum elevation of 43° compared to maximum 30° in naval use.[10]
A major disadvantage of the Mark I mount was that the weight was distributed forward, placing weight on the leading axles that was above the normally allowable weight for French railways, and also caused axle bearings to overheat at any speed over 5–10mph. The armored enclosed gun house lacked ventilation and caused condensation to form, which promoted rusting. The necessity to excavate a recoil pit was also not acceptable as a long-term solution of recoil control. Hence the Mark I, while functioning as designed, was seen as only a compromise measure necessitated by wartime time constraints.[11]
Combat service
Map showing firing locations and targets in France, 1918
The guns served to support General Pershing's army offensive in the Meuse-Argonne sector of the Western Front in France. They operated as single-gun batteries designated Battery 1 to Battery 5. Battery 2, commanded by Lieutenant (JG) E. D. Duckett, US Navy, had the distinction of being the first all-US gun (crew, gun, and ammunition) to fire in action on the Western Front. On 6 September 1918 they fired from the forest of Compiegne at the important German railway center of Tergnier in support of an Allied attack.[12]
The guns were used to target key infrastructure deep behind the German lines, such as railway junctions and other lines of communication and concentration, typically only opening fire after an Allied attack had begun to avoid giving the Germans any warning of Allied intentions.[13]
They fired 782 shells on 25 separate active days on the Western Front at ranges between 27 and 36 kilometers.[14] This equated to an average of 156 rounds per gun, which was approximately half the 300 rounds expected life of these guns before they would need refurbishment. The guns were only fired for specific strategic purposes to conserve barrel life, with smaller guns being used whenever possible. Hence on many days they remained inactive or were being moved.
The last shot was fired by Battery 4 at 10:57:30a.m. on 11 November 1918, timed to land just before the scheduled Armistice at 11 a.m.[15]
Mark I Army railway mount
The US Army ordered three units identical to the Navy Mark I mountings in May 1918 and another three in July 1918, also from Baldwin Locomotive Works. They were all completed by 20 September 1918 but the war ended before they were required to be shipped to France.[16]
Mark II Navy railway mount
Mk II mount
The new Mark II gun car developed during 1918 carried the same 14"/50 caliber Mk 4 gun but addressed the problem areas: it dispensed with the armored gun house, with gunners working in the open; the weight was more evenly spread over 20 axles instead of 12; the French system of rolling recoil was adopted, in which the gun was mounted higher to allow full recoil at maximum elevation without striking the ground and the car rolled back 30–40 feet after firing to absorb remaining recoil. This made it possible to fire the gun along any part of its curved track without any prior preparation, with elevation up to 40°. After firing, the gun car used a winch mounted at the front, connected to a strong point in the ground in front, to pull itself back to its firing position. World War I ended before the Mark II entered service, and it was used for coastal defense in the US.
↑ Five Mk I units were supplied to the Navy and were in action in France in 1918; six Mk I units were supplied to the Army late in 1918 and were not sent to France; five Mk II units were ordered in October 1918, three were canceled, and the first of the two completed was tested in August 1919. Earle 1920, pages 192, 197–200
↑ "Though it had been planned to ship the guns to the British transportation centers [in the northern Channel ports], conditions in France had so changed, owing to the threatening of the Channel ports by the Germans, that this plan seemed too risky, and Gen. Pershing was therefore consulted as to the cooperation of the batteries with the [US] Army [i.e. in the French frontline sectors]. Gen. Pershing replied on May 23, requesting shipment... to France without delay". See Breck (1922), p. 7.
↑ Many, Seymour B. (April 1965). "He Made No Complaint". United States Naval Institute Proceedings: 53.
↑ The pit was not required when firing at elevations up to 15°, where remaining recoil energy was absorbed by allowing the gun car to roll backwards until stopped by its brakes; but as the guns were never fired at the relatively short ranges achieved with such low elevation this was irrelevant. See Breck (1922), pp. 23–24
Willcox, Cornélis De Witt, and Edwin Roy Stuart (1918): The International Military Digest Annual for 1917. Cumulative Digest Corporation, New York. pp. 169–170.
TM 9-2300 standard artillery and fire control material. dated 1944
"Battleships on Wheels"Popular Science Monthly, January 1928, pp.16–18, 123–125, author was the US Navy admiral in charge of World War I 14-inch naval railroad cannon program.
A railway gun, also called a railroad gun, is a large artillery piece, often surplus naval artillery, mounted on, transported by, and fired from a specially designed railway wagon. Many countries have built railway guns, but the best-known are the large Krupp-built pieces used by Germany in World War I and World War II. Smaller guns were often part of an armoured train. Only able to be moved where there were good tracks, which could be destroyed by artillery bombardment or airstrike, railway guns were phased out after World War II.
The 16 inch gun M1919 (406 mm) was a large coastal artillery piece installed to defend the United States' major seaports between 1920 and 1946. It was operated by the United States Army Coast Artillery Corps. Only a small number were produced and only seven were mounted; in 1922 and 1940 the US Navy surplussed a number of their own 16-inch/50 guns, which were mated to modified M1919 carriages and filled the need for additional weapons.
The QF 4.7-inch Gun Mks I, II, III, and IV were a family of British quick-firing 4.724-inch (120 mm) naval and coast defence guns of the late 1880s and 1890s that served with the navies of various countries. They were also mounted on various wheeled carriages to provide the British Army with a long range gun. They all had a barrel of 40 calibres length.
The British Ordnance BL 9.2 inch gun on truck, railway mounted a variety of surplus 9.2 inch naval guns, together with the custom-designed Mk XIII railway gun, on various railway platforms to provide mobile long-range heavy artillery on the Western Front in World War I. Mk XIII remained in service for British home defence in World War II.
The British Ordnance BL 12 inch gun Mk IX on truck, railway mounted surplus 12 inch Mk IX W naval guns, manufactured by Woolwich Arsenal in 1906, on various railway platforms to provide mobile long-range heavy artillery for the British Army on the Western Front in World War I.
The QF 6-inch 40 calibre naval gun (Quick-Firing) was used by many United Kingdom-built warships around the end of the 19th century and the start of the 20th century.
The Ordnance QF Hotchkiss 6 pounder gun Mk I and Mk II or QF 6 pounder 8 cwt were a family of long-lived light 57 mm naval guns introduced in 1885 to defend against new, small and fast vessels such as torpedo boats and later submarines. There were many variants produced, often under license which ranged in length from 40 to 58 calibers, but 40 caliber was the most common version.
Ordnance BL 14-inch gun on truck, railway were 2 British 14-inch Mk III naval guns mounted on railway carriages, used on the Western Front in 1918. The guns had a very brief service life and were scrapped in 1926, but their railway carriages were re-used for mounting guns in World War II.
The 14"/50 caliber gun was a naval gun mounted on New Mexico and Tennessee-class battleships. These ships also featured the first "three-gun" turrets, meaning that each gun in each turret could be "individually sleeved" to elevate separately. The 14"/50 caliber guns were designated as Mark 4 and 6, with later versions known as Mark 7, 11, and B. These guns were more powerful than the main gun mounted on the previous three classes of US battleships, the 14"/45 caliber gun.
The 17 cm SK L/40 i.R.L. auf Eisenbahnwagen "Samuel" was a German railroad gun used in World War I.
The 38 cm SK L/45 "Max", also called Langer Max was a German long-range, heavy siege and coast-defense gun used during World War I. Originally a naval gun, it was also adapted for land service when it became clear that some of the ships for which it was intended would be delayed and that it would be very useful on the Western Front.
The 16"/50 caliber Mark 2 gun and the near-identical Mark 3 were guns originally designed and built for the United States Navy as the main armament for the South Dakota-class battleships and Lexington-class battlecruisers. The successors to the 16"/45 caliber gun Mark I gun, they were at the time among the heaviest guns built for use as naval artillery.
The 14-inch M1920 railway gun was the last model railway gun to be deployed by the United States Army. It was an upgrade of the US Navy 14"/50 caliber railway gun. Only four were deployed; two in the Harbor Defenses of Los Angeles and two in the Panama Canal Zone, where they could be shifted between the harbor defenses of Cristobal (Atlantic) or Balboa (Pacific).
The 8-inch Navy gun Mk.VI M3A2 on railway mount M1A1 was a World War II improved replacement for the World War I-era 8-inch M1888 gun and was used by the US Army's Coast Artillery Corps in US harbor defenses. The guns were also mounted in fixed emplacements on the barbette carriage M1A1. These guns were US Navy surplus 8"/45 caliber guns from battleships scrapped under the 1922 Washington Naval Treaty. Mark VI was the Navy designation. The Army designation for this gun was "8-inch Navy gun Mk.VI M3A2".
The 8-inch gun M1888 (203 mm) was a U.S. Army Coast Artillery Corps gun, initially deployed 1898–1908 in about 75 fixed emplacements, usually on a disappearing carriage. During World War I, 37 or 47 of these weapons were removed from fixed emplacements or from storage to create a railway gun version, the 8-inch Gun M1888MIA1 Barbette carriage M1918 on railway car M1918MI, converted from the fixed coast defense mountings and used during World War I and World War II.
The 10-inch Gun M1895 (254 mm) and its variants the M1888 and M1900 were large coastal artillery pieces installed to defend major American seaports between 1895 and 1945. For most of their history they were operated by the United States Army Coast Artillery Corps. Most were installed on disappearing carriages, with early installations on barbette mountings. All of the weapons not in the Philippines were scrapped during World War II. Two of the surviving weapons were relocated from the Philippines to Fort Casey in Washington state in the 1960s.
The 7"/44 caliber gun Mark 1 and 7"/45 caliber gun Mark 2 were used for the secondary batteries of the United States Navy's last generation of pre-dreadnought battleships, the Connecticut-class and Mississippi-class. The 7-inch (178 mm) caliber was considered, at the time, to be the largest caliber weapon suitable as a rapid-fire secondary gun because its shells were the heaviest that one man could handle alone.
The Obusier de 370 modèle 1915 à berceau was a French Railroad Gun that saw action during the First World War and Second World War.
The Obusier de 400 Modèle 1915/1916 were French railway howitzers that saw action during the First World War and World War II. The mle 1915/1916 was the largest caliber railway howitzers in service with the French Army during the First World War.
The Canon de 305 modèle 1893/96 à berceau was a French railroad gun that saw action during the First and Second World Wars.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
