VHF transmitter T-23/ARC-5 and HF transmitter T-20/ARC-5 on rack MT-71/ARC-5.
The AN/ARC-5 Command Radio Set is a series of radio receivers, transmitters, and accessories carried aboard U.S. Navy aircraft during World War II and for some years afterward. It is described as "a complete multi-channel radio transmitting and receiving set providing communication and navigation facilities for aircraft. The LF-MF-HF components are designed to transmit and receive voice, tone-modulated, and continuous wave (cw) signals."[1]:1 Its flexible design provided AMradiotelephone voice communication and Modulated continuous wave (MCW) and Continuous wave (CW) Morse code modes, all of which are typical capabilities in other Navy aircraft communication sets of the period. It was an improvement of the Navy's ARA/ATA command set. Similar units designated SCR-274-N were used in U.S. Army aircraft. The Army set is based on the ARA/ATA, not the later AN/ARC-5. The ARA/ATA and SCR-274-N series are informally referred to as "ARC-5", despite small differences that render all three series incompatible. Like the AN/ARC-5, the ARA/ATA and SCR-274-N had AM voice communication and two-way MCW and CW Morse code capability.[1]
The AN/ARC-5 command set was used by the US Navy from the latter part of World War II into the post-war era. It was fitted in many different aircraft types for communication between aircraft, navigation, and communication back to base. Units were available that covered much of the MF, HF, and VHF spectrum. Despite the use of octal basevacuum tubes, they were compact, rugged and light weight. Many became surplus after the war and were often converted for amateur radio use. The term 'ARC-5', while correctly applied to the AN/ARC-5 series, has also come to be a generic, though incorrect, term for the ARA/ATA and SCR-274-N command set units, including those designed by the Aircraft Radio Corporation in the late 1930s.[2]
The antecedent of the AN/ARC-5 system was the U.S. Navy's ARA/ATA system, initially deployed in 1940. The designations ARA and ATA are a pre-World War II Navy equipment nomenclature. The major units of the ARA are five receivers covering 0.19 to 9.1MHz, each unit with its own dynamotor power supply. The major units of the ATA are five transmitters covering 2.1 to 9.1MHz, using a common transmitter dynamotor/screen modulator unit. Most units were made by the Aircraft Radio Corporation (USN manufacturer's code CBY). Many units were also made by Stromberg-Carlson (USN manufacturer's code CCT).
To equip US Army Air Corps planes, the US Army adopted in 1941 a reduced set of radios from the ARA/ATA range. Designated SCR-274-N, these Army radios were electrically almost identical to their ARA/ATA counterparts, except for receiver output and modulator sidetone audio transformer output impedance. Structurally and in appearance, they were virtually identical except for most later units being left unpainted aluminum in contrast to the black wrinkle finish of the Navy sets. The designation SCR-274-N is a pre-World War II Army equipment nomenclature. The Army never acquired the ARA 1.5 to 3.0MHz receiver, nor the ATA 2.1 to 3.0MHz transmitter. Initially, it did not acquire the 3.0 to 4.0MHz transmitter, nor the 0.52 to 1.5MHz receiver, but the need to communicate on the common civil airfield frequency of 3.105MHz plus the anticipated USAAF use of the AN/ARR-1 homing adapter (see below) compelled adding these units to the SCR-274-N. Early Army units were made by Aircraft Radio Corporation, but the vast majority was made by Western Electric, plus a few by Colonial Radio and others.
In late 1943, the U.S. Navy fielded an improved and more flexible set of its ARA/ATA radios under the new Joint Army-Navy (JAN) nomenclature of AN/ARC-5. Structurally and in appearance, the AN/ARC5 series is almost identical to the former units but both receivers and transmitters are somewhat different electrically. A receiver and transmitter were added that provide four-channel crystal-controlled VHF-AM operation, along with a rarely encountered set of transmitters that provide coverage of 0.5 to 2.1MHz.
The main units of both the Navy and the Army systems were usually installed in three-receiver racks and two-transmitter racks. Units not in service could be stored on board the aircraft, just as one would store tuning units of other types of radio equipment.
Specifications
The following is a table of ARA/ATA, SCR-274-N, and AN/ARC-5 major components that could comprise a typical three-receiver, two-transmitter installation, with other configurations also being possible. In addition, several miscellaneous components are listed. A blank in the component ID column indicates that no equivalent unit existed for that system. A.R.C. refers to Aircraft Radio Corporation.[3]:3
(*) A (basic model) or B (1st revision). (†) No letter (basic model) or A (revision). (‡) A (basic model) or AM (field modified to remove vacuum capacitor).
LF/MF/HF receivers all use an almost identical 6-tube superhet design: r.f. amplifier (12SK7), converter (12K8), two i.f. stages (two 12SK7's(4), or 12SK7/12SF7(5)), diode detector/BFO (12SR7), and one audio stage (12A6). Transmitters use four tubes: 1626 oscillator, two 1625 finals, and 1629 magic-eye tuning. The latter allows a check of the dial calibration by giving a visual indication, viewable by raising a small cover, when the oscillator's frequency matches that of an internal crystal. (4)ARA and SCR-274-N. (5)AN/ARC-5.
Compatibility between systems
Audio frequency receiver output and modulator sidetone impedance for the ARA/ATA and the AN/ARC-5 is 300 to 600 ohms. In the SCR-274-N "-A" version, the receiver and modulator impedance is 4000 ohms, while "-B" and later version units have a 250 ohm tap on the AF transformers which can be connected.
ARA/ATA units and equivalent SCR-274-N units are interchangeable between systems, aside from audio impedance differences. However, AN/ARC-5 units generally are not interchangeable with the units of the earlier systems.
In contrast to ARA and SCR-274-N receivers, all AN/ARC-5 receivers have automatic volume control and a modified tube complement. The AN/ARC-5 navigation receivers have terminals and a switch to connect a DU-series direction finding loop to the receiver, and have a special audio line for an MX-19/ARC-5 adapter to allow the receiver to serve as an LF/MF localizer for the Navy's short-lived AN/ARN-9 Air-Track (related to ZA, ZAX) instrument landing system. These two capabilities were rarely if ever utilized. Otherwise, equivalent receivers of all three systems can interchange as a unit.
Few transmitter components of the AN/ARC-5 are interchangeable with ATA or SCR-274-N equivalent units. Mechanically, the transmitter rear power connector is slightly different, so inserting the wrong transmitter in a rack can damage either the rack or the transmitter power connector. Electrically, AN/ARC-5 transmitters use high-level final amplifier plate modulation, and the output tank circuit is shunt high voltage fed. The two earlier systems use less effective screen modulation, and the output circuit is series high voltage fed. The only electrical components of the AN/ARC-5 transmitter system that are interchangeable with the earlier systems are the dynamotor and the antenna relay.
Unlike earlier systems, none of the AN/ARC-5 control boxes have audio jacks for the microphone, headphone, or key. A separate jack box is used instead. AN/ARC-5 transmitter control boxes contain no Morse key.
Homing adaptors and VHF
The broadcast band receiver in all of these command sets is intended to host a homing adapter for the Navy ZB/YE homing system. The homing adapter demodulates a signal near 246MHz that is modulated with a broadcast band carrier. The output is sent to the broadcast band receiver tuned to the modulating frequency to further demodulate the carrier for voice messages or for a Morse code letter indicating to the pilot his bearing from the homing transmitter. All broadcast band receivers came with a power adapter to supply power to the homing adapter. The adapter under the Navy nomenclature system is the ZB-series. The identical unit under JAN nomenclature is the AN/ARR-1. This system was used by both the Navy extensively and the Army much less so. To put the system into operation on the aircraft, the beacon band receiver would be replaced in the rack by the broadcast band receiver. The antenna post is connected to the output of the homing adapter, and a power cable is connected from the homing adapter to the broadcast band receiver. The normal control that had been used for the beacon band receiver also serves this homing system without further reconfiguration.
Western Electric developed the AN/ARR-2, an all-in-one homing receiver that replaced the broadcast band receiver and external homing adapter and had other enhancements as well. The R-4A/ARR-2 uses the same dynamotor as the AN/ARC-5 sets, fits in the same racks, and can be controlled by special AN/ARC-5 control boxes. The AN/ARR-2 replaced the earlier R-24/ARC-5 and R-1/ARR-1 combo in AN/ARC-5 installations.
Western Electric developed a four-channel crystal-controlled VHF-AM receiver and transmitter for the U.S. Army's SCR-274-N system. The Army did not adopt these VHF components to any extent because of the move to a common British/American VHF capability in the form of the Bendix SCR-522 VHF-AM set. That remained Army policy until the arrival of the AN/ARC-3. The Navy adopted modified versions of the Western Electric units as the R-28/ARC-5 receiver and T-23/ARC-5 transmitter. The T-126/ARC-5 is a late variant of the T-23 which allowed the four channels to be grouped in a 100 to 146MHz tuning range, smaller than the T-23's.
Typical configuration
SCR-274N Command Radio
A typical installation of ARA/ATA or SCR-274-N sets would consist of a 3.0 to 6.0MHz, a .19 to .55MHz, and a 6.0 to 9.1MHz receiver in a three-unit rack. Any two transmitters covering the desired frequency ranges would be in the transmitter rack. The two transmitters would be fixed-tuned before take-off, with the pilot able to select the desired transmitter and control the mode (Voice, MCW, CW) at the transmitter control box. The receivers were tuned at the pilot's control box by electrical cables and long mechanical tuning shafts, allowing remote control of power, mode, frequency, and volume.
AN/ARC-5 set composition and control differed markedly from the earlier systems. Three-unit receiver racks were still predominant, but the receiver line-up was quite different. One receiver would usually be a R-4A homing receiver, another the VHF R-28/ARC-5, and the last an MF/HF communication receiver. The transmitter rack would hold a VHF T-23/ARC-5 and an MF/HF transmitter corresponding to the MF/HF receiver. Frequency-stabilized versions of the AN/ARC-5 communications receivers usually have a yellow circle-S stamped on the front panel. Such receivers were not remotely tuned by the pilot, but were instead lock-tuned to the associated transmitter's frequency before take-off. AN/ARC-5 navigation receivers are not so stabilized, and if installed in the rack a control that allows remote tuning is required.
Because of these characteristics, AN/ARC-5 close equivalents to the control boxes of the ARA/ATA and SCR-274-N are rare or never existed. The most common AN/ARC-5 receiver remote control box is the C-38/ARC-5, which allows control only of audio volume of the VHF and MF/HF receivers. No power, mode, or frequency controls are present. The C-38 also has controls for the R-4A homing receiver. A common AN/ARC-5 transmitter control box C-30A/ARC-5 has controls for selecting the MF/HF transmitter or the VHF transmitter, and a switch to select the channel for both the VHF transmitter and receiver. Mode controls are normally set for voice and covered.
The typical AN/ARC-5 three-receiver, two-transmitter installation reflects system capabilities that are quite sophisticated compared to the earlier systems, allowing VHF homing, four channel VHF-AM communications, and one channel MF/HF-AM communications. All unnecessary controls have been eliminated to simplify operation of this more capable system.
Aircraft Radio Corporation, along with Stromberg-Carlson, made most AN/ARC-5 units except for the Western Electric VHF units.
Legacy
The AN/ARC-5 certainly represents the climax development of the pre-war MF/HF command set. But its VHF AN/ARC-5 set and the AN/ARR-2 homing adapter presaged a move toward higher frequencies. During World War II, the Navy began a slow movement toward VHF-AM for command functions in theaters where it made sense, beginning with the Western Electric WE-233A commercial airline set which was later re-designated the AN/ARC-4. By 1943 they began deploying their own AN/ARC-1 ten-channel VHF-AM set in increasing numbers, but hedged their bets with the AN/ARC-5 VHF sets in certain aircraft. This experimentation even caused them to contract for and officially nomenclature a continuously tunable AN/ARC-5 VHF capability from Aircraft Radio Corporation for evaluation purposes, shown in the above chart, but by that time (latter part of 1944) channelized equipment became the preferred technology to reduce aircrew "fiddling" with controls, so it was not pursued beyond the evaluation quantities. By late war, the discovery of "ducting" in the lower VHF band (that allowed Japanese tactical radio intercepts over long distances under certain conditions) drove development of the AN/ARC-12 (UHF version of the AN/ARC-1) and AN/ARC-27 sets in currently-used UHF-AM military aircraft band. However, it is important to understand that this gradual movement to VHF was not accomplished overnight, and there were still pockets of documented HF command set employment through war's end, especially in smaller aircraft.
In terms of longevity, the AN/ARR-2 continued into service well into the 1950s, and the beacon band R-23A/ARC-5 receiver was still to be found in some older US Navy aircraft as late as the 1970s.
Amateur radio use
Two war-surplus command set receivers series modified for amateur radio use by replacing the front connector with a small control panel
After World War II, surplus HF receivers and transmitters of the AN/ARC-5 family were extensively used in amateur radio stations. According to CQ magazine publisher Wayne Green, they first appeared for public purchase in March 1947, with thousands eventually becoming available, making them "by far the most popular surplus item to appear on the market." Green's magazine alone published some 47 articles on converting command sets to amateur use over the following 10 years, reprinting them in a compendium in 1957.[3]:pp. 3–5 Interest has continued into the 21st century.[4]
Other users
The T-16 and T-17 transmitters which operated in the standard broadcast band were very hard to find on the surplus market but were used by some as low power "pirate" AM stations with the addition of a modulation transformer in the B+ line and a suitable audio amplifier which was a 50 watt PA, guitar, or 'HI-FI home entertainment amplifier. The tuning system would allow the rig to be loaded into almost any kind of vertical or dipole antenna for neighborhood and beyond AM broadcasting. The on air fidelity of the unit was very good. One T-17 was used on 1580 by three different operators at three different locations in the Chicago suburbs as a pirate station in the 1960s with the local FCC office raiding each station at its location. The last raided operator repurposed the ARC5 as a driver for an ultrasonic nebulizer.
Gallery
SCR-274-N: Receivers BC-454-B, BC-453-B, BC-455-B in Rack FT-220-A.
SCR-274-N: Transmitters BC-457-A, BC-459-A in Rack FT-226-A.
SCR-274-N: Receiver Control BC-450-A, Transmitter Control BC-451-A, Modulator BC-456-B, Antenna Relay BC-442-A.
SCR-274-N and AN/ARR-1: Broadcast Band Receiver BC-946-B, Homing Adapter R-1/ARR-1.
AN/ARC-5 and AN/ARR-2: Homing Receiver R-4A/ARR-2, HF Receiver R-26/ARC-5, VHF Receiver R-28/ARC-5 in Rack MT-65/ARC-5.
AN/ARC-5 and AN/ARR-2: Receiver Control C-38/ARC-5, Transmitter Control C-30A/ARC-5, Audio Jack Box J-22/ARC-5, Modulator MD-7/ARC-5, Antenna Relay RE-2/ARC-5, DC Power Filter F-5/AR.
AN/ARC-5: Single Tunable Receiver Control C-26/ARC-5, Beacon Band Receiver R-23A/ARC-5 with ILS Adapter MX-19/ARC-5, Broadcast Band Receiver R-24/ARC-5 with Local Control C-24/ARC-5, Local Control Shorting Plug MX-2/ARR-2.
Underside view of a BC-453, left half of stereo pair
Underside view of a BC-453, right half of stereo pair
The International Telecommunication Union uses an internationally agreed system for classifying radio frequency signals. Each type of radio emission is classified according to its bandwidth, method of modulation, nature of the modulating signal, and type of information transmitted on the carrier signal. It is based on characteristics of the signal, not on the transmitter used.
Marine VHF radio is a worldwide system of two way radio transceivers on ships and watercraft used for bidirectional voice communication from ship-to-ship, ship-to-shore, and in certain circumstances ship-to-aircraft. It uses FM channels in the very high frequency (VHF) radio band in the frequency range between 156 and 174 MHz, designated by the International Telecommunication Union as the VHF maritime mobile band. In some countries additional channels are used, such as the L and F channels for leisure and fishing vessels in the Nordic countries. Transmitter power is limited to 25 watts, giving them a range of about 100 kilometres.
Clansman is the name of a combat net radio system (CNR) used by the British Army from 1976 to 2010.
The AN/ART-13 was a radio transmitter manufactured by Collins Radio that found widespread use during and after World War II in military aircraft.
The BC-348 is an American-made communications receiver, which was mass-produced during World War II for the U.S. Army Air Force. Under the joint Army-Navy nomenclature system, the receiver system became known as the AN/ARR-11.
The R-390A /URR is a general coverage HF radio communications receiver designed by Collins Radio Company for the United States Armed Forces.
During World War II, the German Luftwaffe relied on an increasingly diverse array of electronic communications, IFF and RDF equipment as avionics in its aircraft and also on the ground. Most of this equipment received the generic prefix FuG for Funkgerät, meaning "radio equipment". Most of the aircraft-mounted Radar equipment also used the FuG prefix. This article is a list and a description of the radio, IFF and RDF equipment.
The Wireless Set No. 19 was a Second World War mobile radio transceiver designed for use by armoured troops of the British Army. First introduced in 1940, the No. 19 began to replace the pre-war Wireless Set No. 11. Two modified versions were introduced, Mk. II in 1941 and Mk. III in 1942. An improved version from Canada was introduced in 1942 for use primarily with other forces. In British service, the No. 19 was replaced in the post-war era by the Larkspur radio system. Canadian-built No. 19s saw continued service for many years with a variety of users.
The SCR-299 was a U.S. Signal Corps mobile military communications unit used during World War II.
Survival radios are carried by pilots and search and rescue teams to facilitate rescue in an emergency. They are generally designed to transmit on international distress frequencies. Maritime systems have been standardized under the Global Maritime Distress Safety System. Civil and military organisation's utilized different frequencies to communicate and no infringement on either sector would take place. For emergencies involving civilian aircraft, the radio frequency used is VHF 121.5 MHz and for military aircraft incidents, the frequency used is UHF 243 MHz.
The SCR-300, designated AN/VRC-3 under the Joint Electronics Type Designation System, was a portable radio transceiver used by US Signal Corps in World War II. This backpack-mounted unit was the first radio to be nicknamed a "walkie talkie".
Radar in World War II greatly influenced many important aspects of the conflict. This revolutionary new technology of radio-based detection and tracking was used by both the Allies and Axis powers in World War II, which had evolved independently in a number of nations during the mid 1930s. At the outbreak of war in September 1939, both the United Kingdom and Germany had functioning radar systems. In the UK, it was called RDF, Range and Direction Finding, while in Germany the name Funkmeß (radio-measuring) was used, with apparatuses called Funkmessgerät . By the time of the Battle of Britain in mid-1940, the Royal Air Force (RAF) had fully integrated RDF as part of the national air defence.
The SCR-245 Radio was a mobile MF/HF Signal Corps Radio used by the U.S. Army before and during World War II, for short range ground communications, It was one of the first crystal controlled sets used by the Army.
The SCR-508 radio was a mobile Signal Corps Radio used by the U.S. Army during World War II, for short range ground communications. The SCR-508 series radio represented the Army's commitment to both FM and crystal tuning, and was used extensively by armor and mechanized units. The turret bustle of late series light and medium tanks was designed around this radio.
During World War II, the German Army relied on an diverse array of communications to maintain contact with its mobile forces and in particular with its armoured forces. Most of this equipment received the generic prefix FuG for Funkgerät, meaning "radio device". Occasionally the shorted Fu designation were used and there were exceptions to both these systems. Number ranges were not unique across the services so sometimes different equipment used by different services had the same FuG prefix. This article is a list and a description of the radio equipment.
The AN/ARC-182 is a family of military aircraft radio transceivers designed for two-way, multi-mode voice communications over a 30 to 400 MHz frequency range. It covers both Ultra High Frequency (UHF) and Very High Frequency (VHF) bands with AM, FM, as appropriate. The ARC-182 radio supports the HAVE QUICK II anti-jam waveforms, with an optional control unit. It features a guard channel capability for monitoring 40.5, 121.5, 156.8 and 243 MHz. Transmitter minimum power is 10 watts, AM, and 15 watts, FM. The RT-1250A model radio can communicate with other avionics over a MIL-STD-1553 data bus.
The AN/PRC-10 is an American VHF portable radio transceiver, introduced in 1951 as a replacement for the wartime SCR-300 set. The AN/PRC-8 and AN/PRC-9 sets are basically the same but cover lower frequency bands. It remained in service with the American military until the mid 1960s when it was replaced by the transistorized AN/PRC-25 set.
↑ Hanz, Mike. "Overview". AAF Radio. Retrieved 23 October 2024.
1 2 Wayne Green (1957). "Command Sets"(PDF). Radio Manual. Retrieved 12 September 2022. …many articles have appeared in CQ during the last ten years covering modifications of the units. The demand for these articles has been so heavy that every issue of CQ that carried them was long ago sold out…
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
