Atlantic Coast Line class R-1

Last updated
Atlantic Coast Line R-1 class
Type and origin
Power typeSteam
Builder Baldwin Locomotive Works
Serial number62174-62185
Build dateMarch–May, 1938
Total produced12
Specifications
Configuration:
   Whyte 4-8-4
   UIC 2′D2′ h2
Gauge 4 ft 8+12 in (1,435 mm) standard gauge
Driver dia.80 in (2,032 mm)
Wheelbase 97 ft 11 in (29.85 m)
Height16 ft (4,877 mm)
Axle load 65,792 lb (29,843 kg; 29.371 long tons)
Adhesive weight 263,127 lb (119,352 kg; 117.467 long tons)
Loco weight460,270 lb (208,770 kg; 205.48 long tons)
Tender weight435,500 lb (197,500 kg; 194.4 long tons)
Total weight895,770 lb (406,310 kg; 399.90 long tons)
Fuel type Coal
Fuel capacity27 short tons (24 t)
Water cap.24,000 US gal (91,000 L; 20,000 imp gal)
Firebox:
  Grate area97.75 sq ft (9.081 m2)
Boiler86+316 in (2,189 mm)
Boiler pressure275 lbf/in2 (1.90 MPa)
Heating surface:
  Firebox568 sq ft (52.8 m2)
  Total surface4,749 sq ft (441.2 m2)
Superheater:
  TypeType 'A'
  Heating area1,497 sq ft (139.1 m2)
Cylinders Two
Cylinder size 27 in × 30 in (686 mm × 762 mm)
Valve gear Walschaert
Performance figures
Maximum speed100 mph (160 km/h)
Tractive effort 63,900 lbf (284.24 kN)
Factor of adh. 4.12
Career
Operators Atlantic Coast Line
Class R-1
Numbers1800–1811
Retired1951-1952
DispositionAll scrapped

The Atlantic Coast Line R-1 was a class of 12 4-8-4 Northern type steam locomotives built by the Baldwin Locomotive Works in 1938 and operated by the Atlantic Coast Line Railroad until the early 1950s. They were immediately assigned to passenger service but eventually saw service pulling freight.

Contents

History

Upon delivery to the Atlantic Coast Line, the locomotives were immediately put in passenger service due to an increase in passenger business in the 1930s. Their P class Pacifics handled no more than 14 passenger cars without double-heading. The R-1s handled passenger trains up to 21 heavyweight cars, eliminating the need for double-heading and ran extra sections of many of the Richmond, Virginia to Jacksonville, Florida passenger trains. While they were more powerful than their Pacifics as well as being faster, running as fast as 90 mph and probably 100 mph without much trouble reaching such speeds, the ACL was very disappointed with them, as they had poor counterbalancing and were returned to Baldwin to solve the problem. When delivered, they had a bad dynamic augment. Even after the rebuild with new disk driving wheels, they still had unacceptable amounts of dynamic augment at high speeds, as their counterbalancing weights were too high, which led to the locomotive's drivers pounding at high speeds and was said that the main drivers actually left the rails and repeatedly slammed back down, kinking rails and damaging track alignment for miles. Despite their flaws, they were capable pullers. No. 1800 accelerated a 20-car, 1500-ton passenger train from a dead stop to 70 miles per hour in 11+12 minutes and 11 miles in a test. The class also ran as many as 18,000 miles a month in passenger service. R-1s Nos. 1800, 1801, 1806, 1807, 1808 and 1809 ran even more smoothly once they were fitted with lightweight pistons by Timken, piston rods, cross heads, and, probably most important, tapered main rods with roller bearing wrist pins. The class is rated at 6,200 tons on the Richmond to Jacksonville mainline. [1] With dieselization taking effect, the locomotives were put in freight service. Retirement started in 1951 and by 1952, all have been retired. [2]

Tenders

The R-1 class were equipped with very large tenders holding 24,000 US gallons (91,000 L; 20,000 imp gal) of water and 27 short tons (24 long tons) of coal. They were mounted on a pair of eight-wheel trucks. The weight of the tender, fully loaded was 217 short tons (194 long tons) [3] In 1953, ten of the R-1 tenders were sold to the Norfolk and Western Railway (N&W), where they were paired with their Y4 class 2-8-8-2 compound mallets, until they were all scrapped in 1958. [4]

Disposition

None of the R-1s have been preserved, as all were scrapped by 1952 and the remaining ten tenders lasted on the N&W until 1958. [1]

Roster

NumberBaldwin serial numberDate builtDispositionNotes
180062174March 1938Scrapped on December 20, 1951.
180162175March 1938Scrapped on June 20, 1952.
180262176March 1938Scrapped on June 20, 1952.
180362177March 1938Scrapped on December 20, 1951. [5]
180462178March 1938Scrapped on December 20, 1951.
180562179March 1938Sold for scrap.
180662180May 1938Sold for scrap.
180762181May 1938Sold for scrap.
180862182May 1938Scrapped on June 20, 1952.
180962183May 1938Sold for scrap.
181062184May 1938Sold for scrap.
181162185May 1938Scrapped on June 20, 1952.

Related Research Articles

<span class="mw-page-title-main">New York Central Mohawk</span> Class of NYC 4-8-2 locomotives

The New York Central Railroad (NYC) called the 4-8-2 type of steam locomotive the Mohawk type. It was known as the Mountain type on other roads, but the New York Central did not see the name as fitting on its famous Water Level Route. Instead, it picked the name of one of those rivers its rails followed, the Mohawk River, to name its newest type of locomotive.

<span class="mw-page-title-main">4-6-4</span> Locomotive wheel arrangement

Under the Whyte notation for the classification of locomotives, 4-6-4 represents the wheel arrangement of four leading wheels, six powered and coupled driving wheels and four trailing wheels. In France where the type was first used, it is known as the Baltic while it became known as the Hudson in most of North America.

<span class="mw-page-title-main">4-8-4</span> Locomotive wheel arrangement

Under the Whyte notation for the classification of steam locomotives, 4-8-4 represents the wheel arrangement of four leading wheels on two axles, eight powered and coupled driving wheels on four axles and four trailing wheels on two axles. The type was first used by the Northern Pacific Railway, and initially named the Northern Pacific, but railfans and railroad employees have shortened the name since its introduction. It is most-commonly known as a Northern.

<span class="mw-page-title-main">Booster engine</span>

A locomotive booster for steam locomotives is a small supplementary two-cylinder steam engine back-gear-connected to the trailing truck axle on the locomotive or one of the trucks on the tender. It was invented in 1918 by Howard L. Ingersoll, assistant to the president of the New York Central Railroad.

<span class="mw-page-title-main">Seaboard Coast Line Railroad</span> Transport company

The Seaboard Coast Line Railroad was a Class I railroad company operating in the Southeastern United States beginning in 1967. Its passenger operations were taken over by Amtrak in 1971. Eventually, the railroad was merged with its affiliate lines to create the Seaboard System in 1983.

<span class="mw-page-title-main">Norfolk and Western Railway</span> Former US Class I railroad (1838–1982)

The Norfolk and Western Railway, commonly called the N&W, was a US class I railroad, formed by more than 200 railroad mergers between 1838 and 1982. It was headquartered in Roanoke, Virginia, for most of its existence. Its motto was "Precision Transportation"; it had a variety of nicknames, including "King Coal" and "British Railway of America". In 1986, N&W merged with Southern Railway to form today's Norfolk Southern Railway.

<span class="mw-page-title-main">2-8-4</span> Locomotive wheel arrangement

Under the Whyte notation, a 2-8-4 is a steam locomotive that has two unpowered leading wheels, followed by eight coupled and powered driving wheels, and four trailing wheels. This locomotive type is most often referred to as a Berkshire, though the Chesapeake and Ohio Railway used the name Kanawha for their 2-8-4s. In Europe, this wheel arrangement was mostly seen in mainline passenger express locomotives and, in certain countries, in tank locomotives.

<span class="mw-page-title-main">Atlantic Coast Line Railroad</span> Defunct American Class I railroad

The Atlantic Coast Line Railroad was a United States Class I railroad formed in 1900, though predecessor railroads had used the ACL brand since 1871. In 1967, it merged with long-time rival Seaboard Air Line Railroad to form the Seaboard Coast Line Railroad. Much of the original ACL network has been part of CSX Transportation since 1986.

<span class="mw-page-title-main">4-4-2 (locomotive)</span> Railway locomotive wheel arrangement

Under the Whyte notation for the classification of steam locomotives by wheel arrangement, 4-4-2 represents a configuration of a four-wheeled leading bogie, four powered and coupled driving wheels, and two trailing wheels supporting part of the weight of the boiler and firebox. This allows a larger firebox and boiler than the 4-4-0 configuration.

<span class="mw-page-title-main">FM Consolidation Line</span> Series of American locomotive models

The Consolidation Line was a series of diesel-electric railway locomotive designs produced by Fairbanks-Morse and its Canadian licensee, the Canadian Locomotive Company. Railfans have dubbed these locomotives C-liners, however F-M referred to the models collectively as the C-Line. A combined total of 165 units were produced by F-M and the CLC between 1950 and 1955.

<span class="mw-page-title-main">EMD SDP35</span> American model of diesel-electric locomotive

The EMD SDP35 is a model of 6-axle diesel-electric locomotive built by General Motors Electro-Motive Division between July 1964 and September 1965. Power was provided by an EMD 567D3A 16-cylinder engine which generated 2,500 horsepower (1.9 MW). Essentially this locomotive was an EMD SD35 equipped with a steam generator, located in the extended long hood end, for passenger use. 35 examples of this locomotive model were built for American railroads.

<i>Powhatan Arrow</i>

The Powhatan Arrow was a named luxurious passenger train, operated by the Norfolk and Western Railway (N&W) in the United States. It made its inaugural operation on April 28, 1946, with two trains; Nos. 25 and 26, which both ran 676 miles (1,088 km) daily at daylight on the N&W mainline between Norfolk, Virginia, and Cincinnati, Ohio in opposite directions. It takes about 15 hours and 45 minutes for both trains to run per day. They were hauled behind N&W's streamlined 4-8-4 class J steam locomotives.

<span class="mw-page-title-main">Norfolk and Western J Class (1941)</span> Class of 14 American 4-8-4 locomotives

The Norfolk and Western J class was a class of 14 4-8-4 "Northern" streamlined steam locomotives built by the Norfolk and Western Railway (N&W) at its Roanoke Shops in Roanoke, Virginia, between 1941 and 1950. The most powerful 4-8-4 locomotives ever produced, the J class were part of the N&W's "Big Three" that represented the pinnacle of steam technology.

<span class="mw-page-title-main">Southern Railway 1401</span> Preserved American 4-6-2 locomotive (SOU Ps-4 class)

Southern Railway 1401 is a 4-6-2 steam locomotive built in July 1926 by the American Locomotive Company (ALCO) of Richmond, Virginia, for the Southern Railway (SOU) as a member of the Ps-4 class, which was based on the United States Railroad Administration (USRA) Heavy Pacific design with some minor differences. It was assigned to haul SOU's premier passenger trains between Washington, D.C., and Atlanta, Georgia.

<span class="mw-page-title-main">Southern Railway Ps-4 class</span> Class of 64 American 4-6-2 locomotives

The Southern Railway Ps-4 was a class of 4-6-2 steam locomotives built for the Southern Railway, as well as its subsidiaries, the Alabama Great Southern Railroad and the Cincinnati, New Orleans and Texas Pacific Railway. The locomotives were notable for their green with gold trim liveries, and have been regarded by Smithsonian curator John H. White Jr. as being "among the most celebrated passenger locomotives operated in the United States...."

<i>Chessie</i> (train) Proposed passenger train

The Chessie was a proposed streamlined passenger train developed by the Chesapeake and Ohio Railway (C&O) in the late 1940s. The brainchild of C&O executive Robert R. Young, the Chessie would have operated on a daylight schedule between Washington, D.C., and Cincinnati, Ohio. The train's luxury lightweight equipment was built new by the Budd Company. A revolutionary new steam turbine locomotive would have provided power, including speeds up to 100 miles per hour (160 km/h). Although the equipment was delivered, a worsening financial outlook led to the cancellation of the train before it operated in revenue service.

<span class="mw-page-title-main">Atlantic Coast Line 1504</span> Preserved ACL P-5-A class 4-6-2 locomotive

Atlantic Coast Line 1504 is a 4-6-2 steam locomotive built in March 1919 by the American Locomotive Company (ALCO) of Richmond, Virginia, for the Atlantic Coast Line Railroad (ACL) as a member of the P-5-A class under the United States Railroad Administration (USRA) standard. No. 1504 was assigned to pull ACL's premier main line passenger trains during the 1920s to early 40s and even main line freight trains in the late 1940s until it was retired from revenue service at the end of 1952.

<span class="mw-page-title-main">Norfolk and Western A class</span>

The Norfolk and Western A was a class of 43 2-6-6-4 simple articulated steam locomotives built by the railroad's own Roanoke Shops between 1936 and 1950 and operated until the late 1950s. The locomotives hauled fast and heavy freight trains for the railroad and only one has been preserved, No. 1218.

<span class="mw-page-title-main">Chesapeake and Ohio class H-8</span> Class of 60 American 2-6-6-6 locomotives

The Chesapeake and Ohio class H-8 was a class of 60 simple articulated 2-6-6-6 steam locomotives built by the Lima Locomotive Works in Lima, Ohio between 1941 and 1948, operating until the mid 1950s. The locomotives were among the most powerful steam locomotives ever built and hauled fast, heavy freight trains for the railroad. Only two units were preserved; Nos. 1601 and 1604.

The Southern Railway Ss was a class of 2-10-2 "Santa Fe" type steam locomotives built in 1917 and 1918 for the Southern Railway (SOU). They were assigned to haul and bank heavy freight trains over the Saluda Grade and Old Fort Loops in the Blue Ridge Mountains of North Carolina.

References

  1. 1 2 "Atlantic Coast Line 4-8-4s". www.trainweb.org.
  2. "Atlantic Coast Line 4-8-4 "Northern" Locomotives in the USA". steamlocomotive.com.
  3. Reed, Brian (1983). Loco Profile 20: The American 4-8-4. Windsor, Berkshire: Profile Publications Limited. p. 6.
  4. Dixon, Thomas W. Jr.; Parker, Karen; Huddleston, Gene (2009). Norfolk & Western's Y-Class Articulated Steam Locomotives. TLC Publishing. pp. 61–63.
  5. Tillotson Jr. (2000) , p. 91.

Bibliography

Further reading