Italian Device Registration

Last updated

The Italian Ministry of Health (MOH) has implemented mandatory procedures for the Italian registration of medical devices as of 1 May 2007.

Contents

Overview

Placing a Medical Device into the European market is contingent upon compliance with the Medical Device Directive (93/42/EEC). While this directive applies in all member states of the European Union, each member state has its own way of implementing the directive within their country, essentially adding regulations to the directive and creating local legislation.

An example of such local implementation of the Directive is now present in Italy. Italy requires, in addition to the CE marking (as opposed to the essence of the CE marking which is “Free Circulation of Goods”), that ALL Medical Devices to be placed in the Italian market will go through a Device registration process. This process is similar to the pre-market notification requirement for Class I Medical Devices (as stated in the European Directive MDD 93/42/EEC Article 14); however, in Italy it is applicable for all classes, not only Class I.

Local legislations, such as this one, are growing rapidly in Europe and strengthen the need for a professional European Authorized Representative present at all times.

There are two different registration possibilities that should not be mixed up: Basic registration of medical devices in the medial device database, and optional registration in the Repertorio to aid in marketing medical devices to the Italian National Health Service.

Solution

As a non-EU manufacturer of medical devices, the manufacturer's legal representative must appoint a "responsible individual person or company" to register their product with the Italian database. The official form needed is available here:

This "responsible individual person or company" will communicate with the Italian Ministry of Health on the manufacturer’s behalf. The registration can only be done with granted access to the Italian Database, and with the required “smart card” for the actual registration. The legal representative needs to have access to both.

Third party commercial entities, like distributors, should not register products for several reasons, a few of which are:

  1. By allowing a third party commercial entity to register in the manufacturer’s behalf, he/she relinquishes an essential part of his/her control over his/her product in Italy.
  2. If the manufacturer decided to end the relationship with the commercial distributor at any point, they would be required to take their product completely off the market until they could re-register that product within Italy for a second (third, fourth, etc.) time.
  3. A third party commercial entity will expect exclusivity, limiting the open distribution of the product.

Conclusion

The manufacturer should register their products through their Italian distributor who is not only familiar with the language and local regulations but also has responsibility if he is the "c) other individual responsible for trading medical devices as under article 13, paragraph 2 of legislative decree no. 46 of 24 February 1997" as mentioned in the official form here:

See also

Related Research Articles

<span class="mw-page-title-main">Regulation of therapeutic goods</span> Legal management of drugs and restricted substances

The regulation of therapeutic goods, defined as drugs and therapeutic devices, varies by jurisdiction. In some countries, such as the United States, they are regulated at the national level by a single agency. In other jurisdictions they are regulated at the state level, or at both state and national levels by various bodies, as in Australia.

<span class="mw-page-title-main">CE marking</span> Declaration of conformity with European standards

On commercial products, the letters CE mean that the manufacturer or importer affirms the goods' conformity with European health, safety, and environmental protection standards. It is not a quality indicator or a certification mark. The CE marking is required for goods sold in the European Economic Area (EEA), but is also found on products sold elsewhere that have been manufactured to EEA standards.

<span class="mw-page-title-main">Medical device</span> Device to be used for medical purposes

A medical device is any device intended to be used for medical purposes. Significant potential for hazards are inherent when using a device for medical purposes and thus medical devices must be proved safe and effective with reasonable assurance before regulating governments allow marketing of the device in their country. As a general rule, as the associated risk of the device increases the amount of testing required to establish safety and efficacy also increases. Further, as associated risk increases the potential benefit to the patient must also increase.

<span class="mw-page-title-main">Directive 67/548/EEC</span>

The Dangerous Substances Directive was one of the main European Union laws concerning chemical safety, until its full replacement by the new regulation CLP Regulation (2008), starting in 2016. It was made under Article 100 of the Treaty of Rome. By agreement, it is also applicable in the EEA, and compliance with the directive will ensure compliance with the relevant Swiss laws. The Directive ceased to be in force on 31 May 2015 and was repealed by Regulation (EC) No 1272/2008 of the European Parliament and of the Council of 16 December 2008 on classification, labelling and packaging of substances and mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending Regulation (EC) No 1907/2006.

In the experimental (non-clinical) research arena, good laboratory practice or GLP is a quality system of management controls for research laboratories and organizations to ensure the uniformity, consistency, reliability, reproducibility, quality, and integrity of products in development for human or animal health through non-clinical safety tests; from physio-chemical properties through acute to chronic toxicity tests.

ISO 13485Medical devices -- Quality management systems -- Requirements for regulatory purposes is a voluntary standard, published by International Organization for Standardization (ISO) for the first time in 1996, and contains a comprehensive quality management system for the design and manufacture of medical devices. The latest version of this standard supersedes earlier documents such as EN 46001 and EN 46002 (1996), the previously published ISO 13485, and ISO 13488.

<span class="mw-page-title-main">Battery Directive</span>

The Directive 2006/66/EC of the European Parliament and of the Council of 6 September 2006 on batteries and accumulators and waste batteries and accumulators and repealing Directive 91/157/EEC, commonly known as the Battery Directive, regulates the manufacture and disposal of batteries in the European Union with the aim of "improving the environmental performance of batteries and accumulators".

The European Chemicals Bureau (ECB) was the focal point for the data and assessment procedure on dangerous chemicals within the European Union (EU). The ECB was located in Ispra, Italy, within the Joint Research Centre (JRC) of the European Commission. In 2008 the ECB completed its mandate. Some of its activities were taken over by the European Chemicals Agency (ECHA); others remained within the Joint Research Centre. The history of the ECB has been published as a JRC technical report.

<span class="mw-page-title-main">Medical Devices Directive</span>

The Medical Device DirectiveCouncil Directive 93/42/EEC of 14 June 1993 concerning medical devices — is intended to harmonise the laws relating to medical devices within the European Union. The MD Directive is a 'New Approach' Directive and consequently in order for a manufacturer to legally place a medical device on the European market the requirements of the MD Directive have to be met. Manufacturers' products meeting 'harmonised standards' have a presumption of conformity to the Directive. Products conforming with the MD Directive must have a CE mark applied. The Directive was most recently reviewed and amended by the 2007/47/EC and a number of changes were made. Compliance with the revised directive became mandatory on 21 March 2010.

<span class="mw-page-title-main">CLP Regulation</span> 2008 European Union regulation about chemicals

The CLP Regulation is a European Union regulation from 2008, which aligns the European Union system of classification, labelling and packaging of chemical substances and mixtures to the Globally Harmonised System (GHS). It is expected to facilitate global trade and the harmonised communication of hazard information of chemicals and to promote regulatory efficiency. It complements the 2006 Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH) Regulation and replaces an older system contained in the Dangerous Substances Directive (67/548/EEC) and the Dangerous Preparations Directive (1999/45/EC).

A European Authorised Representative (E.A.R.) serves as a legal entity designated by non European Union (EU) manufacturers, to represent them in the EU and ensure their compliance with the European Directives. The CE certificate and declaration of conformity can only be issued by a company located in the European Union.

Design controls designates the application of a formal methodology to the conduct of product development activities. It is often mandatory to implement such practice when designing and developing products within regulated industries.

The following outline is provided as an overview of and topical guide to clinical research:

<span class="mw-page-title-main">Construction Products Directive</span>

Construction Products Directive (Council Directive 89/106/EEC)(CPD) is a now repealed European Union Directive which aimed to remove technical barriers to trade in construction products between Member States in the European Union.

<span class="mw-page-title-main">Regulation (EU) No. 305/2011</span>

Regulation No. 305/2011 of the European Parliament and of the Council of the European Union is a regulation of 9 March 2011 that lays down harmonised conditions for the marketing of construction products and replaces Construction Products Directive (89/106/EEC). This EU regulation is designed to simplify and clarify the existing framework for the placing on the market of construction products.

Single-use medical device reprocessing is the disinfection, cleaning, remanufacturing, testing, packaging and labeling, and sterilization among other steps, of a used,, medical device to be put in service again. All reprocessed medical devices originally labeled for single use in the United States are subject to U.S. Food and Drug Administration (FDA) manufacturing requirements and must meet strict cleaning, functionality, and sterility specifications prior to use. Although first regulated in the U.S., the reprocessing of medical devices, particularly those that are labeled "Single Use Device" (SUDs), is a global practice with countries in Europe, Asia, Africa, and North America actively engaged in reprocessing. Currently, approximately 2% of all SUDs on the U.S. market are eligible for reprocessing by a qualified commercial vendor. Reprocessing industry estimates indicate the amount of revenue saved by hospitals that use reprocessed devices to be $471 million in 2018. Over 8,800 hospitals and surgical centers use reprocessed devices, in the U.S., Canada, Israel, Europe and Japan, according to the Association of Medical Device Reprocessors.

The Machinery Directive, Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 is a European Union directive concerning machinery and certain parts of machinery. Its main intent is to ensure a common safety level in machinery placed on the market or put in service in all member states and to ensure freedom of movement within the European Union by stating that "member states shall not prohibit, restrict or impede the placing on the market and/or putting into service in their territory of machinery which complies with [the] Directive".

<span class="mw-page-title-main">Regulation (EU) 2017/745</span> Political regulation

Regulation (EU) 2017/745 is a regulation of the European Union on the clinical investigation and sale of medical devices for human use. It repeals Directive 93/42/EEC (MDD), which concerns medical devices, and Directive 90/385/EEC, which concerns active implantable medical devices, on 26 May 2021.

A custom-made medical device, commonly referred to as a custom-made device (CMD) or a custom device, is a medical device designed and manufactured for the sole use of a particular patient. Examples of custom-made medical devices include auricular splints, dentures, orthodontic appliances, orthotics and prostheses.

References