Springfield Model 1865 | |
---|---|
Type | Breech-loading rifle |
Place of origin | United States |
Service history | |
Used by | United States |
Wars | American Civil War |
Production history | |
Designer | Erskine S. Allin |
Designed | 1865 |
Manufacturer | Springfield Armory |
Specifications | |
Length | 56 in (1,400 mm) |
Barrel length | 40.0 in (1,020 mm) |
Cartridge | Rimfire .58-60-500 |
Action | Trapdoor |
Rate of fire | User dependent; usually 8 to 10 rounds per minute |
Feed system | Breech-loading |
Sights | Open sights |
The Springfield Model 1865 was an early breech-loading rifle manufactured by U.S. Armory in Springfield, Massachusetts. It was a modification of the Springfield Model 1861. It was later replaced with the Springfield Model 1866.
During the U.S. Civil War, the advantage of breech-loading rifles became obvious. The rifled muskets used during the war had a rate of fire of 2 or 3 rounds per minute. Breech-loading rifles increased the rate of fire to 8 to 10 rounds per minute with the additional advantage that they can be easily loaded from a prone, rather than standing, position, reducing the rifleman's visible cross section and thus vulnerability to counter-fire. As the Civil War drew to a close, the U.S. Ordnance Department requested prototypes of breech-loading weapons from arms manufacturers all over the world.
After considerable testing, the prototype developed by Erskine S. Allin of the government-operated Springfield Armory was chosen for its simplicity and the fact that it could be produced by the modification of existing Springfield Model 1863 muskets. These modifications cost about $5 per rifle (around $97 adjusted for inflation), which was a significant savings at a time when new rifles cost about $20 each (around $387 adjusted for inflation). Patent No. 49,959 was issued to Erskine S. Allin on September 19, 1865, describing the design.
The conversion from musket to breech-loader was done by milling open the barrel's breech section and inserting a hinged breechblock fastened to the top of the barrel. A thumb-operated cam latch at the rear of the breechblock held it shut when in closed position. The rack-type system extractor was withdrawn automatically as the breech-block was opened and snapped back at the end of its stroke. The firing pin was housed within the breech-block. The hammer nose was flattened to accommodate the firing pin.
The breech mechanism employed a hinged breechblock that rotated up and forward, resembling the movement of a trapdoor, to open the breech of the rifle and permit insertion of a cartridge. The hinged breechblock caused these rifles to be named "Trapdoor Springfields".
Approximately 5,000 Civil War Model 1861 rifled muskets were converted at the Springfield Armory in 1866. It soon became apparent that many of the small working parts in the breech system were not going to have a long service life, and the action was too complicated for normal service use. Therefore, before the Model 1865 production order was completed, a less complex rifle was already being tested. This caused the Model 1865 to be called the "First Allin", and the following revised model, the Model 1866, to be called the "Second Allin".
The Model 1865 fired a rimfire .58-60-500 cartridge (.58 inch 500-grain (32 g) bullet, 60 grains (3.9 g) of black powder), the caliber matching that of the Civil War Minié ball, which was originally used in these rifles.
The Model 1865 quickly became obsolete, and most of them were sold in the 1870s to several American arms dealers. At the time, there was a large demand in the US for shorter cadet-style rifles. To satisfy this need, these dealers cut the barrels and stocks to make short rifles with 33" and 36" barrel lengths. Likewise, the stock wrists were often thinned for cadet use.
In firearm designs, the term single-shot refers to guns that can hold only a single round of ammunition inside and thus must be reloaded manually after every shot. Compared to multi-shot repeating firearms ("repeaters"), single-shot designs have no moving parts other than the trigger, hammer/firing pin or frizzen, and therefore do not need a sizable receiver behind the barrel to accommodate a moving action, making them far less complex and more robust than revolvers or magazine/belt-fed firearms, but also with much slower rates of fire.
In firearms terminology, an action is the functional mechanism of a breech-loading firearm that handles the ammunition cartridges, or the method by which that mechanism works. Actions are technically not present on muzzleloaders, as all those are single-shot firearms with a closed off breech with the powder and projectile manually loaded from the muzzle. Instead, the muzzleloader ignition mechanism is referred to as the lock.
The term Springfield rifle may refer to any one of several types of small arms produced by the Springfield Armory in Springfield, Massachusetts, for the United States armed forces.
The Springfield Model 1863 was a .58 caliber rifled musket manufactured by the Springfield Armory and independent contractors between 1863 and 1865.
A rifled musket, rifle musket, or rifle-musket is a type of firearm made in the mid-19th century. Originally the term referred only to muskets that had been produced as a smoothbore weapon and later had their barrels replaced with rifled barrels. The term later included rifles that directly replaced, and were of the same design overall as, a particular model of smoothbore musket.
A rolling-block action is a single-shot firearm action where the sealing of the breech is done with a specially shaped breechblock able to rotate on a pin. The breechblock is shaped like a section of a circle. The breechblock is locked into place by the hammer, therefore preventing the cartridge from moving backward at the moment of firing. By cocking the hammer, the breechblock can be rotated freely to reload the breech of the weapon.
The Kammerlader, or "chamber loader", was the first Norwegian breech-loading rifle, and among the first breech loaders adopted for use by an armed force anywhere in the world. A single-shot black-powder rifle, the kammerlader was operated with a crank mounted on the side of the receiver. This made it much quicker and easier to load than the weapons previously used. Kammerladers quickly gained a reputation for being fast and accurate rifles, and would have been a deadly weapon against massed ranks of infantry.
The .45-70 (11.6x53mmR), also known as the .45-70 Government, .45-70 Springfield, and .45-21⁄10" Sharps, is a .45 caliber rifle cartridge originally holding 70 grains of black powder that was developed at the U.S. Army's Springfield Armory for use in the Springfield Model 1873. It was a replacement for the stop-gap .50-70 Government cartridge, which had been adopted in 1866, one year after the end of the American Civil War, and is known by collectors as the "Trapdoor Springfield".
The Springfield Model 1873 was the first standard-issue breech-loading rifle adopted by the United States Army. The rifle, in both full-length and carbine versions, was widely used in subsequent battles against Native Americans.
The Springfield Model 1866 was the second iteration of the Allin-designed trapdoor breech-loading mechanism. Originally developed as a means of converting rifle muskets to breechloaders, the Allin modification ultimately became the basis for the definitive Springfield Model 1873, the first breech-loading rifle adopted by the United States War Department for manufacture and widespread issue to U.S. troops.
The Springfield Model 1870 was one of the rifles which used the trapdoor breechblock design developed by Erskine S. Allin. The Model 1870 was a minor improvement to the Springfield Model 1868, and retained most of the Model 1868 rifle features.
The Springfield Model 1868 was one of the rifles which used the trapdoor breechblock design developed by Erskine S. Allin.
The .50-70 Government / 12.7 x 45 mm R, also known as the .50-70 Musket, .50-70 Springfield, and .50-1+3⁄4" Sharps) is a black powder cartridge adopted in 1866 for the Springfield Model 1866 trapdoor rifle.
During the American Civil War, an assortment of small arms found their way onto the battlefield. Though the muzzleloader percussion cap rifled musket was the most numerous weapon, being standard issue for the Union and Confederate armies, many other firearms, ranging from the single-shot breech-loading Sharps and Burnside rifles to the Spencer and the Henry rifles - two of the world's first repeating rifles - were issued by the hundreds of thousands, mostly by the Union. The Civil War brought many advances in firearms technology, most notably the widespread use of rifled barrels.
The Springfield Model 1870 rolling-block U.S. Navy rifle was a shipboard small arm for use by the United States Navy, employing the Remington Arms Company rolling-block design, and manufactured under a royalty agreement with Remington.
The Springfield Model 1869 was one of several model "trapdoor Springfields", which used the trapdoor breechblock design developed by Erskine S. Allin.
The term Joslyn Rifle refers to a series of rifles produced in the mid-19th century. The term is often used to refer specifically to the Joslyn Model 1861/1862, which was the first mass-produced breech-loading rifle produced at the Springfield Armory.
In firearms, a trapdoor is a form of breech-loading mechanism for rifles in which a hinged breechblock rotates up and forward, resembling the movement of a trapdoor. The Springfield models 1865 and 1873 were best known for first employing this type of action.
Green percussion rifle was a breech-loading percussion rifle used in the army of the Principality of Serbia in the second half of the 19th century.
The Serbian Peabody rifle is a single-shot breech-loading rifle made and used in the Principality of Serbia in the second half of the 19th century. It was the first Serbian military rifle to use metallic cartridges.