Voyetra-8

Last updated

The Voyetra-8 (Voyetra-Eight) is an eight voice polyphonic analog synthesizer. Released in 1982 by Octave-Plateau Electronics (later renamed Voyetra and still later merged with Turtle Beach Systems to become Voyetra Turtle Beach, Inc.), it was one of the first analog programmable synthesizers to be rack-mountable and remains one of the most flexible digitally controlled analog synthesizers.

Contents

Design

The Voyetra-8 is a 19" rack-mountable device, 3 rack units high at the face. Most units are bowed at the top and so cannot be placed below other rack mounted equipment more than a few inches deep. It is approximately 16 inches deep in the rack, and weighs around 38 lbs. Rear mounted plugs and a large heat sink make at least 4" rear clearance advisable.

The front panel has numerous buttons and knobs, which are active in live performance. However, the instrument is more complicated than it looks; there are fourteen "pages" of controls. Extra "pages" are accessed by hitting certain shift key combinations, after which most of the front-panel controls change function. These pages are used when setting up the instrument and programming sounds.

The rear panel has a mono output and a stereo output. When connected in stereo, one four-voice sound appears at each output if the instrument is in Dual or Layer mode, or the eight voices are each panned in different places between the outputs if the instrument is in Whole-8 mode.

The memory, which stores all of the user presets and parameters, can be dumped via MIDI to any sequencer. The dump is not MIDI System Exclusive (SysEx); it is encoded into controller changes and other common MIDI data, which any sequencer can handle. This may seem somewhat unusual, but in the day of the Voyetra, MIDI was in its infancy, and SysEx was not yet a proven strategy for transmitting and storing system information.

Architecture

The Voyetra-8 has 8 separate programmable analog voice cards. Each produces one voice of the maximum 8. It can store 100 "Programs", and can play either one 8-voice sound in Whole-8 mode, a different 4-voice sound on each half of the keyboard (or on different MIDI channels) in Split mode, or two 4-voice sounds per note (which could both be the same) in Layer mode.

The keyboard mode, key assignment mode, two selected sounds, and a number of parameter trims and tweaks (such as octave shift on either Voice, detune, and cutoff frequency offset) are stored as a "Step". The instrument can store 100 Steps. Generally, a performer will call up Steps, not Voices, during live performance; each Step will call up two of the Voices and tweak them for the song to be played.

Each voice has two VCOs, one VCA, one 24 dB/octave lowpass VCF, two LFOs, two ADSRs, noise generator, sync VCO 1 to VCO 2. (More detailed specs follow.)

The specs belie the complexity of the sound architecture, because of the great deal of control the programmer (and the player) has over various aspects of sound production, including key assignment modes, modulation routing, and envelope parameters.

Key assignment modes and envelope parameters

Any polyphonic instrument must use an algorithm to assign available voices to played notes (unless the instrument has enough voices to cover all of the notes). If a player is holding down 8 notes and hits another, does it sound? If so, does it rob the oldest note played or one of the others? If notes are not being held down but still decaying, will they be robbed? If a note is played repeatedly, does the same voice sound again or does another voice trigger, layered on top of the first? Many of the answers to these questions can be set by the programmer using the key assignment modes and envelope parameters.

In Whole-8 mode, the Voyetra-8 has 8 voices. In Split mode, it has two sets of four. In Layer mode, it has four.

Key assignment modes are stored with the Step, not the Voice. The following are the possible key assignment modes:

Extra envelope parameters (besides the Attack time, Decay time, Sustain level, and Release time) also control the way the sound responds to the keyboard.

Modulation banks

The instrument contains a sophisticated matrix for the handling and routing of control voltages. There are four modulation "banks" per Voice. Each modulation bank is independent of the others; within each a modulation source and one or more destinations is chosen, and a controller is selected if it is desired to alter the amount of modulation during live performance.

For instance, on modulation bank A, one might choose LFO1 one as the source, VCO1 and VCO2 pitch as the destination, and channel aftertouch (pressure) as the controller. This could add vibrato to the notes when aftertouch pressure was applied to the keyboard. In bank B, one might then choose DC as the source, VCO2 pitch as the destination, and velocity as the controller. This could be used to detune VCO2 slightly relative to VCO1 when a note is struck hard.

Modulation sources

  • LFO1 sine
  • LFO1 square
  • LFO2
  • VCO1
  • VCO2
  • ADSR1
  • ADSR2
  • DC (direct current, for producing an offset)

Modulation controllers

  • Velocity
  • Channel aftertouch (pressure)
  • Joystick +X
  • Joystick -X
  • Keyboard tracking
  • ADSR1 (Banks A, B only)
  • Noise (Bank C only)
  • Pedal (Bank D only)

Note: Joystick +X and Joystick -X each can be assigned its own MIDI Continuous Controller number. Also, a global parameter setting on the Voy will invert the sense of the Joystick for the left Voice in all Steps that use Split Mode so that the left Voice gets the -X as a positive value. When this is done, the -X controller can be used to positively control modulation on the left Voice, while the +X controller can be used to positively control modulation of the right voice.

Modulation destinations

Note that any combination of multiple destinations can be selected per bank.

  • filter cutoff
  • filter Q
  • VCO 1
  • VCO 2

Specs

Controllers

The Voyetra VPK-5 keyboard, if used, is connected to the head using an XLR mic cable. This XLR cable, while compatible with those used by the Voyetra-8's MIDI, does not carry MIDI data. The Voyetra is fully controllable from a MIDI controller or sequencer. The VPK-5 keyboard has a joystick to the left of the keys where the pitch and mod wheels would commonly be found on other synthesizers.

Idiosyncrasies

Trivia

In New Order's promotional music video for their 1985 single "The Perfect Kiss", the Voyetra-8 appears in the first scenes of the clip used by band member Gillian Gilbert. New Order used to tour with a rack containing four Voyetra-8s, although two were spares as early units tended to break down regularly. Gary Pozner, keyboard player for Tom Tom Club, also used the Voyetra-8, as his main synthesizer.

Related Research Articles

<span class="mw-page-title-main">Novation Digital Music Systems</span> British musical equipment manufacturer

Novation Digital Music Systems Ltd. is a British musical equipment manufacturer, founded in 1992 by Ian Jannaway and Mark Thompson as Novation Electronic Music Systems. Today the company specializes in MIDI controllers with and without keyboards, both analog and virtual analog performance synthesizers, grid-based performance controllers, and audio interfaces. At present, Novation products are primarily manufactured in China.

<span class="mw-page-title-main">Ensoniq ESQ-1</span> Synthesizer

Ensoniq ESQ-1 is a 61-key, velocity sensitive, eight-note polyphonic and multitimbral synthesizer released by Ensoniq in 1985. It was marketed as a "digital wave synthesizer" but was an early Music Workstation. Although its voice generation is typically subtractive in much the same fashion as most analog synthesizers that preceded it, its oscillators are neither voltage nor "digitally controlled", but true digital oscillators, provided by a custom Ensoniq wavetable chip. The signal path includes analog resonant low-pass filters and an analog amplifier.

The Yamaha AN1x is a DSP-based analog modeling synthesizer, produced by Yamaha Corporation from 1997 to 1998, and was marketed as an "analog physical modelling control synthesizer".

<span class="mw-page-title-main">Roland Jupiter-4</span> Polyphonic analog synthesizer

The Roland Jupiter-4 (JP-4) was an analog synthesizer manufactured by the Roland Corporation between 1978 and 1981. It was notable as the company's first self-contained polyphonic synthesizer, and for employing digital control of analog circuits, allowing for such features as programmable memory, voice assignment modes, an arpeggiator, polyphonic portamento and others.

<span class="mw-page-title-main">MIDI keyboard</span> Piano-style keyboard that sends MIDI inputs to a computer or device

A MIDI keyboard or controller keyboard is typically a piano-style electronic musical keyboard, often with other buttons, wheels and sliders, used for sending Musical Instrument Digital Interface (MIDI) signals or commands over a USB or MIDI 5-pin cable to other musical devices or computers. MIDI keyboards lacking an onboard sound module cannot produce sounds themselves, however some models of MIDI keyboards contain both a MIDI controller and sound module, allowing them to operate independently. When used as a MIDI controller, MIDI information on keys or buttons the performer has pressed is sent to a receiving device capable of creating sound through modeling synthesis, sample playback, or an analog hardware instrument. The receiving device could be:

<span class="mw-page-title-main">Korg DW-8000</span> Hybrid digital-analog synthesizer

The Korg DW-8000 synthesizer is an eight-voice polyphonic hybrid digital-analog synthesizer 61-note keyboard instrument released in 1985. By the time of its launch, Korg had already begun a common trend in 1980s synthesizer design: using numerical codes to access or change parameters with its predecessor - the Korg Poly-61, which was widely regarded as the company's first "knobless" synthesizer. This was a move away from the heavily laden, complex control panels of earlier designs.

<span class="mw-page-title-main">Moog Source</span> Monophonic analog synthesizer

The Moog Source is a monophonic Z80 microprocessor-controlled analog synthesizer manufactured by Moog Music from 1981 to 1985. The Source was Moog's first synthesizer to offer patch memory storage. The design was also the first Moog synthesizer to feature a flat-panel membrane keyboard to replace the standard buttons, knobs and sliders, along with multihued panel graphics that were very different from anything Moog offered at the time. Sound wise it is considered to sound more like the original Moog Minimoog than any other synthesizer made by Moog and was introduced as its replacement.

The KORG Poly-61(PS-61) is an analogue programmable polyphonic synthesizer released by Korg in 1982, as a successor to the Polysix. It was notable for being Korg's first largely "knobless" synthesizer - featuring a push-button interface for programming, dispensing with the Polysix's knobs and switches. The Poly-61 also uses digitally-controlled analog oscillators or DCOs, in place of the Polysix's VCOs. The Poly-61 also boasted double the patch memory, but did not feature its predecessor's onboard effects.

<span class="mw-page-title-main">Korg MS2000</span> Synthesizer released in 2000

The Korg MS2000 is a virtual analog synthesizer produced by the Japanese electronic musical instrument manufacturer Korg.

<span class="mw-page-title-main">Oberheim OB12</span> Synthesizer released in 2000

The Oberheim OB•12 is a Virtual Analog synthesizer, designed and realised by the Italian musical instrument manufacturer Viscount, in production between 2000 and 2005.

<span class="mw-page-title-main">Kurzweil K2000</span> Digital synthesizer and music workstation by Kurzweil Music Systems

The Kurzweil K2000 is a digital synthesizer and music workstation produced by Kurzweil Music Systems between 1991 and 2000 in a variety of standard configurations, including rack-mountable versions and models that came with 16-bit user sampling.

The Roland JX-10 Super JX is a 12-voice analog synthesizer keyboard produced by Roland Corporation from 1986 to 1989, along with a rack-mounted version, the MKS-70. For nearly 30 years, it was the last true analog synthesizer made by Roland and has been critically acclaimed as one of their classic analog instruments. In 2015, Roland once again started producing analog synthesizers beginning with their JD-XA and JD-Xi keyboards as analog/digital crossover synthesizers. The design on the JX-10 is essentially two Roland JX-8P synthesizers put together, with a 76-note velocity-sensitive keyboard with aftertouch. It also includes features not found on the JX-8P, including a simple 1-track sketchbook sequencer and a delay effect. However, the JX-10 is not exactly the same as "two JX-8P's" because the chorus is not identical to the JX-8P. The JX-10 also has a slightly different amplifier section as well as different electronic components which further distinguish its sound from its predecessor, the JX-8P.

<span class="mw-page-title-main">Roland JX-8P</span>

Roland JX-8P is a 61-key, velocity- and aftertouch-sensitive, six-note polyphonic, almost entirely analog synthesizer released by Roland in 1985. In a time of rising popularity of digital frequency modulation synthesizers, such as Yamaha DX7, JX-8P was marketed as the best of both worlds: while it was possible to create classic analog synth sounds, several new modulation parameters and redesigned hardware enabled it to produce certain types of sounds associated with FM synthesis, such as metallic percussive sounds. Likewise, traditional hands-on controls were replaced with a Yamaha DX7-style interface with membrane buttons and one "edit" slider.

<span class="mw-page-title-main">Oberheim Xpander</span> Analogue synthesizer

The Oberheim Xpander is an analog synthesizer launched by Oberheim in 1984 and discontinued in 1988. It is essentially a keyboardless, six-voice version of the Matrix-12. Utilizing Oberheim's Matrix Modulation technology, the Xpander combined analog audio generation with the flexibility of digital controls logic.

The Kawai K5000 is a series of digital synthesizers / music workstation manufactured by Kawai Musical Instruments of Japan.

<span class="mw-page-title-main">Prophet '08</span> Synthesizer

The Prophet '08 is a polyphonic analog synthesizer created by Dave Smith of St. Helena, California, US, for Dave Smith Instruments (DSI), released in late 2007. As with DSI's other instruments, the Prophet '08 uses analog subtractive synthesis, as opposed to many of the current crop of synthesizers, which employ DSP-based virtual analog synthesis.

<span class="mw-page-title-main">Split-8</span> Polyphonic analogue synthesizer

The Split-8 is a polyphonic analogue keyboard synthesizer manufactured by Sequential Circuits. Built in Japan and going by the alternative name Pro-8 in some markets, this was one of the last synthesizers produced by the company and was assigned model number 608. It was released in 1985 at a list price of $1,199. This and some other Sequential Circuits synthesizers were built around the Curtis Electronics CEM 3394 "synth-on-a-chip" integrated circuit, and used a Z80 as their central microprocessor.

<span class="mw-page-title-main">Akai AX80</span> Analogue synthesizer

The AX80 is a polyphonic analogue keyboard synthesizer manufactured by Akai Professional in 1984. It was Akai's first venture into the professional electronic musical instrument market. The AX80 used digitally controlled oscillators (DCO) and filter circuitry based on the Curtis Electronics CEM 3372 integrated circuit. It was marketed as part of a line of project studio equipment called the Akai Music Studio System, which included the S612 digital sampler the MR16 drum machine, the MS08 sequencer, and the MG1212 multitrack tape recorder, at a price of $1,695 US.

<span class="mw-page-title-main">Akai AX60</span> Polyphonic analogue synthesizer

The AX60 is a polyphonic analogue keyboard synthesizer manufactured by Akai Professional in the mid-1980s. It was Akai's answer to the popular Roland Juno series synthesizers. The AX60 uses voltage-controlled analogue oscillators and filter circuitry based on the Curtis Electronics CEM 3394 integrated circuit.

<span class="mw-page-title-main">Casio CZ synthesizers</span> Family of synthesizers by Casio

The CZ series is a family of low-cost phase distortion synthesizers produced by Casio in the mid-1980s. Eight models of CZ synthesizers were released: the CZ-101, CZ-230S, CZ-1000, CZ-2000S, CZ-2600S, CZ-3000, CZ-5000, and the CZ-1. Additionally, the home-keyboard model CT-6500 used 48 phase distortion presets from the CZ line. The CZ synthesizers' price at the time of their introduction made programmable synthesizers affordable enough to be purchased by garage bands. Yamaha soon introduced their own low-cost digital synthesizers, including the DX-21 (1985) and Yamaha DX100, in light of the CZ series' success.