Air & Space 18A

Last updated
Air & Space 18A
Air Space 18A.JPG
Role Autogyro
Manufacturer Air and Space Manufacturing, Inc.
Designer Gilbert Devore
First flight 1964
Introduction 1965
StatusOut of production
Produced1965-2000
Number built68

The Air & Space 18A is a gyroplane that was manufactured in the central United States between 1965 and 2000.

Contents

The Air & Space 18A is one of the last three gyroplanes issued a Standard Airworthiness Certificate (September 1961) by the United States Federal Aviation Administration (FAA).

Development

Umbaugh Aircraft Corporation

Raymond E. Umbaugh, a manufacturer of agricultural fertilizer, founded Umbaugh Aircraft Corporation in Ocala, Florida, in 1957 to develop a gyroplane based on experience he acquired while modifying single-seat Bensen Gyrocopters. Gilbert Devore commenced the design of Umbaugh's tandem two-seat jump-takeoff gyroplane in 1958, basing the rotor system on that of the Sznycer Omega BS-12 helicopter. The prototype Umbaugh U-17, built by Fairchild Engine and Airplane Corporation of Hagerstown, Maryland, flew in August 1959. Further test flights were conducted by chief pilot Ken Hayden and former Pitcairn Autogiro Company pilot Slim Soule. The majority of the testing of the aircraft was done at Bartow Air Base in Bartow, Fl. The prototype exhibited stability problems due to its single rudder and minimal T-tail horizontal stabilizer positioned on a boom behind the pusher propeller. The second prototype, named Umbaugh U-18, was fitted with a V-tail which also proved inadequate. The third empennage tested, also unsuccessfully, was a T-tail with two large vertical end plates on the horizontal tail plane. Sufficient stability was finally achieved by the use of two fixed vertical fins with a centrally mounted all-flying rudder, all mounted on a horizontal stabilizer. Umbaugh had by this time concluded an agreement for Fairchild Engine and Airplane Corporation to undertake final development and mass production of the U-18 as the “Flymobil.”

Fairchild built five development gyroplanes during 1960, one of which was used to gain FAA Approved Type Certificate 1H17 in September 1961. Umbaugh established a large network of dealers and distributors in the United States, upon whom he imposed minimum sales quotas to generate a large order backlog, but he experienced difficulty filling the orders due to inadequate manufacturing capability at Fairchild. Under pressure from the dealers, Umbaugh Aircraft Corporation ceased operations in 1962 and the agreement with Fairchild was terminated.

Air and Space Manufacturing Inc.

About one hundred Umbaugh dealers took over the assets of Umbaugh Aircraft Corporation and in 1964 established Air and Space Manufacturing, Inc., of Muncie, Indiana, to commence production. In early 1965, the FAA awarded the corporation a production certificate for the Air & Space Model 18A gyroplane, a model which had only minor differences from the Umbaugh U-18. By late 1965 sixty-eight gyroplanes had been completed and delivered, 14 more were near completion, some were later stolen when Air and Space Manufacturing was in receivership. Air and Space Manufacturing, Inc., was again faced with dealer pressure for aircraft and commenced efforts to raise $2.5 million for expansion. The fund raising resulted in accusations of stock irregularities by the U.S. Securities and Exchange Commission, and though those concerned were eventually cleared of all charges, the associated costs and delays resulted in the collapse of the company in 1966.

The assets of Air and Space Manufacturing went into storage, and were eventually (in the 1980s) acquired by one of the dealers, retired Pan Am pilot I. Don Farrington of Paducah, Kentucky. John Potter, the former Vice President of Air & Space Manufacturing, Inc., went into partnership with Farrington. Their company, Farrington Aircraft, worked on acquiring existing Air & Space 18A airframes as well as the type certificate. The company closed shortly after Farrington suffered a heart attack in April 2000 (while flying a gyroplane at an air show) and died a few days after the resulting crash.

Potter tried to re-establish the 18A program and transported an inventory of parts and some 18As to LaBelle, Florida, where he and partner Gene Ferrel established Heliplane Aircraft International Corp. Robert Kelsall of Euroa, Australia, was engaged to design a four-place version of the 18A termed 28A. Potter died of cancer in 2006.

Heliplane Aircraft International Corp. currently resides in Summerville, SC outside Charleston. Gene Ferrel owns the FAA Type II certificate for this aircraft, along with three trailers full of parts, fuselages and airframes. As of November 2011, no progress has been made placing the 18A back into production.

Farrington Aircraft Corp.

Initially lacking ownership of the type certificate, Farrington Aircraft Corporation remanufactured existing aircraft and also developed Supplemental Type Certificate (STC) modifications including:

Farrington Aircraft Corporation also operated a gyroplane pilot training facility at Farrington Airpark, a privately owned, public-use airport in Paducah, Kentucky, and engaged in extensive promotional efforts.


Production by Air and Space America, Inc.

In 1991, Farrington obtained the Air & Space 18A Type Certificate, and undertook efforts to manufacture new gyroplanes as Air and Space America, Inc. with a selling price of $75,000. [1] Work was also under way in 1996 to certify a Model 20A, fitted with a Lycoming IO-360 200 horsepower (150 kW) fuel-injected engine.

Farrington suffered a heart attack in April 2000 (while flying an Air and Space 18A at an airshow) and died a few days after the subsequent crash. Farrington Aircraft Corporation ceased operations shortly after, and the gyroplane assets were sold at auction.

Heliplane Aircraft Corporation International

Heliplane Aircraft Corporation International purchased the type certificate (TC) and assets and expressed an intent to start manufacturing the 18A by 2015. The TC was transferred on July 21, 2011 per FAA TCDS database. The TC along with several aircraft were moved to Fort Pierce, Florida; the owner of HACI is Eugene Ferrel. Plans to fit the 18A with a DeltaHawk 200 hp diesel engine never materialized beyond the planning stage and the company has done little else. HACI filed for Chapter 11 Bankruptcy Protection on July 1, 2011. The Bankruptcy court has since converted the case to Chapter 7 and the type certificate and all assets are being liquidated.

Heliplane USA

Based on earlier writings, Thomas W McClelland formed Heliplane USA and purchased the TC and assets, however there is no record of this on the FAA TCDS database.

TWMCC Leasing, LLC

Type Certificate 1H17, Rev 6 was transferred from Heliplane Aircraft Corporation International to TWMCC Leasing, LLC as of December 12, 2012 per FAA TCDS database search on March 26, 2021. The address associated with the TC record is still on Airman's Drive in Ft. Pierce, FL.


Design

External videos
Nuvola apps kaboodle.svg Jump takeoff of A&S 18A

The 18A is a metal semi-monocoque construction with a tube frame supporting the transmission and engine. It has an enclosed cockpit with two tandem seats and a fixed tricycle landing gear. A 180 hp (134 kW) Lycoming O-360-A1D horizontally opposed carbureted engine is fitted behind the cockpit driving a two or three-bladed Hartzell pusher propeller. A three-bladed fully articulated rotor is mounted above and behind the cockpit. A hydraulically actuated clutch and a transmission are provided to permit the engine to drive the rotor briefly while on the ground to obtain the rotor speed necessary for takeoff. The clutch is released immediately prior to takeoff, and the rotor is not engine-driven in flight. The rotor can be pre-spun up to 370 rpm on the ground with the blades in flat pitch to store energy for take-off (flight rpm typically being in the low 200s). When the blades are released to flight pitch the aircraft can perform a "jump" or zero-roll take-off (aircraft load and density altitude permitting) using the excess energy in the blades.

Specifications (18A)

Data from Jane's All The World's Aircraft 1966–67 [2] and Report UER 18-600 FAA Approved Gyroplane Flight Manual, Revised Apr. 9, 1991

General characteristics

Performance

Related Research Articles

<span class="mw-page-title-main">Autogyro</span> Rotorcraft with unpowered rotor

An autogyro, or gyroplane, is a class of rotorcraft that uses an unpowered rotor in free autorotation to develop lift. While similar to a helicopter rotor in appearance, the autogyro's unpowered rotor disc must have air flowing upward across it to make it rotate.

<span class="mw-page-title-main">MBB/Kawasaki BK 117</span> German/Japanese utility helicopter

The MBB/Kawasaki BK 117 is a twin-engined light utility–transport helicopter. It was jointly developed and manufactured by Messerschmitt-Bölkow-Blohm (MBB) of Germany and Kawasaki of Japan. MBB was later purchased by Daimler-Benz and eventually became a part of Eurocopter, which was later rebranded as Airbus Helicopters.

<span class="mw-page-title-main">Sikorsky S-76</span> American medium-size commercial utility helicopter

The Sikorsky S-76 is a medium-size commercial utility helicopter designed and produced by the American helicopter manufacturer Sikorsky Aircraft. It is the company's first helicopter specifically developed for the civilian market.

<span class="mw-page-title-main">Robinson R22</span> American helicopter model

The Robinson R22 is a two-seat, two-bladed, single-engined, light utility helicopter manufactured by Robinson Helicopter Company. It was designed in 1973 by Frank D. Robinson, and has been in production since 1979.

<span class="mw-page-title-main">Bell 222/230</span> Family of utility helicopters

The Bell 222 is an American twin-engine light helicopter built by Bell Helicopter. The Bell 230 is an improved development with different engines and other minor changes.

<span class="mw-page-title-main">Light-sport aircraft</span> Category of lightweight aircraft that are simple to fly

A light-sport aircraft (LSA), or light sport aircraft, is a fairly new category of small, lightweight aircraft that are simple to fly. LSAs tend to be heavier and more sophisticated than ultralight aircraft, but LSA restrictions on weight and performance separates the category from established GA aircraft. There is no standard worldwide description of an LSA.

<span class="mw-page-title-main">Schweizer S300</span> Helicopter model

The Schweizer S300 series family of light utility helicopters was originally produced by Hughes Helicopters, as a development of the Hughes 269. Later manufactured by Schweizer Aircraft, and currently produced by Schweizer RSG, the basic design has been in production for over 50 years. The single, three-bladed main rotor and piston-powered S300 is mostly used as a cost-effective platform for training and agriculture.

<span class="mw-page-title-main">Piper PA-31 Navajo</span> Family of twin engine aircraft built 1967–1984

The Piper PA-31 Navajo is a family of twin-engined utility aircraft designed and built by Piper Aircraft for small cargo and feeder airlines, and as a corporate aircraft. Production ran from 1967 to 1984. It was license-built in a number of Latin American countries.

<span class="mw-page-title-main">Hughes TH-55 Osage</span> Piston-powered light training helicopter produced for the United States Army

The Hughes TH-55 Osage is a piston-powered light training helicopter produced for the United States Army. It was also produced as the Model 269 family of light utility helicopters, some of which were marketed as the Model 300. The Model 300C was produced and further developed by Schweizer after 1983.

<span class="mw-page-title-main">Gyrodyne</span> Type of VTOL aircraft

A gyrodyne is a type of VTOL aircraft with a helicopter rotor-like system that is driven by its engine for takeoff and landing only, and includes one or more conventional propeller or jet engines to provide forward thrust during cruising flight. During forward flight the rotor is unpowered and free-spinning, like an autogyro, and lift is provided by a combination of the rotor and conventional wings. The gyrodyne is one of a number of similar concepts which attempt to combine helicopter-like low-speed performance with conventional fixed-wing high-speeds, including tiltrotors and tiltwings.

<span class="mw-page-title-main">Fairchild Hiller FH-1100</span> Type of aircraft

The Fairchild Hiller FH-1100 is a single-engine, single two-bladed rotor, light helicopter designed and produced by the American aircraft manufacturer Fairchild Hiller.

<span class="mw-page-title-main">Eurocopter AS355 Écureuil 2</span> Type of aircraft

The EurocopterAS355 Écureuil 2 is a twin-engine light utility helicopter developed and originally manufactured by Aérospatiale in France

<span class="mw-page-title-main">McCulloch J-2</span> Type of aircraft

The McCulloch J-2 was a small, two-seat autogyro with an enclosed cabin, one of only three designs of this type of aircraft to receive a type certificate in the United States. It was built by McCulloch Aircraft Corporation.

<span class="mw-page-title-main">Enstrom F-28</span> Light, piston-powered helicopter family

The Enstrom F-28 and 280 are a family of small, light piston engine powered helicopters produced by the Enstrom Helicopter Corporation.

<span class="mw-page-title-main">Rockwell Commander 112</span> Type of aircraft

The Rockwell Commander 112 is an American four-seat single-engined general aviation aircraft designed and built by North American Rockwell starting in 1972. In 1976, they introduced the turbocharged version 112TC and mounting a larger engine with other minor improvements they introduced the Rockwell Commander 114. A total of approximately 1,300 examples of all models were produced before the production line shut down in 1980. In 1981, the type certificate owner was Gulfstream Aerospace, but that company had no interest in single-engine piston production.

The Honeywell HTS900 is an American turboshaft engine produced by Honeywell Aerospace. A growth version of the LTS101 which it is designed to replace, the HTS900 is in the 1,000 shp (745 kW) class.

The Lycoming O-233 is a four-cylinder, air-cooled, horizontally opposed piston aircraft engine that was built by Lycoming Engines between 1940 and 1944.

<span class="mw-page-title-main">Avian Gyroplane</span> Type of aircraft

The Avian 2/180 Gyroplane was a two-seat, single-engine autogyro built in Canada in the 1960s. Several prototypes were built but production was not achieved.

<span class="mw-page-title-main">Skyworks Aeronautics</span> American autogyro research and development company

Skyworks Aeronautics Corp., formerly Groen Brothers Aviation, Inc., Groen Aeronautics Corporation and Skyworks Global, is an American autogyro research and development company based in Chicago. The company was founded in 1986 by David Groen and his late brother Jay Groen in Salt Lake City, Utah. David Groen remains as Senior Advisor.

The Calumet Snobird Explorer was an American autogyro designed and produced by Calumet Motorsports of Lansing, Illinois, introduced in May 1997. Now out of production, when it was available, the aircraft was supplied as a kit for amateur construction.

References

  1. Flying Magazine: 34. August 1991.{{cite journal}}: CS1 maint: untitled periodical (link)
  2. Taylor 1966, p. 182.