JBL Paragon

Last updated

The JBL Paragon, measuring almost 9 feet (2.7 m) from left to right JBL Paragon (edited and cropped).jpg
The JBL Paragon, measuring almost 9 feet (2.7 m) from left to right

The JBL D44000 Paragon is a one-piece stereo loudspeaker created by JBL that was introduced in 1957 and discontinued in 1983; its production run was the longest of any JBL speaker. [1] At its launch, the Paragon was the most expensive domestic loudspeaker on the market. [2]

Contents

Designed by Arnold Wolf from a concept elaborated by Richard Ranger, it is almost 9 feet (2.7 m) long and requires over a hundred-man hours of hand-finishing by a team of dedicated craftsmen. [1] Resembling less a conventional loudspeaker than an elegant sideboard, [3] it is a landmark product for the company that was sought after by the well-heeled and by celebrities. [4] With an estimated total production of about 1,000 units, it is highly sought after by collectors to this day. [1]

History

The Paragon is a horn-loaded, stereo speaker system within a single 9-foot-wide (2.7 m) housing. [3] It is based on a diffusion principle developed by Richard Ranger as consultant to JBL. Launched in 1957, the Paragon is the world's earliest production stereo loudspeaker for home use, [5] and also the most expensive speaker at the time. [2] As the flagship JBL product, it cost $1,830 (£650) equivalent to $19,900in 2023. [3] The "Paragon" is the product with the longest production run of all JBL loudspeakers. [1] It was produced continually until it was discontinued in 1983, when it was replaced by a product line named "Everest". [2] [4]

Design

horizontal cross section of a Paragon unit, with labels showing the individual components Paragon section.jpg
horizontal cross section of a Paragon unit, with labels showing the individual components

Since even the early days of stereophonic sound, designers were faced with the issue of directionality and the listener who was not located exactly in between the two speaker units. Col. Richard R. Ranger, a pioneer of stereophonic sound in the film industry, conceptualised the solution to the problem of reproducing stereo sound for all and not just the centrally-positioned listener. He devised a loudspeaker system where the sound from the speaker drive units would be reflected against curved surfaces (wood panels) within a cabinet to create a wide, uniform stereo image that would hold stable in any location within the listening room. Ranger elaborates on the JBL-Ranger Radial Refraction system of stereophonic reproduction thus: [1]

... only along this axis of symmetry that the two speakers have consistently equal effect. As soon as the listener moves off axis, the speaker toward which he moves takes predominance. Sound intensity decreases rapidly with distance and the more distant speaker quickly loses out to the nearer.

This can be avoided by projecting the sound from each speaker against a curved surface which acts as a convex lens for the sound and directs it more strongly to the side opposite the speaker than it does to its own side. The convex refractor thus eliminates the sharp axis of symmetry where the slightest movement of the listener is so disturbing.

In the listening area in front of the integrated speaker system, the energy from the two stereo channels builds up a full front of sound which can readily be appreciated by more than one person. So the axis of symmetry no longer exerts its unstable equilibrium on the critical listener.

The term "unstable equilibrium" is not mere whimsy. In stereo reproduction, it is customary for the soloist to appear in the center. Then, certain sections of the accompanying music are positioned right or left; but it is most important that wherever they are, they STAY THERE. Uncertain movement of the apparent sound source gives a very queasy feeling.

Once it became possible to hold monaural sound to the center, it was found that with regular stereo everything fell into its proper place ... A whole curtain of sound was opened up.

Ranger's 9-foot prototype of the product, with plenty of right angles and shiny black Micarta skin, was bulky, imposing, and visually unattractive. [6] Arnold Wolf was called in as the industrial design consultant to this project in early 1957. [1] Wolf, who would later become president and chief executive of JBL, was initially asked to produce a shell version for dealers' shops. Due to transportation and installation constraints, it was decided that the speaker would be split into three components – the left and right channel enclosures, and the curved radiator panel – that could be easily re-assembled with a screwdriver. [6] To support the weight and prevent deforming, the design called for six feet, of which four are height-adjustable. [5] Instead of producing detailed drawings, Wolf worked with scale models. [5] First, he created a 1:4 model in plastic, after which he made others. He ended with a 1:12 scale model that would show how it could be disassembled and reassembled. [5] [6] During the design phase, the relationship between Wolf and Ranger became very tense, and the project nearly collapsed. [5] The parties came together over the month of June, and agreed on the definitive production specification for the Paragon. This would be a 2-way design. [5]

Construction

Frontal aspects of a JBL Paragon
Paragon leg.jpg
Sculpted leg
Paragon horn1.jpg
Horn (375 Compression driver)

As can be seen from the diagram, the unusual shape of the Paragon made it very complicated to build. [1] Engineering and factory translated the design into one executable on the shop floor. After overcoming the manufacturing challenges posed by the curved refractor panels and the cabinet legs, the speaker entered production in late 1957. [6]

Rear view of a JBL Paragon
Paragon ring radiator.jpg
075 Ring radiator, from rear
Paragon terminals.jpg
Connector terminals

The Paragon much resembles a sideboard, measures 106 × 33.75 × 24.5 inches (269 × 86 × 62 cm), and weighs 850 pounds (390 kg) according to the product brochure. [3] Standard finishes include korina, birch, mahogany and ebony; premium wood finishes included light and dark walnut, oak, teak, rosewood; [3] a piano lacquer finish would cost extra. [1] A team of six worked on each unit, spending an estimated 112 to 125-man-hours to complete a single unit, [1] [5] most of it spent on finishing of the woodwork. After assembly, eight hours would be needed just for sanding down the entire enclosure. Then, several coats of varnish are applied by hand, allowed to dry, and then smoothed down by further rubbing. [1]



Product revisions

Product brochure from JBL Paragon.jpg
Product brochure from JBL

The components used in the Paragon went through numerous changes over the years. [1]

  • 1957 Paragon 44000 launched ("domestic" and "industrial" variants).
  • Early 1960s the 150-4C bass driver replaced by the LE15A.
  • Early 1960s SE408S power amplifier launched, and available for integration with Paragon as powered speakers (removed by the 1970s).
  • 1979 use the new drivers employing ferrite magnets instead of Alnico V – the LE15A bass driver replaced by the ferrite LE15H; the 375 midrange driver replaced with the Alnico 376.
  • 1983 Paragon discontinued.

Reception

Partick Vercher at L'Audiophile said that the ideal listening position is at least 3 metres away, and 4050 cm lower than a normal seated position; alternatively the speaker needs to be hoisted up by that amount for a comfortable sound. The sound itself is described as possessing "unshakeable dynamics" when turned up loud, pacey without any sign of fatiguing distortion, and with an impressive separation of instruments. [5] Sonic Flare describes the sound of the Paragon as possessing well-integrated "liquid highs, excellent midrange and bass", and proverbially worth dying for. There are rumours that Frank Sinatra and Dean Martin acquired three Paragons each – one for each of left, center and right channels – with which they used to monitor their recordings from master tapes. [4]

Only about a thousand units were ever produced over its 25-year life. At the height of production, five units left the factory each week. [1] In 2000, units in mint condition would fetch upwards of $20,000 on the second hand market. [1] [3] [Note 1] It has featured in museum exhibitions, namely one held at Los Angeles County Museum of Art in 2011–12 entitled "California Design, 1930–1965: Living in a Modern Way." [7]

Spin-offs and legacy

In 1960, JBL launched a smaller and less elaborate 3-way sideboard speaker, measuring 73.7 × 30 × 22.5 inches (187 × 76 × 57 cm), named the "C45 Metregon". [8] Self powered Paragons and Metregons employing the JBL SE-408S stereo amplifier were optional. A miniature version, the C46 Minigon was also available in the early 1960s. [5] [9]

Notes

  1. Info: December 2013 sale of JBL Paragon (C44) legendary speaker in very nice condition Asking Price: USD $26250.00

Related Research Articles

<span class="mw-page-title-main">High fidelity</span> High-quality reproduction of sound

High fidelity is the high-quality reproduction of sound. It is popular with audiophiles and home audio enthusiasts. Ideally, high-fidelity equipment has inaudible noise and distortion, and a flat frequency response within the human hearing range.

<span class="mw-page-title-main">Loudspeaker</span> Converts an electrical audio signal into a corresponding sound

A loudspeaker is an electroacoustic transducer that converts an electrical audio signal into a corresponding sound. A speaker system, also often simply referred to as a speaker or loudspeaker, comprises one or more such speaker drivers, an enclosure, and electrical connections possibly including a crossover network. The speaker driver can be viewed as a linear motor attached to a diaphragm which couples that motor's movement to motion of air, that is, sound. An audio signal, typically from a microphone, recording, or radio broadcast, is amplified electronically to a power level capable of driving that motor in order to reproduce the sound corresponding to the original unamplified electronic signal. This is thus the opposite function to the microphone; indeed the dynamic speaker driver, by far the most common type, is a linear motor in the same basic configuration as the dynamic microphone which uses such a motor in reverse, as a generator.

<span class="mw-page-title-main">Surround sound</span> System with loudspeakers that surround the listener

Surround sound is a technique for enriching the fidelity and depth of sound reproduction by using multiple audio channels from speakers that surround the listener. Its first application was in movie theaters. Prior to surround sound, theater sound systems commonly had three screen channels of sound that played from three loudspeakers located in front of the audience. Surround sound adds one or more channels from loudspeakers to the side or behind the listener that are able to create the sensation of sound coming from any horizontal direction around the listener.

<span class="mw-page-title-main">Monaural</span> Sound intended to be heard as if it were emanating from one position

Monaural or monophonic sound reproduction is sound intended to be heard as if it were emanating from one position. This contrasts with stereophonic sound or stereo, which uses two separate audio channels to reproduce sound from two microphones on the right and left side, which is reproduced with two separate loudspeakers to give a sense of the direction of sound sources. In mono, only one loudspeaker is necessary, but, when played through multiple loudspeakers or headphones, identical signals are fed to each speaker, resulting in the perception of one-channel sound "imaging" in one sonic space between the speakers. Monaural recordings, like stereo ones, typically use multiple microphones fed into multiple channels on a recording console, but each channel is "panned" to the center. In the final stage, the various center-panned signal paths are usually mixed down to two identical tracks, which, because they are identical, are perceived upon playback as representing a single unified signal at a single place in the soundstage. In some cases, multitrack sources are mixed to a one-track tape, thus becoming one signal. In the mastering stage, particularly in the days of mono records, the one- or two-track mono master tape was then transferred to a one-track lathe used to produce a master disc intended to be used in the pressing of a monophonic record. Today, however, monaural recordings are usually mastered to be played on stereo and multi-track formats, yet retain their center-panned mono soundstage characteristics.

<span class="mw-page-title-main">Horn loudspeaker</span> Loudspeaker using an acoustic horn

A horn loudspeaker is a loudspeaker or loudspeaker element which uses an acoustic horn to increase the overall efficiency of the driving element(s). A common form (right) consists of a compression driver which produces sound waves with a small metal diaphragm vibrated by an electromagnet, attached to a horn, a flaring duct to conduct the sound waves to the open air. Another type is a woofer driver mounted in a loudspeaker enclosure which is divided by internal partitions to form a zigzag flaring duct which functions as a horn; this type is called a folded horn speaker. The horn serves to improve the coupling efficiency between the speaker driver and the air. The horn can be thought of as an "acoustic transformer" that provides impedance matching between the relatively dense diaphragm material and the less-dense air. The result is greater acoustic output power from a given driver.

<span class="mw-page-title-main">JBL</span> American audio hardware manufacturer

JBL is an American audio equipment manufacturer headquartered in Los Angeles, California, United States. JBL serves the customer home and professional market. The professional market includes studios, installed/tour/portable sound, music production, DJ, cinema markets. The home market includes high-end home amplification/speakers/headphones as well as high-end car audio. JBL is owned by Harman International, itself a subsidiary of Samsung Electronics.

<span class="mw-page-title-main">Stereophonic sound</span> Method of sound reproduction using two audio channels

Stereophonic sound, or more commonly stereo, is a method of sound reproduction that recreates a multi-directional, 3-dimensional audible perspective. This is usually achieved by using two independent audio channels through a configuration of two loudspeakers in such a way as to create the impression of sound heard from various directions, as in natural hearing.

Harman Kardon is a division of US-based Harman International Industries, an independent subsidiary of Samsung Electronics. Harman Kardon was originally founded in Westbury, New York, in 1953 by business partners Sidney Harman and Bernard Kardon.

Celestion is a British designer and exporter of professional loudspeakers.

<span class="mw-page-title-main">Rudy Bozak</span> American audio engineer

Rudolph Thomas Bozak (1910–1982) was an audio electronics and acoustics designer and engineer in the field of sound reproduction. His parents were Bohemian Czech immigrants; Rudy was born in Uniontown, Pennsylvania. Bozak studied at Milwaukee School of Engineering; in 1981, the school awarded him an honorary doctorate in engineering. Bozak married Lillian Gilleski; the two had three daughters: Lillian, Mary and Barbara.

<span class="mw-page-title-main">Powered speakers</span> Loudspeaker that have built-in amplifiers

Powered speakers, also known as self-powered speakers and active speakers, are loudspeakers that have built-in amplifiers. Powered speakers are used in a range of settings, including in sound reinforcement systems, both for the main speakers facing the audience and the monitor speakers facing the performers; by DJs performing at dance events and raves; in private homes as part of hi-fi or home cinema audio systems and as computer speakers. They can be connected directly to a mixing console or other low-level audio signal source without the need for an external amplifier. Some active speakers designed for sound reinforcement system use have an onboard mixing console and microphone preamplifier, which enables microphones to be connected directly to the speaker.

<span class="mw-page-title-main">Studio monitor</span> Speaker designed to reproduce sound accurately

Studio monitors are loudspeakers in speaker enclosures specifically designed for professional audio production applications, such as recording studios, filmmaking, television studios, radio studios and project or home studios, where accurate audio reproduction is crucial. Among audio engineers, the term monitor implies that the speaker is designed to produce relatively flat (linear) phase and frequency responses. In other words, it exhibits minimal emphasis or de-emphasis of particular frequencies, the loudspeaker gives an accurate reproduction of the tonal qualities of the source audio, and there will be no relative phase shift of particular frequencies—meaning no distortion in sound-stage perspective for stereo recordings. Beyond stereo sound-stage requirements, a linear phase response helps impulse response remain true to source without encountering "smearing". An unqualified reference to a monitor often refers to a near-field design. This is a speaker small enough to sit on a stand or desk in proximity to the listener, so that most of the sound that the listener hears is coming directly from the speaker, rather than reflecting off walls and ceilings. Monitor speakers may include more than one type of driver or, for monitoring low-frequency sounds, such as bass drum, additional subwoofer cabinets may be used.

The Trifield process is a form of audio rendering in which a conventional two-channel signal is decoded to an additional number of loudspeakers, typically three in the form of a Left-Centre-Right front stage. The technique provides significant additional image stability, especially when the listener is moving or off-axis.

<span class="mw-page-title-main">Line array</span> Loudspeaker system composed of linearly-mounted, in-phase speakers

A line array is a loudspeaker system that is made up of a number of usually identical loudspeaker elements mounted in a line and fed in phase, to create a near-line source of sound. The distance between adjacent drivers is close enough that they constructively interfere with each other to send sound waves farther than traditional horn-loaded loudspeakers, and with a more evenly distributed sound output pattern.

Ambiophonics is a method in the public domain that employs digital signal processing (DSP) and two loudspeakers directly in front of the listener in order to improve reproduction of stereophonic and 5.1 surround sound for music, movies, and games in home theaters, gaming PCs, workstations, or studio monitoring applications. First implemented using mechanical means in 1986, today a number of hardware and VST plug-in makers offer Ambiophonic DSP. Ambiophonics eliminates crosstalk inherent in the conventional stereo triangle speaker placement, and thereby generates a speaker-binaural soundfield that emulates headphone-binaural sound, and creates for the listener improved perception of reality of recorded auditory scenes. A second speaker pair can be added in back in order to enable 360° surround sound reproduction. Additional surround speakers may be used for hall ambience, including height, if desired.

The sweet spot is a term used by audiophiles and recording engineers to describe the focal point between two speakers, where an individual is fully capable of hearing the stereo audio mix the way it was intended to be heard by the mixer. The sweet spot is the location which creates an equilateral triangle together with the stereo loudspeakers, the stereo triangle. In the case of surround sound, this is the focal point between four or more speakers, i.e., the location at which all wave fronts arrive simultaneously. In international recommendations the sweet spot is referred to as reference listening point.

<span class="mw-page-title-main">Altec Lansing Duplex</span> Line of loudspeakers

DUPLEX was the trade name given by Altec Lansing to its line of coaxial loudspeakers, beginning with the first model 601 in 1943. However, the name was most commonly associated with the subsequent model 604 which was a seminal loudspeaker that became a milestone in loudspeaker development. Well over a dozen different models carried the Duplex name over a near 50-year period. The vast majority consisted of a high frequency (HF) compression driver mounted to the back of a large diameter paper cone low frequency (LF) driver. However, there were also a few models with small diameter LF cones and direct radiator tweeters.

Colin Whatmough was a creator of loudspeaker designs and the proprietor of Whatmough Monitors, an Australian manufacturer of audio equipment.

<span class="mw-page-title-main">Arnold Wolf</span> American industrial designer (1927–2013)

Arnold Wolf was an American industrial designer and principal of Arnold Wolf Associates who was responsible for a number of loudspeaker designs for his client, audio manufacturers JBL. He was its president and chief executive from 1969 to 1980.

<span class="mw-page-title-main">Quad Electrostatic Loudspeaker</span> First production electrostatic loudspeaker

The Quad Electrostatic Loudspeaker (ESL) is the world's first production full-range electrostatic loudspeaker, launched in 1957 by Quad Electroacoustics, then known as the Acoustical Manufacturing Co. Ltd. The speaker is shaped somewhat like a home electric radiator curved slightly on the vertical axis. They are widely admired for their clarity and precision, but known to be difficult speakers to run and maintain.

References

  1. 1 2 3 4 5 6 7 8 9 10 11 12 13 "Paragon". Audio Heritage.
  2. 1 2 3 "Whatmough Paragon". Australian Hi-fi via courtesy link by Whatmough Audio.
  3. 1 2 3 4 5 6 Everard, Andrew (30 April 2013). "Arnold Wolf, 1927–2013: from JBL's monster Paragon to the best selling speaker of the 1970s", What Hi-Fi?
  4. 1 2 3 Kaey, Danny (10 September 2006). "Hi-Fi reviews, audio events, show coverage, photos and more JBL Everest DD66000". SonicFlare.
  5. 1 2 3 4 5 6 7 8 9 Vercher, Patrick (May 1990). "L'enceinte JBL Paragon" Archived 1 February 2014 at the Wayback Machine . L'Audiophile, N°10, pages 2632 (Courtesy link by Societatea Romana a Radioamatorilor). (in French)
  6. 1 2 3 4 "The Paragon". Audio Heritage.
  7. "Arnold Wolf, fomer head of JBL audio, dies" Archived 1 February 2014 at the Wayback Machine . Monterey Herald, 26 April 2013
  8. "1960 C45 METREGON". Lansing Heritage.
  9. "JBL Paragon". The Vintage Knob. January 2007.