Sound follower

Last updated

A sound follower, also referred to as separate magnetic, sepmag, magnetic film recorder, or mag dubber, is a device for the recording and playback of film sound that is recorded on magnetic film. [1] [2] This device is locked or synchronized with the motion picture film containing the picture. It operates like an analog reel-to-reel audio tape recording, but using film, not magnetic tape. The unit can be switched from manual control to sync control, where it will follow the film with picture. [3]

Contents

Magna Tech electronic film recorders and reproducer, sepmag Sound follower magnatech.JPG
Magna Tech electronic film recorders and reproducer, sepmag

Operation

A sound follower to the left of a shadow telecine Shadow telecine (6498603509).jpg
A sound follower to the left of a shadow telecine

Many motion picture cameras do not record audio sound on the film, so in professional film production, there is a need to have the sound recorded and played back on a device that has a double-system recording to tapes, or by any means, for example DAT or Nagra, SD or other audio recording media and then transferred to 16 mm or 35 mm sprocketed magnetic film. The sound recording would then be synchronized with a movie projector [4] or a telecine. Either 35 mm or 16 mm film that is fully coated with a magnetic material can be locked, sprocket hole by sprocket hole, to the film with the picture image. On the set, a clapperboard is used to mark the spot where the sound and picture will later be aligned in editing. [5]

Typical sound followers lock to the power line using a sync motor and toothed timing belts, or by using 240  Hz bi-phase interlocking pulse signals to sync sound to film. [6] The 240 Hz bi-phase is ten times the 24-frame rate. [7] Sound followers are found in many post-production studios for record and playback and in movie theater for sound playback. [8] In telecine use, the 24 frames per second is slowed to 23.976 frames/s to lock to SDTV and some HDTV standards, thus the digital bi-phase pulse is 239.76 Hz. [9]

The average feature film requires a large amount of 35 mm film. One second of 35 mm film uses 1.5 feet of film, moving at 18 inches per second (46 cm/s). One minute of film uses 90 feet (27.4 m), and one hour uses 5,400 feet (1.6 km). So, a two-hour movie with previews uses 11,250 feet or 2.13 miles (3.43 km) of film. For 16 mm film, these numbers are all divided by 2.5 (36 ft/min.). Because a two-hour movie is so long, the whole is divided onto five or six reels. While a film projector uses an intermittent mechanism to play the film, a sound follower and most telecines use continuous motion. [10]

By having the sound and picture sync this way this clearly saves the expense and time of making an optical print or magnetic sound track strip on the edge of the film. [11] The Sepmag would follow a projector or a telecine or a hand-cranked or motorized film viewer on a workbench. The sepmag sound follower would stay in sync with the film. In post-production work, a dubbed sound track of sound effects, or a second language, could be added to other channels of the sepmag. [12]

Sepmag had different record head configurations. A device could have a single mono track, dual two track or 4 track. The tracks are very large and the magnetic film moving at the normal speed of 24 frames per second, gave very good sound reproduction. [13] As such, a mixing studio would have many units, to mix all the sound and effect down to 4, 2 and one track as needed. [14] [15]

Magnetic film used is 3 to 5 mils thick, the same as the picture film, so the picture and sound have equal diameters on the film reels. The magnetic film has magnetic oxide coating on the complete width of the film. [14] and the standard monaural track in 16 mm and 35 mm is 200 mils wide. 35 mm mag films may not be fully coated, but "striped" to permit editing marks to show through both sides. The first films used were acetate base till 1970, then replaced by polyester base. Acetate base is unstable, can have degradation, the ferric oxide coating and the Acetate base can cause vinegar degradation. [16] [17]

In 1914, the first SEPMAG patent was filed. In 1929, the first sound follower was on the market and by 1941, AC biasing models were sold, giving better sound quality. [18] The Stille SEPMAG transport was one of the first SEPMAG systems. [19] Some of the older sound followers' interlock speeds were too slow to keep up with the high speed shuttle speeds of modern telecines; therefore, some 240 Hz bi-phase buffers were made to help solve this problem.

Models

The major makers of sound followers are M.T.E.'s Magna Tech, [20] RCA, and Sondor. Models can come in playback-only model or record-and-playback. Models can have the option of changing the number of tracks. Some are equipped with dual sets of sprockets that can use more than one size of magnetic film, 16 mm or 35 mm. [21]

Alternate uses

Sound followers were also used in the 1960s strictly for audio recording & record album mastering, for the magnetic film format at the time had several advantages over standard magnetic recording tape. Magnetic film's extra thickness over tape made it less susceptible to "print-through", and its sprocket-driven nature made it less likely to suffer from tape flutter and other speed variations. Command Records in the 1960s released several albums that were recorded and mastered on 35 mm magnetic film for several artists on the label, such as Enoch Light, Tony Mottola, and others.

It is generally accepted that Everest Records subsidiary of the Belock Instrument Corporation based in College Point New York pioneered the use of three channel 35 mm magnetic film from around 1959. When the company transferred to Hollywood under new ownership in 1961 the Everest Bayside Recording Studio was sold and the 35 mm equipment to Mercury Records and later Command Classics. Improvements in standard tape technology and the high cost of the 35 mm process led to its discontinuance.[ citation needed ]

Fate

Sound followers are not used for most new film productions (the major exception being IMAX). Sound followers are still in use, as there are many separate magnetic films in film vaults. Reel-to-reel tape, then later hard disk drive and solid-state drive recording system replaced sound followers.

See also

Related Research Articles

<span class="mw-page-title-main">Magnetic tape</span> Medium used to store data in the form of magnetic fields

Magnetic tape is a medium for magnetic storage made of a thin, magnetizable coating on a long, narrow strip of plastic film. It was developed in Germany in 1928, based on the earlier magnetic wire recording from Denmark. Devices that use magnetic tape could with relative ease record and playback audio, visual, and binary computer data.

<span class="mw-page-title-main">Tape recorder</span> Machine for recording sound

An audio tape recorder, also known as a tape deck, tape player or tape machine or simply a tape recorder, is a sound recording and reproduction device that records and plays back sounds usually using magnetic tape for storage. In its present-day form, it records a fluctuating signal by moving the tape across a tape head that polarizes the magnetic domains in the tape in proportion to the audio signal. Tape-recording devices include the reel-to-reel tape deck and the cassette deck, which uses a cassette for storage.

<span class="mw-page-title-main">Nagra</span> Series of audio recorders produced by Kudelski SA

Nagra is a brand of portable audio recorders produced from 1951 in Switzerland. Beginning in 1997 a range of high-end equipment aimed at the audiophile community was introduced, and Nagra expanded the company's product lines into new markets.

Pilottone and the related neo-pilotone are special synchronization signals recorded by analog audio recorders designed for use in motion picture production, to keep sound and film recorded on separate media synchronised. Before the adoption of timecode by the motion picture industry, pilotone sync was used in almost all 1/4-inch magnetic double system motion picture sound recording from the late 50s until the late 1980s. Previous to the introduction of 1/4-inch audio tape recordings were made on 35mm optical cameras and then later, with the introduction of magnetic recording, 16mm or 35mm magnetic stock. The first 1/4-inch recorder capable of recording a synch track to regulate the playback speed of the recording was made by Rangertone and was a variation on the soon to come pilotone system.

<span class="mw-page-title-main">Ampex</span> American company that pioneered the use of videotape

Ampex Data Systems Corporation is an American electronics company founded in 1944 by Alexander M. Poniatoff as a spin-off of Dalmo-Victor. The name AMPEX is a portmanteau, created by its founder, which stands for Alexander M. Poniatoff Excellence. Ampex operates as Ampex Data Systems Corporation, a subsidiary of Delta Information Systems, and consists of two business units. The Silicon Valley unit, known internally as Ampex Data Systems (ADS), manufactures digital data storage systems capable of functioning in harsh environments. The Colorado Springs, Colorado, unit, referred to as Ampex Intelligent Systems (AIS), serves as a laboratory and hub for the company's line of industrial control systems, cyber security products and services and its artificial intelligence/machine learning technology.

<span class="mw-page-title-main">Reel-to-reel audio tape recording</span> Audio recording using magnetic tape spooled on open reels

Reel-to-reel audio tape recording, also called open-reel recording, is magnetic tape audio recording in which the recording tape is spooled between reels. To prepare for use, the supply reel containing the tape is placed on a spindle or hub. The end of the tape is manually pulled from the reel, threaded through mechanical guides and over a tape head assembly, and attached by friction to the hub of the second, initially empty takeup reel. Reel-to-reel systems use tape that is 1⁄4, 1⁄2, 1, or 2 inches wide, which normally moves at 3+3⁄4, 7+1⁄2, 15 or 30 inches per second. Domestic consumer machines almost always used 1⁄4 inch (6.35 mm) or narrower tape and many offered slower speeds such as 1+7⁄8 inches per second (4.762 cm/s). All standard tape speeds are derived as a binary submultiple of 30 inches per second.

The Digital Audio Stationary Head or DASH standard is a reel-to-reel, digital audio tape format introduced by Sony in early 1982 for high-quality multitrack studio recording and mastering, as an alternative to analog recording methods. DASH is capable of recording two channels of audio on a quarter-inch tape, and 24 or 48 tracks on 1⁄2-inch-wide (13 mm) tape on open reels of up to 14 inches. The data is recorded on the tape linearly, with a stationary recording head, as opposed to the DAT format, where data is recorded helically with a rotating head, in the same manner as a VCR. The audio data is encoded as linear PCM and boasts strong cyclic redundancy check (CRC) error correction, allowing the tape to be physically edited with a razor blade as analog tape would, e.g. by cutting and splicing, and played back with no loss of signal. In a two-track DASH recorder, the digital data is recorded onto the tape across nine data tracks: eight for the digital audio data and one for the CRC data; there is also provision for two linear analog cue tracks and one additional linear analog track dedicated to recording time code.

Sync sound refers to sound recorded at the time of the filming of movies. It has been widely used in movies since the birth of sound movies.

<span class="mw-page-title-main">Flatbed editor</span> Film editing machine

A flatbed editor is a type of machine used to edit film for a motion picture.

Since the widespread adoption of reel-to-reel audio tape recording in the 1950s, audio tapes and tape cassettes have been available in many formats. This article describes the length, tape thickness and playing times of some of the most common ones.

<span class="mw-page-title-main">Motion picture film scanner</span> Device that digitises film stock

A motion picture film scanner is a device used in digital filmmaking to scan original film for storage as high-resolution digital intermediate files.

Cinema Digital Sound (CDS) was a multi-channel surround sound format used for theatrical films in the early 1990s. The system was developed by Eastman Kodak and Optical Radiation Corporation. CDS was quickly superseded by Digital Theatre Systems (DTS) and Dolby Digital formats.

Double-system recording is a form of sound recording used in motion picture production whereby the sound for a scene is recorded on a tape machine that is separate from the camera or picture-recording apparatus.

<span class="mw-page-title-main">History of multitrack recording</span>

Multitrack recording of sound is the process in which sound and other electro-acoustic signals are captured on a recording medium such as magnetic tape, which is divided into two or more audio tracks that run parallel with each other. Because they are carried on the same medium, the tracks stay in perfect synchronization, while allowing multiple sound sources to be recorded at different times.

<span class="mw-page-title-main">Film chain</span>

A film chain or film island is a television – professional video camera with one or more projectors aligned into the photographic lens of the camera. With two or more projectors a system of front-surface mirrors that can pop-up are used in a multiplexer. These mirrors switch different projectors into the camera lens. The camera could be fed live to air for broadcasting through a vision mixer or recorded to a VTR for post-production or later broadcast. In most TV use this has been replaced by a telecine.

<span class="mw-page-title-main">Spirit DataCine</span> Motion picture film scanner

Spirit DataCine is a telecine and a motion picture film scanner. This device is able to transfer 16mm and 35mm motion picture film to NTSC or PAL television standards or one of many High-definition television standards. With the data transfer option a Spirit DataCine can output DPX data files. The image pick up device is a solid state charge-coupled device. This eliminated the need for glass vacuum tube CRTs used on older telecines. The units can transfer negative film, primetime, intermediate film and print film, stock. One option is a Super 8 gate for the transfer of Super 8 mm film. With a sound pick up option, optical 16mm and 35mm sound can be reproduced, also 16mm magnetic strip sound. The unit can operate stand alone or be controlled by a scene by scene color corrector. Ken Burns created The Civil War, a short documentary film included in the DVD release, on how he used the Spirit DataCine to transfer and remaster this film. The operator of the unit is called a Colorist or Colorist Assistant. The Spirit DataCine has become the standard for high-end real-time film transfer and scanning. Over 370 units are used in post-production facilities around the world. Most current film productions are transferred on Spirit DataCines for Television, Digital television, Cable television, Satellite television, Direct-to-video, DVD, Blu-ray Disc, pay-per-view, In-flight entertainment, Stock footage, Dailies, Film preservation, digital intermediate and digital cinema. The Spirit DataCine is made by DFT Digital Film Technology GmbH in Darmstadt, Germany.

The pallophotophone was a photographic sound recording and playback system developed by General Electric researcher Charles A. Hoxie circa 1922. The RCA Photophone sound-on-film system for motion pictures was later derived from it.

Sondor is a manufacturer of Audio Video equipment located in Zollikon, Switzerland until 2017. Sondor was founded in 1952 by Willy Hungerbuehler. Sondor started as a manufacturer of 16 mm film and 35mm film magnetic film equipment. They are noted as inventing the standard for bi-phase interlocking pulse signals to sync sound to film. Sondor added a film transport telecine to it line of film sound equipment. Sondor products are found in many in post-production studios for record and playback and in movie theater for sound playback. playback.

<span class="mw-page-title-main">Music technology (electric)</span> Musical instruments and recording devices that use electrical circuits

Electric music technology refers to musical instruments and recording devices that use electrical circuits, which are often combined with mechanical technologies. Examples of electric musical instruments include the electro-mechanical electric piano, the electric guitar, the electro-mechanical Hammond organ and the electric bass. All of these electric instruments do not produce a sound that is audible by the performer or audience in a performance setting unless they are connected to instrument amplifiers and loudspeaker cabinets, which made them sound loud enough for performers and the audience to hear. Amplifiers and loudspeakers are separate from the instrument in the case of the electric guitar, electric bass and some electric organs and most electric pianos. Some electric organs and electric pianos include the amplifier and speaker cabinet within the main housing for the instrument.

<span class="mw-page-title-main">Sanyo Micro Pack 35</span>

The Sanyo Micro Pack 35 was a portable magnetic audio tape recording device, developed by Sanyo in 1964, that employed a special tape cartridge format with tape reels atop each other.

References

  1. ↑ Audio post production for television and film an introduction to technology, By Hilary Wyatt, Tim Amyes, page 73
  2. ↑ Georgia State University, How record heads work.
  3. ↑ thefreedictionary.com sepmag
  4. ↑ The primary goal is to achieve perfect timing of the audio track in relation to the visual footage. This can be achieved in two ways: Traditionally by recording a pilot track in an area of the tape that serves as a "clock" upon playback. This can be 60 Hz (in the US) or 50 Hz elsewhere, where there is a power line frequency of 50 Hz. In the studio, the playback of the original tape "pilotone" is compared to the power line frequency, and servo locks the playback machine to that power line frequency, while the Mag Film recorder's motor runs synchronously, transporting the 16 mm or 35 mm magnetic film being recorded. The newer methods take advantage of the timing of the microprocessor clock accuracy, and rely on playback timing that is nearly absolute, for the length of a typical "take" anyway. Most 16 mm film loads are limited to 11 min, as the magazines typically hold 400 ft of film. This second method requires that the camera's drive system runs at a nearly absolute speed. Typically, this is achieved using a crystal frequency standard, which runs the camera motor. The motor drives sprocketed film, so there is no error from slippage, as found in the recording tape process. abctvgorehill.com.au mag unit at ABC in the 1950s, to play the sound locked to a film chain
  5. ↑ soundonsound.com A Practical Guide To Working With Pictures, Part 3,Tips & Tricks, Published August 2000.
  6. ↑ digitalpostservices.com, Glossary of Film Terms
  7. ↑ The Greater London Industrial Archaeology Society Syncwriter 1983–1986, Film and Sepmag
  8. ↑ n70mm.com, Todd-AO studios, use of room full of Magnatech units in post production.
  9. ↑ History of Telecine at the BBC, 1994
  10. ↑ The Editors Guild Magazine, "Math of Movies", Vol. 24, No. 1 – January/February 2003.
  11. ↑ Sound recording, the life story of a technology, by David L. Morton, Jr.
  12. ↑
  13. ↑ College of Communication – The University of Texas at Austin How to use a Magnatech
  14. 1 2 Stan Ginsel, Video Producer Classic Movie Making – What’s a Dubber and Mag Stock?
  15. ↑ The Editors Guild Magazine Vol. 25, No.1 page 126- January/February 2004, by Gregg Rudloff, Film Mixing.
  16. ↑ Presto Page 8, PRESTO – Preservation Technologies for European Broadcast Archives, IST-1999-20013, 3/05/2001
  17. ↑ http://tech.ebu.ch/ Preservation and Reuse of Film material for television May 2001, page 5
  18. ↑ Audio Engineering Society AES E-Library Magnetic Film Transport Based on the SEPMAG Method: Basis and Developmental Program from the First Unit up to the Present Time
  19. ↑ Audio Engineering Society Audio Technology in Berlin to 1943: Magnetic Sound Activities – Heinz H. K. Thiele
  20. ↑ magna-tech.com M.T.E history
  21. ↑ National Association of Broadcasters Engineering Handbook, by Graham A. Jones, Edmund A. Williams, David H. Layer, Thomas G. Osenkowsky, pages 456–459.
  22. ↑ magna-tech.com SERIES 600
  23. ↑ youtube.com Magna Tech 10036-3 Film Sound Follower Recorder Player.
  24. ↑ Magna Tech 10036-3 Film Sound Follower Recorder Player Archived 2012-03-23 at the Wayback Machine
  25. ↑
  26. ↑ http://magna-tech.com Magnetic Film Recorders
  27. ↑ sondor.ch OMA E
  28. ↑ sondor.ch BASIC
  29. ↑ sondor.ch SOUNDHOUSE
  30. ↑ Swiss National Sound Archives
  31. ↑ sondor.ch ALTRA
  32. ↑ Summertone on Sondor
  33. ↑ SMPTE MTM add, page 5
  34. ↑ Ranger Tone by MTM
  35. ↑ journal.smpte.org MTM add, page 517
  36. ↑ brunswickfilms.com Brunswick gets a Rank Cintel Ferrit, Sep. 18, 2009
  37. ↑ damsmart.com.au MWA-Nova history
  38. ↑ MWA Nova GmbH
  39. ↑ flashscan8.us Model MB51
  40. ↑ www.mwa-nova.com/ MWA Albrecht GmbH, Model MB51
  41. ↑ film-tech.com Magnatech
  42. ↑ SMPTE RCA page 2, and Magna Tech page 19
  43. ↑ openreel.net TEAC 35 mm mag film sound recorder, 1968
  44. ↑
  45. ↑ http://www.steenbeck.com
  46. ↑ steenbeck.com Steenbeck ST3514 with sepmag option
  47. ↑ radiomuseum.org Kinevox history
  48. ↑ radiomuseum.org Kinevox Synchronous Magnetic Film Recorder
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.