Crystal oscillator frequencies

Last updated

Crystal oscillators can be manufactured for oscillation over a wide range of frequencies, from a few kilohertz up to several hundred megahertz. Many applications call for a crystal oscillator frequency conveniently related to some other desired frequency, so hundreds of standard crystal frequencies are made in large quantities and stocked by electronics distributors. Using frequency dividers, frequency multipliers and phase locked loop circuits, it is practical to derive a wide range of frequencies from one reference frequency.

The UART column shows the highest common baud rate (under 1,000,000), assuming a clock pre-divider of 16 is resolved to an exact integer baud rate. Though some UART variations have fractional dividers, those concepts are ignored to simplify this table.

Frequency (MHz)comm UART A/V RTC Notes and Primary uses
0.032000Yes check.svgReal-time clock, watches; allows binary division to 1 kHz signal (25×1 kHz).
0.032768Yes check.svg 215 allows binary division to 1 Hz. Real-time clock, quartz watches and clocks; common low-speed for microcontrollers. Very common. Available as TCXO. [1]
0.038000Used with FM stereo encoder chip BA1404 and similar.
0.065536Yes check.svg 216 allows binary division to 1 Hz and 32.768 kHz. Real-time clock.
0.077500Yes check.svgReal-time clock, quartz watches and clocks; also the DCF77 frequency
0.100000Yes check.svg 105 allows decade division to 1 Hz and 1 kHz. Real-time clock, quartz watches and clocks, DMM dual slope ADCs (suppresses 50 Hz noise)
0.120000Yes check.svg DMM dual slope ADCs (suppresses 60 Hz noise)
0.131072Yes check.svg 217 allows binary division to 1 Hz and 32.768 kHz. Found in Fluke 17/19 DMM's[ citation needed ]
0.262144Yes check.svg 218 allows binary division to 1 Hz and 32.768 kHz. Found in Bulova Precisionist high-frequency quartz watches. [2]
0.383000Ceramic resonator, in e.g. Polaroid Sonia Transducer for distance [3]
0.429000radio (filter) Ceramic resonator used in some intermediate frequency filters. Common in oscillators of 36 kHz infrared remote controls (divided by 12)
0.455000radio (filter) Ceramic resonator used in FM broadcasting intermediate frequency filters. Common in oscillators of 38 kHz infrared remote controls (divided by 12), cheaper than crystal but less stable frequency
0.46080028800radio Ceramic resonator used in HART. UART clock allows integer division to common baud rates up to 28,800(×16×1) or 57,600(×8×1).
0.480000radio (filter) Ceramic resonator used in some intermediate frequency filters and low-cost oscillators. Also used in DTMF generator oscillators.
0.500000radio (filter) Ceramic resonator used in some intermediate frequency filters and low-cost oscillators
0.524288Yes check.svg 219 allows binary division to 1 Hz and 32.768 kHz.
1.000 106 allows decade division to 1 Hz and 1 kHz. Reference frequency. Common standard frequency. Harmonics fall on integer MHz frequencies.
1.048576Yes check.svg 220 allows binary division to 1 Hz and 32.768 kHz. Real-time clock.
1.0081200UART clock allows integer division to common baud rates up to 1,200(×8×105). Used in some 1200 baud modems.
1.544 DS1 Bit clock for DS1 systems (±32 ppm, ANSI T1.102).
1.8432115200UART clock allows integer division to common baud rates up to 115,200(×16×1) or 230,400(×8×1). Since older UARTs used this frequency to derive common baud rates up to 115,200, then multiples of this frequency are able to do the same, such as 3.6864 / 5.5296 / 7.3728 / 9.216 / 11.0592 / 12.9024 / 14.7456 / 16.5888 / 18.432 / 20.2752 / 22.1184 / 23.9616 / 25.8048 / 27.648 / 29.4912 / 31.3344 / 33.1776 / 35.0208 / 36.864 / ..., and is why these MHz frequencies are commonly used.
2.048 E1 Allows binary division to 1 kHz (211×1 kHz). Bit clock for E1 systems (±50 ppm, ITU G3703).
2.097152Yes check.svg 221 allows binary division to 1 Hz and 32.768 kHz; real-time clock; also for DDS generators with 1 Hz step
2.457638400UART clock allows integer division to common baud rates up to 38,400(×16×4) or 76,800(×16×2).
2.500 Ethernet Ethernet clock for 10 Mbit/s
2.560Allows binary division to 10 kHz (28×10 kHz)
2.82242400audioUsed in CD-DA systems and CD-ROM drives; allows binary division to 44.1 kHz (64×44.1 kHz), 22.05 kHz, and 11.025 kHz. DSD64 bitrate. Frequencies also used are 5.6448 MHz, 11.2896 MHz, 16.9344 MHz, 22.5972 MHz, 33.8688 MHz and 45.1584 MHz.
2.8807200UART clock allows integer division to common baud rates up to 7,200(×16×25) or 14,400(×8×25). Audio clock allows integer division for 48 / 96 / 192 ksps.
3.072128000audioYes check.svgAllows binary division to 3 kHz (210×3 kHz); can be used to generate 60 Hz signals (51200×60 Hz). Used in audio systems, for 48 kHz (64×), 96 kHz (32×), 192 kHz (16×), 384 kHz (8×)
3.088 DS1 2×1.544, the bit clock for DS1 systems (±32 ppm, ANSI T1.102). Available as TCXO and OCXO.
3.2768Yes check.svgAllows binary division to 100 Hz (32,768×100 Hz, or 215×100 Hz) and to 50 Hz, used in e.g. wattmeters and DC-AC converters
3.560 Amateur Radio A common QRP frequency (80-meter band), also called 3560 kHz. Other less common crystals for the same band are 3.535, 3.550 (SKKC), 3.579 (digital modes) MHz. See also 7.025 MHz.
3.575611 PAL PAL M color subcarrier
3.579545 NTSC NTSC M color subcarrier; see colorburst. More specifically, 315/88 = 3.57954 MHz. Because these are very common and inexpensive they are used in many other applications, for example DTMF generators
3.582056 PAL PAL-N color subcarrier
3.595295 NTSC NTSC M color subcarrier, plus horizontal scan rate (15,750). Used for a rainbow color test, produces color through the entire 360 degrees of phase shift. Unusual. [4]
3.640radio8×455 kHz AM broadcast band intermediate frequency; also often used in infrared remote controls as the clock source
3.6864 W-CDMA 230400UART clock allows integer division to common baud rates up to 230,400(×16×1) or 460,800(×8×1). Also used in W-CDMA systems.
3.93216Yes check.svgAllows binary division to 60 Hz (65536×60 Hz, 216×60 Hz), used e.g. in wattmeters, DC-AC converters and NTSC vertical sync generators
4.000Common general low-power microcontroller frequency. Common as cheap ceramic resonators where frequency stability is of less concern than cost.
4.0327200UART clock allows integer division to common baud rates up to 7,200(×16×35) or 14,400(×8×35), used for some 1200, 2400, and 4800 baud modems.
4.096 ISDN 256000Yes check.svgAllows binary division to 1 kHz (212×1 kHz). Used in ISDN systems.
4.190 Ceramic resonator used in some intermediate frequency filters and low-cost oscillators, common
4.194304Yes check.svg 222 allows binary division to 1 Hz and 32.768 kHz. Real-time clock. For DDS generators with 1 Hz step. Used in the original Game Boy.
4.3201800Yes check.svgUsed for measuring 1pps deviations in 1/50th seconds per day (24h × 60m × 60s × 50). UART clock allows integer division to common baud rates up to 1,800(×16×150) or 7,200(×8×75). Audio clock allows integer division for 48 / 96 ksps.
4.3218audioUsed in CD-DA systems and CD-ROM drives; allows integer division to 44.1 kHz (98×44.1 kHz), 22.05 kHz, and 11.025 kHz. Frequencies also used are 8.6436 MHz and 17.2872 MHz.
4.332 RDS 3648× the RDS signal bit rate of 1187.5 bit/s. While the frequency of 4.332 MHz is the most commonly used crystal resonator, its multiples (2×4.332 MHz = 8.664 MHz or 4×4.332 MHz = 17.328 MHz) have been used also.
4.43361875 PAL/NTSC PAL B/D/G/H/I and NTSC M4.43 color subcarrier. Also used in Compact Disc players and recorders where the crystal frequency is slightly pulled to 4.41 MHz and then divided by 100 to give the 44.1 kHz sampling frequency. See also twice the frequency, 8.867238 MHz.
4.60857600audioYes check.svgUART clock allows integer division to common baud rates up to 57,600(×16×5) or 115,200(×8×5). Audio clock allows integer division for 48 / 96 / 192 ksps. Allows integer division to 1024 kHz and binary division to lower frequencies that are whole multiples of 1 Hz. Common microcontroller clock frequency. Frequency of the Master Timing Unit (MTU) OCXO of the Space Shuttle. [5] [6]
4.7547radio (ISM)Oscillator for 315 MHz FSK/ASK superheterodyne receivers with 10.7 MHz intermediate frequency (common Chinese ISM band use for small RF remote controls), multiplied 64× (4.7547×64+10.7=315) [7]
4.897Reference clock for some 315 MHz transmitters and receivers, e.g. garage door openers. (Alternative frequencies for the same chipsets: 6.0630 MHz for 390 MHz, 6.4983 MHz for 418.00 MHz, 6.7458 MHz for 433.92 MHz; swapping them can swap the band.)
4.9152 CDMA 38400Used in CDMA systems; divided to 1.2288 MHz baseband frequency as specified by J-STD-008. UART clock allows integer division to common baud rates up to 38,400(×16×8) or 76,800(×8×4).
5.000Common standard frequency. Commonly available as TCXO and OCXO.
5.034965 NTSC Integer multiple of the 59.94 Hz (84000×) vertical refresh and the 15.734 kHz (320×) horizontal scan rates
5.068857600UART clock allows integer division to common baud rates up to 14,400(×16×22) or 57,600(×8×11).
5.120Yes check.svgAllows binary division to 10 kHz (29×10 kHz)
5.185radioUsed in radio transceivers, clock for some microcontrollers
5.5296115200UART clock allows integer division to common baud rates up to 115,200(×16×3) or 230,400(×8×3).
5.644814400audioUsed in CD-DA systems and CD-ROM drives; allows binary division to 44.1 kHz (128×44.1 kHz), 22.05 kHz, and 11.025 kHz. DSD128 bitrate (2× 2.8224 MHz). Frequencies also used (multiplies of 5.6448) are 11.2896 MHz, 16.9344 MHz, 22.5972 MHz, 33.8688 MHz and 45.1584 MHz.
6.000 USB Common in low-speed (1.5 Mbit/s) USB devices such as computer keyboards.
6.063Reference clock for some 390 MHz transmitters and receivers, e.g. garage door openers. (Alternative frequencies for the same chipsets: 4.8970 MHz for 315.00 MHz, 6.4983 MHz for 418.00 MHz, 6.7458 MHz for 433.92 MHz; swapping them can swap the band.)
6.14438400audioYes check.svgDigital audio systems - DAT, MiniDisc, sound cards; 128×48 kHz (27×48 kHz). UART clock allows integer division to common baud rates up to 38,400(×16×10) or 256,000(×8×3).
6.176 DS1 4×1.544, the bit clock for DS1 systems (±32 ppm, ANSI T1.102). Available as TCXO and OCXO.
6.400Binary multiple of 100 kHz (64×100 kHz), 50 kHz, 25 kHz, 12.5 kHz. Half of the common standard 12.8 MHz.
6.451211520021×307.2 kHz; UART clock allows integer division to common baud rates up to 57,600(×16×7) or 115,200(×8×7). See also 3×, 19.3536 MHz.
6.480 SONET 28800Used to generate (×8) 51.84 MHz, the SONET STS-1 frequency (with accuracy of 20 =ppm). [8]
6.4983Reference clock for some 418 MHz transmitters and receivers, e.g. TV remote extenders or wireless sensors. (Alternative frequencies for the same chipsets: 4.8970 MHz for 315.00 MHz, 6.0630 MHz for 390 MHz, 6.7458 MHz for 433.92 MHz; swapping them can swap the band.)
6.5536Allows binary division to 100 Hz (65,536×100 Hz, or 216×100 Hz); used also in red boxes
6.6128radio (ISM)Oscillator for 433.92 MHz FSK/ASK superheterodyne receivers with 10.7 MHz intermediate frequency (common ISM band use for small RF remote controls), multiplied 64× (6.6128×64+10.7=433.92) [7]
6.7458Reference clock for some 433.92 MHz ISM band transmitters and receivers, e.g. wireless sensors. (Alternative frequencies for the same chipsets: 4.8970 MHz for 315.00 MHz, 6.0630 MHz for 390 MHz, 6.4983 MHz for 418.00 MHz; swapping them can swap the band.) Available as TCXO.
6.750 SDTV SDTV NTSC 4:3 pixel clock (352×480i@29.97)
7.023 Amateur Radio CW Paradise in China. A common QRP frequency (40-meter band). [9] Used with Pixie QRPP transceiver. Other less common frequencies are 7.030 (QRP, digital), 7.035, 7.040, 7.045, 7.048, 7.050, 7.055 (SKKC), 7.060, 7.070 (digital), 7.110 (QRP), 7.114, 7.122 MHz.
7.15909 NTSC NTSC M color subcarrier (2×3.579545 MHz)
7.200DARC1800UART clock allows integer division to common baud rates up to 1,800(×16×250) or 7,200(×8×125). Audio clock allows integer division for 48 / 96 ksps. Half of the more common 14.4 MHz. Reference clock for DARC.
7.3728460800UART clock allows integer division to common baud rates up to 460,800(×16×1) or 921,600(×8×1).
7.600RadioPLL clock for pilot tone (400×19 kHz) in FM stereo.
8.000 CAN Used in CAN bus systems and with many small microcontroller systems. Common general microcontroller frequency (i.e. STM32 Nucleo boards, 3.3V AVR-based Arduino boards). Common as cheap ceramic resonators where frequency stability is less concern than cost.
8.184 GPS Half the 16.368 MHz frequency; same use in different chipsets. 8 times the 1.023 MHz C/A GPS signal chipping rate. Multiplied by 192.5 to get the 1575.42 MHz L1 frequency and multiplied by 150 to get the 1227.60 MHz L2 frequency.
8.192 ISDN 256000audioYes check.svgAllows binary division to 1 kHz (213×1 kHz). Used in ISDN systems. Used in OKI Speech Processor. Common audio clock, 256×32 kHz (see also 11.2896, 12.288, 16.384, 18.4323, 22.5792, 24.576 MHz). Typical TDM/PCM audio interface clock, 1/6 of 49.152 MHz. [10]
8.388608Yes check.svg 223 allows binary division to 1 Hz and 32.768 kHz. Real-time clock; also for DDS generators with 1 Hz step. Used in the Game Boy Color.
8.46721800audioUsed in CD-DA systems and CD-ROM drives; allows integer division to 44.1 kHz (192×44.1 kHz), 22.05 kHz, and 11.025 kHz. UART clock allows integer division to common baud rates up to 1,800(×16×294) or 7,200(×8×147). Frequencies also used are 11.2896 MHz, 16.9344 MHz, 22.5972 MHz, 33.8688 MHz and 45.1584 MHz.
8.6436audioUsed in CD-DA systems and CD-ROM drives; allows integer division to 44.1 kHz (196×44.1 kHz), 22.05 kHz, and 11.025 kHz. Frequencies also used are 4.3218 MHz and 17.2872 MHz.
8.664 RDS The RDS signal bit rate is at 1.1875 kbit/s. While the frequency of 4.332 MHz is the most commonly used crystal resonator, its multiples (2×4.332 MHz = 8.664 MHz or 4×4.332 MHz = 17.328 MHz) have been used also.
8.86724
8.867238		 PAL PAL B/G/H color subcarrier (2×4.433618 MHz)
9.000 SDTV SDTV PAL/NTSC 16:9 pixel clock (480×480i@29.97, 480×576i@25)
9.216576000audioYes check.svgUART clock allows integer division to common baud rates up to 115,200(×16×5) or 576,000(×16×1). Audio clock allows integer division for 48 / 96 / 192 ksps. Allows integer division to 1024 kHz and binary division to lower frequencies that are whole multiples of 1 Hz. Master clock for some Japanese variants of DOCSIS.
9.29063radio (ISM)Oscillator for 308 MHz FSK/ASK superheterodyne receivers with 10.7 MHz intermediate frequency (less common band used for small RF remote controls), multiplied 32× (9.29063*32+10.7=308) [11]
9.50939radio (ISM)Oscillator for 315 MHz FSK/ASK superheterodyne receivers with 10.7 MHz intermediate frequency (common Chinese ISM band used for small RF remote controls), multiplied 32× (9.50939*32+10.7=315) [11]
9.54545 NTSC 2/3 of the 14.31818 MHz NTSC clock, 1/3 of the 28.636 MHz clock; common clock for microcontrollers and older processors. Exactly 210/22  MHz.
9.6004800UART clock allows integer division to common baud rates up to 4,800(×16×125) or 9,600(×8×125). Available as TCXO and OCXO. Used in 19.2 and 48 MHz PLL generators. Can be used as seed clock for 48 and 60 GHz PLL oscillators and in frequency synthesizers for mobile radio as the common channel spacings can be easily derived. [12]
9.8304 CDMA 38400Used in CDMA systems (2×4.9152 MHz); divided to 1.2288 MHz baseband frequency. UART clock allows integer division to common baud rates up to 38,400(×16×16) or 76,800(×8×16).
9.84375radio (ISM)Used as clock in some 315 MHz remote fob and IoT transmitters (multiplied by 32); 13.560 MHz used for 433.92 MHz
9.900 SDTV SDTV NTSC pixel clock (528×480i@29.97)
10.000 107 allows decade division to 1 Hz and 1 kHz. Common standard frequency. Commonly available as TCXO, the most common OCXO and GPS-disciplined oscillator available. Common stratum 3 Network Time Protocol frequency. [13] Common general microcontroller frequency. Common as cheap ceramic resonators where frequency stability is less concern than cost.
10.106 Amateur Radio A common QRP frequency (30-meter band). Other crystals are 10.116 (QRP), 10.118, 10.120 (SKKC), 10.140 (digital) MHz. See also 7.025 MHz.
10.125 SDTV SDTV PAL/NTSC pixel clock (544×480i@29.97, 544×576i@25)
10.230 GPS Found in some GPS receivers. Equals the P(Y) GPS signal chipping rate. 10 times the 1.023 MHz C/A GPS signal chipping rate. Multiplied by 154 to get the 1575.42 MHz L1 frequency and multiplied by 120 to get the 1227.60 MHz L2 frequency. Available as OCXO and TCXO.
10.240 DOCSIS/TD-SCDMA Yes check.svgAllows binary division to 10 kHz (210×10 kHz). Common as a clock in CB radio PLL frequency synthesizers to generate the 5 kHz or 10 kHz reference signal. [14] Used in frequency synthesizers in some cordless phones and in many radio frequency transceivers. Master clock for DOCSIS/EuroDOCSIS. Used in cable modem termination systems. Used to derive symbol and chip rate in conventional TD-SCDMA systems. Available as OCXO and TCXO.
10.245 FM radio Used in radio receivers; mixes with 10.7 MHz intermediate frequency (IF) yielding 455 kHz signal, a common second IF for FM radio [15]
10.368 DECT 14400Reference clock for DECT phones. Available as TCXO. Other frequencies are 13.824 and 20.736 MHz. UART clock allows integer division to common baud rates up to 14,400(×16×45) or 28,800(×8×45)
10.416667 Ethernet Multiplied by 12 to 125 MHz Gigabit Ethernet GMII GTXCLK clock, FDDI clock
10.70 FM radio radio (filter)Most common crystal or ceramic resonator for first intermediate frequency filter in FM radio; common in other applications due to ubiquity and low cost, filter bandwidth varies (e.g. ±250/230/180/150/110 kHz to both sides from the 10.7 MHz frequency)
11.0592230400UART clock allows integer division to common baud rates up to 230,400(×16×3) or 460,800(×8×3); common clock for Intel 8051 microprocessors [16]
11.289614400audioUsed in CD-DA systems and CD-ROM drives; allows binary division to 44.1 kHz (256×44.1 kHz), 22.05 kHz, and 11.025 kHz. DSD256 bitrate (4x2.8224 MHz). Frequencies also used are 16.9344 MHz, 22.5972 MHz, 33.8688 MHz and 45.1584 MHz. UART clock allows integer division to common baud rates up to 14,400(×16×49) and 28,800(×8×49).
11.454544 teletext Used in some teletext circuits; 2×5.727272 MHz (clock frequency of NTSC M teletext; PAL B uses 6.9375 MHz, SECAM uses 6.203125 MHz, PAL G uses 6.2031 MHz, and PAL I uses 4.4375 MHz clock)
11.52028800UART clock allows integer division to common baud rates up to 28,800(×16×25) or 57,600(×8×25).
12.000 USB/CAN Used in USB 1.0 and 2.0 systems (with accuracy of 500 ppm) as the reference clock for the full-speed PHY rate of 12 Mbit/s, or multiplied up using a PLL to clock high speed PHYs at 480 Mbit/s; common clock for Intel 8051 microprocessors; [16] also used in CAN bus systems. Common general microcontroller frequency. Common as cheap ceramic resonators where frequency stability is less concern than cost.
12.272727 SDTV Clock rate for exactly square pixels in interleaved 4:3 640×480i@29.97 NTSC video ( MHz). In practice the more commonly available 12.288 MHz frequency is close enough for most applications.
12.28876800audioYes check.svgDigital audio systems - DAT, MiniDisc, sound cards; 256×48 kHz (28×48 kHz). UART clock allows integer division to common baud rates up to 76,800(×16×20) or 256,000(×16×3)
12.352 DS1 8x1.544, the bit clock for DS1 systems (±32 ppm, ANSI T1.102). Available as TCXO and OCXO.
12.40625 teletext Used in some teletext circuits; 2×6.203125 MHz (clock frequency of SECAM teletext; PAL B uses 6.9375 MHz, NTSC M uses 5.727272 MHz, PAL G uses 6.2031 MHz, and PAL I uses 4.4375 MHz clock)
12.72813radio (ISM)Oscillator for 418 MHz FSK/ASK superheterodyne receivers with 10.7 MHz intermediate frequency (less common band used for small RF remote controls), multiplied 32x (12.72813x32+10.7=418) [11]
12.800Common standard frequency, common reference clock; binary multiple of 100 kHz (128×100 kHz), 50 kHz, 25 kHz, 12.5 kHz. Commonly available as TCXO and OCXO. Common stratum 3 frequency. [13]
12.9024115200UART clock allows integer division to common baud rates up to 115,200(×16×7) or 230,400(×8×7)
12.9601800UART clock allows integer division to common baud rates up to 1,800(×16×450) or 7,200(×8×225)
13.000 GSM/UMTS Commonly used as a reference clock for GSM and UMTS handsets. (13 MHz is exactly 48 times the GSM bit rate). Commonly available as TCXO and OCXO.
13.22563radio (ISM)Oscillator for 433.92 MHz FSK/ASK superheterodyne receivers with 10.7 MHz intermediate frequency (less common band used for small RF remote controls), multiplied 32x (13.22563*32+10.7=433.12) [11]
13.500 SDTV Master clock for PAL/NTSC DVD players, Digital TV receivers, etc. (13.5 MHz is an exact multiple of the PAL and NTSC line frequencies); pixel clock for 4:3 SDTV PAL/NTSC (720×480i@29.97, 720×576i@25, 352×480p@59.94). CCIR-601 PAL samplerate (864×625 resolution incl. blanking, or 720×576 visible), CCIR-601 NTSC samplerate (858×525 incl. blanking, 720×480 visible)
13.516876800UART clock allows integer division to common baud rates up to 76,800(×16×11)
13.560 RFID Common contactless smartcard frequency (ISO/IEC 14443). Also used as clock in some 433.92 MHz remote fob transmitters (multiplied by 32); 9.84375 MHz used for 315 MHz
13.824 DECT 57600Reference clock for DECT phones. Available as TCXO. UART clock allows integer division to common baud rates up to 57,600(×16×15) or 576,000(×8×3). Other frequencies are 10.368 and 20.736 MHz.
13.875 teletext Used in some teletext circuits; 2×6.9375 MHz (clock frequency of PAL B teletext; SECAM uses 6.203125 MHz, NTSC M uses 5.727272 MHz, PAL G uses 6.2031 MHz, and PAL I uses 4.4375 MHz clock)
14.048 Amateur Radio A common amateur radio frequency (20-meter band). Other crystals are 14.050 (SKCC), 14.060 (QRP), 14.070 (digital) MHz. See also 7.025 MHz.
14.1121800audioDigital audio systems - 294×48 kHz, 320×44.1 kHz. UART clock allows integer division to common baud rates up to 1,800(×16×490) or 7,2000(×8×245). Available as TCXO.
14.250 FM radio PAL used as sampling frequency for ADCs for digitizing the 10.7 MHz intermediate frequency in software-defined radio implementations of AM/FM radio receivers. [17] Pixel clock of some PAL CCD cameras (raw image resolution of 912×625). [18] Used in PAL version in some early Apple computers, e.g. Apple II Europlus.
14.318182 NTSC NTSC M color subcarrier (4×3.579545 MHz). Common seed clock for modern PC motherboard clock generator chips, clock for ISA bus, also common on CGA and VGA cards and in some 8-bit computers. Exactly 315/22 MHz. 4f(sc) sampling for NTSC or 525/60 (raw image size 910×525, visible 768×475), SMPTE 244M standard.
14.350 NTSC Pixel clock of some NTSC CCD cameras. [18]
14.400 PDC 7200UART clock allows integer division to common baud rates up to 7,200(×16×125) or 14,400(×8×125). Also a reference clock for PDC clock. Reference clock of some consumer GPS receivers. [19]
14.7456921600UART clock allows integer division to common baud rates up to 921,600(×16×1); common clock for small microcontrollers
14.750 SDTV Clock rate for exactly square pixels in SDTV PAL 4:3 interleaved 768×576i@25 video ( MHz). In practice the more commonly available 14.7456 MHz frequency is close enough for most applications.
14.850Used in some transceivers and cellular radios as a reference clock for frequency synthesis. Available as TCXO.
15.000Used as clock in ZX8301 computer (divided to 7.5 MHz). Frequency used in photoacoustic imaging. Sometimes available as OCXO. Used in dual-frequency 315/390 MHz RF key fobs (multiplied by 21 or 26). [20]
15.360 3G 38400Yes check.svgUART clock allows integer division to common baud rates up to 38,400(×16×25) or 128,000(×8×15). Also used as a 3G reference clock. [21] Used as reference clock in some Bluetooth systems.
15.600Used in Kenwood TS-590 transceivers. Audio clock allows integer division for 48 ksps. Available as TCXO.
16.000 CAN HGC Used in CAN bus systems, some USB devices. 2.4 GHz ISM transceivers. Common general microcontroller frequency (i.e. Arduino Uno and Nano boards). Common as cheap ceramic resonators where frequency stability is less concern than cost. Pixel clock for Hercules Graphics Card. Also used for ZigBee, Bluetooth and BLE, WiFi. [22]
16.200 HDTV Sampling clock for MUSE HDTV systems (). Rarely used as reference clock in some Bluetooth systems.
16.257 EGA Pixel clock generator in MGA and EGA video cards (640×350@60 Hz) [23]
16.367600
16.367667
16.368000		 GPS Commonly used for down-conversion and sampling in GPS-receivers. Generates intermediate frequency signal at 4.092 MHz. 16.3676 or 16.367667 MHz are sometimes used instead of 16.368 MHz to avoid perfect lineup between sampling frequency and GPS spreading code. 16.368 MHz is a reference clock of some consumer GPS receivers. [19] 16.368 MHz is 16 times the 1.023 MHz C/A GPS signal chipping rate; multiplied by 96.25 to get the 1575.42 MHz L1 frequency and multiplied by 75 to get the 1227.60 MHz L2 frequency.
16.369 GPS Reference clock for some GPS systems. Available as TCXO. [24]
16.375 SDTV SDTV NTSC 16:9 pixel clock (864×480i@29.97), square pixels (854×480 would be ideal, 864×480 is close enough and a multiple of 16 and 32 for MPEG compression blocks)
16.384256000Yes check.svgAllows binary division to 1 kHz (214×1 kHz). Reference clock of some consumer GPS receivers. [19] Common audio clock, 256×64 kHz, 512×32 kHz (see also 8.192, 11.2896, 12.288, 18.432, 22.5792, 24.576 MHz). Commonly available as TCXO and OCXO.
16.5888115200UART clock allows integer division to common baud rates up to 115,200(×16×9) or 230,400(×8×9).
16.67Core speed of some microcomputers (relatively common in Motorola 68000 family); bus clock; double to 33.33 MHz, quadruple to 66.67 MHz, multiply by 6 to 100 MHz; IOAPIC clock speed, half the PCI bus frequency
16.777216Yes check.svg 224 allows binary division to 1 Hz and 32.768 kHz. Real-time clock; also for DDS generators with 1 Hz step
16.8001200Common standard reference frequency for PLL circuits in radio transmitters and receivers, commonly used for frequency synthesis with adjustment in 2.5, 5 or 6.25 kHz steps (6720×5 kHz, 3360×5 kHz or 2688×5.25 kHz). UART clock allows integer division to common baud rates up to 1,200(×16×875) or 2,400(×8×875). Commonly available as TCXO, VCXO and VCTCXO. Used as reference clock in some Bluetooth systems. Reference clock for some GPS systems. [24]
16.93447200audioUsed in CD-DA systems and CD-ROM drives; allows integer division to 44.1 kHz (384×44.1 kHz), 22.05 kHz, and 11.025 kHz. UART clock allows integer division to common baud rates up to 7,200(×16×147) or 14,400(×8×147). 6x2.8224 MHz (DSD64 bitrate). Frequencies also used are 11.2896 MHz, 22.5972 MHz, 33.8688 MHz and 45.1584 MHz.
17.2032 USB 76800audioPLL conversion by 10/7 to 24.576 MHz and by 21/16 = 22.5792 MHz, which are 256× audio sampling frequencies 48 kHz and 44.1 kHz, respectively. [25] UART clock allows integer division to common baud rates up to 76,800(×16×14).
17.2872audioUsed in CD-DA systems and CD-ROM drives; allows integer division to 44.1 kHz (392×44.1 kHz), 22.05 kHz, and 11.025 kHz. Frequencies also used are 4.3218 MHz and 8.6436 MHz.
17.328 RDS The RDS signal bit rate is at 1.1875 kbit/s. While the frequency of 4.332 MHz is the most commonly used crystal resonator, its multiples (2×4.332 MHz = 8.664 MHz or 4×4.332 MHz = 17.328 MHz) have been used also.
17.664 DSL 9600UART clock allows integer division to common baud rates up to 9,600(×16×115) or 19,200(×8×115); DSL clock: 17.664 MHz (VDSL) ... 8×2.208 MHz (ADSL ADC sampling rate)
17.734475 PAL PAL B/G/H color subcarrier (4×4.433618 MHz); 4f(sc) sampling for PAL or 625/50, gives 1135×625 pixels incl. blankings, or 948×575 visible
18.000 SDTV/HDTV SDTV PAL/NTSC pixel clock for 16:9 (960×480i@29.97, 480×480p@59.94, 960×576i@25, 480×576p@50)
18.096 Amateur Radio A WARC band (17-meter), QRP. Another crystal is 18.086 MHz. See also 7.025 MHz, 10.106 MHz.
18.432576000audioYes check.svgUART clock allows integer division to common baud rates up to 230,400(×16×5) or 576,000(×16×2). Audio clock allows integer division for 48 / 96 / 192 ksps. Integer division for 50 Hz and 60 Hz.
18.75 Ethernet Used to generate 75 MHz (×4) and 150 MHz (×8) clocks.
18.8164800audio/DAT Double the master channel bitrate clock. 9.408 MHz, of Digital Audio Tape systems; 392×48 kHz. The 9.408 MHz clock is divided by 72, 18, 12, and 6 to obtain the pilot, first sync frequency, second sync frequency, and erase frequency. Available as TCXO.
18.9375 PAL Common CCIR/PAL CCTV camera clock frequency (total frame size 1212×625, incl. blankings, @ 25 Hz)
19.069929
19.069930
19.069920
19.069900		 NTSC Common EIA/NTSC CCTV camera clock frequency (total frame size 1212×525, incl. blankings, @29.97 Hz)
19.200 3G 9600 DVB UART clock allows integer division to common baud rates up to 9,600(×16×125) or 19,200(×8×125). Also used as a 3G reference clock, due to being a least common multiple of W-CDMA chip rate 3.84 MHz (5x) and 200 kHz channel raster (96x). [21] Commonly available as TCXO and OCXO. Also used in some DVB receiver chipsets. Reference clock of some consumer GPS receivers. [19] Used as reference clock in some Bluetooth systems. Common stratum 3 frequency. [13] Raspberry Pi 3 (and earlier) main clock crystal (54 MHz for Raspberry Pi 4), can be replaced with more accurate source (TCXO, OCXO, GPS-disciplined) if needed. Used in some DECT, GPS, BLE systems. [22]
19.3536
19.354		1152003×6.4512 MHz; 63×307.2 kHz; UART clock allows integer division to common baud rates up to 57,600(×16×7×3) or 115,200(×8×7×3).
19.440 DS1/T1/E1, Ethernet 1800Used in DS1/T1/E1 systems as a packet clock. Used as reference clock in some Bluetooth systems. Commonly available as TCXO and OCXO. Gigabit Ethernet, used to generate 77.76 MHz (×4), 155.52 MHz (×8), 311.04 MHz (×16), 622.08 MHz (×32).
19.53125 Ethernet Gigabit Ethernet, used to generate 78.125 MHz (×4), 156.25 MHz (×8), 312.5 MHz (×16), 625 MHz (×32); multiplies to 10 GHz MAC-side bitrate, post-serdes; 156.25 MHz = 1/66 of 10.3125 GHz, 1/64 of 10.0 GHz
19.6608 CDMA 76800Used in CDMA systems (4×4.9152); divided to 1.2288 MHz baseband frequency; UART clock allows integer division to common baud rates up to 38,400(×16×32) or 76,800(×16×16).
19.67 SDTV SDTV PAL 16:9 pixel clock (WSVGA 1024×576i@25), square pixels
19.680 CDMA 1200Used in CDMA(IS-95)/CDMA2000 systems; divided to 1.2288 MHz baseband frequency; Used as reference clock in some Bluetooth systems. Commonly available as TCXO.
19.800 CDMA SDTV Used in some CDMA systems. Used as reference clock in some Bluetooth systems. SDTV NTSC pixel clock (528×480p@59.94)
20.000 Ethernet 500000 10 Mbit/s Ethernet. Commonly available as TCXO and OCXO. Common stratum 3 Network Time Protocol frequency. [13] Common general microcontroller frequency. Common as cheap ceramic resonators where frequency stability is less concern than cost. Allows binary division to 10 MHz. Used in some WiFi and Bluetooth systems. [22]
20.141601 Ethernet Gigabit Ethernet. Used to generate 80.566406 MHz (×4) or 161.132812 MHz (×8), 1/128 and 1/64 of 10.3125 GHz of copper Gigabit Ethernet wire bit rate
20.25TV/MAC PAL/NTSC/SDTV Common sampling rate of luma+chroma video components in the Multiplexed Analogue Components standard. Pixel clock for SDTV PAL/NTSC (544×480p@59.94, 544×576p@50).
20.2752115200UART clock allows integer division to common baud rates up to 115,200(×16×11) or 230,400(×8×11).
20.480256000Yes check.svgAllows binary division to 10 kHz (211×10 kHz). Commonly available as TCXO and OCXO.
20.736 DECT 28800Reference clock for DECT phones. Available as TCXO. Other frequencies are 10.368 and 13.824 MHz.
21.050 Amateur Radio A common QRP frequency (15-meter band), SKCC. Other crystal is 21.060 MHz. See also 7.025 MHz.
21.47727 NTSC NTSC M color subcarrier (6×3.579545 MHz). Common seed clock for many older computer systems, e.g. the NTSC-region NES, divided by 12 to CPU clock (1.789773 MHz); see 26.601712 MHz for PAL NES systems. [26]
22.1184460800UART clock allows integer division to common baud rates up to 460,800(×16×3) or 921600(×8×3). Twice the 11.0592 MHz frequency.
22.579228800audioUsed in CD-DA systems and CD-ROM drives; allows binary division to 44.1 kHz (512×44.1 kHz), 22.05 kHz, and 11.025 kHz. DSD512 bitrate (8x2.8224 MHz). Frequencies also used are 11.2896 MHz, 16.9344 MHz, 33.8688 MHz and 45.1584 MHz. UART clock allows integer division to common baud rates up to 28,800(×16×49) or 57,800(×8×49).
22.625Used in Yaesu FT-817, FT-857, and FT-897 transceiver. Available as TCXO.
23.104 GPS Reference clock for some GPS systems. Available as TCXO. [24]
23.9616115200UART clock allows integer division to common baud rates up to 115,200(×16×13) or 230,400(×8×13).
24.000 USB Bluetooth headphones 500000High-speed USB (24 MHz × 20 = 480 Mbit/s); LCD monitor some MCU also Bluetooth headphones. Used in some WiFi, Bluetooth and BLE systems. [22]
24.54 SDTV SDTV NTSC 4:3 pixel clock (640×480p@59.94)
24.5535 GPS Reference clock for some GPS systems. Available as TCXO. [24] Almost 24 times the 1.023 MHz C/A code chipping rate.
24.576FireWire256000audioYes check.svgDigital audio systems - DAT, MiniDisc, AC'97, sound cards; 512×48 kHz (29×48 kHz); also used as bus reference clock in FireWire systems (with accuracy of 100 ppm). 3x8.192 MHz. 49.1520 MHz (2x24.576) also used. Also a crystal for systems handling CCIR-601 SDTV video (here see also 26.8 MHz).
24.704 DS1 16x1.544, the bit clock for DS1 systems (±32 ppm, ANSI T1.102). Available as TCXO and OCXO.
24.906 Amateur Radio A common QRP frequency (12-meter band). See also 7.025 MHz.
25.000 Ethernet Fast Ethernet MII clock (100 Mbit/s/4-bit nibble) (with accuracy of 100 ppm); also multiplied by 5 to 125 MHz Also used on some laptop optical drives Gigabit Ethernet GMII GTXCLK clock, FDDI clock; used as input for 100 MHz PCI Express clock generators [8] Used in some ISM radio systems. [22]
25.175 VGA Common Video Graphics Array pixel clock (i.e., 320/640×200/350/400@70 (320×200@70 Hz, 640×200@70, 320×350@70, 640×350@70, 640×400@70, VGA 640×480@60), all 31.46875 kHz horizontal) [27] [28]
25.8048230400UART clock allows integer division to common baud rates up to 230,400(×16×7) or 460,800(×8×7)
26.000 GSM/UMTS DVB Commonly used as a reference clock for GSM and UMTS/3G handsets. (26 MHz is exactly 96 times the GSM bit rate). Commonly available as TCXO and OCXO. [21] Also used in some DVB receiver chipsets used on portable DVD players. Reference clock of some consumer GPS receivers. [19] Used in Long-CZ J8, Motorola F3 phones and some early Bluetooth USB dongles. Common with ESP8266 and ESP32 chips (40 MHz is also supported). Used in some WiFi, WLan, Bluetooth, BLE, NFC and GSM systems. [22]
26.2144Popular for 102.4 kS/s, 204.8 kS/s or similar sampling systems, when a power-of-two size FFT follows the sampling. In this case the FFT frequency bins end up to be at "nice" frequencies for humans. Also allows integer division to 25 Hz and multiples of 25 Hz (50 Hz, 100 Hz, 200 Hz); 26.2144 MHz = 100×218 = 25×220.
26.5625 Fibre Channel Quadrupled to 106.250 MHz Fibre Channel clock
26.601712 PAL 6x the 4.43361875 color subcarrier frequency; clock crystal of the PAL region NES consoles, divided by 16 to CPU clock (1.662607 MHz), see 21.47727 MHz for NTSC region systems [26]
26.800 SDTV Common crystal in SDTV video handling systems (especially NTSC, square-pixel, or dual-mode systems; CCIR601 systems also use 24.576 MHz)
26.8436Digital signal generatorExact frequency is 2^28/10 Hz. Used to drive a DDS synthesizer with 28-bit accumulator; gives output from 0 to 2.68435 MHz in 0.1 Hz steps. Instek SFG-1000 series is one example.
26.975RC27 MHz band, band 0/1 (grey/brown), "split" frequency; radio-controlled models of cars, boats, aircraft [29]
26.995RC27 MHz band, band 1 (brown); radio-controlled models of cars, boats, aircraft
27.000 SDTV Master clock for PAL/NTSC DVD players, Digital TV receivers, some modems etc. (27 MHz is an exact multiple of the PAL and NTSC line frequencies). Master clock for MPEG-2 video systems (also uses multiples - 54 MHz, 81 MHz). Pixel clock for SDTV (720×480p@59.94, 720×576p@50), divides by 2 to 13.5 MHz clock (720×480i@59.94, 720×576i@25) and by 4 to 6.75 MHz, very common
27.025RC27 MHz band, band 1/2 (brown/red), "split" frequency; radio-controlled models of cars, boats, aircraft
27.045RC27 MHz band, band 2 (red); some radio-controlled models of cars, boats, aircraft
27.075RC27 MHz band, band 2/3 (red/orange), "split" frequency; radio-controlled models of cars, boats, aircraft
27.095RC27 MHz band, band 3 (orange); some radio-controlled models of cars, boats, aircraft
27.12 RFID Twice 13.56 MHz, common contactless smartcard frequency (ISO/IEC 14443). Used in RFID/NFC systems. [22]
27.125RC27 MHz band, band 3/4 (orange/yellow), "split" frequency; radio-controlled models of cars, boats, aircraft; common crystal in vintage walkie talkies
27.145RC27 MHz band, band 4 (yellow); some radio-controlled models of cars, boats, aircraft; gate and garage door remote controls; toy walkie talkies; [30] between channels 15 and 16 of the CB radio
27.175RC27 MHz band, band 4/5 (yellow/green), "split" frequency; radio-controlled models of cars, boats, aircraft
27.195RC27 MHz band, band 5 (green); radio-controlled models of cars, boats, aircraft
27.225RC27 MHz band, band 5/6 (green/blue), "split" frequency; radio-controlled models of cars, boats, aircraft
27.255RC27 MHz band, band 6 (blue); some radio-controlled models of cars, boats, aircraft
27.456 GPS Reference clock for some GPS systems. Available as TCXO. [24]
27.648 DECT 115200Yes check.svgUART clock allows integer division to common baud rates up to 115,200(×16×15) or 576,000(×16×3). Twice the 13.824 MHz of DECT master clock.
28.060 Amateur Radio A common QRP frequency (10-meter band). See also 7.025 MHz.
28.3046 3270 Twelve times the coax bit rate of IBM 3270 networks. [31]
28.224modems7200audioUART clock allows integer division to common baud rates up to 7,200(×16×245) or 14,400(×8×245); used in some faxes and modems; modem and fax rates (504×56000, 580×48000, 840×33600, 980×28800, 1960×14400, 2352×12000, etc.); also divides to common audio frequencies (147×192000, 588×48000, 640×44100, 1280×22050, 2560×11025)
28.322 VGA Common Video Graphics Array pixel clock (i.e., 720×350/400@70 Hz, 31.46889 kHz horizontal) [28]
28.37516
28.375		 PAL Master clock for some PAL CCD cameras; 2 periods per pixel, 1816 periods per scan line, 567500 periods per frame. With frequency of 28.37516 video clock for all PAL Amiga computers.
28.636363 NTSC Master clock for some NTSC CCD cameras. Video clock for all NTSC Amiga computers. Twice the 14.31818 MHz frequency, shares its other uses, e.g. seed clock of PC ISA bus. Exactly 315/11 MHz. 8×3.598545 MHz of the NTSC colorburst. Used in some microcontroller based NTSC console emulators. See 35.46895 MHz for corresponding PAL systems. [32]
28.80014400 DVB-T Used in some DVB-T USB dongle TV receivers, namely the RTL-SDR ones used for software-defined radio. UART clock allows integer division to common baud rates up to 14,400(×16×125) or 28,800(×8×125).
29.4912921600UART clock allows integer division to common baud rates up to 921,600(×16×2).
29.50 SDTV SDTV PAL 4:3 pixel clock (768×576p@50), square pixels
30.000Common CPU clock. Used in some ISM wireless systems. [22]
30.240 VGA Early Macintosh video pixel clock (VGA 640×480@66 Hz) [28]
30.7203G38400Yes check.svgA 3G reference clock; twice the 15.36 MHz, 8x the 3.84 MHz WCDMA chip rate. Reference clock in W-CDMA systems; can be multiplied by 16 to 491.52 MHz common for driving DACs in WCDMA wireless base stations or by 32 to 983.04 MHz for UMTS base stations or by 8 to 245.76 MHz, other common DAC sampling frequency. [33] UART clock; allows integer division to common baud rates (800×38400 baud or 800×32×1,200 baud). Available as VCXO, TCXO and OCXO.
31.3344115200 UART clock; allows integer division to common baud rates (272×115200 baud or 272×96×1,200 baud). CPU frequency or multiple of it (as well as video and system master clocks) in older Apple Macintosh computers (Classic, LC, etc.).
31.50 VGA VGA pixel clock (VESA modes 640×350@85, 640×400@85, VGA 640×480@72/75, all hsync 37.9 kHz) [28]
32.000 LoRa common crystal for LoRa RF chips by Semtech, available as TCXO; also used for Zigbee, 6LowPan, RF4CE, Bluetooth and BLE [22]
32.75 SDTV SDTV NTSC pixel clock (864×480p@59.94, close to FWVGA)
32.768Yes check.svgAllows binary division to 1 kHz (215×1 kHz). Reference clock of some consumer GPS receivers. Commonly available as TCXO and OCXO.
33.1776115200 UART clock; allows integer division to common baud rates. (288×115200 baud or 288×96×1,200 baud)
33.33Common CPU clock, PCI bus clock
33.554432Yes check.svg 225 allows binary division to 1 Hz and 32.768 kHz. Real-time clock; also for DDS generators with 1 Hz step
33.8688115200audioUsed in CD-DA systems and CD-ROM drives; allows integer division to 44.1 kHz (768×44.1 kHz), 22.05 kHz, and 11.025 kHz. 12x2.8224 MHz (DSD64 bitrate). Also allows integer division to common UART baud rates up to 115200. Available as a TCXO. Frequencies also used are 11.2896 MHz, 16.9344 MHz, 22.5972 MHz and 45.1584 MHz.
34.368 E3 38400 E3 data rate clock. UART clock; allows integer division to common baud rates. (895×38400 baud or 895×32×1200 baud)
34.950RC35 MHz band, channel 55; radio-controlled models of aircraft [34]
34.960RC35 MHz band, channel 56; radio-controlled models of aircraft; VGA pixel clock (GTF mode PAL 768×576@60, hsync 35.82 kHz)
34.970RC35 MHz band, channel 57; radio-controlled models of aircraft
34.980RC35 MHz band, channel 58; radio-controlled models of aircraft
34.990RC35 MHz band, channel 59; radio-controlled models of aircraft
35.000RC35 MHz band, channel 60; radio-controlled models of aircraft
35.010RC35 MHz band, channel 61; radio-controlled models of aircraft
35.020RC35 MHz band, channel 62; radio-controlled models of aircraft
35.0208115200 UART clock; allows integer division to common baud rates. (304×115200 baud or 304×96×1,200 baud)
35.030RC35 MHz band, channel 63; radio-controlled models of aircraft
35.040RC35 MHz band, channel 64; radio-controlled models of aircraft
35.050RC35 MHz band, channel 65; radio-controlled models of aircraft
35.060RC35 MHz band, channel 66; radio-controlled models of aircraft
35.070RC35 MHz band, channel 67; radio-controlled models of aircraft
35.080RC35 MHz band, channel 68; radio-controlled models of aircraft
35.090RC35 MHz band, channel 69; radio-controlled models of aircraft
35.100RC35 MHz band, channel 70; radio-controlled models of aircraft
35.110RC35 MHz band, channel 71; radio-controlled models of aircraft
35.120RC35 MHz band, channel 72; radio-controlled models of aircraft
35.130RC35 MHz band, channel 73; radio-controlled models of aircraft
35.140RC35 MHz band, channel 74; radio-controlled models of aircraft
35.150RC35 MHz band, channel 75; radio-controlled models of aircraft
35.160RC35 MHz band, channel 76; radio-controlled models of aircraft
35.170RC35 MHz band, channel 77; radio-controlled models of aircraft
35.180RC35 MHz band, channel 78; radio-controlled models of aircraft
35.190RC35 MHz band, channel 79; radio-controlled models of aircraft
35.200RC35 MHz band, channel 80; radio-controlled models of aircraft
35.210RC35 MHz band, channel 81; radio-controlled models of aircraft
35.220RC35 MHz band, channel 82; radio-controlled models of aircraft
35.230RC35 MHz band, channel 83; radio-controlled models of aircraft
35.240RC35 MHz band, channel 84; radio-controlled models of aircraft
35.250RC35 MHz band, channel 85; radio-controlled models of aircraft
35.2512115200 UART clock; allows integer division to common baud rates. (306×115200 baud or 306×96×1,200 baud)
35.260RC35 MHz band, channel 86; radio-controlled models of aircraft
35.270RC35 MHz band, channel 87; radio-controlled models of aircraft
35.280RC35 MHz band, channel 88; radio-controlled models of aircraft
35.290RC35 MHz band, channel 89; radio-controlled models of aircraft
35.300RC35 MHz band, channel 90; radio-controlled models of aircraft
35.328 DSL 38400 UART clock; allows integer division to common baud rates. (64×552000 baud, 256×138000 baud, 460×38400 baud or 460×32×1,200 baud); DSL clock: 2×17.664 MHz (VDSL) ... 16×2.208 MHz (ADSL ADC sampling rate)
35.46895
35.468		 PAL 8×4.43361875 MHz of the PAL colorburst (color subcarrier). Used in some microcontroller based PAL console emulators. 
See 28.6363 MHz for the corresponding NTSC systems. [32]
35.50 VGA VGA pixel clock (VESA mode 720×400@85, hsync 37.9 kHz) [28]
36.000 VGA/SDTV Video Graphics Array pixel clock (VESA modes VGA 640×480@85 with hsync 43.3 kHz, SVGA 800×600@56 with hsync 35.2 kHz. [28] Pixel clock for SDTV PAL/NTSC (FWVGA 960×480p@59.94, 960×576p@50).
36.864460800audioYes check.svgUART clock allows integer division to common baud rates up to 460,800(×16×5). Audio clock allows integer division for 48 / 96 / 192 ksps.
37.400Used in some WiFi and Bluetooth systems. [22]
38.4003G38400 DVB UART clock; allows integer division to common baud rates (500×38,400 baud or 500×32×1,200 baud). Also used as a 3G reference clock, due to being a second (2×19.2 MHz) least common multiple of W-CDMA chip rate 3.84 MHz (5x) and 200 kHz channel raster (96x). [21] Also used in some DVB receiver chipsets. Used as reference clock in some Bluetooth systems, DECT phones, WiFi. [22]
38.88 DS1/T1/E1 Used in DS1/T1/E1 systems as a packet clock (2×19.44 MHz). Commonly available as TCXO and OCXO.
39.000 GSM/UMTS 3×13 MHz. Commonly used as a reference clock for GSM and UMTS handsets. (39 MHz is exactly 144 times the GSM bit rate). Available as TCXO.
39.33 SDTV SDTV PAL 16:9 pixel clock (1024 WSWGA, 1024×576p@50), square pixels
40.000Common CPU clock, WiFi, OFDM. FPU oscillator for Commodore A3630 card and found in dual band miniPCIe WiFi cards. VGA pixel clock (VESA mode SVGA 800×600@60 with hsync 37.9 kHz). Allows binary division to 10 MHz. Used with ESP8266 and ESP32 chips (26 MHz is also supported and seems more common). Used in some WiFi, Bluetooth and BLE, RFID/NFC, SimpleLink systems. [22]
40.320115200 UART clock; allows integer division to common baud rates. (350×115200 baud or 350×96×1,200 baud)
40.655RC40 MHz band, channel 50; radio-controlled models of cars, boats [35]
40.665RC40 MHz band, channel 66; radio-controlled models of cars, boats
40.675RC40 MHz band, channel 51; radio-controlled models of cars, boats
40.680common crystal in garage door remotes and other remote controls; multiply by 32/3 to 433.92 MHz
40.685RC40 MHz band, channel 52; radio-controlled models of cars, boats
40.695RC40 MHz band, channel 53; radio-controlled models of cars, boats
40.705RC40 MHz band, channel 70; radio-controlled models of cars, boats
40.715RC40 MHz band, channel 54; radio-controlled models of cars, boats
40.725RC40 MHz band, channel 55; radio-controlled models of cars, boats
40.735RC40 MHz band, channel 56; radio-controlled models of cars, boats
40.745RC40 MHz band, channel 74; radio-controlled models of cars, boats
40.755RC40 MHz band, channel 75; radio-controlled models of cars, boats
40.765RC40 MHz band, channel 57; radio-controlled models of cars, boats
40.775RC40 MHz band, channel 58; radio-controlled models of cars, boats
40.775RC40 MHz band, channel 77; radio-controlled models of cars, boats
40.785RC40 MHz band, channel 59; radio-controlled models of cars, boats
40.795RC40 MHz band, channel 79; radio-controlled models of cars, boats
40.805RC40 MHz band, channel 80; radio-controlled models of cars, boats
40.815RC40 MHz band, channel 81; radio-controlled models of cars, boats
40.825RC40 MHz band, channel 82; radio-controlled models of cars, boats
40.835RC40 MHz band, channel 83; radio-controlled models of cars, boats
40.875RC40 MHz band, channel 85; radio-controlled models of cars, boats
40.885RC40 MHz band, channel 86; radio-controlled models of cars, boats
40.915RC40 MHz band, channel 87; radio-controlled models of cars, boats
40.935RC40 MHz band, channel 93; radio-controlled models of cars, boats
40.945RC40 MHz band, channel 94; radio-controlled models of cars, boats
40.960Allows binary division to 10 kHz (212×10 kHz)
40.975RC40 MHz band, channel 91; radio-controlled models of cars, boats
40.985RC40 MHz band, channel 92; radio-controlled models of cars, boats
40.985RC40 MHz band, channel 98; radio-controlled models of cars, boats
42.93 VGA VGA pixel clock (GTF mode PAL 768×576@72, hsync 43.27 kHz) [28]
43.16 VGA VGA pixel clock (GTF mode VGA 640×480@100, hsync 50.9 kHz) [28]
44.736 DS3 38400 DS3 data rate clock. UART clock; allows integer division to common baud rates. (1165×38400 baud or 1165×32×1200 baud)
44.90 VGA VGA pixel clock (industry standard XGA 1024×768i@43, hsync 35.5 kHz) [28]
45.158457600audioUsed in CD-DA systems and CD-ROM drives; allows binary division to 44.1 kHz (1024×44.1 kHz), 22.05 kHz, and 11.025 kHz. 16x2.8224 MHz (DSD rate). UART clock allows integer division to common baud rates up to 57,600(×16×49) or 115,200(×8×49). Available as a TCXO. Frequencies also used are 11.2896 MHz, 16.9344 MHz, 22.5972 MHz and 33.8688 MHz.
45.51 VGA VGA pixel clock (GTF mode PAL 768×576@75, hsync 45.15 kHz) [28]
48.000 USB VGA/HDTV found in old VGA cards, [36] High-speed USB (48 MHz × 10 = 480 Mbit/s). HDTV pixel clock (1280×1080i@25), variant compatible with CRT-based 31.250 kHz horizontal deflection HDTVs. Used in some WiFi and Bluetooth systems. [22]
49.1520 FireWire audioDigital audio systems - DAT, MiniDisc, AC'97, sound cards; 1024×48 kHz (210×48 kHz); also used as bus reference clock in FireWire systems (with accuracy of 100 ppm). Twice the more-standard frequency of 24.576 MHz. 6x8.192 MHz. Available as TCXO.
49.408 DS1 32x1.544, the bit clock for DS1 systems (±32 ppm, ANSI T1.102).
49.450549 HDTV HDTV NTSC pixel clock (1280×1080i@29.97, 1280×1080p@29.97); 49.5/1.001
49.500 HDTV HDTV ATSC pixel clock (1280×1080i@25/30, 1280×1080p@24/25/30). VGA pixel clock (VESA 800×600@75, hsync 46.9 kHz)
49.830
49.860
49.890		RCtoy remote controls, walkie-talkies
50.000 Ethernet Fast Ethernet (2×25 MHz), VGA pixel clock (VESA mode 800×600@72, hsync 48.1 kHz) [28] PCI Express clock source, doubled to 100 MHz. Amigakit ZorRAM memory cards.
50.09 Amateur Radio A common QRP frequency (6-meter band). Other crystal can be 50.4 MHz. 3rd overtone. See also 7.025 MHz.
51.840 SONET 115200VGA UART clock; allows integer division to common baud rates. (450×115200 baud or 450×96×1,200 baud); SONET STS-1 frequency (with accuracy of 20 =ppm); [8] VGA pixel clock (GTF mode 768×576@85, hsync 51.42 kHz). Can be generated from 6.48 MHz xtal.
52.000Used in some WiFi, WLAN and GSM systems. [22]
52.416 modems 115200 UART clock; allows integer division to common baud rates. (455×115200 baud or 455×96×1,200 baud) and to modem and fax rates (936×56000, 1092×48000, 1560×33600, 1820×28800, 3640×14400, 4368×12000, etc.); also divides to some common audio frequencies (273×192000, 1092×48000)
53.125 Fibre Channel Fibre Channel clock
54.000 PAL/NTSC/HDTV Raspberry Pi 4 (BCM2711) main clock crystal (19.2 MHz for Raspberry Pi 3 and earlier). Clock for digital video systems (27 MHz is an exact multiple of the PAL and NTSC line frequencies). 2x the 27 MHz master clock for MPEG-2 video systems (see also 81 MHz). HDTV pixel clock (1440×1080i@25), variant compatible with CRT-based 31.250 kHz horizontal deflection HDTVs.
55.6319 HDTV HDTV NTSC pixel clock (4:3 1440×1080i@29.97, 1440×1080p@23.976/29.97); 55.6875/1.001
55.6875 HDTV HDTV ATSC pixel clock (4:3 1440×1080i@25/30, 1440×1080p@24/25/30)
56.30 VGA VGA pixel clock (VESA mode SVGA 800×600@85, hsync 53.7 kHz) [28]
56.448 modems 1152002×28.224 MHz; used in some faxes and modems; UART clock, allows integer division to common baud rates (490×115200, 1024×38400, 2048×19200, etc.) and to modem and fax rates (1008×56000, 1160×48000, 1680×33600, 1960×28800, 3920×14400, 4704×12000, etc.); also divides to common audio frequencies (294×192000, 1176×48000, 1280×44100, 2560×22050, 5120×11025)
61.440 WCDMA/3G Used in wireless base stations; 2x30.72 MHz
62.57 VGA VGA pixel clock (GTF mode PAL 768×576@100, hsync 61.1 kHz) [28]
65.00 VGA VGA pixel clock (VESA mode XGA 1024×768@60, hsync 48.4 kHz) [28]
66.667common CPU clock, PCI bus clock
67.108864Yes check.svg 226 allows binary division to 1 Hz and 32.768 kHz. Real-time clock; also for DDS generators with 1 Hz step
68.18 VGA VGA pixel clock (GTF mode SVGA 800×600@100, hsync 63.6 kHz) [28]
70.656 DSL 38400(2x35.328) UART clock; allows integer division to common baud rates. (128×552000 baud, 512×138000 baud, 920×38400 baud or 920×32×1,200 baud);DSL clock: 4×17.664 MHz (VDSL) ... 32×2.208 MHz (ADSL ADC sampling rate)
72.000 HDTV HDTV pixel clock (FHD/2K 1920×1080i@25), variant compatible with CRT-based 31.250 kHz horizontal deflection HDTVs
74.1758242
74.176		 HDTV HDTV NTSC pixel clock (HD/WXGA 1280×720p@23.976/29.97/59.94, 1920×1080i@29.97, 1920×1080p@23.976/29.97); 74.25/1.001; very common Multiply by 91/250 to get 27 MHz.
74.250 HDTV HDTV ATSC pixel clock (HD/WXGA 1280×720p@24/25/30/50/60, 1920×1080i@25/30, 1920×1080p@24/25/30); very common; also 1920×1080i@25, variant compatible with CRT-based 31.250 kHz horizontal deflection HDTVs. Multiply by 4/11 to get 27 MHz.
75.0 VGA VGA pixel clock (VESA mode XGA 1024×768@70, hsync 56.5 kHz) [28]
77.760 SONET/SDH115200 UART clock; allows integer division to common baud rates. (675×115200 baud or 675×96×1,200 baud). Commonly available as TCXO and OCXO. Multiplies to clock for communication for SONET/SDH/ATM, 1.5×51.840 MHz (SONET STS-1 frequency). Can be generated from 19.44 MHz xtal.
78.125 Ethernet Gigabit Ethernet, multiplies to 10 GHz MAC-side bitrate, post-serdes; 78.125 MHz = 1/132 of 10.3125 GHz, 1/128 of 10.0 GHz; often generated from 19.53125 MHz xtal
78.8 VGA VGA pixel clock (VESA mode XGA 1024×768@75, hsync 60.0 kHz) [28]
80.000audiocommon CPU clock; used in some audio applications, available as TCXO. Allows binary division to 10 MHz.
80.566406 Ethernet Gigabit Ethernet. Multiplies (×128) to 10.3125 GHz, copper wire bit rate. Can be generated from 20.141601 xtal.
81.000 PAL/NTSC/SDTV Clock for digital video systems (27 MHz is an exact multiple of the PAL and NTSC line frequencies). 3x the 27 MHz master clock for MPEG-2 video systems (see also 81 MHz).
81.62 VGA VGA pixel clock (GTF mode XGA+ 1152×864@60, hsync 53.70 kHz) [28]
83.46 VGA VGA pixel clock (GTF mode WXGA 1280×800@60, hsync 49.68 kHz) [28]
85.86 VGA VGA pixel clock (GTF mode FWXGA 1368×768@60, hsync 47.7 kHz) [28]
88.75 VGA VGA pixel clock (WXGA+ 1440×900@60)
92.160 WCDMA/3G Used in wireless base stations; 3x30.72 MHz
94.5 VGA VGA pixel clock (VESA mode XGA 1024×768@85, hsync 68.7 kHz) [28]
98.901099 HDTV HDTV NTSC pixel clock (1280×1080p@59.94); 2x49.450549, 99/1.001
99.000 HDTV HDTV ATSC pixel clock (1280×1080p@50/60)
100.000 108 allows decade division to 1 Hz and 1 kHz. PCI Express clock. [37] Standard frequency, available as OCXO.
106.250 Fibre Channel Fibre Channel clock for 1.0625 gigabaud rate
106.47 VGA VGA pixel clock (GTF mode WXGA+ 1440×900@60, hsync 55.92 kHz) [28]
106.5radioUsed as an IF LO in microwave transceivers, e.g. on the amateur 10 GHz band. Multiplied by 96 to produce 10.224 GHz signal. Available as OCXO.
108.0 VGA VGA pixel clock (VESA modes XGA+ 1152×864@75 with hsync 675 kHz, SXGA-/UVGA 1280×960@60 with hsync 60.0 kHz, SXGA 1280×1024@60 with hsync 64 kHz) [28]
111.2638 HDTV HDTV NTSC pixel clock (4:3 1440×1080p@59.94); 111.375/1.001
111.375 HDTV HDTV ATSC pixel clock (4:3 1440×1080p@50/60); 2x55.6875
113.31 VGA VGA pixel clock (GTF mode XGA 1024×768@100, hsync 81.4 kHz) [28]
116radioUsed as an IF LO in 144 MHz transverters. Available as TCXO. Sometimes used as GPS-disciplined OCXO.
119.65 VGA VGA pixel clock (GTF mode XGA+ 1152×864@85, hsync 77.1 kHz) [28]
122.61 VGA VGA pixel clock (GTF mode SXGA+ 1400×1050@60, hsync 65.22 kHz) [28]
122.880 WCDMA/3G Standard frequency, available as TCXO, VCXO. Used in wireless base stations; 4x30.72 MHz
124.54 VGA VGA pixel clock (GTF mode SXGA-/UVGA 1280×960@72, hsync 72.07 kHz) [28]
125.000 Ethernet Gigabit Ethernet GMII GTXCLK clock, FDDI clock
129.86 VGA VGA pixel clock (GTF mode SXGA-/UVGA 1280×960@75, hsync 75.15 kHz) [28]
134.217728Yes check.svg 227 allows binary division to 1 Hz and 32.768 kHz. Real-time clock; also for DDS generators with 1 Hz step
135.0 VGA VGA pixel clock (VESA mode SXGA 1280×1024@75, hsync 80.0 kHz) [28]
143.47 VGA VGA pixel clock (GTF mode XGA+ 1152×864@100, hsync 91.5 kHz) [28]
147.14 VGA VGA pixel clock (GTF mode WSXGA+ 1680×1050@60, hsync 65.22 kHz) [28]
148.351648 HDTV SMPTE 424, HDTV NTSC pixel clock (FHD/2K 1920×1080p@59.94); 148.5/1.001. Multiply by 91/500 to get 27 MHz.
148.5 HDTV/HDMI SMPTE 424, HDTV ATSC pixel clock (FHD/2K 1920×1080p@50/60); 2x74.25. VGA pixel clock (VESA mode 1280×960@85, hsync 85.9 kHz). Standard HDMI pixel clock (4k YUV 4:2:0@30). Multiply by 4/22 to get 27 MHz.
149.34 VGA VGA pixel clock (GTF mode SXGA+ 1400×1050@72, hsync 78.77 kHz) [28]
150.000common reference oscillator, TCXO
153.600 WCDMA/3G Standard frequency. Used in wireless base stations, available as TCXO, VCXO. 5x30.72 MHz. Popular frequency of SAW filters for intermediate frequency in microwave systems.
154.0 VGA VGA pixel clock (WUXGA 1920×1200@60)
155.520 SONET/SDH3×51.840 MHz (SONET STS-1 frequency), SONET/SDH clock. Can be generated from 19.44 MHz xtal.
155.85 VGA VGA pixel clock (GTF mode SXGA+ 1400×1050@75, hsync 82.2 kHz) [28]
156.25 Ethernet 10 Gigabit Ethernet clock, 64-bit signal [38] [39] Multiplies by 64 to 10.0 GHz (MAC-side serial bitrate) or by 66 to 10.3125 GHz (wire-side serial bitrate, after encoding). In video-over-IP systems, often with 148.5 and 148.351648 MHz. [40]
157.5 VGA VGA pixel clock (VESA mode SXGA 1280×1024@85, hsync 91.1 kHz) [28]
161.132812 Ethernet Gigabit Ethernet, 66-bit signal. [38] [39] Multiplies (×64) to 10.3125 GHz, copper wire bit rate. Can be generated from 20.141601 xtal.
162.0 VGA VGA pixel clock (VESA mode UXGA 1600×1200@60, hsync 75.0 kHz) [28]
165.0 HDMI/DVI HDMI/DVI serial clock for 1080p@60 (TMDS encoding)
175.5 VGA VGA pixel clock (VESA mode UXGA 1600×1200@65, hsync 81.3 kHz) [28]
178.99 VGA VGA pixel clock (GTF mode SXGA-/UVGA 1280×960@100, hsync 101.7 kHz) [28]
179.26 VGA VGA pixel clock (GTF mode SXGA+ 1400×1050@85, hsync 93.76 kHz) [28]
184.320 WCDMA/3G Used in wireless base stations; 6x30.72 MHz
187.50 Ethernet 10x18.75 MHz; see also 75 MHz, 150 MHz
189.0 VGA VGA pixel clock (VESA mode UXGA 1600×1200@70, hsync 87.5 kHz) [28]
190.96 VGA VGA pixel clock (GTF mode SXGA 1280×1024@100, hsync 108.5 kHz) [28]
193.16 VGA VGA pixel clock (GTF mode WUXGA 1920×1200@60, hsync 74.52 kHz) [28]
196.608 E1 Allows division to 1 kHz (3×2^16×1 kHz). Bit clock for E1 systems. 48x4.096 MHz, 96x2.048 MHz.
202.5 VGA VGA pixel clock (VESA mode UXGA 1600×1200@75, hsync 93.8 kHz) [28]
204.8 VGA VGA pixel clock (VESA mode 1792×1344@60, hsync 83.6 kHz) [28]
214.39 VGA VGA pixel clock (GTF mode SXGA+ 1400×1050@100, hsync 111.2 kHz) [28]
218.3 VGA VGA pixel clock (VESA mode 1856×1392@60, hsync 86.3 kHz) [28]
229.5 VGA VGA pixel clock (VESA mode UXGA 1600×1200@85, hsync 106.3 kHz) [28]
234.0 VGA VGA pixel clock (VESA mode 1920×1440@60, hsync 90.0 kHz) [28]
234.59 VGA VGA pixel clock (QHD 2560×1440@60)
261.0 VGA VGA pixel clock (VESA mode 1792×1344@75, hsync 106.3 kHz) [28]
268.435456Yes check.svg 228 allows binary division to 1 Hz and 32.768 kHz. Real-time clock; also for DDS generators with 1 Hz step
280.64 VGA VGA pixel clock (GTF mode UXGA 1600×1200@100, hsync 127.1 kHz) [28]
288.0 VGA VGA pixel clock (VESA mode 1856×1392@75, hsync 112.5 kHz) [28]
297.0 VGA/HDMI VGA pixel clock (VESA mode 1920×1440@75, hsync 112.5 kHz). [28] High-speed HDMI pixel clock (2x148.5, 4k YUV 4:2:0@60, RGB@30).
311.04 SONET/SDH6×51.840 MHz (SONET STS-1 frequency), SONET/SDH clock.
312.5 Ethernet Gigabit Ethernet, multiplies (×32) to 10 GHz MAC-side bitrate, or (×33) to 10.3125 GHz copper-wire serial bitrate; often generated from 19.53125 MHz xtal
312.787 VGA VGA pixel clock (21.5:9 3440×1440@60)
radio (ISM)SAW resonators for Chinese 315 MHz ISM band RF remote control fobs
322.265625 Ethernet Gigabit Ethernet, PHY, 66-bit signal. Multiplies (×32) to 10.3125 GHz, copper wire bit rate. Can be generated from 20.141601 xtal.
336.375 VGA VGA pixel clock (QHD 2560×1440@85)
radio (ISM)SAW resonators for 433.92 MHz ISM band RF remote control fobs
448.5 VGA VGA pixel clock (21.5:9 3440×1440@85)
483.120 VGA VGA pixel clock (QHD 2560×1440@120)
531.52 VGA VGA pixel clock (4K UHD 3440×1440@100)
533.250 VGA VGA pixel clock (4K UHD 3840×2160@60)
586.586 VGA VGA pixel clock (QHD 2560×1440@144)
622.08 SONET/SDH12×51.840 MHz (SONET STS-1 frequency), SONET/SDH clock.
625.0 Ethernet Gigabit Ethernet, multiplies (×16) to 10 GHz MAC-side bitrate
644.160 VGA VGA pixel clock (21.5:9 3440×1440@120)
678.100 VGA VGA pixel clock (QHD 2560×1440@165)
1075.804 VGA VGA pixel clock (4K UHD 3840×2160@120)

Related Research Articles

<span class="mw-page-title-main">Radioteletype</span> Radio linked electromechanical communications system

Radioteletype (RTTY) is a telecommunications system consisting originally of two or more electromechanical teleprinters in different locations connected by radio rather than a wired link. Radioteletype evolved from earlier landline teleprinter operations that began in the mid-1800s. The US Navy Department successfully tested printing telegraphy between an airplane and ground radio station in 1922. Later that year, the Radio Corporation of America successfully tested printing telegraphy via their Chatham, Massachusetts, radio station to the R.M.S. Majestic. Commercial RTTY systems were in active service between San Francisco and Honolulu as early as April 1932 and between San Francisco and New York City by 1934. The US military used radioteletype in the 1930s and expanded this usage during World War II. From the 1980s, teleprinters were replaced by personal computers (PCs) running software to emulate teleprinters.

<span class="mw-page-title-main">Superheterodyne receiver</span> Type of radio receiver

A superheterodyne receiver, often shortened to superhet, is a type of radio receiver that uses frequency mixing to convert a received signal to a fixed intermediate frequency (IF) which can be more conveniently processed than the original carrier frequency. It was invented by French radio engineer and radio manufacturer Lucien Lévy. Virtually all modern radio receivers use the superheterodyne principle.

<span class="mw-page-title-main">Crystal oscillator</span> Electronic oscillator circuit

A crystal oscillator is an electronic oscillator circuit that uses a piezoelectric crystal as a frequency-selective element. The oscillator frequency is often used to keep track of time, as in quartz wristwatches, to provide a stable clock signal for digital integrated circuits, and to stabilize frequencies for radio transmitters and receivers. The most common type of piezoelectric resonator used is a quartz crystal, so oscillator circuits incorporating them became known as crystal oscillators. However, other piezoelectric materials including polycrystalline ceramics are used in similar circuits.

<span class="mw-page-title-main">Digital Visual Interface</span> Standard for transmitting digital video to a display

Digital Visual Interface (DVI) is a video display interface developed by the Digital Display Working Group (DDWG). The digital interface is used to connect a video source, such as a video display controller, to a display device, such as a computer monitor. It was developed with the intention of creating an industry standard for the transfer of uncompressed digital video content.

<span class="mw-page-title-main">Universal asynchronous receiver-transmitter</span> Computer hardware device

A universal asynchronous receiver-transmitter is a peripheral device for asynchronous serial communication in which the data format and transmission speeds are configurable. It sends data bits one by one, from the least significant to the most significant, framed by start and stop bits so that precise timing is handled by the communication channel. The electric signaling levels are handled by a driver circuit external to the UART. Common signal levels are RS-232, RS-485, and raw TTL for short debugging links. Early teletypewriters used current loops.

<span class="mw-page-title-main">Radio clock</span> Type of clock which self-synchronizes its time using dedicated radio transmitters

A radio clock or radio-controlled clock (RCC), and often colloquially referred to as an "atomic clock", is a type of quartz clock or watch that is automatically synchronized to a time code transmitted by a radio transmitter connected to a time standard such as an atomic clock. Such a clock may be synchronized to the time sent by a single transmitter, such as many national or regional time transmitters, or may use the multiple transmitters used by satellite navigation systems such as Global Positioning System. Such systems may be used to automatically set clocks or for any purpose where accurate time is needed. Radio clocks may include any feature available for a clock, such as alarm function, display of ambient temperature and humidity, broadcast radio reception, etc.

<span class="mw-page-title-main">Clock rate</span> Frequency at which CPU chip or core is operating

In computing, the clock rate or clock speed typically refers to the frequency at which the clock generator of a processor can generate pulses, which are used to synchronize the operations of its components, and is used as an indicator of the processor's speed. It is measured in the SI unit of frequency hertz (Hz).

<span class="mw-page-title-main">Real-time clock</span> Circuit in a computer that maintains accurate time

A real-time clock (RTC) is an electronic device that measures the passage of time.

<span class="mw-page-title-main">Voltage-controlled oscillator</span> Oscillator with frequency controlled by a voltage input

A voltage-controlled oscillator (VCO) is an electronic oscillator whose oscillation frequency is controlled by a voltage input. The applied input voltage determines the instantaneous oscillation frequency. Consequently, a VCO can be used for frequency modulation (FM) or phase modulation (PM) by applying a modulating signal to the control input. A VCO is also an integral part of a phase-locked loop. VCOs are used in synthesizers to generate a waveform whose pitch can be adjusted by a voltage determined by a musical keyboard or other input.

Synchronous and asynchronous transmissions are two different methods of transmission synchronization. Synchronous transmissions are synchronized by an external clock, while asynchronous transmissions are synchronized by special signals along the transmission medium.

<span class="mw-page-title-main">Dallas Semiconductor</span> Defunct American semiconductor company

Dallas Semiconductor, acquired by Maxim Integrated in 2002 for $2.5 billion, then acquired by Analog Devices in 2021, was a company that designed and manufactured analog, digital, and mixed-signal semiconductors. Its specialties included communications products, microcontrollers, battery management, thermal sensing and thermal management, non-volatile random-access memory, microprocessor supervisors, delay lines, silicon oscillators, digital potentiometers, real-time clocks, temperature-compensated crystal oscillators (TCXOs), iButton, and 1-Wire products.

<span class="mw-page-title-main">8250 UART</span>

The 8250 UART is an integrated circuit designed for implementing the interface for serial communications. The part was originally manufactured by the National Semiconductor Corporation. It was commonly used in PCs and related equipment such as printers or modems. The 8250 included an on-chip programmable bit rate generator, allowing use for both common and special-purpose bit rates which could be accurately derived from an arbitrary crystal oscillator reference frequency.

<span class="mw-page-title-main">R8C</span>

The Renesas R8C is a 16-bit microcontroller that was developed as a smaller and cheaper version of the Renesas M16C. It retains the M16C's 16-bit CISC architecture and instruction set, but trades size for speed by cutting the internal data bus from 16 bits to 8 bits. It is available in a number of different versions with varying amounts of flash memory and SRAM.

<span class="mw-page-title-main">WDC 65C134</span>

The Western Design Center (WDC) W65C134S is an 8-bit CMOS microcontroller based on a W65C02S processor core, which is a superset of the MOS Technology 6502 processor.

<span class="mw-page-title-main">Parallax Propeller</span> Multi-core microcontroller

The Parallax P8X32A Propeller is a multi-core processor parallel computer architecture microcontroller chip with eight 32-bit reduced instruction set computer (RISC) central processing unit (CPU) cores. Introduced in 2006, it is designed and sold by Parallax, Inc.

A frequency synthesizer is an electronic circuit that generates a range of frequencies from a single reference frequency. Frequency synthesizers are used in many modern devices such as radio receivers, televisions, mobile telephones, radiotelephones, walkie-talkies, CB radios, cable television converter boxes, satellite receivers, and GPS systems. A frequency synthesizer may use the techniques of frequency multiplication, frequency division, direct digital synthesis, frequency mixing, and phase-locked loops to generate its frequencies. The stability and accuracy of the frequency synthesizer's output are related to the stability and accuracy of its reference frequency input. Consequently, synthesizers use stable and accurate reference frequencies, such as those provided by a crystal oscillator.

The Mitsubishi 740, also known as MELPS 740, is a series of 8-bit CMOS microcontrollers and microprocessors with an enhanced MOS Technology 6502 compatible core based on the expanded WDC 65C02. The ICs were manufactured by Mitsubishi Electric during the 1980s and 1990s.

<span class="mw-page-title-main">Vortex86</span> X86-compatible system-on-a-chip

The Vortex86 is a computing system-on-a-chip (SoC) based on a core compatible with the x86 microprocessor family. It is produced by DM&P Electronics, but originated with Rise Technology.

<span class="mw-page-title-main">STM32</span> ARM Cortex-M based Microcontrollers by STMicroelectronics

STM32 is a family of 32-bit microcontroller integrated circuits by STMicroelectronics. The STM32 chips are grouped into related series that are based around the same 32-bit ARM processor core: Cortex-M0, Cortex-M0+, Cortex-M3, Cortex-M4, Cortex-M7, Cortex-M33. Internally, each microcontroller consists of ARM processor core(s), flash memory, static RAM, debugging interface, and various peripherals.

<span class="mw-page-title-main">NXP LPC</span> Family of 32-bit microcontroller integrated circuits

LPC is a family of 32-bit microcontroller integrated circuits by NXP Semiconductors. The LPC chips are grouped into related series that are based around the same 32-bit ARM processor core, such as the Cortex-M4F, Cortex-M3, Cortex-M0+, or Cortex-M0. Internally, each microcontroller consists of the processor core, static RAM memory, flash memory, debugging interface, and various peripherals. The earliest LPC series were based on the Intel 8-bit 80C51 core. As of February 2011, NXP had shipped over one billion ARM processor-based chips.

References

  1. ↑ "DS3231 Extremely Accurate I²C-Integrated RTC/TCXO/Crystal - Maxim". Archived from the original on 16 May 2015. Retrieved 26 April 2015.
  2. ↑ Bulova [ circular reference ]
  3. ↑ "Resonator-MCU - integritytechnology". Archived from the original on 23 October 2020. Retrieved 7 June 2020.
  4. ↑ Weitzman, Barry (16 March 2008). "strange crystal frequencies". cctalk (Mailing list). Archived from the original on 5 October 2014.
  5. ↑ Instrumentation Archived 2010-09-11 at the Wayback Machine . (PDF) . Retrieved on 2010-02-08.
  6. ↑ D19 - Sensor Data. (PDF) . Retrieved on 2010-02-08.
  7. 1 2 "Requirements of Remote Keyless Entry Systems | Maxim Integra".
  8. 1 2 3 "Using clock generation chips to replace crystals and oscillators". Archived from the original on 13 July 2011. Retrieved 24 December 2009.
  9. ↑ "eHam.net". www.eham.net. Retrieved 8 April 2024.
  10. ↑ "Clock generation with non-integer clock dividing ratio".
  11. 1 2 3 4 "308MHz/315MHz/418MHz/433.92MHz Low-Power, FSK Superheterodyne Receiver" (PDF). maximintegrated.com. Retrieved 8 April 2024.
  12. ↑ "Integrated circuits. Datasheet" (PDF). pira.cz. Retrieved 8 April 2024.
  13. 1 2 3 4 QuickView - DS4026 10 MHz to 51.84 MHz TCXO. Maxim-ic.com. Retrieved on 2010-02-08.
  14. ↑ CB Radio Frequency Synthesis explanation. Glodark.co.uk. Retrieved on 2010-02-08.
  15. ↑ TSCM Handbook - Chapter 5. Dbugman.com. Retrieved on 2010-02-08.
  16. 1 2 8051 Tutorial: Instruction Set, Timing, and Low-Level Information Archived 2010-01-03 at the Wayback Machine . 8052.com. Retrieved on 2010-02-08.
  17. ↑ Blaupunkt digiceiver technology Archived 2009-07-08 at the Wayback Machine . Bluespot.co.uk. Retrieved on 2010-02-08.
  18. 1 2 CV-M50.indd Archived 2011-07-13 at the Wayback Machine Industrial Monochrome CCD Camera
  19. 1 2 3 4 5 UPB1009K NEC's low power GPS RF receiver bipolar analog + integrated circuit
  20. ↑ "MAX7058 Evaluation Kit" (PDF). maximintegrated.com. Retrieved 8 April 2024.
  21. 1 2 3 4 Clock Interface Trends from GSM/EDGE to W-CDMA Archived 2010-02-15 at the Wayback Machine Gary Levy, Silicon Laboratories Inc.
  22. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 "Jauch crystals for IoT applications" (PDF). jauch.com. Retrieved 8 April 2024.
  23. ↑ http://neil.franklin.ch/Projects/SoftVGA/Design/Video_Signals
  24. 1 2 3 4 5 "Abracon | Fox" (PDF). Retrieved 8 April 2024.
  25. ↑ "Achieving Bit-Perfect USB Audio". electronicdesign.com. 3 August 2016. Retrieved 14 November 2016.
  26. 1 2 "Cycle reference chart - Nesdev wiki".
  27. ↑ "VGA Signal Timing". www.tinyvga.com. Retrieved 8 April 2024.
  28. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 VGA timing information. Martin.hinner.info. Retrieved on 2010-02-08.
  29. ↑ Jatech Limited. "Radio Control Systems, Receivers and Crystals 27 MHz & 40 MHz, 27 MHz Crystals | Antics Online". Rccarsandtrucks.co.uk. Archived from the original on 12 December 2008. Retrieved 5 June 2010.
  30. ↑ "Disney Walkie-Talkies Pick up Crude Trucker Conversation". 23 October 2013.
  31. ↑ "Raw3270". GitHub . February 2020.
  32. 1 2 "Arduinocade". 16 September 2015.
  33. ↑ "de beste bron van informatie over open base station.Deze website is te koop!". Openbasestation.org. Archived from the original on 1 December 2008. Retrieved 5 June 2010.
  34. ↑ Jatech Limited. "Radio Control Systems, Receivers and Crystals for 35MHz Radio, 35MHz Crystals | Antics Online". Rccarsandtrucks.co.uk. Archived from the original on 9 September 2012. Retrieved 5 June 2010.
  35. ↑ Jatech Limited. "Radio Control Systems, Receivers and Crystals 27MHz and 40MHz, 40MHz Crystals | Antics Online". Rccarsandtrucks.co.uk. Archived from the original on 13 August 2009. Retrieved 5 June 2010.
  36. ↑ Low Power Multiband Beacon. Qsl.net. Retrieved on 2010-02-08.
  37. ↑ Maxim Integrated Products First 100 MHz, HCSL-output crystal oscillator for PCI Express. Mobiledevdesign.com (2008-03-20). Retrieved on 2010-02-08.
  38. 1 2 SiTime Intros Oscillator for 10 Gigabit Ethernet Applications. Dark-fiber.tmcnet.com (2009-07-29). Retrieved on 2010-02-08.
  39. 1 2 Pld architecture optimized for 10g ethernet physical layer solution Archived 2012-02-29 at the Wayback Machine . Freshpatents.com. Retrieved on 2010-02-08.
  40. ↑ "Renesas Electronics Corporation". www.renesas.com. 8 April 2024. Retrieved 8 April 2024.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.