The IBM 2321 Data Cell is a discontinued direct access storage device (DASD) for the IBM System/360. It was announced with System/360 in April, 1964. It holds up to 400 megabytes of data, with an access time of 95 milliseconds to 600 milliseconds, depending on the addressed strip position and data arrangement in each data cell. [1]
The 2321 was withdrawn from marketing in January, 1975.
The 2321 houses up to ten removable and interchangeable data cells, each containing 40 megabytes. Each data cell contains 200 strips of magnetic tape, which are the basic recording media. Strips are 2+1⁄4 inches (5.7 cm) wide and 13 inches (33 cm) long. [2] The total storage capacity is 400 megabytes or 800 million decimal digits. Up to eight 2321s can be attached to the IBM 2841 Control Unit, allowing an overall capacity of over three GB. [3]
In comparison to the contemporary IBM 2311 Disk Device, the IBM 2321 Data Cell Device holds 55 times more data, while being only seven times slower (85ms and 600ms access times respectively). One fully loaded IBM 2841 Control Unit connected with eight IBM 2321 Data Cell Devices has the capacity of 441 IBM 2311 Disk Devices, which would need to be connected to 56 IBM 2841 Control Units, which would require seven data channels.
The Data Cell makes use of three concurrently operating separate seeking systems: a servo-hydraulic one to rotate the bins to select the proper subcell, and two solenoid driven ones: one to select the correct strip tab of the ten in the subcell, and the other to select one of the five head positions, for the 20 element head (100 tracks per strip). The hydraulic fluid, Mobil DTE Light, a machine tool circulating oil, is pressurized at 1500 psi and despite a lot of folklore about oil leaks, they were very rare. The oil sump holds 5 US gallons (19 L).
Although its storage medium is tape, the 2321 is classified as a direct access storage device which can directly access a record rather than scan all the tape to find a record as would a conventional tape drive. IBM's System/360 channels addressed the 2321 as a direct access storage devices, i.e., a disk drive, with a 6-byte seek address of the form ØBBSCH (hexadecimal) where the first byte is zero and the remaining bytes address the Bin (i.e., cell and sub-cell), Strip, Cylinder and Head. [3] [4]
The 2321 was whimsically known as the "noodle picker" since the removable magnetic strips were flexible and resembled lasagna noodles. [5]
Disk storage is a general category of storage mechanisms where data is recorded by various electronic, magnetic, optical, or mechanical changes to a surface layer of one or more rotating disks. A disk drive is a device implementing such a storage mechanism. Notable types are the hard disk drive (HDD) containing a non-removable disk, the floppy disk drive (FDD) and its removable floppy disk, and various optical disc drives (ODD) and associated optical disc media.
The IBM System/360 (S/360) is a family of mainframe computer systems that was announced by IBM on April 7, 1964, and delivered between 1965 and 1978. It was the first family of computers designed to cover both commercial and scientific applications and to cover a complete range of applications from small to large. The design distinguished between architecture and implementation, allowing IBM to release a suite of compatible designs at different prices. All but the only partially compatible Model 44 and the most expensive systems use microcode to implement the instruction set, which features 8-bit byte addressing and binary, decimal, and hexadecimal floating-point calculations.
A direct-access storage device (DASD) is a secondary storage device in which "each physical record has a discrete location and a unique address". The term was coined by IBM to describe devices that allowed random access to data, the main examples being drum memory and hard disk drives. Later, optical disc drives and flash memory units are also classified as DASD.
Disk Operating System/360, also DOS/360, or simply DOS, is the discontinued first member of a sequence of operating systems for IBM System/360, System/370 and later mainframes. It was announced by IBM on the last day of 1964, and it was first delivered in June 1966. In its time, DOS/360 was the most widely used operating system in the world.
IBM manufactured magnetic disk storage devices from 1956 to 2003, when it sold its hard disk drive business to Hitachi. Both the hard disk drive (HDD) and floppy disk drive (FDD) were invented by IBM and as such IBM's employees were responsible for many of the innovations in these products and their technologies. The basic mechanical arrangement of hard disk drives has not changed since the IBM 1301. Disk drive performance and characteristics are measured by the same standards now as they were in the 1950s. Few products in history have enjoyed such spectacular declines in cost and physical size along with equally dramatic improvements in capacity and performance.
The IBM 3850 Mass Storage System (MSS) was an online tape library used to hold large amounts of infrequently accessed data. It was one of the earliest examples of nearline storage.
Cylinder-head-sector (CHS) is an early method for giving addresses to each physical block of data on a hard disk drive.
In computing, channel I/O is a high-performance input/output (I/O) architecture that is implemented in various forms on a number of computer architectures, especially on mainframe computers. In the past, channels were generally implemented with custom devices, variously named channel, I/O processor, I/O controller, I/O synchronizer, or DMA controller.
In the IBM System/360 storage architecture, the Volume Table of Contents (VTOC), is a data structure that provides a way of locating the data sets that reside on a particular DASD volume. With the exception of the IBM Z compatible disk layout in Linux on Z, it is the functional equivalent of the MS/PC DOS File Allocation Table (FAT), the NTFS Master File Table (MFT), and an inode table in a file system for a Unix-like system. The VTOC is not used to contain any IPLTEXT and does not have any role in the IPL process, therefore does not have any data used by or functionally equivalent to the MBR. It lists the names of each data set on the volume as well as size, location, and permissions. Additionally, it contains an entry for every area of contiguous free space on the volume. The third record on the first track of the first cylinder of any DASD volume is known as the volume label and must contain a pointer to the location of the VTOC. The location of the VTOC may be specified when the volume is initialized. For performance reasons it may be located as close to the center of the volume as possible, since it is referenced frequently. A VTOC is added to a DASD volume when it is initialized using the Device Support Facilities program, ICKDSF, in current systems.
In 1953, IBM recognized the immediate application for what it termed a "Random Access File" having high capacity and rapid random access at a relatively low cost. After considering technologies such as wire matrices, rod arrays, drums, drum arrays, etc., the engineers at IBM's San Jose California laboratory invented the hard disk drive. The disk drive created a new level in the computer data hierarchy, then termed Random Access Storage but today known as secondary storage, less expensive and slower than main memory but faster and more expensive than tape drives.
Magnetic-tape data storage is a system for storing digital information on magnetic tape using digital recording.
In computer disk storage, a sector is a subdivision of a track on a magnetic disk or optical disc. Each sector stores a fixed amount of user-accessible data, traditionally 512 bytes for hard disk drives (HDDs) and 2048 bytes for CD-ROMs and DVD-ROMs. Newer HDDs use 4096-byte (4 KiB) sectors, which are known as the Advanced Format (AF).
Count key data (CKD) is a direct-access storage device (DASD) data recording format introduced in 1964, by IBM with its IBM System/360 and still being emulated on IBM mainframes. It is a self-defining format with each data record represented by a Count Area that identifies the record and provides the number of bytes in an optional Key Area and an optional Data Area. This is in contrast to devices using fixed sector size or a separate format track.
In IBM mainframe operating systems, Execute Channel Program (EXCP) is a macro generating a system call, implemented as a Supervisor Call instruction, for low-level device access, where the programmer is responsible for providing a channel program—a list of device-specific commands (CCWs)—to be executed by I/O channels, control units and devices. EXCP for OS/360 and successors is more specifically described in the OS System Programmer's Guide.; EXCP for DOS/360 and successors is more specifically described in DOS Supervisor and I/O Macros. This article mostly reflects OS/360 through z/OS; some details are different for TOS/360 and DOS/360 through z/VSE.
Fixed-block architecture (FBA) is an IBM term for the hard disk drive (HDD) layout in which each addressable block on the disk has the same size, utilizing 4 byte block numbers and a new set of command codes. FBA as a term was created and used by IBM for its 3310 and 3370 HDDs beginning in 1979 to distinguish such drives as IBM transitioned away from their variable record size format used on IBM's mainframe hard disk drives beginning in 1964 with its System/360.
Basic Direct Access Method, or BDAM is an access method for IBM's OS/360 and successors computer operating systems on System/360 and later mainframes. BDAM "consists of routines used in retrieving data from, and storing data onto, direct access devices." BDAM is available on OS/360, OS/VS2, MVS, z/OS, and related high-end operating systems.
The IBM System/360 Model 20 is the smallest member of the IBM System/360 family announced in November 1964. The Model 20 supports only a subset of the System/360 instruction set, with binary numbers limited to 16 bits and no floating point. In later years it would have been classified as a 16-bit minicomputer rather than a mainframe, but the term "minicomputer" was not current, and in any case IBM wanted to emphasize the compatibility of the Model 20 rather than its differences from the rest of the System/360 line. It does, however, have the full System/360 decimal instruction set, that allows for addition, subtraction, product, and dividend of up to 31 decimal digits.
Beginning with its 1964 System/360 announcement, IBM's mainframes initially accessed CKD subsystems via a channel connected to separate Storage Control Units (SCUs) with attached Direct Access Storage Devices (DASD), typically a hard disk drive. This practice continued in IBM's larger mainframes thru System/370; however low end systems generally used lower cost integrated attachments where the function of the SCU was combined with that of the channel, typically called an Integrated File Adapter.
In addition to the drums used as main memory by IBM, e.g., IBM 305, IBM 650, IBM offered drum devices as secondary storage for the 700/7000 series and System/360 series of computers.
A track is a path on a recording medium. There are some variations in nomenclature; for some media a track is a logical path and for others it is based on the geometry of the medium. The term is not used for punched cards.
