6AK5

Last updated
6AK5
6AK5 vacuum tubes.JPG
6AK5 vacuum tubes, from left to right: EF95 by Phillips, 6AK5 by NEC, 6Zh1P Russia (Novosibirsk), 6Zh1P Russia (Svetlana)
ClassificationPentode
ServiceVHF RF amplifier
Height1+34 in (44 mm)
Diameter34 in (19 mm)
Cathode
Cathode typeUnipotential
Heater voltage6.3 V
Heater current175 mA
Anode
Max dissipation Watts1.7 W
Max voltage180 V
Socket connections
B7G

The 6AK5 vacuum tube is a miniature 7-pin sharp-cutoff pentode used as RF or IF amplifier especially in high-frequency wide-band applications at frequencies up to 400 MHz.

Contents

It was developed by Bell Labs / Western Electric and used extensively as an I.F. amplifier in World War II radar systems. The tube is notable for its extremely fine grid, and extremely close control grid to cathode spacing, yielding excellent high-frequency performance.

It is also known as EF95 under its Mullard–Phillips designation and was produced in the former Soviet Union as type 6Zh1P (Russian: 6Ж1П) under the Russian designation system.

A version of this tube with extended ratings was designated 6AK5W and 6Zh1P-EV (Russian: 6Ж1П-ЕВ) respectively.

Even though primarily intended for VHF amplification, the tube has found some use in audio applications as a microphone preamplifier, for instance in the LOMO 19A9 microphone, headphone amplifiers such as the Little Dot MKIII, and in guitar effects stompboxes, such as Metasonix TM-7 Scrotum Smasher.[ citation needed ]

The 6AK5 was used in some types of radiosonde (weather balloon payloads), in the 1960s and 70s. Because of the non-recoverable nature of the equipment, the single 6AK5 was soldered directly to the printed circuit board and served as the only active device in the circuit, performing the function of a low frequency modulation oscillator and the high frequency carrier oscillator and output stage.

See also

Related Research Articles

An electronic oscillator is an electronic circuit that produces a periodic, oscillating or alternating current (AC) signal, usually a sine wave, square wave or a triangle wave, powered by a direct current (DC) source. Oscillators are found in many electronic devices, such as radio receivers, television sets, radio and television broadcast transmitters, computers, computer peripherals, cellphones, radar, and many other devices.

<span class="mw-page-title-main">Amplifier</span> Electronic device/component that increases the strength of a signal

An amplifier, electronic amplifier or (informally) amp is an electronic device that can increase the magnitude of a signal. It is a two-port electronic circuit that uses electric power from a power supply to increase the amplitude of a signal applied to its input terminals, producing a proportionally greater amplitude signal at its output. The amount of amplification provided by an amplifier is measured by its gain: the ratio of output voltage, current, or power to input. An amplifier is defined as a circuit that has a power gain greater than one.

<span class="mw-page-title-main">Superheterodyne receiver</span> Type of radio receiver

A superheterodyne receiver, often shortened to superhet, is a type of radio receiver that uses frequency mixing to convert a received signal to a fixed intermediate frequency (IF) which can be more conveniently processed than the original carrier frequency. It was invented by French radio engineer and radio manufacturer Lucien Lévy. Virtually all modern radio receivers use the superheterodyne principle.

<span class="mw-page-title-main">Triode</span> Single-grid amplifying vacuum tube having three active electrodes

A triode is an electronic amplifying vacuum tube consisting of three electrodes inside an evacuated glass envelope: a heated filament or cathode, a grid, and a plate (anode). Developed from Lee De Forest's 1906 Audion, a partial vacuum tube that added a grid electrode to the thermionic diode, the triode was the first practical electronic amplifier and the ancestor of other types of vacuum tubes such as the tetrode and pentode. Its invention helped make amplified radio technology and long-distance telephony possible. Triodes were widely used in consumer electronics devices such as radios and televisions until the 1970s, when transistors replaced them. Today, their main remaining use is in high-power RF amplifiers in radio transmitters and industrial RF heating devices. In recent years there has been a resurgence in demand for low power triodes due to renewed interest in tube-type audio systems by audiophiles who prefer the sound of tube-based electronics.

<span class="mw-page-title-main">Vacuum tube</span> Device that controls current between electrodes

A vacuum tube, electron tube, valve, or tube, is a device that controls electric current flow in a high vacuum between electrodes to which an electric potential difference has been applied.

A tetrode is a vacuum tube having four active electrodes. The four electrodes in order from the centre are: a thermionic cathode, first and second grids, and a plate. There are several varieties of tetrodes, the most common being the screen-grid tube and the beam tetrode. In screen-grid tubes and beam tetrodes, the first grid is the control grid and the second grid is the screen grid. In other tetrodes one of the grids is a control grid, while the other may have a variety of functions.

<span class="mw-page-title-main">Valve amplifier</span> Type of electronic amplifier

A valve amplifier or tube amplifier is a type of electronic amplifier that uses vacuum tubes to increase the amplitude or power of a signal. Low to medium power valve amplifiers for frequencies below the microwaves were largely replaced by solid state amplifiers in the 1960s and 1970s. Valve amplifiers can be used for applications such as guitar amplifiers, satellite transponders such as DirecTV and GPS, high quality stereo amplifiers, military applications and very high power radio and UHF television transmitters.

The Hartley oscillator is an electronic oscillator circuit in which the oscillation frequency is determined by a tuned circuit consisting of capacitors and inductors, that is, an LC oscillator. The circuit was invented in 1915 by American engineer Ralph Hartley. The distinguishing feature of the Hartley oscillator is that the tuned circuit consists of a single capacitor in parallel with two inductors in series, and the feedback signal needed for oscillation is taken from the center connection of the two inductors.

<span class="mw-page-title-main">Regenerative circuit</span> Electronic circuit using positive feedback

A regenerative circuit is an amplifier circuit that employs positive feedback. Some of the output of the amplifying device is applied back to its input to add to the input signal, increasing the amplification. One example is the Schmitt trigger, but the most common use of the term is in RF amplifiers, and especially regenerative receivers, to greatly increase the gain of a single amplifier stage.

<span class="mw-page-title-main">Traveling-wave tube</span> Microwave signal amplifier

A traveling-wave tube or traveling-wave tube amplifier is a specialized vacuum tube that is used in electronics to amplify radio frequency (RF) signals in the microwave range. It was invented by Andrei Haeff around 1933 as a graduate student at Caltech, and its present form was invented by Rudolf Kompfner in 1942-43. The TWT belongs to a category of "linear beam" tubes, such as the klystron, in which the radio wave is amplified by absorbing power from a beam of electrons as it passes down the tube. Although there are various types of TWT, two major categories are:

<span class="mw-page-title-main">12AX7</span> Miniature high-gain dual triode vacuum tube

12AX7 is a miniature dual-triode 6AV6 vacuum tube with high voltage gain. Developed around 1946 by RCA engineers in Camden, New Jersey, under developmental number A-4522, it was released for public sale under the 12AX7 identifier on September 15, 1947.

The Clapp oscillator or Gouriet oscillator is an LC electronic oscillator that uses a particular combination of an inductor and three capacitors to set the oscillator's frequency. LC oscillators use a transistor and a positive feedback network. The oscillator has good frequency stability.

<span class="mw-page-title-main">Wien bridge oscillator</span> Electric circuit that generates sine waves

A Wien bridge oscillator is a type of electronic oscillator that generates sine waves. It can generate a large range of frequencies. The oscillator is based on a bridge circuit originally developed by Max Wien in 1891 for the measurement of impedances. The bridge comprises four resistors and two capacitors. The oscillator can also be viewed as a positive gain amplifier combined with a bandpass filter that provides positive feedback. Automatic gain control, intentional non-linearity and incidental non-linearity limit the output amplitude in various implementations of the oscillator.

<span class="mw-page-title-main">12AU7</span> Miniature medium-gain dual-triode vacuum tube

The 12AU7 and its variants are miniature nine-pin medium-gain dual-triode vacuum tubes. It belongs to a large family of dual-triode vacuum tubes which share the same pinout. 12AU7 is also known in Europe under its Mullard–Philips tube designation ECC82. There are many equivalent tubes with different names, some identical, some designed for ruggedness, long life, or other characteristics; examples are the US military 5814A and the European special-quality ECC82 and E182CC.

Vacuum tubes produced in the former Soviet Union and in present-day Russia carry their own unique designations. Some confusion has been created in "translating" these designations, as they use Cyrillic rather than Latin characters.

<span class="mw-page-title-main">Carbon microphone</span> Microphone design

The carbon microphone, also known as carbon button microphone, button microphone, or carbon transmitter, is a type of microphone, a transducer that converts sound to an electrical audio signal. It consists of two metal plates separated by granules of carbon. One plate is very thin and faces toward the speaking person, acting as a diaphragm. Sound waves striking the diaphragm cause it to vibrate, exerting a varying pressure on the granules, which in turn changes the electrical resistance between the plates. Higher pressure lowers the resistance as the granules are pushed closer together. A steady direct current is passed between the plates through the granules. The varying resistance results in a modulation of the current, creating a varying electric current that reproduces the varying pressure of the sound wave. In telephony, this undulating current is directly passed through the telephone wires to the central office. In public address systems it is amplified by an audio amplifier. The frequency response of most carbon microphones, however, is limited to a narrow range, and the device produces significant electrical noise.

<span class="mw-page-title-main">Valve RF amplifier</span> Device for electrically amplifying the power of an electrical radio frequency signal

A valve RF amplifier or tube amplifier (U.S.) is a device for electrically amplifying the power of an electrical radio frequency signal.

A Virtual Valve Amplifier (VVA) is software algorithm designed and sold by Diamond Cut Productions, Inc. for simulating the sound of various valve amplifier designs. It can be found within their DC8 and Forensics8 software programs.

<span class="mw-page-title-main">Acorn tube</span> Family of VHF/UHF vacuum tubes

An acorn tube, or acorn valve, refers to any member of a family of VHF/UHF vacuum tubes starting just before World War II. They were named after their resemblance to the acorn, specifically due to the glass cap at one end of the tube that looked similar to the cap on an acorn. The acorn tubes found widespread use in radios and radar systems.

References