A-series light bulb

Last updated
An A-series light bulb Gluehlampe 01 KMJ.png
An A-series light bulb

The A-series light bulb is the "classic" glass light bulb shape that has been the most commonly used type for general lighting service (GLS) applications since the early 20th century. It has a pear-like shape and is typically fitted to either an Edison screw or a bayonet cap base. The number that follows the "A" designation indicates the nominal major diameter of the bulb, either in one-eighth inch units in North America [1] [2] [3] or in millimeters in the rest of the world. [4] [5] [6]

Contents

An A60 (A19) LED light bulb with an E27 Edison screw base Led-lampa.jpg
An A60 (A19) LED light bulb with an E27 Edison screw base

Although A-shape bulbs historically used incandescent lighting technology, A-shaped compact fluorescent (CFL) and LED lamps are also commonly available.

Physical outline

The most commonly used A-series light bulb type is an A60 bulb [7] (or its inch-based equivalent, the A19 bulb [2] [4] ), which is 60 mm (198 in or 2+38 in) wide at its widest point [3] and approximately 110 mm (4+38 in) in length. [8] Other sizes with a data sheet in IEC 60064 are A50, A55, A67, A68, A71, A75, and A80. Another common A-series light bulb type is the A15 bulb which is commonly used in the US for appliances and ceiling fans. The A15 bulb is 158 in (1+78 in; 48 mm) wide at its widest point and 3.39 inches tall.

Socket type

In countries with a mains supply voltage of 100120  volts (e.g., Canada, Taiwan, US), A19/A60 light bulbs usually come with an E26 type Edison screw base (i.e. 26 millimeters in diameter). In the UK, Ireland and many Commonwealth countries, they usually come with a B22 type bayonet cap base. In continental Europe and most other countries with a 220240 volt supply, they usually come with an E27 type base.[ citation needed ]

Specifications

IEC/TR 60887:2010 [4] defines the A bulb shape as:

A bulb shape having a spherical end section that is joined to the neck by a radius that (a) has a centre outside the bulb, (b) has a magnitude greater than the radius of the spherical section, (c) and is tangent to both the neck and the curve of the spherical end section.

The same standard also defines in addition to the A shape also bulged (B), conical (C), elliptical (E), flame (F), Globular (G), (K), mushroom (M), (P), reflector (R), straight-sided (S) and tubular (T) bulb shapes, as well as several modifier letters and special shapes. Very similar to the A shape are the P shape ("A bulb having a spherical end section, and a conical mid section, the sides of which are tangent to the curve of the spherical section"), and its PS variant ("Tubular neck section below the bulb and above the approximate reference line").

Philips L Prize bulbs count as A19 under Energy Star requirements. Philips LED bulbs.jpg
Philips L Prize bulbs count as A19 under Energy Star requirements.

ANSI C79.1-2002, IS 14897:2000, [5] and JIS C 7710:1988 [9] define the "A shape" as "a bulb shape having a spherical end section that is joined to the neck by a radius", where the radius is greater than that of the sphere, corresponds to an osculating circle outside the light bulb, and is tangent to both the neck and the sphere.

The USA Energy Star certification requires omnidirectional light bulbs to fit the overall dimensions of the corresponding ANSI bulb type and a minimum Luminosity/Watt performance level. [10] :14.1

Related Research Articles

<span class="mw-page-title-main">Electric light</span> Device for producing light from electricity

An electric light, lamp, or light bulb is an electrical component that produces light. It is the most common form of artificial lighting. Lamps usually have a base made of ceramic, metal, glass, or plastic, which secures the lamp in the socket of a light fixture, which is often called a "lamp" as well. The electrical connection to the socket may be made with a screw-thread base, two metal pins, two metal caps or a bayonet mount.

<span class="mw-page-title-main">Sphere</span> Set of points equidistant from a center

A sphere is a geometrical object that is a three-dimensional analogue to a two-dimensional circle. Formally, a sphere is the set of points that are all at the same distance r from a given point in three-dimensional space. That given point is the center of the sphere, and r is the sphere's radius. The earliest known mentions of spheres appear in the work of the ancient Greek mathematicians.

<span class="mw-page-title-main">Incandescent light bulb</span> Electric light bulb with a resistively heated wire filament

An incandescent light bulb, incandescent lamp or incandescent light globe is an electric light with a filament that is heated until it glows. The filament is enclosed in a glass bulb that is either evacuated or filled with inert gas to protect the filament from oxidation. Electric current is supplied to the filament by terminals or wires embedded in the glass. A bulb socket provides mechanical support and electrical connections.

<span class="mw-page-title-main">Halogen lamp</span> Incandescent lamp variety

A halogen lamp is an incandescent lamp consisting of a tungsten filament sealed in a compact transparent envelope that is filled with a mixture of an inert gas and a small amount of a halogen, such as iodine or bromine. The combination of the halogen gas and the tungsten filament produces a halogen-cycle chemical reaction, which redeposits evaporated tungsten on the filament, increasing its life and maintaining the clarity of the envelope. This allows the filament to operate at a higher temperature than a standard incandescent lamp of similar power and operating life; this also produces light with higher luminous efficacy and color temperature. The small size of halogen lamps permits their use in compact optical systems for projectors and illumination. The small glass envelope may be enclosed in a much larger outer glass bulb, which has a lower temperature, protects the inner bulb from contamination, and makes the bulb mechanically more similar to a conventional lamp.

<span class="mw-page-title-main">Pressure vessel</span> Vessel for pressurised gases or liquids

A pressure vessel is a container designed to hold gases or liquids at a pressure substantially different from the ambient pressure.

<span class="mw-page-title-main">Nose cone design</span> Geometry and construction of the foremost tip of airplanes, spacecraft and projectiles

Given the problem of the aerodynamic design of the nose cone section of any vehicle or body meant to travel through a compressible fluid medium, an important problem is the determination of the nose cone geometrical shape for optimum performance. For many applications, such a task requires the definition of a solid of revolution shape that experiences minimal resistance to rapid motion through such a fluid medium.

<span class="mw-page-title-main">Handrail</span> Rail that is designed to be grasped by the hand so as to provide stability or support

A handrail is a rail that is designed to be grasped by the hand so as to provide safety or support. In Britain, handrails are referred to as banisters. Handrails are commonly used while ascending or descending stairways and escalators in order to prevent injurious falls, and to provide bodily support in bathrooms or similar areas. Handrails are typically supported by balusters or attached to walls.

<span class="mw-page-title-main">Electronic symbol</span> Pictogram used to represent various electrical and electronic devices or functions

An electronic symbol is a pictogram used to represent various electrical and electronic devices or functions, such as wires, batteries, resistors, and transistors, in a schematic diagram of an electrical or electronic circuit. These symbols are largely standardized internationally today, but may vary from country to country, or engineering discipline, based on traditional conventions.

<span class="mw-page-title-main">Parabolic aluminized reflector</span> Type of electric lamp

A parabolic aluminized reflector lamp is a type of electric lamp that is widely used in commercial, residential, and transportation illumination. It produces a highly directional beam. Usage includes theatrical lighting, locomotive headlamps, aircraft landing lights, and residential and commercial recessed lights.

<span class="mw-page-title-main">Fresnel lantern</span> Lantern using a Fresnel lens

A Fresnel lantern is a common lantern used in theatre that employs a Fresnel lens to wash light over an area of the stage. The lens produces a wider, soft-edged beam than a spotlight or key light, and is commonly used for back light and top light.

<span class="mw-page-title-main">Bayonet mount</span> Fastening mechanism

A bayonet mount or bayonet connector is a fastening mechanism consisting of a cylindrical male side with one or more radial pins, and a female receptor with matching L-shaped slot(s) and with spring(s) to keep the two parts locked together. The slots are shaped like a capital letter L with serif ; the pin slides into the vertical arm of the L, rotates across the horizontal arm, then is pushed slightly upwards into the short vertical "serif" by the spring; the connector is no longer free to rotate unless pushed down against the spring until the pin is out of the "serif".

<span class="mw-page-title-main">Edison screw</span> Lightbulb socket standard (E5-E40)

Edison screw (ES) is a standard lightbulb socket for electric light bulbs. It was developed by Thomas Edison (1847–1931), patented in 1881, and was licensed in 1909 under General Electric's Mazda trademark. The bulbs have right-hand threaded metal bases (caps) which screw into matching threaded sockets. For bulbs powered by AC current, the thread is generally connected to neutral and the contact on the bottom tip of the base is connected to the "live" phase.

<span class="mw-page-title-main">Multifaceted reflector</span> Light bulb

A multifaceted reflector light bulb is a reflector housing format for halogen as well as some LED and fluorescent lamps. MR lamps were originally designed for use in slide projectors, but see use in residential lighting and retail lighting as well. They are suited to applications that require directional lighting such as track lighting, recessed ceiling lights, desk lamps, pendant fixtures, landscape lighting, retail display lighting, and bicycle headlights. MR lamps are designated by symbols such as MR16 where the diameter is represented by numerals indicating units of eighths of an inch. Common sizes for general lighting are MR16 and MR11, with MR20 and MR8 used in specialty applications. Many run on low voltage rather than mains voltage alternating current so require a power supply.

<span class="mw-page-title-main">Bi-pin lamp base</span> Type of lamp/lightbulb fitting/connector

A bipin or bi-pin is a type of lamp fitting. They are included in the IEC standard "IEC 60061 Lamp caps and holders together with gauges for the control of interchangeability and safety". They are used on many small incandescent light bulbs, and for starters on some types of fluorescent lights.

<span class="mw-page-title-main">Holiday lighting technology</span> Decorative lighting for festivities

Holiday lighting technology has been subject to considerable development and variation since the replacement of candles by electric lights. While originally used during the Christmas holidays as Christmas lights, modern electric light arrays have become popular around the world in many cultures and are used both during religious festivals and for other purposes unconnected to any festivities.

Standard battery nomenclature describes portable dry cell batteries that have physical dimensions and electrical characteristics interchangeable between manufacturers. The long history of disposable dry cells means that many manufacturer-specific and national standards were used to designate sizes, long before international standards were reached. Technical standards for battery sizes and types are set by standards organizations such as International Electrotechnical Commission (IEC) and American National Standards Institute (ANSI). Popular sizes are still referred to by old standard or manufacturer designations, and some non-systematic designations have been included in current international standards due to wide use.

<span class="mw-page-title-main">Fluorescent-lamp formats</span> Types of lamp

Since their introduction as a commercial product in 1939, many different types of fluorescent lamp have been introduced. Systematic nomenclature identifies mass-market lamps as to overall shape, power rating, length, color, and other electrical and illuminating characteristics.

A lightbulb socket, lightbulb holder,light socket, lamp socket or lamp holder is a device which mechanically supports and provides electrical connections for a compatible electric lamp base. Sockets allow lamps to be safely and conveniently replaced (re-lamping). There are many different standards for lampholders, including early de facto standards and later standards created by various standards bodies. Many of the later standards conform to a general coding system in which a socket type is designated by a letter or abbreviation followed by a number.

<span class="mw-page-title-main">Recessed light</span>

A recessed light or downlight is a light fixture that is installed into a hollow opening in a ceiling. When installed it appears to have light shining from a hole in the ceiling, concentrating the light in a downward direction as a broad floodlight or narrow spotlight.

References

  1. "Lamp Size and Comparison Features" (PDF). WW Grainger Inc. Lamp size (maximum lamp diameter) is expressed by a number representing eighths of an inch.
  2. 1 2 "LED University: Light Bulb Shapes and Sizes Explained". EagleLight. 'A' type bulb shapes are standard house hold light bulbs. The number after the bulb shape is the number of eighths of an inch in diameter. For non-imperial measured bulbs the number following the bulb shape is the number of centimeters [sic] at the widest point of the bulb. Standard bulb sizes include A19 in the United States and A60 for a slightly smaller metric measured bulb.
  3. 1 2 "Light Bulb Reference Guide". Superior Lighting. The letter indicates the shape of the bulb and the number relates to the diameter of the bulb in eighths of an inch. The most commonly used household bulb is the A-19.
  4. 1 2 3 Glass bulb designation system for lamps. Technical report IEC/TR 60887:2010, Edition 3.0, International Electrotechnical Commission, 2010-06.
  5. 1 2 "IS 14897 (2000): Glass Bulb Designation System for Lamps - Guide" . Retrieved 21 March 2017. A bulb shape having a spherical and [sic; end?] section that is joined to the neck by a radius [...] A60: An "A" shape bulb with a nominal major diameter of 60 mm.
  6. "LED Start GLS: 40, 60, 75 & 90w equivalents" (PDF). GE Lightling. Archived from the original (PDF) on 2017-03-21. Retrieved 2017-03-22.
  7. A19 Bulb Vs E26 Bulb: What’s the Difference? "A19 Bulb Vs E26", KRM Light+
  8. "Light fixtures and light bulb sizes". www.tuxgraphics.org. Retrieved 28 February 2017.
  9. "JIS C 7710:1988 電球類ガラス管球の形式の表し方" (in Japanese). Retrieved 2017-03-21.
  10. "ENERGY STAR Eligibility Criteria Version 2.0, Rev. Oct-2016" (PDF). Retrieved 2017-03-21. Lamp shall comply with ANSI minimum overall length (min OAL), maximum overall length (MOL) and maximum lamp diameter values, where they exist