System for high-speed testing of electronic devices
Automatic test system switchingtest equipment allows for high-speed testing of a device or devices in a test situation, where strict sequences and combinations of switching must be observed. By automating the process in this way, the possibility of test errors and inaccuracies is minimized, and only systematic errors would generally be encountered due to such as an incorrect programmed test condition. This eliminates error due to human factors and allows application of a standard test sequence repetitively. The design of a test system’s switching configuration is governed by the test specification, which is derived from the functional tests to be performed.
A typical test system would involve the connection of input and outputs of the device under test to the test equipment, which is usually controlled by an electronic program generated by a computer or a programmable logic controller.
Switch Relays
The simplest definition of a switch is “a device that opens or closes a circuit.” [1]
A relay is an electronically operated switch. Three relay types are commonly used in automated test system switching:
Electromechanical relays are the most-often-used type because they have the largest signal range capability of the three. They also have the slowest actuation time and the shortest useful life. Electromechanical relays are ideal for high-voltage, high-current, and RF applications. A latching feature makes the latching relay type very appropriate for low-voltage applications where contact potential can interfere with the measurement.
Reed relays have actuation times of 0.5 ms to 2 ms and long life. By design, reed relays can only handle a portion of the signal range that electromechanical relays can offer. But they do provide a useful trade-off between increasing speed and maintaining signal integrity.
Solid-state relays can switch the fastest and have essentially infinite life. However, they can only handle small signal ranges and suffer from high on-resistance and high offset currents in the nanoamp range compared to picoamps of offset current for the other two types.[2]
has no voltage drop across the switch during its ON state
has no voltage limit during its OFF state
has zero rise time and fall time during state changes
switches only once without “bouncing” between on and off positions
It’s important to recognize, however, that real-life switches are not ideal, so when calculating the overall system accuracy, the effects of the switch itself and all the switching hardware in the system must be factored in.
As a signal travels from its source to its destination, it can encounter various forms of interference and sources of error, so whenever a signal passes through a connecting cable or switch point, it may be degraded. For example, in low current and high resistance applications, unshielded cabling can introduce leakage currents that will degrade measurement accuracy.[3] Unshielded cable can result in noisy readings for low current and high resistance applications, especially if the cabling runs adjacent to equipment generating electromagnetic interference.[4]
Switch Relay Terminology
Figure 1
Three terms are used to describe the configuration of a relay: pole, throw, and form.[5]
Pole refers to the number of common terminals within a given switch. Throw refers to the number of positions in which the switch may be placed to create a signal path or connection. Figure lA illustrates a single-pole, single-throw normally open switch (SPST NO). Figure 1B shows a single-pole, double-throw (SPDT) switch. One terminal is normally-open (NO) and the other is normally-closed (NC). Depending on the state of the switch, one or the other position is connected to the common terminal (COM). One signal path is broken before the other is connected, so this is referred to as a break-before-make configuration.[6]
Figure 2 Scanner - a one out n selector switch
When more than one common terminal is used, the number of poles increases. Figure 1C shows a double-pole, single-throw (DPST) switch. Both poles are actuated simultaneously when the relay is energized. In this case, both poles are either always closed or always open. Figure 1D illustrates a double-pole, double throw (DPDT) switch.
Contact form, or simply form, is the term relay manufacturers use to describe a relay's contact configuration. "Form A” refers to a single-pole, normally open switch. "Form B" indicates a single-pole, normally closed switch, and "Form C" indicates a single-pole, double-throw switch. Virtually any contact configuration can be described using this format.
Switch System Topology
A variety of switching configurations are commercially available for test system development:
Scanner
The scanner (Figure 2) is used to connect multiple inputs to a single output in sequential order. Only one relay is closed at any one time. In its most basic form, relay closure proceeds from the first channel to the last, but some scanner systems allow skipping channels. Typical scanner switching applications include component burn-in testing, monitoring time and temperature drift in circuits, and taking data on system variables like temperature, pressure, flow, etc.
Multiplexer
Like a scan configuration, multiplex switching can be used to connect one instrument to multiple devices (1:N) or multiple instruments to a single device (N:1), but it offers much more flexibility than the scanner configuration because it permits multiple simultaneous connections and both sequential and non-sequential switch closures. Typical applications of multiplex switching include capacitor leakage, insulation resistance, and contact resistance test systems for multiple devices.
Matrix
The matrix switch configuration is the most versatile because it can connect multiple inputs to multiple outputs. A matrix is useful when connections must be made between several signal sources and a multipin device, such as an integrated circuit or resistor network.
Using a matrix switch card allows connecting any input to any output by closing the switch at the intersection (crosspoint) of a given row and column. The most common terminology to describe the matrix size is M rows by N columns (MxN). Matrix switch cards generally have two or three poles per crosspoint. As shown in Figure 3, a 5VDC source can be connected to any two terminals of the device under test (DUT). A function generator supplies pulses between another two terminals. Operation of the DUT can be verified by connecting an oscilloscope between two other terminals. The DUT pin connections can easily be programmed, so this system can be used to test a variety of components.
Figure 3. A 6x8 one-pole matrix
Some performance tradeoffs are typically necessary when choosing a matrix card for use with mixed signals. For example, if both high frequency and low current signals must be switched, take extra care when reviewing the specifications of the card. The card chosen must have wide bandwidth, as well as good isolation and low offset current. A single matrix card may not satisfy both requirements completely, so the system builder must decide which switched signal is more critical.
In a system with multiple cards, card types should not be mixed if their outputs are connected together. For example, a general-purpose matrix card with its output connected in parallel with a low current matrix card will degrade the performance of the low current card.
Expanding a Matrix
A large test system may require more rows and/or columns than a single switch card can accommodate, but it’s possible to expand a matrix by joining the rows and/or columns of several cards together. Depending on the switch card and mainframe selected, the rows of the cards may be connected together through the backplane of the mainframe or the rows may be wired externally.
Isolated switching
Figure 4. Single isolated switch
The isolated, or independent, switch configuration consists of individual relays, often with multiple poles, with no connections between relays. Isolated relays are commonly used in power and control applications to open and close different parts of a circuit that are at substantially different voltage levels. Applications for isolated relays include controlling power supplies, turning on motors and annunciator lamps, and actuating pneumatic or hydraulic valves. Figure 4 illustrates a single isolated relay or actuator, in which a single-pole normally open relay is controlling the connection of the voltage source to the lamp. This relay connects one input to one output. An isolated relay can have more than one pole and can have normally closed contacts as well as normally open contacts.
Figure 5. Isolated relays on a switch card
Isolated relays are not connected to any other circuit, so the addition of some external wiring makes them suitable for building very flexible and unique combinations of input/output configurations.
Given that the relays are isolated from each other, the terminals of each channel on the switch card are independent from the terminals of the other channels. As shown in Figure 5, each isolated Form A relay has two terminals. Two-pole isolated relays would have four terminals (two inputs and two outputs). A Form C isolated relay would have three terminals.
Cold vs. Hot Switching
The term cold switching indicates that a switch is activated with no signal applied. Therefore, no current will flow when the switch is closed, and no current will be interrupted when the switch is opened. In contrast, in hot switching, voltage is present and current will flow immediately once the contacts close. When the switch is opened, this current will be interrupted and can cause arcing.[7]
Cold switching allows power to be applied to the device under test in a controlled manner. Its primary advantage is a longer switch life than with hot switching (up to a thousand times more cycles than with hot switching). Cold switching also eliminates arcing at the relay contacts and any radio frequency interference that might be caused by arcing. Hot switching might be necessary if close control must be exercised in the period between the application of power and the making of the measurement. For example, hot switching is typically used where digital logic is involved, because devices might change state if power is interrupted even for a moment.
With relatively large relays, hot switching may be necessary to ensure good contact closure. The connection may not be reliable without the “wetting” action of the current through the contacts.[8]
Related Research Articles
An amplifier, electronic amplifier or (informally) amp is an electronic device that can increase the power of a signal. It is a two-port electronic circuit that uses electric power from a power supply to increase the amplitude of a signal applied to its input terminals, producing a proportionally greater amplitude signal at its output. The amount of amplification provided by an amplifier is measured by its gain: the ratio of output voltage, current, or power to input. An amplifier is a circuit that has a power gain greater than one.
A programmable logic controller (PLC) or programmable controller is an industrial computer that has been ruggedized and adapted for the control of manufacturing processes, such as assembly lines, machines, robotic devices, or any activity that requires high reliability, ease of programming, and process fault diagnosis. Dick Morley is considered as the father of PLC as he had invented the first PLC, the Modicon 084, for General Motors in 1968.
A relay is an electrically operated switch. It consists of a set of input terminals for a single or multiple control signals, and a set of operating contact terminals. The switch may have any number of contacts in multiple contact forms, such as make contacts, break contacts, or combinations thereof.
In electrical engineering, a switch is an electrical component that can disconnect or connect the conducting path in an electrical circuit, interrupting the electric current or diverting it from one conductor to another. The most common type of switch is an electromechanical device consisting of one or more sets of movable electrical contacts connected to external circuits. When a pair of contacts is touching current can pass between them, while when the contacts are separated no current can flow.
Ladder logic was originally a written method to document the design and construction of relay racks as used in manufacturing and process control. Each device in the relay rack would be represented by a symbol on the ladder diagram with connections between those devices shown. In addition, other items external to the relay rack such as pumps, heaters, and so forth would also be shown on the ladder diagram.
In electronics, a multi-transistor configuration called the Darlington configuration is a circuit consisting of two bipolar transistors with the emitter of one transistor connected to the base of the other, such that the current amplified by the first transistor is amplified further by the second one. The collectors of both transistors are connected together. This configuration has a much higher current gain than each transistor taken separately. It acts like and is often packaged as a single transistor. It was invented in 1953 by Sidney Darlington.
A power inverter, inverter or invertor is a power electronic device or circuitry that changes direct current (DC) to alternating current (AC). The resulting AC frequency obtained depends on the particular device employed. Inverters do the opposite of rectifiers which were originally large electromechanical devices converting AC to DC.
The analogueswitch, also called the bilateral switch, is an electronic component that behaves in a similar way to a relay, but has no moving parts. The switching element is normally a pair of MOSFET transistors, one an N-channel device, the other a P-channel device. The device can conduct analog or digital signals in either direction when on and isolates the switched terminals when off. Analogue switches are usually manufactured as integrated circuits in packages containing multiple switches. These include the 4016 and 4066 from the 4000 series.
The reed switch is an electromechanical switch operated by an applied magnetic field. It was invented in 1922 by professor Valentin Kovalenkov at Leningrad Electrotechnical University, and later evolved at Bell Telephone Laboratories in 1936 by Walter B. Ellwood into the reed relay. In its simplest and most common form, it consists of a pair of ferromagnetic flexible metal contacts in a hermetically sealed glass envelope. The contacts are usually normally open, closing when a magnetic field is present, or they may be normally closed and open when a magnetic field is applied. The switch may be actuated by an electromagnetic coil, making a reed relay, or by bringing a permanent magnet near it. When the magnetic field is removed, the contacts in the reed switch return to their original position. The "reed" is the metal part inside the reed switch envelope that is relatively thin and wide to make it flexible. It somewhat resembles part of some reed plants. The term "reed" may also include the external wire lead as well as the internal part.
A remote terminal unit(RTU) is a microprocessor-controlled electronic device that interfaces objects in the physical world to a distributed control system or SCADA system by transmitting telemetry data to a master system, and by using messages from the master supervisory system to control connected objects. Other terms that may be used for RTU are remote telemetry unit and remote telecontrol unit.
An opto-isolator is an electronic component that transfers electrical signals between two isolated circuits by using light. Opto-isolators prevent high voltages from affecting the system receiving the signal. Commercially available opto-isolators withstand input-to-output voltages up to 10 kV and voltage transients with speeds up to 25 kV/μs.
In electrical control engineering, a stepping switch or stepping relay, also known as a uniselector, is an electromechanical device that switches an input signal path to one of several possible output paths, directed by a train of electrical pulses.
Power electronics is the application of electronics to the control and conversion of electric power.
In electrical signalling an analog current loop is used where a device must be monitored or controlled remotely over a pair of conductors. Only one current level can be present at any time.
An electrical contact is an electrical circuit component found in electrical switches, relays, connectors and circuit breakers. Each contact is a piece of electrically conductive material, typically metal. When a pair of contacts touch, they can pass an electrical current with a certain contact resistance, dependent on surface structure, surface chemistry and contact time; when the pair is separated by an insulating gap, then the pair does not pass a current. When the contacts touch, the switch is closed; when the contacts are separated, the switch is open. The gap must be an insulating medium, such as air, vacuum, oil, SF6. Contacts may be operated by humans in push-buttons and switches, by mechanical pressure in sensors or machine cams, and electromechanically in relays. The surfaces where contacts touch are usually composed of metals such as silver or gold alloys that have high electrical conductivity, wear resistance, oxidation resistance and other properties.
An RF switch or microwave switch is a device to route high frequency signals through transmission paths. RF and microwave switches are used extensively in microwave test systems for signal routing between instruments and devices under test (DUT). Incorporating a switch into a switch matrix system enables you to route signals from multiple instruments to single or multiple DUTs. This allows multiple tests to be performed with the same setup, eliminating the need for frequent connects and disconnects. The entire testing process can be automated, increasing the throughput in high-volume production environments.
A H-bridge is an electronic circuit that switches the polarity of a voltage applied to a load. These circuits are often used in robotics and other applications to allow DC motors to run forwards or backwards. The name is derived from its common schematic diagram representation, with four switching elements configured as the branches of a letter "H" and the load connected as the cross-bar.
A solid state relay (SSR) is an electronic switching device that switches on or off when an external voltage is applied across its control terminals. They serve the same function as an electromechanical relay, but as solid-state electronics contain no moving parts and have a longer operational lifetime.
In building wiring, multiway switching is the interconnection of two or more electrical switches to control an electrical load from more than one location. A common application is in lighting, where it allows the control of lamps from multiple locations, for example in a hallway, stairwell, or large room.
A nanoelectromechanical (NEM) relay is an electrically actuatedswitch that is built on the nanometer scale using semiconductor fabrication techniques. They are designed to operate in replacement of, or in conjunction with, traditional semiconductor logic. While the mechanical nature of NEM relays makes them switch much slower than solid-state relays, they have many advantageous properties, such as zero current leakage and low power consumption, which make them potentially useful in next generation computing.
References
↑ “Switch,” The Penguin dictionary of Electronics, 2nd ed, London, UK: Penguin Books, 1998.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
