C mount

Last updated
C-mount
C mount lens Pentax 12mm f1.2.jpg
12 mm f/1.2 C-mount lens with a C-mount–to–CS-mount adapter
TypeScrew
Flange 17.526 millimetres (0.6900 in)

A C mount is a type of lens mount commonly found on 16 mm movie cameras, closed-circuit television cameras, machine vision cameras and microscope phototubes.

Contents

C-mount lenses provide a male thread, which mates with a female thread on the camera. The thread is nominally 1 inch (25.4 mm) in diameter, with 32 threads per inch (0.794 mm pitch), designated as "1-32 UN 2A" in the ANSI B1.1 standard for unified screw threads. The flange focal distance is 17.526 millimetres (0.6900 in) for a C mount.

Merely to say that a lens is "C-mount" says very little about the lens's intended use. C-mount lenses have been made for many different formats. C-mount lenses are built for the 8 mm and 16 mm film formats and the 1/3", 1/2", 2/3", 1", and 4/3" video formats, which corresponds to a range of image circles approximately from 5 to 22 mm in diameter.

Depending on the format, the design of the lens and its performance will differ considerably. For example, for the 4/3 format, a 12 mm lens is a wide-angle lens and will have a retrofocus design. For the 2/3-inch format, a 12 mm lens is "normal" and can have a simple and fast double Gauss layout. For the 1/3-inch format, a 12 mm lens is long and can have a telephoto design.

Some TV lenses lack provision to focus or vary the aperture, so may not operate properly with film cameras. Also, some TV lenses may have bits that protrude behind the mount far enough to interfere with the shutter or reflex finder mechanisms of a film camera.

Although C-mount lenses have a back focal distance far too short to be used with 35 mm film SLRs or any existing digital SLR, they can be mounted on interchangeable-lens mirrorless digital cameras such as the Micro Four Thirds used by Olympus and Panasonic. However, the vast majority of C-mount lenses produce an image circle too small to effectively cover the entire sensor which has approximately 22 mm diagonal, this produces vignetting. [1] The Nikon 1 series and the Pentax Q series can use C-mount lenses without vignetting.

C mount was created by Bell & Howell for their Filmo 70 cine cameras. [2] The earliest Filmos had slightly different mounts, known as A mount, and B mount. C mount was found on Filmo 70 cameras with serial numbers 54090 and higher, [3] probably from about 1926. Soon after, other camera manufacturers adopted the same mount, and it became a de facto standard for 16 mm cine cameras.

CS mount

CS-mount has a flange focal distance of 12.526 millimetres (0.4931 in), [4] [5] compared to 17.526 millimetres (0.6900 in) for a C mount, but is otherwise the same as C-mount, including the fact that lenses for many different formats are made for it. CS-mount lenses are built for the smaller formats, 1/2 inch and down.

Combinations: C, CS and extension adapter
Camera
body		Extension
tube
adapter		LensNet
effect		FocusView
angle		ZoomExposure
CCNormalNormalNormalNormal
CCS+5 mmNear-sightedNarrowerLargerDarker
C5.0 mm (0.20 in)C+5 mmNear-sightedNarrowerLargerDarker
C5.0 mm (0.20 in)CS+10 mmMost near-sightedNarrowestLargestDarkest
CSC−5 mmFar-sightedWiderSmallerBrighter
CSCSNormalNormalNormalNormal
CS5.0 mm (0.20 in)CNormalNormalNormalNormal
CS5.0 mm (0.20 in)CS+5 mmNear-sightedNarrowerLargerDarker

See also

Related Research Articles

Single-lens reflex camera Camera that typically uses a mirror and prism system

A single-lens reflex camera (SLR) is a camera that typically uses a mirror and prism system that permits the photographer to view through the lens and see exactly what will be captured. With twin lens reflex and rangefinder cameras, the viewed image could be significantly different from the final image. When the shutter button is pressed on most SLRs, the mirror flips out of the light path, allowing light to pass through to the light receptor and the image to be captured.

Camera Optical device for recording images

A camera is an optical instrument that captures a visual image. At a basic level, cameras consist of sealed boxes, with a small hole that allows light through to capture an image on a light-sensitive surface. Cameras have various mechanisms to control how the light falls onto the light-sensitive surface. Lenses focus the light entering the camera. The aperture can be narrowed or widened. A shutter mechanism determines the amount of time the photosensitive surface is exposed to light.

The angle of view is the decisive variable for the visual perception of the size or projection of the size of an object.

Four Thirds system Digital camera sensor and lens mount format

The Four Thirds System is a standard created by Olympus and Eastman Kodak for digital single-lens reflex camera (DSLR) and mirrorless camera design and development.

Lens mount Interface between a camera body and lens

A lens mount is an interface – mechanical and often also electrical – between a photographic camera body and a lens. It is a feature of camera systems where the body allows interchangeable lenses, most usually the rangefinder camera, single lens reflex type, single lens mirrorless type or any movie camera of 16 mm or higher gauge. Lens mounts are also used to connect optical components in instrumentation that may not involve a camera, such as the modular components used in optical laboratory prototyping which join via C-mount or T-mount elements.

APS-C Image sensor format

Advanced Photo System type-C (APS-C) is an image sensor format approximately equivalent in size to the Advanced Photo System film negative in its C ("Classic") format, of 25.1×16.7 mm, an aspect ratio of 3:2 and Ø 31.15 mm field diameter. It is therefore also equivalent in size to the Super 35 motion picture film format, which has the dimensions of 24.89 mm × 18.66 mm and Ø 31.11 mm field diameter.

Flange focal distance Property of a lens mount system

For an interchangeable lens camera, the flange focal distance (FFD) of a lens mount system is the distance from the mounting flange to the film or image sensor plane. This value is different for different camera systems. The range of this distance, which will render an image clearly in focus within all focal lengths, is usually measured to a precision of hundredths of millimetres, and is not to be confused with depth of field.

M42 lens mount Screw thread mounting standard for attaching lenses to 35 mm cameras

The M42 lens mount is a screw thread mounting standard for attaching lenses to 35 mm cameras, primarily single-lens reflex models. It is more accurately known as the M42 × 1 mm standard, which means that it is a metric screw thread of 42 mm diameter and 1 mm thread pitch.

Pentax K-mount Series of camera lens mounts made by Pentax

The Pentax K-mount, sometimes referred to as the "PK-mount", is a bayonet lens mount standard for mounting interchangeable photographic lenses to 35 mm single-lens reflex (SLR) cameras. It was created by Pentax in 1975, and has since been used by all Pentax 35 mm and digital SLRs and also the MILC Pentax K-01. A number of other manufacturers have also produced many K-mount lenses and K-mount cameras.

M39 lens mount

The M39 lens mount is a screw thread mounting system for attaching lenses to 35 mm cameras, primarily rangefinder (RF) Leicas. It is also the most common mount for Photographic enlarger lenses.

Yashica Japanese camera manufacturer

Yashica was a Japanese manufacturer of cameras, originally active from 1949 until 2005 when its then-owner, Kyocera, ceased production.

The T-mount is a standard lens mount for cameras and other optical assemblies. The usual T-mount is a screw mount using a male 42×0.75 metric thread on the lens with a flange focal distance of 55 mm and a mating female 42mm thread on a camera adapter or other optical component. This thread form is referred to as T-thread.

Lenses for SLR and DSLR cameras

This article is about photographic lenses for single-lens reflex film cameras (SLRs) and digital single-lens reflex cameras (DSLRs). Emphasis is on modern lenses for 35 mm film SLRs and for DSLRs with sensor sizes less than or equal to 35 mm ("full-frame").

Pancake lens Term for a thin, flat camera lens

A pancake lens is colloquial term for a flat, thin camera lens assembly. The majority are a prime lens of normal or slightly wider angle of view. Some are zoom lenses.

The Fujica X-mount was a lens mount created by Fujifilm in the late 1970s for the new Fujica SLR lineup: AX-1, AX-3, AX-5, STX-1, STX-1N, STX-2. It replaced the M42 screw mount used on their earlier SLRs.

Pentax 6×7

The Pentax 6×7 is a SLR medium format system film camera for 120 and 220 film, which produces images on the film that are nominally 6 cm by 7 cm in size, made by Pentax. It originally debuted in 1965 as a prototype dubbed the Pentax 220. Since then, with improvements, it was released in 1969 as the Asahi Pentax 6×7, as well as the Honeywell Pentax 6×7 for the North American import market. In 1990, it received a number of minor engineering updates and cosmetic changes and was renamed as the Pentax 67.

Sony E-mount

The E-mount is a lens mount designed by Sony for their NEX and ILCE series of camcorders and mirrorless cameras. The E-mount supplements Sony's α mount, allowing the company to develop more compact imaging devices while maintaining compatibility with 35mm sensors. E-mount achieves this by:

Iscorama was a trademark applied by ISCO Optics of Göttingen to a series of consumer-grade anamorphic lenses manufactured between the late 1960s and the beginning of the 21st century. These lenses were notable for their high optical quality and unique focusing characteristics, and with the advent of DSLR-based film making have attracted much interest from independent cinematographers and directors.

Sigma 8-16mm f/4.5-5.6 DC HSM lens Ultra wide-angle rectilinear camera zoom lens

The Sigma 8–16mm lens is an enthusiast-level, ultra wide-angle rectilinear zoom lens made by Sigma Corporation specifically for use with APS-C small format digital SLRs. It is the first ultrawide rectilinear zoom lens with a minimum focal length of 8 mm, designed specifically for APS-C size image sensors. The lens was introduced at the February 2010 Photo Marketing Association International Convention and Trade Show. At its release it was the widest viewing angle focal length available commercially for APS-C cameras. It is part of Sigma's DC line of lenses, meaning it was designed to have an image circle tailored to work with APS-C format cameras. The lens has a constant length regardless of optical zoom and focus with inner lens tube elements responding to these parameters. The lens has hypersonic zoom autofocus.

Lens adapter

In photography and videography, a lens adapter is a device that enables the use of camera and lens combinations from otherwise incompatible systems. The most simple lens adapter designs, passive lens adapters provide a secure physical connection between the camera and the lens. Some passive adapters may include a mechanism for manual iris control. So called, active lens adapters will include electronic connections, enabling communication between the lens and the camera.

References

  1. ↑ Lawrenceripsher.com: Switar 26mm f/1.1 Review Archived December 15, 2009, at the Wayback Machine .
  2. ↑ Yahoo Group discussion: Cine Camera Collectors
  3. ↑ Kodak Movie News, Vol. 2, No. 3 (May–June 1954).
  4. ↑ Hornberg, Alexander (2007-02-27). Handbook of Machine Vision. John Wiley & Sons. ISBN   9783527610143.
  5. ↑ "CS-Mount | Edmund Optics". www.edmundoptics.com. Retrieved 2018-07-28.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.