Cable binding

Last updated
A cable binding with boot, typical of the gear used by the US 10th Mountain Division in World War II and most alpine skiers, including racers, beginning around 1932. Kandahar binding with boot.jpg
A cable binding with boot, typical of the gear used by the US 10th Mountain Division in World War II and most alpine skiers, including racers, beginning around 1932.

Cable bindings, also known as Kandahar bindings or bear-trap bindings, are a type of ski bindings widely used through the middle of the 20th century. It was invented and brand-named after the Kandahar Ski Club in 1929 by ski racer and engineer Guido Reuge. [1] They were replaced in alpine skiing by heel-and-toe "safety bindings" in the mid-1960s.

Contents

The cable binding attaches firmly at the toe only, normally in a trapezoidal metal cup roughly the same as the toe of a boot. A strap is fastened over the toe to stop it from rising out of the cup vertically. [2] Another cable holds the boot forward into the cup, and under the toe strap. If the heel is lifted, causing the boot to rotate in the toe clip, a spring keeps tension on the cable to keep the boot pressed forward.

The Kandahar version added two small metal clips on either side of the boot, normally near the arch or heel. For cross-country skiing the cable was left on top of the clips, allowing the heel to move vertically. For downhill runs, the cable was moved under the clips, forcing the heel down onto the ski. This provided greatly improved control, allowing the skier to torque the skis for turns.

Clipping-in also presents a serious danger, locking the ski to the leg during falls. It was estimated that 10% of all skiers using these bindings were injured during any given season. [3] It was this injury rate that led to the nickname "bear trap", for the way the leg was trapped in the jaws of the binding. [4] [5]

History

A typical late-model cable binding. The boot is inserted into the metal plate, and held down by a leather strap (missing). The cable is then lifted over the heel of the boot, and pulled forward by the lever at the top of the image. The spring keeps constant tension as the boot moves up and down through the striding motion. Skidbindning.JPG
A typical late-model cable binding. The boot is inserted into the metal plate, and held down by a leather strap (missing). The cable is then lifted over the heel of the boot, and pulled forward by the lever at the top of the image. The spring keeps constant tension as the boot moves up and down through the striding motion.

Downhill skiing only developed as a separate sport after the introduction of the ski lift. Prior to this, almost all skiing involved a mix of cross-country, downhill and even uphill skiing. For cross-country, the efficient striding motion requires the heel of the boot to lift from the ski, allowing the leg to lag behind the body as the other ski is moved forward. In the late 1880s, a number of bindings using a leather strap over the toe and a second one pulling the boot forward under the toe strap were common. [4] These kept the toe of the boot on the ski, while allowing the heel to rise some distance.

Fastening the straps to the ski was always a challenge, often requiring slots to be cut into the ski. A key advance was introduced by Fritz R. Huitfeldt, who used a metal plate that was screwed onto the top of the ski with short vertical extensions that had holes to attach the straps to. The major advantage to this design is that the vertical extensions held the boot firmly centered on the ski, whereas the former all-strap systems generally had considerable flop. Variations on this design led to the shaping of the metal plate to progressively hold the toe more firmly. [4]

An evolution of the Huitfeldt designs was the replacement of the heel strap with a metal cable and springs. Invented in 1929 by the Swiss ski racer Guido Reuge, patented by him and marketed in 1932, the spring-loaded cable binding was named for the Lord Roberts of Kandahar Cup ski races. [6] Kandahar-style cable bindings would be almost universal into the early 1960s. [4]

The Kandahar design offered two advantages over the earlier designs. The use of a spring to provide tension allowed fine control over the mechanics, and a smooth action that did not suddenly increase tension at the end of the stroke. It also allowed the skier to adjust the tension by moving the spring or turning a control knob, allowing for different conditions and skiing style and stride. More important was the addition of two small hooks on either side of the ski near the heel. When skiing downhill, the skier could clip the cable under the hooks, locking down the heel and providing much greater control. Now the ski could be turned by rotating the leg, forcing the ski to stem. When it was time to climb back up the hill, the cable was unhooked and returned to being a normal cross-country binding. [4]

The introduction of dedicated ski lifts in the late 1930s led to an evolution of skiing as a sport. In the past, skiers would have to ski or walk up the hills they intended to ski down. With the lift, the skiers could leave their skis on, and would be skiing downhill all the time. The need to unclip the heel for cross-country use was eliminated, at least at resorts with lifts. The cable binding became a must-have. Cable bindings were almost universal by the late-1930s, and used famously by the US 10th Mountain Division during World War II. [4]

For pure downhill skiing, the Kandahar was a problem. In particular, the metal toe clip so tightly clamped the front of the boot that even small sideways motions of the tip of the ski could twist the lower leg, and spiral fractures of the calf were common. The death grip led to the nickname "bear trap bindings", and it was estimated that 1% of skiers suffered an injury on any given day. [7]

During the 1930s it was discovered that an improvement could be made by removing the toe strap from a typical Kandahar binding. Instead, the metal cup was bent inward to slightly wrap over the top of the boot, or at least the top of the sole. Although the resulting clip was much less solid than the strap, in the case of a forward fall the boot would rotate up and out of the cup, releasing the leg. Although this was an improvement, it was a small one.

In the post-war era, the introduction of "safety bindings" replaced the toe plate with more complex auto-release systems, while retaining the heel cable to keep the boot against the toe binding. Over time, the heel cable was replaced with new clip-on binding designs, starting in the late 1950s. By the late 1960s, bear-trap bindings had largely disappeared from the alpine skiing world. [7]

Related Research Articles

<span class="mw-page-title-main">Snowboard</span> Winter sport equipment

Snowboards are boards where the user places both feet, usually secured, to the same board. The board itself is wider than most skis, with the ability to glide on snow. Snowboards widths are between 6 and 12 inches or 15 to 30 centimeters. Snowboards are differentiated from monoskis by the stance of the user. In monoskiing, the user stands with feet inline with direction of travel, whereas in snowboarding, users stand with feet transverse to the longitude of the board. Users of such equipment may be referred to as snowboarders. Commercial snowboards generally require extra equipment such as bindings and special boots which help secure both feet of a snowboarder, who generally ride in an upright position. These types of boards are commonly used by people at ski hills, mountains, backcountry, or resorts for leisure, entertainment, and competitive purposes in the activity called snowboarding.

<span class="mw-page-title-main">Skiing</span> Recreational activity and sport using snow skis

Skiing is the use of skis to glide on snow. Variations of purpose include basic transport, a recreational activity, or a competitive winter sport. Many types of competitive skiing events are recognized by the International Olympic Committee (IOC), and the International Ski and Snowboard Federation (FIS).

<span class="mw-page-title-main">Alpine skiing</span> Sport of skiing downhill

Alpine skiing, or downhill skiing, is the pastime of sliding down snow-covered slopes on skis with fixed-heel bindings, unlike other types of skiing, which use skis with free-heel bindings. Whether for recreation or for sport, it is typically practiced at ski resorts, which provide such services as ski lifts, artificial snow making, snow grooming, restaurants, and ski patrol.

<span class="mw-page-title-main">Ice skate</span> Boots with blades attached to the bottom for propelling the bearer across a sheet of ice

Ice skates are metal blades attached underfoot and used to propel the bearer across a sheet of ice while ice skating.

<span class="mw-page-title-main">Snowshoe</span> Footwear for walking easily across snow

Snowshoes are specialized outdoor gear for walking over snow. Their large footprint spreads the user's weight out and allows them to travel largely on top of rather than through snow. Adjustable bindings attach them to appropriate winter footwear.

<span class="mw-page-title-main">History of skiing</span> Skiing from 7000 BC to today

Skiing, or traveling over snow on skis, has a history of at least eight millennia. The earliest archaeological examples of skis were found in Karelia and date to 6000 BCE. Although skiing's origins were purely utilitarian, the modern sport evolved from beginnings in Scandinavia, starting in the mid-1800s skiing became a popular recreational activity and sport, becoming practiced in snow-covered regions worldwide, and providing a market for the development of ski resorts and their related communities.

<span class="mw-page-title-main">Telemark skiing</span> Skiing technique

Telemark skiing is a skiing technique that combines elements of Alpine and Nordic skiing, using the rear foot to keep balance while pushing on the front foot to create a carving turn on downhill skis with toe-only bindings. Telemark skiing is named after the Telemark region of Norway, where the discipline originated. Sondre Norheim is often credited for first demonstrating the turn in ski races, which included cross country, slalom, and jumping, in Norway around 1868. Sondre Norheim also experimented with ski and binding design, introducing side cuts to skis and heel bindings.

<span class="mw-page-title-main">Ski binding</span> Connects skier boot to snow ski

A ski binding is a device that connects a ski boot to the ski. Before the 1933 invention of ski lifts, skiers went uphill and down and cross-country on the same gear. As ski lifts became more prevalent, skis—and their bindings—became increasingly specialized, differentiated between alpine (downhill) and Nordic styles of skiing. Until the point of divergence in the mid-20th century, bindings held the toe of a flexible, leather boot against the ski and allowed the heel to rise off the ski, typically with a form of strap or cable around the heel.

Ski boots are footwear used in skiing to provide a way to attach the skier to skis using ski bindings. The ski/boot/binding combination is used to effectively transmit control inputs from the skier's legs to the snow.

<span class="mw-page-title-main">Crampons</span> Traction device for ice-climbing

A crampon is a traction device attached to footwear to improve mobility on snow and ice during ice climbing. Besides ice climbing, crampons are also used for secure travel on snow and ice, such as crossing glaciers, snowfields and icefields, ascending snow slopes, and scaling ice-covered rock.

Marker International is a German manufacturing company of equipment for winter sports established in 1952 and headquartered in Straubing, Lower Bavaria. Founded by Hannes Marker, the company is known for pioneering releasable binding technology. Marker's first model, the Duplex was followed in 1953 by the Simplex toe binding which was a huge success in the 1950s. New models introduced in the 1980s were major competitors on the alpine racing circuit.

<span class="mw-page-title-main">Nava System</span>

The Nava System was a ski binding and custom ski boot offered for sale in the 1980s. The system used a combination of flexible sole plate to keep the boot centered, and a spring-loaded plastic arm on the rear binding that was used to transmit sideways motions of the leg to the ski. This eliminated the need for a hard shell on the boot; the Nava boot was soft and resembled a knee-high winter boot. In spite of numerous endorsements by racing stars, the system never caught on and sales ended by the late 1980s.

<span class="mw-page-title-main">Spademan binding</span>

Spademan was a type of ski binding, one of a number of "plate bindings" that were popular in alpine skiing during the 1970s. It used a bronze plate screwed into the bottom of the boot as its connection point, held to the ski by a clamp-like mechanism that grasped the side of the plate. Unlike conventional bindings, the Spademan could release in any direction, in response to any force or torque. It provided greatly improved protection compared to contemporary designs, which generally allowed release of the toe to the sides and heel directly forward, keeping the foot attached in any other fall direction.

<span class="mw-page-title-main">Look Nevada</span>

Look's Nevada, released in 1950, was the first recognizably modern alpine ski binding. The Nevada was only the toe portion of the binding, and was used with a conventional cable binding for the heel. An updated version was introduced in 1962 with a new step-in heel binding, the Grand Prix. These basic mechanisms formed the basis for LOOK bindings for over 40 years, changing mainly in name and construction materials. The Nevada toe pattern is almost universal among bindings today.

<span class="mw-page-title-main">Look Integral</span>

The Look Integral was a downhill ski binding that worked in conjunction with a custom ski boot made by Nordica. The Integral was fairly common in ski rental shops in the 1980s and into the 90s, but has since disappeared.

Hanson Industries invented and popularized the rear-entry ski boot. Formed by brothers Chris and Denny Hanson in 1969, the company became a huge success in the late 1970s. A series of missteps in the early 1980s led to a rapid death spiral and the company went bankrupt in 1984. It was purchased by Daiwa, a Japanese fishing tackle company that handled Hanson's distribution in Japan. Daiwa ended sales in North America and Europe. European products, notably the famous Salomon SX series, used Hanson's exit as a springboard to market domination during the second half of the 1980s. Denny Hanson later introduced the "Apex" design, which combines features of alpine and snowboarding boots.

<span class="mw-page-title-main">Rosemount Ski Boots</span> Plastic ski boots

Rosemount Ski Boots introduced one of the earliest all-plastic ski boots for the downhill skiing market, competing with Bob Lange for the title of "first". Rosemount's design was easily distinguished by its use of the uncommon "side-entry" method for putting the boot on, which was rare at the time and is no longer used.

<span class="mw-page-title-main">Lange (ski boots)</span> Ski boot manufacturer

Lange is a major producer of ski boots used in alpine (downhill) skiing, founded in 1948 in the USA. They introduced the world's first plastic ski boots in 1962, and a greatly improved model aimed at the racing market in 1965. After several World Cup and Olympics wins in 1967 and 1968 made them a must-have on the circuit, Lange has remained a force in the racing market ever since. Their boots have equipped five times as many World Cup medal winners as any other brand into the 2000s. The front-entry design introduced by Lange is used by almost every modern ski boot to this day. Lange remains a major brand worldwide.

<span class="mw-page-title-main">Raichle Flexon</span>

The Flexon was a downhill ski boot introduced by Raichle in the winter of 1980/81. Based on designs by Sven Coomer, Al Gross and Erik Giese, the Flexon used a unique system to control forward flex in a predictable way, as well as making the boot more comfortable and easier to put on and remove. The basic layout was, and is, generally referred to as a "three-piece" design -- three-piece boots preceding the Flexon included the Henke Strato, Nordica Comp 3 and a dozen other designs from Italian bootmakers.

This glossary of skiing and snowboarding terms is a list of definitions of terms and jargon used in skiing, snowboarding, and related winter sports.

References

Citations

  1. Roland Huntford, "Two Planks and a Passion
  2. Lert, p. 25
  3. Lert, p. 39
  4. 1 2 3 4 5 6 Lert, p. 26
  5. Lund, p. 10
  6. Luzi Hitz, History of Swiss Ski Technology, http://skiinghistory.org/history/history-swiss-ski-technology-and-instruction/
  7. 1 2 Masia, pg. 26

Bibliography