DC-BUS

Last updated

DC-BUS is technology for reliable and economical communication over noisy DC or AC power lines. The DC-BUS was originally developed by Yamar Electronics Ltd. [1] together with the DC-BUS Alliance, [2] for low cost sub-networks in vehicles, using the battery lines for in-vehicle data communication. The DC-BUS converts the digital input data into phase modulated signals, protected against errors generated by noise over the powerline. On the receiving side, the received signal is demodulated into the original digital data. [3] Gradually it became a popular[ dubious – discuss ] means of communication [4] in a plurality of applications within aerospace, automotive, solar energy management and lighting. It is also used as an alternative to RS-232 and RS-485 networks in some cases. The common goal for all these applications is reducing wires, saving space, lowering cost and increasing reliability.

Contents

Technology

The DC-BUS is a physical layer that allows transmission of data over the powerline and receiving that signal even if attenuated to the noise level of the powerline. DC-BUS is one of several protocols for power-line communication.

Two technologies implement the DC-BUS: byte oriented and message oriented.

The signaling technology is byte oriented, allowing transfer of a single UART data byte or more over noisy channel (such as the powerline) at bit-rate up to 115.2 kbit/s; each transmitted byte is protected against errors caused by noisy environment. This method operates on a customer selected channel ranging in the HF band. A unique narrow band signaling modulation, based on combination of phase changes is used to transfer each byte. There is no restriction to the number of bytes, therefore, any UART-based standards such as RS-232, RS-485 and LIN-bus can use the DC-BUS as a physical layer. The received data by all the other nodes on that channel has a fixed latency of 3.5 bits. This simplicity of use allows every customer to design his own protocol or use common industry protocols such as LIN. A master slave upper layer protocol is suitable for network operation.

The DCB technology is message oriented, currently operating at speeds up to 1.3Mbit/s. The DCB devices use a selectable narrowband carrier to communicate over the powerline. The DCB gets a message of any length from its host controller and phase modulates it over the power line. The DCB devices have built-in CSMA/CR mechanism for collision detection and arbitration for network operation. The DCB interfaces with its host controller using standard UART or SPI protocols. The use of low level modulated sine wave instead of digital square wave usually between 0 and 12V generates lower unintentional radiation (EMC). [5] The DC-BUS has a sleep mechanism to wake up the DC-BUS devices during sleep mode (low power consumption).

Applications

Automotive

The average modern car contains 1.5 kilometers of copper wire. [6] [7] Wiring plays a significant role in automotive, a passenger car has between 500 and 1500 wires, and these numbers are growing despite the extensive use of CAN and LIN buses. Powerline is common to all the electric modules in a vehicle. The DC-BUS uses these power lines for communication. There are many applications some of them are described hereby.

Truck-trailer communication

As part of the SPARC European project conducted by Daimler, [8] two DC-BUS communication networks were used between the truck and the trailer over the existing DC powerline. One network operated at a carrier frequency of 5 MHz for CAN redundant high speed data. The other network operated at 6.5 MHz for trailer backlights activation and control. It saved the existing lights cable between the truck and the trailer. The figure below describes the two networks saving the need for the expensive cable between the truck and the trailer. The experimental InnoTruck used the DC-BUS for its lights control. [9]

Doors and mirrors control

The DC-BUS can save all the wiring in doors assemblies and its mirrors by using the powerline to control the window, lock and mirror functions (up, down, left, right, blinker, etc.). Only the powerline connects the door to the vehicle body, saving connector and wires. The use of the powerline allows controlling the entertainment unit from the doors, saving the dashboard space.

Steering-wheel control

The figure below presents a steering wheel with a SIG61 device gathering all its switches status and transferring the data over the powerline to the vehicle ECU via the clock-spring saving many wires, reducing the clock spring complexity and cost.

Electrical vehicle battery management

Electrical vehicle (EV) high voltage battery is constructed from serially connected battery power-packs consisting of rechargeable battery cells such as lithium-ion. Each cell has to be monitored for proper operation within specified temperature and voltage range. Each power-pack gathers its cell's status and transfers it to the vehicle's battery management system (BMS). Each power-pack is connected at a different voltage reference level. In traditional solution, in order to transfer data, the EV power-packs are connected to the BMS via high voltage data lines, connectors and voltage level shifters. The use of DC-BUS eliminates the need for extra wires, using the powerline as a micro-grid between the power-packs and the BMS. The powerline communication is coupled to the BMS via capacitors that provide galvanic separation between the high voltage powerline and the vehicle's 12/24 V powerline.

Solar panels energy management

Photovoltaic system is constructed from arrays of solar panels and a central energy controller. Communicating between the panels and the central energy management controller allows optimization of each solar panel operating point to increase the entire system energy efficiency and to monitor its proper operation. The DC-BUS constructs a micro-grid over the DC powerline without a need of extra wires. Strings of solar PV panels form entire data network over the high voltage powerline.

Aerospace

Saving wires in aerospace applications is obvious. The DC-BUS was used in the European SCARLETT project for harness reduction purposes. [10]

Home appliances

Harness of white goods products can be reduced significantly by use of AC/DC-BUS between its modules. The new architecture use only two 24 V DC wires and two 110/220 V AC wires connecting all modules within the white goods products. Yamar's semiconductors use these lines for data communication over noisy power lines; activating loads and reading sensors without need for extra wires.

The 24 V line carries the power required to operate the internal modules as well as for communication between these modules. The 110/220 V wires operate the heavy loads such as compressors and motors. Figure 1 describes a common system that is applicable in washing machines, air conditioners and more.

Lighting - smart home

The new generation of illumination devices (LED, CFL bulbs) contains already electronic circuitry. The DC-BUS powerline communication within these bulbs upgrades its functionality as "smart-bulb". Smart-bulb becomes an intelligent sensing and actuation center in addition to its traditional lighting functionality. Each bulb has its own functionality and address allowing controlling its light intensity, color as well as reading the status of its attached sensors. Examples for such sensors are: motion detector, temperature gage, smoke detector etc. Reading data from one smart-bulb can determine the functionality of other smart-bulbs connected to the same powerline.

Standards

Limitations

Attenuation of the DC-BUS signal is the main constraint on cable length. For a carrier signal in the HF band, an inductive load such as a motor causes only minor attenuation, but a filtering capacitor represents an extreme attenuation and thus reduces the usable range of the DC-BUS. A DC-BUS device connected close to the battery will have its range further reduced.

Devices which generate significant HF-band signal, such as alternators or microcontroller-based electronics, may cause interference with a poorly-chosen DC-BUS carrier frequency, if they are poorly filtered. Alternately, their filters may significantly attenuate the DC-BUS carrier. Either option reduces the reliability and range of the DC-BUS.

In general, any noise filtering or EMI protection circuitry may significantly reduce the effective range of the DC-BUS, if it attenuates frequencies near the DC-BUS carrier.

Related Research Articles

In telecommunications, RS-232, Recommended Standard 232 is a standard originally introduced in 1960 for serial communication transmission of data. It formally defines signals connecting between a DTE such as a computer terminal, and a DCE, such as a modem. The standard defines the electrical characteristics and timing of signals, the meaning of signals, and the physical size and pinout of connectors. The current version of the standard is TIA-232-F Interface Between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange, issued in 1997. The RS-232 standard had been commonly used in computer serial ports and is still widely used in industrial communication devices.

Direct current Unidirectional flow of electric charge

Direct current (DC) is the unidirectional flow of an electric charge. An electrochemical cell is a prime example of DC power. Direct current may flow through a conductor such as a wire, but can also flow through semiconductors, insulators, or even through a vacuum as in electron or ion beams. The electric current flows in a constant direction, distinguishing it from alternating current (AC). A term formerly used for this type of current was galvanic current.

A universal asynchronous receiver-transmitter is a computer hardware device for asynchronous serial communication in which the data format and transmission speeds are configurable. The electric signaling levels and methods are handled by a driver circuit external to the UART. A UART is usually an individual integrated circuit (IC) used for serial communications over a computer or peripheral device serial port. One or more UART peripherals are commonly integrated in microcontroller chips. A related device, the universal synchronous and asynchronous receiver-transmitter (USART) also supports synchronous operation.

Serial port communication interface socket/plug

In computing, a serial port is a serial communication interface through which information transfers in or out sequentially one bit at a time. This is in contrast to a parallel port which communicates multiple bits simultaneously in parallel. Throughout most of the history of personal computers, data was transferred through serial ports to devices such as modems, terminals, and various peripherals.

AVR microcontrollers family of microcontrollers

AVR is a family of microcontrollers developed since 1996 by Atmel, acquired by Microchip Technology in 2016. These are modified Harvard architecture 8-bit RISC single-chip microcontrollers. AVR was one of the first microcontroller families to use on-chip flash memory for program storage, as opposed to one-time programmable ROM, EPROM, or EEPROM used by other microcontrollers at the time.

Low-voltage differential signaling technical standard

Low-voltage differential signaling, or LVDS, also known as TIA/EIA-644, is a technical standard that specifies electrical characteristics of a differential, serial communication protocol. LVDS operates at low power and can run at very high speeds using inexpensive twisted-pair copper cables. LVDS is a physical layer specification only; many data communication standards and applications use it and add a data link layer as defined in the OSI model on top of it.

Serial communication Type of data transfer

In telecommunication and data transmission, serial communication is the process of sending data one bit at a time, sequentially, over a communication channel or computer bus. This is in contrast to parallel communication, where several bits are sent as a whole, on a link with several parallel channels.

GeoPort is a serial data system used on some models of the Apple Macintosh that could be externally clocked to run at a 2 Mbit/s data rate. GeoPort slightly modified the existing Mac serial port pins to allow the computer's internal DSP hardware or software to send data that, when passed to a digital-to-analog converter, emulated various devices such as modems and fax machines. GeoPort could be found on late-model 68K-based machines as well as many pre-USB Power Macintosh models. Some later Macintosh models also included an internal GeoPort via an internal connector on the Communications Slot. Apple GeoPort technology is now obsolete, and modem support is typically offered through USB.

A Controller Area Network is a robust vehicle bus standard designed to allow microcontrollers and devices to communicate with each other's applications without a host computer. It is a message-based protocol, designed originally for multiplex electrical wiring within automobiles to save on copper, but can also be used in many other contexts. For each device the data in a frame is transmitted sequentially but in such a way that if more than one device transmits at the same time the highest priority device is able to continue while the others back off. Frames are received by all devices, including by the transmitting device.

Power-line communication (PLC) carries data on a conductor that is also used simultaneously for AC electric power transmission or electric power distribution to consumers. It is also known as power-line carrier, power-line digital subscriber line (PDSL), mains communication, power-line telecommunications (PLT), or power-line networking (PLN).

The System Management Bus is a single-ended simple two-wire bus for the purpose of lightweight communication. Most commonly it is found in computer motherboards for communication with the power source for ON/OFF instructions.

1-Wire Device communications bus system

1-Wire is a device communications bus system designed by Dallas Semiconductor Corp. that provides low-speed data, signaling, and power over a single conductor.

Broadband over power lines (BPL) is a method of power line communication (PLC) that allows relatively high-speed digital data transmission over the public electric power distribution wiring. BPL uses higher frequencies, a wider frequency range and different technologies from other forms of power-line communications to provide high-rate communication over longer distances. BPL uses frequencies which are part of the radio spectrum allocated to over-the-air communication services; therefore the prevention of interference to, and from, these services is a very important factor in designing BPL systems.

LIN is a serial network protocol used for communication between components in vehicles. The need for a cheap serial network arose as the technologies and the facilities implemented in the car grew, while the CAN bus was too expensive to implement for every component in the car. European car manufacturers started using different serial communication technologies, which led to compatibility problems.

HomePlug is the family name for various power line communications specifications under the HomePlug designation, with each offering unique performance capabilities and coexistence or compatibility with other HomePlug specifications.

RS-485, also known as TIA-485(-A) or EIA-485, is a standard defining the electrical characteristics of drivers and receivers for use in serial communications systems. Electrical signaling is balanced, and multipoint systems are supported. The standard is jointly published by the Telecommunications Industry Association and Electronic Industries Alliance (TIA/EIA). Digital communications networks implementing the standard can be used effectively over long distances and in electrically noisy environments. Multiple receivers may be connected to such a network in a linear, multidrop bus. These characteristics make RS-485 useful in industrial control systems and similar applications.

The RS-449 specification, also known as EIA-449 or TIA-449, defines the functional and mechanical characteristics of the interface between data terminal equipment, typically a computer, and data communications equipment, typically a modem or terminal server. The full title of the standard is EIA-449 General Purpose 37-Position and 9-Position Interface for Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange.

Digital Addressable Lighting Interface (DALI) is a trademark for network-based products that control lighting. The underlying technology was established by a consortium of lighting equipment manufacturers as a successor for 1-10 V/0–10 V lighting control systems, and as an open standard alternative to several proprietary protocols. The DALI, DALI-2 and D4i trademarks are owned by the lighting industry alliance, DiiA.

A battery management system (BMS) is any electronic system that manages a rechargeable battery, such as by protecting the battery from operating outside its safe operating area, monitoring its state, calculating secondary data, reporting that data, controlling its environment, authenticating it and / or balancing it.

In building automation, eBUS is a 2-wire digital serial data-bus communication interface used in heating and solar energy appliances, by mainly German manufacturers. It was originally proposed by the Karl Dungs company, and has since been adopted by several other manufacturers. The eBUS interface has also been used by home-automation enthusiasts to connect their domestic solar or heating system to a networked PC for monitoring or remote control.

References

  1. ↑ "Yamar Electronics LTD".
  2. ↑ "The New Automotive 42V PowerNet - Alfons Graf page 192 - objective of the DC-BUS Alliance"
  3. ↑ The New Automotive 42V PowerNet - Alfons Graf page 191 - The principle of Power Line Communication"
  4. ↑ "Yamar DC Power-Line Bus Gains Momentum - Hansen Report"
  5. ↑ "2009 ESA Workshop on Aerospace EMC P1.11 - European Space Agency"". Archived from the original on 2013-08-18. Retrieved 2013-08-18.
  6. ↑ Ruud Huijer. "Wiring diagram: then and now".
  7. ↑ "Copper - A Driving Force Behind the Automotive Industry"
  8. ↑ "SPARC FP6 Project"
  9. ↑ "InnotTruck video"
  10. ↑ "Scarlett project"
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.