Junctor

Last updated

A junctor is a circuit used in analog telephone exchanges, including the Number One Crossbar Switching System, Number Five Crossbar Switching System, 1ESS switch and other switches.

In early electromechanical switches, a "district junctor" handled supervision and talk battery duties for outgoing calls, [1] similar to the duties of the cord circuit of manual exchanges. The junctors for incoming calls were simple three-wire connections between the incoming frame and the line frame. In the later electromechanical 5XB switch, junctors only consisted of three wires to connect the two legs of a call: the line and the trunk, [2] of which the latter supplied all talk battery and supervision.

Stored-program analog switches such as the 1ESS switch, had both simple wire junctors and circuit junctors. Circuit junctors were in the form of plug-in circuit boards to provide talk battery and supervision for intraoffice calls and were closely similar to intraoffice trunk packs, with two scan points and two signal distributor points per circuit, two circuits per plug-in pack. Wire junctors were two-wire connections between trunk nets and other trunk nets or line nets. When three-way calling was introduced, three-port conference trunks were used, which only appeared on trunk nets. All junctors appeared in subgroups of sixteen on plugs or jacks at the Junctor Grouping Frame, where as many subgroups as required were plugged into other trunk nets, line nets, or circuit junctor frames.

Related Research Articles

Telephone switchboard

Throughout the 20th century, telephone switchboards were devices used to connect circuits of telephones to establish telephone calls between users or other switchboards. The switchboard was an essential component of a manual telephone exchange, and was operated by switchboard operators who used electrical cords or switches to establish the connections.

Telephone Telecommunications device

A telephone is a telecommunications device that permits two or more users to conduct a conversation when they are too far apart to be heard directly. A telephone converts sound, typically and most efficiently the human voice, into electronic signals that are transmitted via cables and other communication channels to another telephone which reproduces the sound to the receiving user. The term is derived from Greek: τῆλε and φωνή, together meaning distant voice. A common short form of the term is phone, which came into use almost immediately after the first patent was issued.

5ESS Switching System

The 5ESS Switching System is a Class 5 telephone electronic switching system developed by Western Electric for the American Telephone and Telegraph Company (AT&T) and the Bell System in the United States. It came into service in 1982 and the last unit was produced in 2003.

Crossbar switch Collection of electronic switches arranged in a matrix

In electronics and telecommunications, a crossbar switch is a collection of switches arranged in a matrix configuration. A crossbar switch has multiple input and output lines that form a crossed pattern of interconnecting lines between which a connection may be established by closing a switch located at each intersection, the elements of the matrix. Originally, a crossbar switch consisted literally of crossing metal bars that provided the input and output paths. Later implementations achieved the same switching topology in solid-state electronics. The crossbar switch is one of the principal telephone exchange architectures, together with a rotary switch, memory switch, and a crossover switch.

Blue box Device for hacking telephone network

A blue box is an electronic device that produces tones used to generate the in-band signaling tones formerly used within the North American long-distance telephone network to send line status and called number information over voice circuits. This allowed the user, referred to as a "phreaker", to surreptitiously place long-distance calls that would be billed to another number or dismissed entirely as an incomplete call. A number of similar "color boxes" were also created to control other aspects of the phone network.

Nonblocking minimal spanning switch

A nonblocking minimal spanning switch is a device that can connect N inputs to N outputs in any combination. The most familiar use of switches of this type is in a telephone exchange. The term "non-blocking" means that if it is not defective, it can always make the connection. The term "minimal" means that it has the fewest possible components, and therefore the minimal expense.

Business telephone system Multiline telephone system typically used in business environments

A business telephone system is a multiline telephone system typically used in business environments, encompassing systems ranging in technology from the key telephone system (KTS) to the private branch exchange (PBX).

Signalling System R2 is a signalling protocol for telecommunications that was in use from the 1960s mostly in Europe, and later also in Latin America, Asia, and Australia, to convey exchange information between two telephone switching systems for establishing a telephone call via a telephone trunk. It is suitable for signaling on analog as well as digital circuits.

Wire spring relay

A wire spring relay is a type of relay, that has springs made from drawn wires of nickel silver, rather than cut from flat sheet metal as in the flat-spring relay. This class of relays provided manufacturing and operating advantages over previous designs. Wire spring relays entered mass production in the early 1950s.

Stored program control (SPC) is a telecommunications technology used for telephone exchanges controlled by a computer program stored in the memory of the switching system. SPC was the enabling technology of electronic switching systems (ESS) developed in the Bell System in the 1950s, and may be considered the third generation of switching technology. Stored program control was invented in 1954 by Bell Labs scientist Erna Schneider Hoover, who reasoned that computer software could control the connection of telephone calls.

In telecommunication, supervision is the monitoring of a telecommunication circuit for telephony to convey to an operator, user, or a switching system, information about the operational state of the circuit. The typical operational states of trunks and lines are the idle and busy states, seizure, and disconnect. The states are indicated by various electrical signals and electrical conditions depending on the type of circuit, the type of terminating equipment, and the type of intended service.

Reed relay Electromagnetic switching device

A reed relay is a type of relay that uses an electromagnet to control one or more reed switches. The contacts are of magnetic material and the electromagnet acts directly on them without requiring an armature to move them. Sealed in a long, narrow glass tube, the contacts are protected from corrosion. The glass envelope may contain multiple reed switches or multiple reed switches can be inserted into a single bobbin and actuate simultaneously. Reed switches have been manufactured since the 1930s.

Automatic message accounting (AMA) provides detailed accounting for telephone calls. When direct distance dialing (DDD) was introduced in the US, message registers no longer sufficed for dialed telephone calls. The need to record the time and phone number of each long-distance call was met by electromechanical data processing equipment.

The Number Five Crossbar Switching System is a telephone switch for telephone exchanges designed by Bell Labs and manufactured by Western Electric starting in 1947. It was used in the Bell System principally as a Class 5 telephone switch in the public switched telephone network (PSTN) until the early 1990s, when it was replaced with electronic switching systems. Variants were used as combined Class 4 and Class 5 systems in rural areas, and as a TWX switch.

A class-4, or tandem, telephone switch is a U.S. telephone company central office telephone exchange used to interconnect local exchange carrier offices for long distance communications in the public switched telephone network.

The Number One Crossbar Switching System (1XB), was the primary technology for urban telephone exchanges served by the Bell System in the mid-20th century. Its switch fabric used the electromechanical crossbar switch to implement the topology of the panel switching system of the 1920s. The first No. 1 Crossbar was installed in the PResident-2 central office at Troy Avenue in Brooklyn, New York which became operational in February 1938.

Number One Electronic Switching System Defunct telecommunications node in the United States; part of the Bell System

The Number One Electronic Switching System (1ESS) was the first large-scale stored program control (SPC) telephone exchange or electronic switching system in the Bell System. It was manufactured by Western Electric and first placed into service in Succasunna, New Jersey, in May 1965. The switching fabric was composed of a reed relay matrix controlled by wire spring relays which in turn were controlled by a central processing unit (CPU).

The Switching Control Center System was an operations support system developed by Bell Laboratories and deployed during the early 1970s. This computer system was first based on the PDP-11 product line from Digital Equipment Corporation and used the CB Unix operating system and custom application software and device drivers that were developed and maintained by Bell Labs in Columbus, Ohio USA. SCCS was ported to the AT&T 3B20 and 3B5 computers running UNIX System V Release 2 in the early 1980s.

Telephone exchange Interconnects telephones for calls

A telephone exchange, telephone switch, or central office is a telecommunications system used in the public switched telephone network (PSTN) or in large enterprises. It interconnects telephone subscriber lines or virtual circuits of digital systems to establish telephone calls between subscribers.

Panel switch

The Panel Machine Switching System is a type of automatic telephone exchange for urban service that was used in the Bell System in the United States for seven decades. The first semi-mechanical types of this design were installed in 1915 in Newark, New Jersey, and the last were retired in the same city in 1983.

References

  1. Scudder, F.J.; Reynolds, J.N. (January 1939). "Crossbar Dial Telephone Switching System". Bell System Technical Journal . 19 (1): 90.
  2. Bell Telephone Laboratories (1949). No. 5 Crossbar - Bell Labs Record Compilation. pp. 20–25.