Knockdown texture is a drywall finishing style. It is a mottled texture, it has more changes in textures than a simple flat finish, but less changes than orange peel, or popcorn, texture.
Heavy knockdown applied with a spray hopper.
Knockdown texture is created by watering down joint compound to a soupy consistency. A trowel is then used to apply the joint compound. The joint compound will begin to form stalactites as it dries. The trowel is then run over the surface of the drywall, knocking off the stalactites and leaving the mottled finish.
A much more common, and faster technique is to apply the texture mud (which is slightly different from joint compound, in that it has less shrinkage upon drying) with a texture machine – a compressor and a texture spray hopper which sprays mud instead of paint. This applies what is referred to as a splatter coat. The use of a compressor allows this to be applied to walls as well as ceilings. When knocking this down, the mud is allowed to dry for a short period, then skimmed with a knockdown knife – a large, usually plastic (to reduce noticeable edges) knife.
Knockdown texture reduces construction costs because it conceals imperfections in the drywall that normally require higher more expensive stages of sand and prime for drywall installers.
Related Research Articles
An airbrush is a small, air-operated tool that atomizes and sprays various media, most often paint, but also ink, dye, and foundation. Spray painting developed from the airbrush and is considered to employ a type of airbrush.
Drywall is a panel made of calcium sulfate dihydrate (gypsum), with or without additives, typically extruded between thick sheets of facer and backer paper, used in the construction of interior walls and ceilings. The plaster is mixed with fiber ; plasticizer, foaming agent; and additives that can reduce mildew, flammability, and water absorption.
Knockdown or knock-down may refer to:
Spray painting is a painting technique in which a device sprays coating material through the air onto a surface. The most common types employ compressed gas—usually air—to atomize and direct the paint particles.
A trowel is a small hand tool used for digging, applying, smoothing, or moving small amounts of viscous or particulate material. Common varieties include the masonry trowel, garden trowel, and float trowel.
A primer or undercoat is a preparatory coating put on materials before painting. Priming ensures better adhesion of paint to the surface, increases paint durability, and provides additional protection for the material being painted.
Siping is a process of cutting thin slits across a rubber surface to improve traction in wet or icy conditions.
Plasterwork is construction or ornamentation done with plaster, such as a layer of plaster on an interior or exterior wall structure, or plaster decorative moldings on ceilings or walls. This is also sometimes called pargeting. The process of creating plasterwork, called plastering or rendering, has been used in building construction for centuries. For the art history of three-dimensional plaster, see stucco.
A plasterer is a tradesman or tradesperson who works with plaster, such as forming a layer of plaster on an interior wall or plaster decorative moldings on ceilings or walls. The process of creating plasterwork, called plastering, has been used in building construction for centuries. A plasterer is someone who does a full 4 or 2 years apprenticeship to be fully qualified.
Spackling paste or spackle is a putty used to fill holes, small cracks, and other minor surface defects in wood, drywall, and plaster. Typically, spackling is composed of gypsum plaster from hydrated calcium sulfate and glue.
Joint compound is a white powder of primarily gypsum dust mixed with water to form a paste the consistency of cake frosting, which is spread onto drywall and sanded when dry to create a seamless base for paint on walls and ceilings.
A taping knife or joint knife is a drywall tool with a wide blade for spreading joint compound, also known as "mud". It can be used to spread mud over nail and screw indents in new drywall applications and is also used when using paper or fiberglass drywall tape to cover seams. Other common uses include patching holes, smoothing wall-coverings and creating specialty artistic wall finishes. Common sizes range from 15cm to 30cm wide. Spackle knives are a smaller version, used for patching small holes.
A cement board is a combination of cement and reinforcing fibers formed into sheets, of varying thickness that are typically used as a tile backing board. Cement board can be nailed or screwed to wood or steel studs to create a substrate for vertical tile and attached horizontally to plywood for tile floors, kitchen counters and backsplashes. It can be used on the exterior of buildings as a base for exterior plaster (stucco) systems and sometimes as the finish system itself.
Plaster veneer or plaster skim is a construction methodology for surfacing interior walls, by applying a thin layer of plaster over a substrate—typically over specially formulated gypsum board base, similar in nature to drywall.
A popcorn ceiling, also known as a stipple ceiling or acoustic ceiling, is a ceiling with one of a variety of spray-on or paint-on treatments. The bumpy surface is created by tiny particles of vermiculite or polystyrene, which gives the ceiling sound-deadening properties. Mixtures are available in fine, medium, and coarse grades.
Faux painting or faux finishing are terms used to describe decorative paint finishes that replicate the appearance of materials such as marble, wood or stone. The term comes from the French word faux, meaning false, as these techniques started as a form of replicating materials such as marble and wood with paint, but has subsequently come to encompass many other decorative finishes for walls and furniture including simulating recognisable textures and surfaces.
Cement render or cement plaster is the application of a mortar mix of sand and cement, and water to brick, concrete, stone, or mud brick. It is often textured, colored, or painted after application. It is generally used on exterior walls but can be used to feature an interior wall. Depending on the 'look' required, rendering can be fine or coarse, textured or smooth, natural or colored, pigmented or painted.
Plaster spraying allows a plasterer to skim a drywall more than five times faster than using a hand float to apply it. Although classic gypsum-based plaster can be sprayed if it is "spray grade," most plaster sprayers prefer the organic-based pre-mixed plaster packaged in a plastic bag because the plaster spraying machine does not need to be cleaned out after the job is finished, providing that plaster is kept moist. The pre-mixed plaster also has the advantage that any surplus can be recycled, almost eliminating waste, and plasterers do not need to haul water and mix the plaster from powder. A drywall skimmed with pre-mixed plaster can be painted in less than 24 hours, depending on the ambient temperature and humidity.
Fiberglass mesh is a neatly woven, crisscross pattern of fiberglass thread that is used to create new products such as tape and filters. When it is used as a filter, it is not uncommon for the manufacturer to spray a PVC coating to make it stronger and last longer. The most common place to find fiberglass mesh is in tape products.
Acoustic plaster is plaster which contains fibres or aggregate so that it absorbs sound. Early plasters contained asbestos, but newer ones consist of a base layer of absorptive substrate panels, which are typically mineral wool, or a non-combustible inorganic blow-glass granulate. A first finishing layer is then applied on top of the substrate panels, and sometimes a second finishing layer is added for greater sound attenuation. Pre-made acoustic panels are more commonly used, but acoustic plaster provides a smooth and seamless appearance, and greater flexibility for readjustment. The drawback is the greater level of skill required in application. Proprietary types of acoustic plaster developed in the 1920s included Macoustic Plaster, Sabinite, Kalite, Wyodak, Old Newark and Sprayo-Flake produced by companies such as US Gypsum.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
