Kristi Company

Last updated
Kristi KT-7, #004, only known successful KT7 produced, shown in restored condition Kristi-KT7-side-view.jpg
Kristi KT-7, #004, only known successful KT7 produced, shown in restored condition

Kristi snowcats were 1950s/1960s tracked vehicles suitable for snow and other terrain and produced originally in Colorado and then later in Washington.

Contents

Propeller drive snowplane

Homebuilt snowplane from the 1930s pre-dating the Kristi concept snowplane illustrating traditional rigid skis Homebuilt-Snowplane,-1930's.jpg
Homebuilt snowplane from the 1930s pre-dating the Kristi concept snowplane illustrating traditional rigid skis
Early drawing showing tilting concept on a snowplane prior to the switch to snowcat construction KristiSnowplane.jpg
Early drawing showing tilting concept on a snowplane prior to the switch to snowcat construction
1963 Polaris snowplane, like other non-Kristi designs, did not use the "Christie" ski action, this results in the rear skis skidding across the snow surface through turns Snowplane-POLARIS-1963.jpg
1963 Polaris snowplane, like other non-Kristi designs, did not use the "Christie" ski action, this results in the rear skis skidding across the snow surface through turns

The original Kristi snowplanes [1] were very similar to the earlier Russian Aerosledges which were developed as early as World War I. The Kristi design was more advanced than the Aerosledges, and utilized adjustable ski action to perform higher speed turns and received a patent for its design in 1955.

According to the introduction, contained in the operators manual: "The development of the Kristi snow vehicles began in early 1947 in the form of a very unusual snow plane. This propeller driven vehicle utilized a control by which the operator could tilt the machine from side to side, in effect raising one ski and lowering the other to negotiate up to 45-degree side slopes and permit high-speed turns without skidding. This tilting and edging of skis after the manner of a skier was called "Ski-Action". Since it could do a "Christie" up or down hill, the trade name "Kristi" was adopted."[ citation needed ]

The Kristi snowplane featured a revolutionary change in ski handling concepts. As stated in the manual, the design was inspired by snow skiers who angled their skis to effect a turn (this angling of skis is called a Christie) and it allows for both higher speed turns and greater control. The theoretical advantage of the Kristi system in a snowplane would make for safer and faster turns on frozen lakes. The photos of snowplanes clearly show stationary mounted rear skis and a turning front ski, the Kristi design improved on this design by allowing the skis to carve their edges into the snow as traditional snowplanes's rear skis will skid laterally during a turn.

The major advancement of the Kristi tilt ski system apparently made no impact on the commercial or amateur snowplane industry as it did not appear to be used in practical application. Perhaps because of the mechanical complexity of the original design, no snowplanes are known to exist that employ the "Christi Ski Action" concept.[ citation needed ] Snowplanes are well suited to travel on frozen lakes and snowcovered fields or roads but are not suitable for use in mountains or on rough ground.

Track drive snowcat

Kristi adjustable track concept Patent-Document-2967578.jpg
Kristi adjustable track concept

Early in the life of the company, Kristi switched production from snowplanes to snowcats. The Kristi had a unique ability to raise or lower its tracks individually which had the effect of raising one side of the vehicle to keep the vehicle level while crossing side slopes. [2] Further, the front or rear of both tracks could be raised or lowered so the snowcat's cabin could remain level while climbing or descending slopes. [3]

Kristi was commercially built in Colorado. The original Kristi company offered 3 basic models, the KT2, KT3 and KT4. Total production of all the units combined, over the entire 12 year life of the original company's lifespan, was lower than 1 year of production of other commercial snowcats. The company changed ownership and moved to Washington and continued production. Production was always on a small scale, and the products were innovative. The KT7 was designed and produced after the sale of the company and after it moved to Washington. It is possible that additional KT2, KT3 and KT4 units were manufactured by the new owners in Washington state but it is unlikely since the designs had not been substantially upgraded by the time the new owners purchased the company. A slightly smaller version of the KT3 was called the KT2. Both the KT2 and KT3 were powered by Volkswagen air-cooled 4-cylinder engines, it is reported that a small percentage may have been powered by Porsche engines. The KT2 and KT3 shared mechanicals and even shared the same operators manual. The VW engine developed 32 horsepower.

An early KT3, still in commercial use to access mountaintop antenna arrays in need of repair Kristi at Microwave Array.jpg
An early KT3, still in commercial use to access mountaintop antenna arrays in need of repair
KT3 on a rare Kristi tilt trailer KristiKT3andKristiTrailer.jpg
KT3 on a rare Kristi tilt trailer

Kristi also built custom tilt-bed trailers used for hauling the KT3 which used the same tires and wheels on the trailer as on the KT3.

Various different sales brochures make different claims about the transmissions used in the Kristi KT3. It is therefore possible to find a KT3 with either 8 or 9 forward gears, and either 4 or 3 reverse gears. The units with 8 forward/4 reverse had a high-low range ratio of 7:1. All used joystick controls in a V-shaped arrangement that were centered under tachometer.

Specifications from the sales brochure for the Kristi KT3 stated that it was 11' long, 7'4" wide and had a height of 5'9" with an empty weight of 2095 pounds. The KT3 was configured for 5 passengers and imparted 0.46 PSI of pressure onto the snow. It had a maximum cargo/passenger capacity of 1,500 pounds and a towing capacity of 2000 pounds. With a fuel capacity of 20 gallons of gasoline, it claims 15 to 18 hours of operating time and a top speed of 20 mph.

The KT3 sales brochure claimed the ability to climb a 100% grade with full load when not on the snow. It claimed the ability to climb a 70% grade in snow conditions with a full load and in soft snow it claims the ability to traverse a side slope with a 60% grade. The Kristi action adjustable track suspension will hold the cabin level on slopes with up to a 25% grade.

KT3 pictured with Mt. Bradley in the background Kristi at Bradley1.jpg
KT3 pictured with Mt. Bradley in the background

A larger Kristi snowcat was produced and designated the KT4 and the KT4a. The KT4 had a fully enclosed fiberglass body while the KT4a was an open version and "a" designated that it was an amphibious unit capable of floating and crossing streams or ponds. The Kristi KT4a's prototype has been referred to as the "Water Walker" due to its amphibious capabilities. [4] The KT4 and KT4a units are very rare and less than 5 are known to exist of a total production that was probably under 20. The KT4 was powered by a Chevrolet Corvair 6-cylinder gasoline engine.

A prototype model built on a modified Chevrolet 1/2 ton pick-up truck frame was built and designated the KWT. This unit still exists and is in storage. The KWT, according to the prototype's announcement pre-sales brochure, was built for ranchers and farmers as a heavy duty all terrain vehicle capable of hauling and towing loads into remote snowbound locations. It also was designed to be capable to be driven on the road with the tracks removed. The KWT never reached the production. The engine specified was to be a 250-cubic-inch, or optionally a 292-cubic-inch, 6-cylinder gasoline powered, Chevrolet engine. A brochure announces it would use conventional steering when driven as a wheeled vehicle but does not indicate how it would steer as a tracked vehicle. This prototype vehicle still exists and is currently unused and in storage and owned by a private antique vehicle collector.

Yetti Edition Kristi KT7 after 1+ year restoration Kristi-KT7-yetti.jpg
Yetti Edition Kristi KT7 after 1+ year restoration

Washington relocation and the KT7

Kristi eventually changed ownership and moved to Washington state. The later model KT3s were equipped with a 53 hp VW engine, or alternately with a Porsche engine. The top speeds of the KT3 were 20 mph when powered by the VW engine, and 25 mph when powered by the Porsche engine. [5] Kristi of Washington developed a new model called the KT7 snowcat, The most refined and last produced of the Kristi snowcats was the KT7, of which only 4 were built and only 1 was successful: #002. The KT7 used a Ford Anglia gasoline engine controlled by governor over hydrostatic Vickers drive with body tilt. The industrial engine has a 104 cu.in V-4 configuration generating 80 hp. While never produced, the brochure also offered a V-6, 171 cu.in. engine as an option. The engine was mounted in the middle of the snowcat with the driver and front passenger forward, and the rear passengers aft, facing the rear. There were access doors on either end of the KT7 and the rear and the front look nearly identical save for the headlamps. An early original brochure announcing the KT7 actually shows its designation as a KT3a and calls it an "improved KT3" but the production brochure has it designated as the KT7. The KT7 was tested by the FAA for use in Alaska but failed to achieve a 20 mph speed requirement; the sales brochure claims a 15 to 25 mph speed "depending on transmission/engine options." Photos of the only known restored (by Allen Huston) KT7 Yetti are posted on this page, this unit is the last KT7 produced and is serial #002 owned and preserved by Marco Johnson of Bellingham, Washington, it is also the only unit that was modestly successful.

According to an original sales brochure, specifications for the KT7 indicate it was 12'1" long, was 8'2" wide to the outside of the tracks, and had a body width of 4'1" and a height of 5'6" tall with the body in the lowered position and 6'4" tall with the body in the raised position. Ground clearance in the raised position is 16" and the weight is 3225# with a rated load of 1800#. Climbing performance is "Up to 100% depending on the terrain surface conditions."

Demise

Kristi was technically interesting, but the company failed to produce quantities of snowcats to compete with other North American or European snowcat manufacturers. The FAA test failure doomed the KT7, and ultimately lead to the demise of the company in the early 1970s. While Kristi was commercially unsuccessful, it did surpass other companies that only developed "snowplanes", largely because tracked vehicles are more suitable for uneven terrain.

See also

Related Research Articles

<span class="mw-page-title-main">Volkswagen Kübelwagen</span> Motor vehicle

The Volkswagen Type 82 Kübelwagen, or simply Kübel, contractions of the original German word Kübelsitzwagen, is a military light utility vehicle designed by Ferdinand Porsche and built by Volkswagen during World War II for use by the Nazi German military. Based heavily on the Volkswagen Beetle, it was prototyped and first deployed in Poland as the Type 62, but following improvements entered full-scale production as the Type 82. Several derivative models, such as the Kommandeurswagen, were also built in hundreds, or in dozens.

<span class="mw-page-title-main">Continuous track</span> System of vehicle propulsion

Continuous track or tracked treads are a system of vehicle propulsion used in tracked vehicles, running on a continuous band of treads or track plates driven by two or more wheels. The large surface area of the tracks distributes the weight of the vehicle better than steel or rubber tyres on an equivalent vehicle, enabling continuous tracked vehicles to traverse soft ground with less likelihood of becoming stuck due to sinking.

<span class="mw-page-title-main">Volkswagen Schwimmwagen</span> Amphibious transport

The Volkswagen Schwimmwagen is a light four-wheel drive amphibious car, used extensively by German ground forces during the Second World War. With over 15,000 units built, the Schwimmwagen is the most-produced amphibious car in history.

<span class="mw-page-title-main">Amphibious vehicle</span> Vehicle capable of transport on both land and over/under water

An amphibious vehicle is a vehicle that is a means of transport viable on land as well as on or under water. Amphibious vehicles include amphibious bicycles, ATVs, cars, buses, trucks, railway vehicles, combat vehicles and hovercraft.

<span class="mw-page-title-main">Volkswagen Golf</span> Small family cars manufactured by Volkswagen

The Volkswagen Golf is a compact car/small family car (C-segment) produced by the German automotive manufacturer Volkswagen since 1974, marketed worldwide across eight generations, in various body configurations and under various nameplates – including as the Volkswagen Rabbit in the United States and Canada, and as the Volkswagen Caribe in Mexico (Mk1).

<span class="mw-page-title-main">Snowmobile</span> Land vehicle designed for travel on snow

A snowmobile, also known as a snowmachine, motor sled, motor sledge, skimobile, or snow scooter, is a motorized vehicle designed for winter travel and recreation on snow.

<span class="mw-page-title-main">Oldsmobile Toronado</span> Motor vehicle

The Oldsmobile Toronado is a personal luxury car manufactured and marketed by the Oldsmobile division of General Motors from 1966 to 1992 over four generations. The Toronado was noted for its transaxle version of GM's Turbo-Hydramatic transmission, making it the first U.S.-produced front-wheel drive automobile since the demise of the Cord 810/812 in 1937.

<span class="mw-page-title-main">Bombardier Recreational Products</span> Canadian manufacturer of recreational vehicles

BRP Inc. is a Canadian manufacturer of snowmobiles, all-terrain vehicles, side by sides, motorcycles, and personal watercraft. It was founded in 2003, when the Recreational Products Division of Bombardier Inc. was spun off and sold to a group of investors consisting of Bain Capital, the Bombardier-Beaudoin family and the Caisse de dépôt et placement du Québec. Bombardier Inc., was founded in 1942 as L'Auto-Neige Bombardier Limitée by Joseph-Armand Bombardier at Valcourt in the Eastern Townships, Quebec.

<span class="mw-page-title-main">Half-track</span> Land vehicle with both regular wheels and continuous tracks

A half-track is a civilian or military vehicle with regular wheels at the front for steering and continuous tracks at the back to propel the vehicle and carry most of the load. The purpose of this combination is to produce a vehicle with the cross-country capabilities of a tank and the handling of a wheeled vehicle.

<span class="mw-page-title-main">Volkswagen New Beetle</span> Compact car

The Volkswagen New Beetle is a compact car, introduced by Volkswagen in 1997, drawing heavy inspiration from the exterior design of the original Beetle. Unlike the original Beetle, the New Beetle has its engine in the front, driving the front wheels, with luggage storage in the rear. It received a facelift in 2005 and was in production until 2011, almost fourteen years since its introduction.

<span class="mw-page-title-main">Tucker Sno-Cat</span> Family of tracked vehicles

The Tucker Sno-Cat is a family of tracked vehicles for snow conditions, manufactured in Medford, Oregon by the company of the same name.

<span class="mw-page-title-main">Snowcat</span> Enclosed-cab, truck-sized, fully tracked vehicle designed to move on snow

A snowcat is an enclosed-cab, truck-sized, fully tracked vehicle designed to move on snow. Major manufacturers are PistenBully (Germany), Prinoth (Italy), and Tucker.

<span class="mw-page-title-main">History of the automobile</span>

Crude ideas and designs of automobiles can be traced back to ancient and medieval times. In 1649, Hans Hautsch of Nuremberg built a clockwork-driven carriage. In 1672, a small-scale steam-powered vehicle was created; the first steam-powered automobile capable of human transportation was built by Nicolas-Joseph Cugnot in 1769. Inventors began to branch out at the start of the 19th century, creating the de Rivaz engine, one of the first internal combustion engines, and an early electric motor. Samuel Brown later tested the first industrially applied internal combustion engine in 1826. Only two of these were made.

<span class="mw-page-title-main">Honda Gyro</span> Type of motorcycle

The Honda Gyro is a family of small, three-wheeled motorcycles sold primarily in Japan, and often used for delivery or express service.

<span class="mw-page-title-main">Volkswagen SP2</span> Motor vehicle

The Volkswagen SP2 is a sports car that was developed by Volkswagen do Brasil and built from July 1972 until December 1975. It is based on the chassis of the Brazilian market Volkswagen Type 3. "SP" is said to be an initialism of São Paulo, where the car was built, or of "sports prototype". In its issue of 20 June 1973, German technology magazine Hobby called the SP2 the "most beautiful Volkswagen in the world".

<span class="mw-page-title-main">Snow coach</span>

A snow coach is a specialized passenger transport vehicle designed to operate over snow or ice, similar to a large, multi-passenger snowcat equipped with bus-style seating. These vehicles may have multiple sets of massive, low-pressure tires, or they may have tracks. Snow coaches may seat ten or more passengers and are often used for sightseeing tours or over-snow transportation.

<span class="mw-page-title-main">Snow Trac</span> Small Swedish snowcat

The Snow Trac is a small personal Snowcat that is roughly the size of a modern compact car. Aktiv Snow Trac were manufactured in Sweden between 1957 and 1981, with additional vehicles manufactured in Scotland.

<span class="mw-page-title-main">Volkswagen Golf Mk1</span> First generation of Golf compact car

The Volkswagen Golf Mk1 is the first generation of a small family car manufactured and marketed by Volkswagen. It was noteworthy for signalling Volkswagen's shift of its major car lines from rear-wheel drive and rear-mounted air-cooled engines to front-wheel drive with front-mounted, water-cooled engines that were often transversely-mounted.

<span class="mw-page-title-main">Logan Machine Company</span> Former American snowcat manufacturer

Logan Manufacturing Company was a US manufacturer of snowcats that ceased operation in 2000. LMC is both the tradename and an acronym.

<span class="mw-page-title-main">Winnebago LeSharo</span> Motor vehicle

The Winnebago LeSharo is a Class B (low-profile) recreational vehicle that was assembled by Winnebago Industries from 1983 to 1992. Though also using a cutaway van chassis like larger motorhomes, the LeSharo was designed to optimize fuel economy. Alongside its lower-roof exterior, the vehicle used the chassis of the front-wheel drive Renault Trafic commercial van. While the model line itself was not sold in North America, the Trafic shared its powertrain with several Renault and Jeep vehicles sold domestically.

References

  1. Kristi Snowplane design Patent #2,700,427 U.S. patent office granted 1-25-1955
  2. Arnold, Alan (July 1964) Volkswagen Foreign Car Guide
  3. Kristi adjustable suspension & drive system Patent #2,967,578 U.S. patent office granted 1-10-1961
  4. Crismon, Fred W. (2001) U.S. Military Tracked Vehicles Victory WW 2 Publishing ISBN   978-0970056719
  5. Kristi-Washington KT3 brochure