Mouli grater

Last updated

A Mouli grater or rotational grater is a hand-operated kitchen utensil designed for grating or pureeing small quantities of food. [1] The device consists of a small metal drum with holes that grate the food and a handle for turning the drum.

The hand-held unit consists of two sections with hinged handles. The end of one handle contains a food hopper with a grating cylinder and a crank for rotating the cylinder. The other section has a rounded surface that acts as a clamp, pressing the food to be grated into the grating cylinder. The hinged handles are held in one hand and squeezed so that the food presses against the grating cylinder. Meanwhile, the other hand turns the crank, causing the cylinder to rotate and the food to be grated. Because the cylinder can be removed, the Mouli grater can be easily used by both left- and right-handed people by simply placing the grater with the crank on the preferred side.

The rotational grater was first patented in France in the 1940s. Mouli is a French brand name that became Moulinex in 1957, [2] partly in response to the success of the electric coffee grinder of the same name. A grating cylinder similar to the one used in this design later turned up in food processors from that company.

There are three cylinders: a fine grater, medium grater, and a slice-producing cutter.

See also

Related Research Articles

Crankshaft Mechanism for converting reciprocating motion to rotation

A crankshaft is a shaft driven by a crank mechanism consisting of a series of cranks and crankpins to which the connecting rods of an engine is attached. It is a mechanical part able to perform a conversion between reciprocating motion and rotational motion. In a reciprocating engine, it translates reciprocating motion of the piston into rotational motion, whereas in a reciprocating compressor, it converts the rotational motion into reciprocating motion. In order to do the conversion between two motions, the crankshaft has "crank throws" or "crankpins", additional bearing surfaces whose axis is offset from that of the crank, to which the "big ends" of the connecting rods from each cylinder attach.

Valve Flow control device

A valve is a device or natural object that regulates, directs or controls the flow of a fluid by opening, closing, or partially obstructing various passageways. Valves are technically fittings, but are usually discussed as a separate category. In an open valve, fluid flows in a direction from higher pressure to lower pressure. The word is derived from the Latin valva, the moving part of a door, in turn from volvere, to turn, roll.

Action (firearms) Functional mechanism of breech-loading

In firearms terminology, an action is the functional mechanism of a breech-loading firearm that handles the ammunition cartridges, or the method by which that mechanism works. Actions are technically not present on muzzleloaders, as all those are single-shot firearms with a closed off breech with the powder and projectile manually loaded from the muzzle. Instead, the muzzleloader ignition mechanism is referred to as the lock.

Starter (engine) Device used to start an internal combustion engine

A starter is a device used to rotate (crank) an internal-combustion engine so as to initiate the engine's operation under its own power. Starters can be electric, pneumatic, or hydraulic. The starter can also be another internal-combustion engine in the case, for instance, of very large engines, or diesel engines in agricultural or excavation applications.

Hinge Mechanical bearing that connects two solid objects, typically allowing only a limited angle of rotation between them

A hinge is a mechanical bearing that connects two solid objects, typically allowing only a limited angle of rotation between them. Two objects connected by an ideal hinge rotate relative to each other about a fixed axis of rotation: all other translations or rotations being prevented, and thus a hinge has one degree of freedom. Hinges may be made of flexible material or of moving components. In biology, many joints function as hinges, like the elbow joint.

Bicycle pedal

The pedal is the part of a bicycle that the rider pushes with their foot to propel the vehicle. It provides the connection between the cyclist's foot or shoe and the crank allowing the leg to turn the bottom bracket spindle and propel the bicycle's wheels. A pedal usually consists of a spindle that threads into the end of the crank, and a body on which the foot rest is attached, that is free to rotate on bearings with respect to the spindle.

Crank (mechanism) Simple machine transferring motion to or from a rotaing shaft at a distance from the centreline

A crank is an arm attached at a right angle to a rotating shaft by which circular motion is imparted to or received from the shaft. When combined with a connecting rod, it can be used to convert circular motion into reciprocating motion, or vice versa. The arm may be a bent portion of the shaft, or a separate arm or disk attached to it. Attached to the end of the crank by a pivot is a rod, usually called a connecting rod (conrod).

Pencil sharpener Device for sharpening a pencils writing point by shaving away its worn surface

A pencil sharpener is a tool for sharpening a pencil's writing point by shaving away its worn surface. Pencil sharpeners may be operated manually or by an electric motor. It is common for many sharpeners to have a casing around them, which can be removed for emptying the pencil shavings debris into a rubbish/trash bin.

Can opener Device used to open metal cans

A can opener or tin opener is a mechanical device used to open tin cans. Although preservation of food using tin cans had been practiced since at least 1772 in the Netherlands, the first can openers were not patented until 1855 in England and 1858 in the United States. These early openers were basically variations of a knife, though the 1855 design continues to be produced. The first can opener, consisting of the now familiar sharp rotating cutting wheel that runs round the can's rim to cut open the lid, was invented in 1870, but was considered very difficult to operate for the ordinary consumer. A successful design came out in 1925 when a second, serrated wheel was added to hold the cutting wheel on the rim of the can. This easy-to-use design has become one of the most popular can opener models.

Connecting rod Piston engine component which connects the piston to the crankshaft

A connecting rod is the part of a piston engine which connects the piston to the crankshaft. Together with the crank, the connecting rod converts the reciprocating motion of the piston into the rotation of the crankshaft. The connecting rod is required to transmit the compressive and tensile forces from the piston. In its most common form, in an internal combustion engine, it allows pivoting on the piston end and rotation on the shaft end.

Grater Tool to grate something

A grater, also known as a shredder, is a kitchen utensil used to grate foods into fine pieces. The modern grater was invented by François Boullier in the 1540s, originally to grate cheese.

Breechblock

A breechblock is the part of the firearm action that closes the breech of a breech loading weapon before or at the moment of firing. It seals the breech and contains the pressure generated by the ignited propellant. Retracting the breechblock allows the chamber to be loaded with a cartridge.

Four-bar linkage

A four-bar linkage, also called a four-bar, is the simplest movable closed-chain linkage. It consists of four bodies, called bars or links, connected in a loop by four joints. Generally, the joints are configured so the links move in parallel planes, and the assembly is called a planar four-bar linkage. Spherical and spatial four-bar linkages also exist and are used in practice.

Mixer (appliance)

A mixer, depending on the type, also called a hand mixer or stand mixer, is a kitchen device that uses a gear-driven mechanism to rotate a set of "beaters" in a bowl containing the food or liquids to be prepared by mixing them.

Indexing head Dividing head

An indexing head, also known as a dividing head or spiral head, is a specialized tool that allows a workpiece to be circularly indexed; that is, easily and precisely rotated to preset angles or circular divisions. Indexing heads are usually used on the tables of milling machines, but may be used on many other machine tools including drill presses, grinders, and boring machines. Common jobs for a dividing head include machining the flutes of a milling cutter, cutting the teeth of a gear, milling curved slots, or drilling a bolt hole circle around the circumference of a part.

Moulinex

Moulinex is a Groupe SEB brand along with Rowenta, Calor, All-Clad, Lagostina, Krups, and Tefal, all household products brands. The company designed and produced the Mouli grater. The company was founded by Jean Mantelet who in 1932 invented the Moulin-Légumes, a hand-crank food mill for puréeing vegetables. The design is considered an early forerunner to the modern food processor.

Food mill Kitchen utensil for mashing and sieving soft foods

A food mill is a food preparation utensil for mashing and sieving soft foods. Typically, a food mill consists of three parts: a bowl, a bottom plate with holes like those in a colander, and a crank fitted with a bent metal blade that crushes the food and forces it through the holes in the plate. The bottom plate may be a permanent part of the device, or interchangeable plates with different hole sizes may be supplied. Three corrugated feet on the base, or two ears on the rim plus the handle, fit on the rim of a cooking pot and hold the mill in position over it.

Soap dispenser Device that dispenses soap

A soap dispenser is a device that, when manipulated or triggered appropriately, dispenses soap. It can be manually operated by means of a handle, or can be automatic. Soap dispensers are often found in public toilets.

Surform

A surform tool features perforated sheet metal and resembles a food grater. A surform tool consists of a steel strip with holes punched out and the rim of each hole sharpened to form a cutting edge. The strip is mounted in a carriage or handle. Surform tools were called "cheese graters" decades before they entered the market as kitchen utensils used to grate cheese. Surform planes have been described as a cross between a rasp and a plane.

Salad spinner

A salad spinner, also known as a salad tosser, is a kitchen tool used to wash and remove excess water from salad greens. It uses centrifugal force to separate the water from the leaves, enabling salad dressing to stick to the leaves without dilution.

References

  1. "What Is a Mouli Grater?". wiseGEEK. Retrieved January 9, 2012.
  2. "Moulinex S.A. -- Company History". Moulinex S.A. Retrieved January 9, 2012.