OTDOA

Last updated

OTDOA (Observed Time Difference Of Arrival) is a positioning feature introduced in rel9 E-UTRA (LTE radio). It's a multilateration method in which the User Equipment (UE) measures the time difference between some specific signals from several eNodeBs and reports these time differences to a specific device in the network (the ESMLC). The ESMLC based on these time differences and knowledge of the enodeBs locations calculates the UEs' position.

Contents

Background

In December 2008, due to regulatory requirements like the E911, which require that it should be possible to locate UEs with a certain accuracy, a work item was proposed in the 3GPP TSG-RAN42 meeting. [1] This proposed between others the study of the feasibility of OTDOA. OTDOA was meant to work in a similar way as the 3G IPL feature.

During the summer of 2009 the necessary changes to the RAN1 36.211, [2] 36.212, [3] 36.213 [4] and 36.214 [5] specifications were accepted. And a bit later the RAN4 [6] requirements and RAN2 [7] protocol related matters settled.

Technology

A OTDOA procedure works as follows: The ESMLC requests through the LPP layer an OTDOA measurement: a set of RSTD (Reference Signal Time Difference) measurements from the UE. Together with this request the UE receives assistance data. This assistance data, provides a list of cells (enodeBs), with their PRS (Positioning Reference Signal) parameters, including BW, periodicity etc.

The UE then proceeds to perform these measurements during a given period of time (typically up to 8 or 16 periods of the PRS signals). These measurements consist on estimating the exact time offsets between the PRS from different cells. Then it reports to the ESMLC these estimated time differences together with an estimate of the measurement quality.

The ESMLC then, using these time difference estimates, and the knowledge of the cells positions and transmit time offsets estimates the position of the UE.

The description of the LPP (LTE positioning protocol) can be found in the 36.355 specification. [7] The exact details of the PRS signals can be found in section 6.10.4 of the 36.211 specification. [2] And a simple OTDOA procedure can be found in the RAN5 OTDOA testcases' descriptions in section 9 of the 37.571-1 specification [8]

From a UE architecture perspective the LPP layer resides outside of the EUTRAN protocol stack, over NAS, but typically implemented in the cellular modem firmware. The UE RSTD measurements themselves would be performed by the L1 layer.

Adoption

OTDOA is an optional feature in the 3GPP LTE standard. This means that it is optional for networks and UEs to support it while still being deemed LTE compatible. Like with other similar optional features, interest by particular carriers depends on regulatory requirements, and for UE vendors in carrier's requirements, as major carriers run their own certification tests on UEs which aim at operating in their network. [9]

Related Research Articles

The Universal Mobile Telecommunications System (UMTS) is a third generation mobile cellular system for networks based on the GSM standard. Developed and maintained by the 3GPP, UMTS is a component of the International Telecommunication Union IMT-2000 standard set and compares with the CDMA2000 standard set for networks based on the competing cdmaOne technology. UMTS uses wideband code-division multiple access (W-CDMA) radio access technology to offer greater spectral efficiency and bandwidth to mobile network operators.

Medium access control Service layer in IEEE 802 network standards

In IEEE 802 LAN/MAN standards, the medium access control sublayer is the layer that controls the hardware responsible for interaction with the wired, optical or wireless transmission medium. The MAC sublayer and the logical link control (LLC) sublayer together make up the data link layer. Within the data link layer, the LLC provides flow control and multiplexing for the logical link, while the MAC provides flow control and multiplexing for the transmission medium.

In telecommunications networks, RANAP is a protocol specified by 3GPP in TS 25.413 and used in UMTS for signaling between the Core Network, which can be a MSC or SGSN, and the UTRAN. RANAP is carried over Iu-interface.

Multimedia Broadcast Multicast Services (MBMS) is a point-to-multipoint interface specification for existing 3GPP cellular networks, which is designed to provide efficient delivery of broadcast and multicast services, both within a cell as well as within the core network. For broadcast transmission across multiple cells, it defines transmission via single-frequency network configurations. The specification is referred to as Evolved Multimedia Broadcast Multicast Services (eMBMS) when transmissions are delivered through an LTE network. eMBMS is also known as LTE Broadcast.

RNSAP is a 3GPP signalling protocol responsible for communications between RNCs Radio Network Controllers defined in 3GPP specification TS 25.423. It is carried on the lur interface and provides functionality needed for soft handovers and SRNS relocation. It defines signalling between RNCs, including SRNC and DRNC.

 SRNC | DRNC  | IUR |  RNSAP | RNSAP  | | |
E-UTRA

E-UTRA is the air interface of 3rd Generation Partnership Project (3GPP) Long Term Evolution (LTE) upgrade path for mobile networks. It is an acronym for Evolved Universal Mobile Telecommunications System (UMTS) Terrestrial Radio Access, also referred to as the 3GPP work item on the Long Term Evolution (LTE) also known as the Evolved Universal Terrestrial Radio Access (E-UTRA) in early drafts of the 3GPP LTE specification. E-UTRAN is the initialism of Evolved UMTS Terrestrial Radio Access Network and is the combination of E-UTRA, user equipment (UE), and E-UTRAN Node B or Evolved Node B (eNodeB).

Packet Data Convergence Protocol (PDCP) is specified by 3GPP in TS 25.323 for UMTS, TS 36.323 for LTE and TS 38.323 for 5G. PDCP is located in the Radio Protocol Stack in the UMTS/LTE/5G air interface on top of the RLC layer.

The Radio Resource Control (RRC) protocol is used in UMTS, LTE and 5G on the Air interface. It is a layer 3 protocol used between UE and Base Station. This protocol is specified by 3GPP in TS 25.331 for UMTS, in TS 36.331 for LTE and in TS 38.331 for 5G New Radio. RRC messages are transported via the PDCP-Protocol.

System Architecture Evolution (SAE) is the core network architecture of mobile communications protocol group 3GPP's LTE wireless communication standard.

LTE Advanced Mobile communication standard

LTE Advanced is a mobile communication standard and a major enhancement of the Long Term Evolution (LTE) standard. It was formally submitted as a candidate 4G to ITU-T in late 2009 as meeting the requirements of the IMT-Advanced standard, and was standardized by the 3rd Generation Partnership Project (3GPP) in March 2011 as 3GPP Release 10.

International Mobile Telecommunications-Advanced are the requirements issued by the ITU Radiocommunication Sector (ITU-R) of the International Telecommunication Union (ITU) in 2008 for what is marketed as 4G mobile phone and Internet access service.

A Home eNodeB, or HeNB, is the 3GPP's term for an LTE femtocell or Small Cell.

TR-196 is a Broadband Forum technical specification. Its official title is "Femto Access Point Service Data Model." The purpose of this Technical Report is to specify the Data Model for the Femto Access Point (FAP) for remote management purposes using the TR-069 CWMP.

The UMTS channels are communication channels used by third generation (3G) wireless Universal Mobile Telecommunications System (UMTS) networks. UMTS channels can be divided into three levels:

E-UTRAN Node B, also known as Evolved Node B, is the element in E-UTRA of LTE that is the evolution of the element Node B in UTRA of UMTS. It is the hardware that is connected to the mobile phone network that communicates directly wirelessly with mobile handsets (UEs), like a base transceiver station (BTS) in GSM networks.

Long-Term Evolution (LTE) telecommunications networks use several frequency bands with associated bandwidths.

Enhanced Cell ID, E-CellID, or E-CID is a positioning feature introduced in rel9 E-UTRA. The UE reports to the network (ESMLC) the serving cell ID, the timing advance and the IDs, estimated timing and power of the detected neighbor cells. The enodeB may report extra information to the ESMLC like the angle of arrival. The ESMLC estimates the UE position based on this information and its knowledge of the cells positions.

QoS Class Identifier (QCI) is a mechanism used in 3GPP Long Term Evolution (LTE) networks to ensure carrier traffic is allocated appropriate Quality of Service (QoS). Different carrier traffic requires different QoS and therefore different QCI values. QCI value 9 is typically used for the default carrier of a UE/PDN for non privileged subscribers.

Radio link control (RLC) is a layer 2 Radio Link Protocol used in UMTS, LTE and 5G on the Air interface. This protocol is specified by 3GPP in TS 25.322 for UMTS, TS 36.322 for LTE and TS 38.322 for 5G New Radio (NR). RLC is located on top of the 3GPP MAC-layer and below the PDCP-layer. The main tasks of the RLC protocol are:

Frequency bands for 5G New Radio, which is the air interface or radio access technology of the 5G mobile networks, are separated into two different frequency ranges. First there is Frequency Range 1 (FR1), which includes sub-6 GHz frequency bands, some of which are traditionally used by previous standards, but has been extended to cover potential new spectrum offerings from 410 MHz to 7125 MHz. The other is Frequency Range 2 (FR2), which includes frequency bands from 24.25 GHz to 52.6 GHz.

References

  1. ↑ Positioning Support for LTE
  2. 1 2 3GPP TS 36.211 E-UTRA Physical channels and modulation
  3. ↑ 3GPP TS 36.212 E-UTRA Multiplexing and channel coding
  4. ↑ 3GPP TS 36.213 E-UTRA Physical layer procedures
  5. ↑ 3GPP TS 36.214 E-UTRA Physical layer; Measurements
  6. ↑ E-UTRA Requirements for support of radio resource management
  7. 1 2 E-UTRA LTE Positioning Protocol (LPP)
  8. ↑ 3GPP TS 37.571-1 E-UTRA UE conformance specification; for UE positioning; Part 1: Conformance test specification
  9. ↑ ATT certification
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.