Orangeburg pipe

Last updated
Orangeburg pipe, showing its characteristic delamination in layers of compressed oil tar pitch-impregnated ground wood fibers Orangeburg Pipe.jpg
Orangeburg pipe, showing its characteristic delamination in layers of compressed oil tar pitch-impregnated ground wood fibers

Orangeburg pipe (also known as "fiber conduit", "bituminous fiber pipe" or "Bermico" or "sand pipe") is bituminized fiber pipe used in the United States. It is made from layers of ground wood pulp fibers and asbestos fibres compressed with and bound by a water resistant adhesive then impregnated with liquefied coal tar pitch. [1] [2] It was used from the 1860s through the 1970s, when it was replaced by PVC pipe for water supply and ABS pipe for drain-waste-vent (DWV) applications. The name comes from Orangeburg, New York, the town in which most Orangeburg pipe was manufactured, largely by the Fiber Conduit Company. It changed its name to the Orangeburg Manufacturing Company in 1948.

Contents

History

The first known use of any fiber pipe was in an experimental water delivery line in the Boston, Massachusetts area. The pipeline, finished in 1867, measured 1.5 miles in length and was in use through 1927. Bituminized pipe was not in widespread commercial use until the late 19th century when it was used exclusively as electrical conduit. [1]

In 1893, Stephen Bradley, Sr. founded the Fiber Conduit Company in Orangeburg, New York. Bradley's neighboring Union Electric Company power plants used exhaust steam from their generators to dry lengths of fiber conduit before they were sealed with liquified coal tar pitch. In turn, the Fiber Conduit Company's conduits were used to run electrical wiring throughout numerous newly constructed buildings across the country for the next forty years. Bradley, along with several competitors, installed miles of the fiber electrical conduit in skyscrapers, such as the Empire State Building. [1]

The early 1900s brought tremendous expansion of the telephone, telegraph and electrical industries, along with subway construction along the eastern seaboard. This expansion in installation of electrical and telecommunications wiring within buildings and subway tunnels brought with it a rising demand for fiber conduit to run it in. In addition, fiber conduit was increasingly being used for underground ducting for distributing wires under streets and roads, particularly where they were being excavated to build subways, as well as along railroads. [1]

Fiber was next adopted by the booming oil industry to pump salt waste-water from drilling sites to treatment and disposal areas. During what ended up being trial usage of the Fiber Conduit Co.'s "Alkacid" line it was quickly discovered that while long-lived and incredibly durable in normal drainage operations, such pipe easily ruptured under pressure. The industry then shifted to more durable asbestos cement pipe. [1]

While a variety of companies competed with Fiber Conduit Co., including American (East Chicago, Indiana), J–M Fibre Conduit (Lockport, New York), Bermico (Brown Co. of Berlin, New Hampshire), and American (Fulton, New York), it was by far and away the industry leader in bituminized fiber conduit piping throughout the early 20th century and beyond. With cast iron in short supply during World War II demand sharply increased with the need for electrical conduit for use in new airfields and military bases. In 1948, the name of the Fiber Conduit Company was changed to the Orangeburg Manufacturing Company. During the postwar housing boom, the demand for cheap housing materials was at an all-time high and available drainage materials were scarce. Orangeburg Manufacturing produced a thicker-walled centrifugally-laminated pipe, sturdier for sewer and drain uses, which became known simply as "Orangeburg pipe". [1]

So rapidly did PVC and ABS overtake bituminized pipe in the 1970s that the Orangeburg Pipe Company closed by 1974. Countless thousands of miles of decaying bituminized pipe remain in use throughout the US, slowly being replaced by modern alternatives. [1]

Use

Orangeburg pipe was made of wood pulp sealed with liquified coal tar pitch in inside diameters from 2 inches to 18 inches, with a perforated version for leach fields. Joints were made of the same material, and, because of the residual stickiness of the coal tar, were sealed without adhesives. Orangeburg was inexpensive, lightweight, albeit brittle, and soft enough to be cut with a handsaw.

Orangeburg was a low cost alternative to metal for sewer lines in particular. Lack of strength causes pipes made of Orangeburg to fail more frequently than pipes made with other materials. The useful life for an Orangeburg pipe is about 50 years under ideal conditions, but has been known to fail in as little as 10 years. It has been taken off the list of acceptable materials by most building codes.

Related Research Articles

<span class="mw-page-title-main">Chemical industry</span> Industry (branch), which is engaged in the manufacturing of chemical products

The chemical industry comprises the companies and other organizations that develop and produce industrial, specialty and other chemicals. Central to the modern world economy, it converts raw materials into commodity chemicals for industrial and consumer products. It includes industries for petrochemicals such as polymers for plastics and synthetic fibers; inorganic chemicals such as acids and alkalis; agricultural chemicals such as fertilizers, pesticides and herbicides; and other categories such as industrial gases, speciality chemicals and pharmaceuticals.

<span class="mw-page-title-main">Thermoplastic</span> Plastic that softens with heat and hardens on cooling

A thermoplastic, or thermosoftening plastic, is any plastic polymer material that becomes pliable or moldable at a certain elevated temperature and solidifies upon cooling.

<span class="mw-page-title-main">Domtar</span> Largest integrated producer of uncoated free-sheet paper in North America

Domtar Corporation is a North American pulp and paper company that manufactures and markets wood fiber-based pulp and paper products. The company operates pulp mills and paper mills in Windsor, Quebec; Dryden, Ontario; Kamloops, British Columbia; Ashdown, Arkansas; Hawesville, Kentucky; Plymouth, North Carolina; Marlboro County, South Carolina; and Kingsport, Tennessee. While Domtar operated independently for several decades and was listed on the Toronto and New York stock exchanges, the company was acquired by Paper Excellence Group in November 2021 and has since operated as a subsidiary.

<span class="mw-page-title-main">Lamination</span> Technique of fusing layers of material

Lamination is the technique/process of manufacturing a material in multiple layers, so that the composite material achieves improved strength, stability, sound insulation, appearance, or other properties from the use of the differing materials, such as plastic. A laminate is a permanently assembled object created using heat, pressure, welding, or adhesives. Various coating machines, machine presses and calendering equipment are used.

<span class="mw-page-title-main">Oakum</span> Tarred fiber

Oakum is a preparation of tarred fibre used to seal gaps. Its main traditional applications were in shipbuilding, for caulking or packing the joints of timbers in wooden vessels and the deck planking of iron and steel ships; in plumbing, for sealing joints in cast iron pipe; and in log cabins for chinking. In ship caulking, it was forced into the seams using a hammer and a caulking iron, then sealed into place with hot pitch.

<span class="mw-page-title-main">Electrical wiring</span> Electrical installation of cabling

Electrical wiring is an electrical installation of cabling and associated devices such as switches, distribution boards, sockets, and light fittings in a structure.

<span class="mw-page-title-main">Power cable</span> Bundle of wires for transmitting electricity

A power cable is an electrical cable, an assembly of one or more electrical conductors, usually held together with an overall sheath. The assembly is used for transmission of electrical power. Power cables may be installed as permanent wiring within buildings, buried in the ground, run overhead, or exposed. Power cables that are bundled inside thermoplastic sheathing and that are intended to be run inside a building are known as NM-B.

<span class="mw-page-title-main">Flat roof</span> Type of roof

A flat roof is a roof which is almost level in contrast to the many types of sloped roofs. The slope of a roof is properly known as its pitch and flat roofs have up to approximately 10°. Flat roofs are an ancient form mostly used in arid climates and allow the roof space to be used as a living space or a living roof. Flat roofs, or "low-slope" roofs, are also commonly found on commercial buildings throughout the world. The U.S.-based National Roofing Contractors Association defines a low-slope roof as having a slope of 3 in 12 (1:4) or less.

<span class="mw-page-title-main">Vinyl composition tile</span> Flooring material

Vinyl composition tile (VCT) is a finished flooring material used primarily in commercial and institutional applications. Modern vinyl floor tiles and sheet flooring and versions of those products sold since the early 1980s are composed of colored polyvinyl chloride (PVC) chips formed into solid sheets of varying thicknesses by heat and pressure. Floor tiles are cut into modular shapes such 12-by-12-inch squares or 12-by-24-inch rectangles. In installation the floor tiles or sheet flooring are applied to a smooth, leveled sub-floor using a specially formulated vinyl adhesive or tile mastic that remains pliable. In commercial applications some tiles are typically waxed and buffed using special materials and equipment.

<span class="mw-page-title-main">High-density polyethylene</span> Class of polyethylenes

High-density polyethylene (HDPE) or polyethylene high-density (PEHD) is a thermoplastic polymer produced from the monomer ethylene. It is sometimes called "alkathene" or "polythene" when used for HDPE pipes. With a high strength-to-density ratio, HDPE is used in the production of plastic bottles, corrosion-resistant piping, geomembranes and plastic lumber. HDPE is commonly recycled, and has the number "2" as its resin identification code.

<span class="mw-page-title-main">Electrical tape</span> Adhesive electrical insulation

Electrical tape is a type of pressure-sensitive tape used to insulate electrical wires and other materials that conduct electricity. It can be made of many plastics, but PVC is most popular, as it stretches well and gives an effective and long lasting insulation. Electrical tape for class H insulation is made of fiberglass cloth.

Filament winding is a fabrication technique mainly used for manufacturing open (cylinders) or closed end structures. This process involves winding filaments under tension over a rotating mandrel. The mandrel rotates around the spindle while a delivery eye on a carriage traverses horizontally in line with the axis of the rotating mandrel, laying down fibers in the desired pattern or angle to the rotational axis. The most common filaments are glass or carbon and are impregnated with resin by passing through a bath as they are wound onto the mandrel. Once the mandrel is completely covered to the desired thickness, the resin is cured. Depending on the resin system and its cure characteristics, often the mandrel is autoclaved or heated in an oven or rotated under radiant heaters until the part is cured. Once the resin has cured, the mandrel is removed or extracted, leaving the hollow final product. For some products such as gas bottles, the 'mandrel' is a permanent part of the finished product forming a liner to prevent gas leakage or as a barrier to protect the composite from the fluid to be stored.

Vinyl coated polyester is a material frequently used for flexible fabric structures. It is made up of a polyester scrim, a bonding or adhesive agent, and an exterior PVC coating. The scrim supports the coating and provides the tensile strength, elongation, tear strength, and dimensional stability of the resulting fabric. Depending on its formula, the PVC coating makes the material waterproof and resistant to dirt, mildew, oil, salt, chemicals and UV rays and gives the material added strength and durability. It can be sewn or heat sealed by way of RF(Radio Frequency) welding or hot-air welding.

Pultrusion is a continuous process for manufacture of fibre-reinforced plastics with constant cross-section. The term is a portmanteau word, combining "pull" and "extrusion". As opposed to extrusion, which pushes the material, pultrusion pulls the material.

<span class="mw-page-title-main">Building insulation material</span>

Building insulation materials are the building materials that form the thermal envelope of a building or otherwise reduce heat transfer.

<span class="mw-page-title-main">Bituminous waterproofing</span> Roll roofing and waterproofing material

Bituminous waterproofing systems are designed to protect residential and commercial buildings. Bitumen is a material made up of organic liquids that are highly sticky, viscous, and waterproof. Systems incorporating bituminous-based substrates are sometimes used to construct roofs, in the form of "roofing felt" or "roll roofing" products.

<span class="mw-page-title-main">Asphalt roll roofing</span>

Asphalt roll roofing or membrane is a roofing material commonly used for buildings that feature a low sloped roof pitch in North America. The material is based on the same materials used in asphalt shingles; an organic felt or fiberglass mat, saturated with asphalt, and faced with granular stone aggregate. The installation process, known as Torch On Roofing, is often used on commercial properties in North America.

<span class="mw-page-title-main">Electrical conduit</span> Tube used to protect and route electrical wiring in a building or structure

An electrical conduit is a tube used to protect and route electrical wiring in a building or structure. Electrical conduit may be made of metal, plastic, fiber, or fired clay. Most conduit is rigid, but flexible conduit is used for some purposes.

HDPE pipe is a type of flexible plastic pipe used for the "transfer of fluid and gases, often used to replacing aging concrete or steel mains pipelines. Constructed from the thermoplastic HDPE, Its high impermeability and robust molecular bond make it suitable for high pressure pipelines. HDPE pipe is used across the globe for applications such as water mains, gas mains, sewer mains, slurry transfer lines, rural irrigation, fire system supply lines, electrical and communications conduit, and stormwater and drainage pipes.

References

  1. 1 2 3 4 5 6 7 Coal Tar Impregnated Wood Fibre Pipe", Jon C. Schladweiler, P.E., R.L.S.; Historian, 2004, sewerhistory.org
  2. ↑ "Risks and Problems: Orangeburg Pipe [Updated]". www.expresssewer.com. Archived from the original on 1 May 2022. Retrieved 15 May 2022.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.