The STM-4 (Synchronous Transport Module) is a SDHITU-Tfiber opticnetwork transmission standard. It has a bit rate of 622.080 Mbit/s.
The STM-4 specification is designed to carry 7,680 8-bit "voice" frames every 125 micro-seconds for a total payload bit rate of 491.520 Mbit/s. The other levels defined by the SDH standard are STM-1, STM-16, STM-64 and STM-256. Beyond this we have wavelength-division multiplexing (WDM) commonly used in submarine cabling.
Although STM-4 is comparable to OC-12 the SDH frame structure allocates more space to overhead than that of SONET. Because of this, STM-4's payload bandwidth differs from that of OC-12.
SDH Rates
SDH is a transport hierarchy based on multiples of 155.52 Mbit/s. The basic unit of SDH is STM-1.
Different SDH rates are given below:
STM-1 = 155.520 Mbit/s
STM-4 = 622.080 Mbit/s
STM-16 = 2,488.320 Mbit/s (~2.5 Gbit/second)
STM-64 = 9,953.280 Mbit/s (~10 Gbit/second)
STM-256 = 39,813.120 Mbit/s (~40 Gbit/second)
Each rate is an exact multiple of the lower rate, therefore the hierarchy is synchronous.
STM-1 frame structure
The basic STM-1 carrier frame consists of eight overheads, four pointers and a space for the payload. The overheads are the regeneration section overhead (RSOH), associated with the regenerators, and the multiplex section overhead (MSOH), associated with the multiplexers.
The space for the payload carries the VC-4 container, the first byte of which is signaled by the AU-4 pointer, and which is allowed to move in order to accommodate frequency
In previous sections we have looked at an example in which a 140 Mbit/s signal was mapped into a VC-4, but the multiplexing map lets the STM-1 signal transport other types of Plesiochronous signals and even combinations of signals. All the possibilities are shown in the table below:
Composition
2 Mbit/s
34 Mbit/s
140 Mbit/s
1x VC-4
0
0
1
3x VC-3
0
3
0
42xVC-12 + 1xVC-3
42
1
0
63xVC-12
63
0
0
The basic STM-1 transport rate is 155.520 Mbit/s and is defined in the ITU-T recommendation G.707.
As mentioned above, the overhead of an STM-4 signal (SOH) is divided into two parts: the MSOH and the RSOH. The overheads contain information from the system itself, which is used for a wide range of management functions, such as monitoring transmission quality, detecting failures, managing alarms, data communication channels, service channels, etc. These functions will be described in more detail in the section on network management services.
An STM-4 frame consists of 36 rows each containing 270 bytes. This is a direct multiple of STM-1, which consists of 9 rows each containing 270 bytes. The frame frequency of 32kHz has also been chosen as a 4x multiple of that of STM-1, so that one byte of frame corresponds to the transmission capacity of a 64 kbit/s channel.
The first 36 bytes of each row of a frame (with the exception of row 16) contain a Section OverHead. The first 36 bytes of row 16 contain the AU pointer (payload address). The field consisting of 261X36 bytes is for payload transmission (The STM payload is known as the Virtual Container (VC) and consists of the actual payload, known as the Container (C) and additional overhead known as Path Over Head (POH), for path related information).
The Virtual Container is not located rigidly in the frame but can move around freely in the payload section. The pointer indicates the position of the first byte of the VC (which is always the first byte of the POH). This allows a VC received in the multiplexer to be matched to a pre-specified frame phase of the STM-4.
Related Research Articles
Asynchronous Transfer Mode (ATM) is a telecommunications standard defined by American National Standards Institute (ANSI) and ITU-T for digital transmission of multiple types of traffic. ATM was developed to meet the needs of the Broadband Integrated Services Digital Network as defined in the late 1980s, and designed to integrate telecommunication networks. It can handle both traditional high-throughput data traffic and real-time, low-latency content such as telephony (voice) and video. ATM provides functionality that uses features of circuit switching and packet switching networks by using asynchronous time-division multiplexing.
Network throughput refers to the rate of successful message delivery over a communication channel, such as Ethernet or packet radio, in a communication network.The data that these messages contain may be delivered over physical or logical links, or through network nodes. Throughput is usually measured in bits per second, and sometimes in data packets per second or data packets per time slot.
The plesiochronous digital hierarchy (PDH) is a technology used in telecommunications networks to transport large quantities of data over digital transport equipment such as fibre optic and microwave radio systems. The term plesiochronous is derived from Greek plēsios, meaning near, and chronos, time, and refers to the fact that PDH networks run in a state where different parts of the network are nearly, but not quite perfectly, synchronized.
Synchronous optical networking (SONET) and synchronous digital hierarchy (SDH) are standardized protocols that transfer multiple digital bit streams synchronously over optical fiber using lasers or highly coherent light from light-emitting diodes (LEDs). At low transmission rates data can also be transferred via an electrical interface. The method was developed to replace the plesiochronous digital hierarchy (PDH) system for transporting large amounts of telephone calls and data traffic over the same fiber without the problems of synchronization.
A frame is a digital data transmission unit in computer networking and telecommunication. In packet switched systems, a frame is a simple container for a single network packet. In other telecommunications systems, a frame is a repeating structure supporting time-division multiplexing.
Time-division multiplexing (TDM) is a method of transmitting and receiving independent signals over a common signal path by means of synchronized switches at each end of the transmission line so that each signal appears on the line only a fraction of time in an alternating pattern. This method transmits two or more digital signals or analog signals over a common channel. It can be used when the bit rate of the transmission medium exceeds that of the signal to be transmitted. This form of signal multiplexing was developed in telecommunications for telegraphy systems in the late 19th century, but found its most common application in digital telephony in the second half of the 20th century.
In fiber-optic communications, wavelength-division multiplexing (WDM) is a technology which multiplexes a number of optical carrier signals onto a single optical fiber by using different wavelengths of laser light. This technique enables bidirectional communications over a single strand of fiber, also called wavelength-division duplexing, as well as multiplication of capacity.
In telecommunications and computing, bit rate is the number of bits that are conveyed or processed per unit of time.
Serial digital interface (SDI) is a family of digital video interfaces first standardized by SMPTE in 1989. For example, ITU-R BT.656 and SMPTE 259M define digital video interfaces used for broadcast-grade video. A related standard, known as high-definition serial digital interface (HD-SDI), is standardized in SMPTE 292M; this provides a nominal data rate of 1.485 Gbit/s.
The use of Asynchronous Transfer Mode (ATM) technology and services creates the need for an adaptation layer in order to support information transfer protocols, which are not based on ATM. This adaptation layer defines how to segment higher-layer packets into cells and the reassembly of these packets. Additionally, it defines how to handle various transmission aspects in the ATM layer.
Digital Signal 1 is a T-carrier signaling scheme devised by Bell Labs. DS1 is the primary digital telephone standard used in the United States, Canada and Japan and is able to transmit up to 24 multiplexed voice and data calls over telephone lines. E-carrier is used in place of T-carrier outside the United States, Canada, Japan, and South Korea. DS1 is the logical bit pattern used over a physical T1 line; in practice, the terms DS1 and T1 are often used interchangeably.
Throughput of a network can be measured using various tools available on different platforms. This page explains the theory behind what these tools set out to measure and the issues regarding these measurements.
The STM-1 is the SDH ITU-T fiber optic network transmission standard. It has a bit rate of 155.52 Mbit/s. Higher levels go up by a factor of 4 at a time: the other currently supported levels are STM-4, STM-16, STM-64 and STM-256. Above STM-256 wavelength-division multiplexing (WDM) is commonly used in submarine cabling.
Optical Carrier transmission rates are a standardized set of specifications of transmission bandwidth for digital signals that can be carried on Synchronous Optical Networking (SONET) fiber optic networks. Transmission rates are defined by rate of the bitstream of the digital signal and are designated by hyphenation of the acronym OC and an integer value of the multiple of the basic unit of rate, e.g., OC-48. The base unit is 51.84 Mbit/s. Thus, the speed of optical-carrier-classified lines labeled as OC-n is n × 51.84 Mbit/s.
Virtual concatenation (VCAT) is an inverse multiplexing technique creating a large capacity payload container distributed over multiple smaller capacity TDM signals. These signals may be transported or routed independently. Virtual concatenation has been defined for SONET/SDH, OTN and PDH path signals.
Ethernet Over SDH or Ethernet over SONET refers to a set of protocols which allow Ethernet traffic to be carried over synchronous digital hierarchy networks in an efficient and flexible way. The same functions are available using SONET.
ITU-T Recommendation G.709Interfaces for the Optical Transport Network (OTN) describes a means of communicating data over an optical network. It is a standardized method for transparent transport of services over optical wavelengths in DWDM systems. It is also known as Optical Transport Hierarchy (OTH) standard. The first edition of this protocol was approved in 2001.
In computer networking, an Ethernet frame is a data link layer protocol data unit and uses the underlying Ethernet physical layer transport mechanisms. In other words, a data unit on an Ethernet link transports an Ethernet frame as its payload.
The general communication channel (GCC) was defined by G.709 is an in-band side channel used to carry transmission management and signaling information within optical transport network elements.
ARINC 818: Avionics Digital Video Bus (ADVB) is a video interface and protocol standard developed for high bandwidth, low-latency, uncompressed digital video transmission in avionics systems. The standard, which was released in January 2007, has been advanced by ARINC and the aerospace community to meet the stringent needs of high performance digital video. The specification was updated and ARINC 818-2 was released in December 2013, adding a number of new features, including link rates up to 32X fibre channel rates, channel-bonding, switching, field sequential color, bi-directional control and data-only links.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
