Telescopic fork

Last updated November 07, 2023

A telescopic fork is a form of motorcycle front suspension whose use is so common that it is virtually universal. The telescopic fork uses fork tubes and sliders which contain the springs and dampers.

The main advantages of the telescopic fork are that it is simple in design and relatively cheap to manufacture and assemble, and that it is lighter than older designs using external components and linkage systems. Telescopic forks sometimes have gaiters to protect the fork tubes from abrasion and corrosion.

A more modern (and more expensive) version of the conventional telescopic fork is the inverted or "USD" (upside-down) fork.

BMW's patented telelever front suspension appears at first glance to be conventional telescopic fork, but the fork tubes contain neither springs nor damping. Instead, a wishbone and an inboard monoshock perform suspension duties, and the forks serve to locate the front wheel and control steering.^[1]

History

Early oil-damped telescopic fork on a 1939 BMW R12 R12-fork.jpg — Early oil-damped telescopic fork on a 1939 BMW R12

1968 BMW R60US with conventional telescopic fork Bmw-telescopic.jpg — 1968 BMW R60US with conventional telescopic fork

The first production motorcycles with hydraulically damped telescopic forks were the German BMW R12 and R17 in 1935.^[2] However, undamped telescopic forks were used on bikes made by The Scott Motorcycle Company from the beginning of production in 1908,^[3] and the Danish Nimbus used them from 1934 on.^[4]

Design

Conventional telescopic forks invariably have a pair of fork tubes, or "stanchions", at the top, clamped to a triple tree (also called a triple clamp or a yoke), and the sliders are at the bottom, attached to the front wheel spindle.

Inside most tubes are springs, fork oil, and air, creating a shock absorber. Some forks allow pressurized air to be added through a valve in the top of the fork to stiffen the suspension. Quality forks have a flexible air tube between both fork tubes in order to balance the air pressure in both forks. Modern fork tubes have a method which employs a screw to compress fork spring to increase or decrease spring pre-load.

Damping

Cartridge forks provide regressive damping. Self-contained cartridges within the forks contain spring-covered orifices regulating fork oil flow. The springs resist low forces and thus provide high damping rates. Higher forces compress the springs, allowing more oil flow and less damping. Thus the fork is stiffer when responding to small bumps but will soften as larger ones are encountered.

Most modern forks also are suspended on springs and control fork movement by damping through adjustable valving to control movement by controlling the flow of fork oil. The larger the orifice, the more free the flow and the less damped the fork. A selector atop the fork engages the desired hole size or valve and corresponding damping rate in compression, while usually the lower tube has a mechanism to control rebound (extension) damping.

Single action damping is currently being manufactured, such that compression occurs in one fork tube while its partner tube controls the rebound damping. This is because the oil controlling the damping in each tube, then, has only to control one direction of damping and is therefore less aerated by it working in both directions, and it develops less heat while working, which causes a variation to the thickness of the oil, thereby adversely affecting the damping rate.

Upside down

On some modern sport bikes and most off-road bikes, this system is inverted, with "sliders" complete with the spring/damper unit at the top, clamped to the yoke, while the stanchions are at the bottom. This is done (1) to reduce unsprung weight by having the heavier components suspended, and (2) to improve the strength and rigidity of the assembly by having the strong large-diameter "sliders" clamped in the yokes.^[5] The inverted system is referred to as an upside-down fork, or "USD" for short. One disadvantage of the USD design is that the entire reservoir of damping oil is above the slider seal so in case of leak the oil drains out, rendering any damping ineffective.

Triple tree

A triple tree ("triple clamp" (US) or "yoke" (UK)) attaches the fork tubes to the frame via steering head bearings, which allow the fork assembly to pivot from side to side, and therefore steer the motorcycle. Most bikes have upper and lower triple trees, providing two solid clamping points that keep the fork tubes parallel while also connecting the forks to the frame via the steering head bearings.

With the tendency to employ fork tubes with single action damping, fork triple trees need to be reinforced more than when the forks shared both damping roles, because the rigidity of the triple trees is relied upon to distribute the forces within the forks without flex.

The BMW Telever fork has only a single triple tree, which allows its fork sliders to be longer than those on telescopic forks. This in turn allows for greater overlap of the sliders over the stanchion tubes, which improves stiffness and helps to reduce flex.

Related Research Articles

A shock absorber or damper is a mechanical or hydraulic device designed to absorb and damp shock impulses. It does this by converting the kinetic energy of the shock into another form of energy which is then dissipated. Most shock absorbers are a form of dashpot.

<span class="mw-page-title-main">Nimbus (motorcycle)</span> Danish motorcycle

The Nimbus is a Danish motorcycle produced from 1919 to 1960 by Fisker and Nielsen of Copenhagen, Denmark, also manufacturers of "Nilfisk" brand vacuum cleaners. Two basic models were produced, both with a 750 cc four-cylinder engine.

A bicycle fork is the part of a bicycle that holds the front wheel.

The BMW R90S is a 900cc sport motorcycle produced by BMW from 1973 to 1976. BMW commissioned designer Hans Muth to oversee the R90S, which became the flagship of the boxer engined "/6" range. Sporting distinctive two-tone paintwork, a bikini fairing and a new tail, the R90S was intended to shrug off the enduring image of BMW bikes as staid and utilitarian.

The Killinger and Freund Motorcycle was an attempt in 1935 by a group of five German engineers from Munich to design a more streamlined and modified version of the German Megola front-wheel drive motorcycle. The work took three years to complete but the result was impressive. The engine displacement stayed the same as the Megola at 600 cc but was much lighter and more simplified than a standard 100 cc motorcycle of the time.

The Suzuki GSX-R750 is a sports motorcycle made by Suzuki since 1984. It was introduced at the Cologne Motorcycle Show in October 1984 as a motorcycle of the GSX-R series for the 1985 model year.

A motorcycle's suspension serves a dual purpose: contributing to the vehicle's handling and braking, and providing safety and comfort by keeping the vehicle's passengers comfortably isolated from road noise, bumps and vibrations.

<span class="mw-page-title-main">BMW R1200RT</span> Type of motorcycle

The BMW R1200RT is a touring or sport touring motorcycle that was manufactured from 2005 to 2019 by BMW Motorrad to replace the R1150RT model. It features a 1,170 cc (71 cu in) flat-twin engine with a six-speed gearbox and shaft drive.

<span class="mw-page-title-main">Motorcycle fork</span> Component of motorized two-wheelers

A motorcycle fork connects a motorcycle's front wheel and axle to its frame, typically via a yoke, also known as a triple clamp, which consists of an upper yoke joined to a lower yoke via a steering stem, a shaft that runs through the steering head, creating the steering axis. Most forks incorporate the front suspension and front brake, and allow the front wheel to rotate about the steering axis so that the bike may be steered. Most handlebars attach to the top clamp in various ways, while clip-on handlebars clamp to the fork tubes, either just above or just below the upper triple clamp.

Bicycle suspension is the system, or systems, used to suspend the rider and bicycle in order to insulate them from the roughness of the terrain. Bicycle suspension is used primarily on mountain bikes, but is also common on hybrid bicycles.

A motorcycle handlebar is a tubular component of a motorcycle's steering mechanism. Handlebars provide a mounting place for controls such as brake, throttle, clutch, horn, light switches and rear view mirrors; and they help to support part of the rider's weight. Even when a handlebar is a single piece it is usually referred to in the plural as handlebars.

<span class="mw-page-title-main">Steering damper</span> Device that helps dampen your steering from side to side

Originally designed in 1966 by Leonard R Jordan Jr, the steering damper or steering stabiliser is a damping device designed to inhibit an undesirable, uncontrolled movement or oscillation of a vehicle steering mechanism, a phenomenon known in motorcycling as the death wobble. The stabilizer absorbs unwanted energy in the side to side motion allowing the forks and shocks to work properly. Many things can cause a motorcycle chassis to get upset such as slamming on brakes, rough road, and lastly improper setup. An upset chassis can be a great deal of danger for the rider often times resulting in a crash. A steering stabilizer slows those movements down resulting in the rider feeling more comfortable on the motorcycle.

Motorcycle components and systems for a motorcycle are engineered, manufactured, and assembled in order to produce motorcycle models with the desired performance, aesthetics, and cost. The key components of modern motorcycles are presented below.

BMW S1000RR is a race oriented sport bike initially made by BMW Motorrad to compete in the 2009 Superbike World Championship, that is now in commercial production. It was introduced in Munich in April 2008, and is powered by a 999 cc (61.0 cu in) four-cylinder engine redlined at 14,200 rpm.

BMW Motorrad is the motorcycle brand and division of German automotive manufacturer, BMW. It has produced motorcycles since 1923, and achieved record sales for the fifth year in succession in 2015. With a total of 136,963 vehicles sold in 2015, BMW registered a growth of 10.9% in sales in comparison with 2014. In May 2011, the 2,000,000th motorcycle produced by BMW Motorrad was an R1200GS.

The BMW R1100RS is a sport-touring motorcycle that was manufactured by BMW Motorrad between 1993 and 2001, and was the first BMW motorcycle to use the R259 "Oilhead" boxer engine.

The BMW R1100S is a sports motorcycle that was manufactured by BMW Motorrad between 1998 and 2005. Introduced some 25 years after the R90S, the company's first sports bike, the R1100S was the first BMW bike having clip-on handlebars, rearset footrests and a removable cowl to cover the pillion seat. Producing nearly 100 hp, it has been described as a "sporty sports-tourer".

The BMW R nineT is a standard motorcycle made by BMW Motorrad since 2014. It is a retro styled roadster marketed by BMW to custom builders and enthusiasts as a "blank canvas for customizing".

The KTM 300 is a series of 2-stroke enduro / off-road motorcycles made by KTM. They are the Penton-inspired 1984 300 GS, the 300 DMX, the dirt only 300 MXC, European road legal 300 EXC and the US 300 XC (close-ratio), 300 XC-W and 300 SX (Motocross) versions. The KTM 300 is designed for difficult off-road conditions. The 300 EXC and the 300 XC-W have a small headlight, speedometer, tail-light and somewhat softer linkless PDS suspension. Starting in 2008 all 300's came with electric start. Since the early 2000s KTM has been offering the XC-W model in a special "Six-Days" or "ERZBERGRODEO" limited edition.

<span class="mw-page-title-main">KTM 200</span> Type of motorcycle

The KTM 200 consists of a series of two-stroke off-road enduro motorcycles made by KTM, the European, road legal 200 EXC, 200 MXC and the 200 XC-W for the US market being the last versions. The 200 attempts to combine the agility of a 125 cc class motorcycle with the power of a 250 cc. As a small bore enduro bike it is equipped with a wide-ratio gear box. Starting in 2013 all 200's came with electric start.

References

↑ Cossalter, V. "BMW Telelever and telescopic forks: which is better ?". Archived from the original on 2010-05-16. Retrieved 2012-04-07.
↑ Setright, L. J. K. (1977). Bahnstormer: The story of BMW Motor cycles. Transport Bookman Publications. p. 47. ISBN 0-85184-021-3.
↑ Wilson, Hugo (1995). "The A-Z of Motorcycles". The Encyclopedia of the Motorcycle . London: Dorling Kindersley. p. 166. ISBN 0-7513-0206-6. The advanced design included a two-speed gear, all-chain drive, a triangulated frame, telescopic forks, and a kickstarter.
↑ Duchene, Paul (May 2008). Duchene, Paul; Lombard, Stefan (eds.). "Bike Buys: Nimbus–The Prince of Denmark". Sports Car Market . Portland, OR USA: Sports Car Market. 20 (5): 136. ISSN 1527-859X . Retrieved 2012-12-30. Nimbus developed telescopic forks in 1933 and introduced hydraulic damping in 1939.
↑ Wilson, Hugo (1993). The Ultimate Motorcycle Book. Dorling-Kindersley. p. 181. ISBN 0-7513-0043-8.

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.

[Cossalter-1] Cossalter, V. "BMW Telelever and telescopic forks: which is better ?". Archived from the original on 2010-05-16. Retrieved 2012-04-07.

[2] Setright, L. J. K. (1977). Bahnstormer: The story of BMW Motor cycles. Transport Bookman Publications. p. 47. ISBN 0-85184-021-3.

[EncycloMoto166-3] Wilson, Hugo (1995). "The A-Z of Motorcycles". The Encyclopedia of the Motorcycle . London: Dorling Kindersley. p. 166. ISBN 0-7513-0206-6. The advanced design included a two-speed gear, all-chain drive, a triangulated frame, telescopic forks, and a kickstarter.

[SCMMay08-4] Duchene, Paul (May 2008). Duchene, Paul; Lombard, Stefan (eds.). "Bike Buys: Nimbus–The Prince of Denmark". Sports Car Market . Portland, OR USA: Sports Car Market. 20 (5): 136. ISSN 1527-859X . Retrieved 2012-12-30. Nimbus developed telescopic forks in 1933 and introduced hydraulic damping in 1939.

[UltiMoto181-5] Wilson, Hugo (1993). The Ultimate Motorcycle Book. Dorling-Kindersley. p. 181. ISBN 0-7513-0043-8.

[1]

[2]

[3]

[4]

[5]