Track stand

Last updated
A track stand Bicycle balancing.JPG
A track stand
A no-handed track stand Track stand Atlanta CM.jpg
A no-handed track stand

The track stand [1] or standstill [2] is a technique that bicycle riders can use to maintain balance while their bicycle remains stationary or moves only minimal distances. The technique originated in track cycling and is now used by other types of cyclists wishing to stop for a short time without putting a foot on the ground, such as bike commuters at stop signs. To perform a track stand, a cyclist holds the cranks in an approximately horizontal position with the front wheel steered to the left or right, and pedals forward, and back in the case of a fixed-gear bicycle, which the steered front wheel converts into a side-to-side motion.

Contents

Origin and use

The term originated from use of the technique by track cyclists [1] prior to starting, or as a tactic in track sprinting whereby riders will initially ride very slowly and maneuver across the track in an effort to get their rival to take the lead so that they can then draft (or slipstream) behind, conserving energy for the final sprint. [3]

Other types of cyclists also use the technique. [4] Commuters and bike messengers use it while stopped in traffic, especially at red lights, [1] mountain bikers use it in difficult terrain to determine a path and BMX cyclists use it in preparation for tricks. [4]

Technique

A cyclist executing a basic track stand holds the bicycle's cranks in a horizontal position, with their dominant foot forward. [4] Track stands executed on bicycles with a freewheel usually employ a small uphill section of ground. [1] The uphill needs to be sufficient to allow the rider to create backward motion by relaxing pressure on the pedals, thus allowing the bike to roll backwards. Once the track stand is mastered, even a very tiny uphill section is sufficient: e.g. the camber of the road, a raised road marking, and so on. [4] Where no such uphill exists, or even if the gradient is downhill, a track stand can be achieved on a freewheeling bicycle by using a brake to initiate a backwards movement. If a fixed-gear bicycle is being used, an uphill slope is not needed since the rider is able to simply back pedal to move backwards. In both cases forward motion is accomplished by pedalling forwards. The handlebars are held at approximately a 45-degree angle, converting the bike's forward and back motion into side-to-side motion beneath the rider's body. This allows the rider to keep the bike directly below his center of gravity. [5]

Those proficient at the track stand can maintain the position indefinitely. More difficult variations, mostly for show or track stand competitions, involve complications such as putting the non-dominant foot forward, sitting down, or taking one or both hands off the handlebars.

See also

Related Research Articles

<span class="mw-page-title-main">Bicycle</span> Pedal-driven two-wheel vehicle

A bicycle, also called a pedal cycle, bike, push-bike or cycle, is a human-powered or motor-assisted, pedal-driven, single-track vehicle, with two wheels attached to a frame, one behind the other. A bicycle rider is called a cyclist, or bicyclist.

<span class="mw-page-title-main">Track cycling</span> Bicycle racing sport

Track cycling is a bicycle racing sport usually held on specially built banked tracks or velodromes using purpose-designed track bicycles.

<span class="mw-page-title-main">Road bicycle</span> Bicycles designed for traveling at speed on paved roads

The term road bicycle is used to describe bicycles built for traveling at speed on paved roads. Some sources use the term to mean racing bicycle. Other sources specifically exclude racing bicycles from the definition, using the term to mean a bicycle of a similar style but built more for endurance and less the fast bursts of speed desired in a racing bicycle; as such, they usually have more gear combinations and fewer hi-tech racing features. Certain of these bicycles have been referred to as 'sportive' bicycles to distinguish them from racing bicycles.

<span class="mw-page-title-main">Tandem bicycle</span> Type of bicycle

A tandem bicycle or twin is a form of bicycle designed to be ridden by more than one person. The term tandem refers to the seating arrangement, not the number of riders. Patents related to tandem bicycles date from the mid 1880s. Tandems can reach higher speeds than the same riders on single bicycles, and tandem bicycle racing exists. As with bicycles for single riders, there are many variations that have been developed over the years.

<span class="mw-page-title-main">Recumbent bicycle</span> Type of bicycle

A recumbent bicycle is a bicycle that places the rider in a laid-back reclining position. Some recumbent riders may choose this type of design for ergonomic reasons: the rider's weight is distributed comfortably over a larger area, supported by back and buttocks. On a traditional upright bicycle, the body weight rests entirely on a small portion of the sitting bones, the feet, and the hands.

<span class="mw-page-title-main">Penny-farthing</span> Early type of bicycle

The penny-farthing, also known as a high wheel, high wheeler or ordinary, is an early type of bicycle. It was popular in the 1870s and 1880s, with its large front wheel providing high speeds, owing to it travelling a large distance for every rotation of the wheel. These bicycles had solid rubber tires and as a consequence the only shock absorption was in the saddle.

<span class="mw-page-title-main">Crankset</span> Bicycle part

The crankset or chainset is the component of a bicycle drivetrain that converts the reciprocating motion of the rider's legs into rotational motion used to drive the chain or belt, which in turn drives the rear wheel. It consists of one or more sprockets, also called chainrings or chainwheels attached to the cranks, arms, or crankarms to which the pedals attach. It is connected to the rider by the pedals, to the bicycle frame by the bottom bracket, and to the rear sprocket, cassette or freewheel via the chain.

<span class="mw-page-title-main">Bicycle pedal</span> Bicycle part which the rider pushes with their foot to turn the wheels

The pedal is the part of a bicycle that the rider pushes with their foot to propel the vehicle. It provides the connection between the cyclist's foot or shoe and the crank allowing the leg to turn the bottom bracket spindle and propel the bicycle's wheels. A pedal usually consists of a spindle that threads into the end of the crank, and a body on which the foot rest is attached, that is free to rotate on bearings with respect to the spindle.

Indoor cycling, often called spinning, is a form of exercise with classes focusing on endurance, strength, intervals, high intensity and recovery, and involves using a special stationary exercise bicycle with a weighted flywheel in a classroom setting. When people took cycling indoors in the late 19th century, whether for reasons of weather or convenience, technology created faster, more compact and efficient machines over time. The first iterations of the stationary bike ranged from the vertical Gymnasticon to regular bicycles on rollers.

<span class="mw-page-title-main">Racing bicycle</span> Bicycle designed for competitive road cycling

A racing bicycle, also known as a road bike is a bicycle designed for competitive road cycling, a sport governed by and according to the rules of the Union Cycliste Internationale (UCI).

<span class="mw-page-title-main">Fixed-gear bicycle</span> Bicycle that has a drivetrain with no freewheel mechanism

A fixed-gear bicycle is a bicycle that has a drivetrain with no freewheel mechanism such that the pedals always will spin together with the rear wheel. The freewheel was developed early in the history of bicycle design but the fixed-gear bicycle remained the standard track racing design. More recently the "fixie" has become a popular alternative among mainly urban cyclists, offering the advantage of simplicity compared with the standard multi-geared bicycle.

<span class="mw-page-title-main">Bunny hop (cycling)</span> Bicycle trick

The bunny hop (mountain biking) or bunnyhop is a bicycle trick typically used in mountain bikes or BMX bikes that allows the rider to launch their bike into the air as if jumping off a ramp. The pedals on the bicycle stick to the riders feet as the bike becomes airborne with the clipless pedals that have clips. The pedals on the bicycle seem to stick to the rider's feet as the bike becomes airborne, much like how a skateboard seems to stick to the feet of the skater performing an ollie. While the bunny hop can be quite challenging to learn, once mastered it gives riding opportunities for both BMX and mountain bike rider alike.

<span class="mw-page-title-main">Freestyle BMX</span> Cycle sport

Freestyle BMX is bicycle motocross stunt riding on BMX bikes. It is an extreme sport descended from BMX racing that consists of five disciplines: street, park, vert, trails, and flatland. In June 2017, the International Olympic Committee announced that freestyle park was to be added as an Olympic event to the 2020 Summer Olympics.

<span class="mw-page-title-main">Flatland BMX</span>

Flatland is a freestyle BMX riding style performed on smooth flat surfaces that do not include any ramps, jumps, or grindrails. It is sometimes described as a form of artistic cycling with a blend of breakdancing.

<span class="mw-page-title-main">Glossary of cycling</span> Bicycling terminology guide

This is a glossary of terms and jargon used in cycling, mountain biking, and cycle sport.

<span class="mw-page-title-main">Bicycle saddle</span> One of 5 contact points on an upright bicycle

A bicycle saddle, sometimes called a bicycle seat, is one of five contact points on an upright bicycle, the others being the two pedals and the two handles on the handlebars. The bicycle saddle has been known as such since the bicycle evolved from the draisine, a forerunner of the bicycle. It performs a similar role as a horse's saddle, not bearing all the weight of the rider as the other contact points also take some of the load.

<span class="mw-page-title-main">Rowing cycle</span>

A rowing cycle is a wheeled vehicle propelled by a rowing motion of the body. Steering, braking, and shifting are usually done by the handlebars. Feet are on symmetrical foot rests, as opposed to rotating pedals. Unlike many rowing boats, the rider faces forward. Rowing cycles exist in numerous designs, particularly with respect to frames and drive mechanisms. Commercial production numbers for rowing cycles are small compared to that of standard bicycles.

<span class="mw-page-title-main">Bicycle drivetrain systems</span> Systems used to transmit power to bicycles and other human-powered vehicles

Bicycle drivetrain systems are used to transmit power on bicycles, tricycles, quadracycles, unicycles, or other human-powered vehicles from the riders to the drive wheels. Most also include some type of a mechanism to convert speed and torque via gear ratios.

References

  1. 1 2 3 4 "Track Stand". Bicycling Magazine . Retrieved 2012-02-11. The track stand, named for the ability of velodrome racers to balance their fixed-gear bikes on the track, can help you stay upright without unclipping, and it lets you take off quickly.
  2. "UCI Cycling Regulations: Track Races" (PDF). UCI . Retrieved 2016-08-12. A maximum of two standstills shall be permitted for each race. The maximum period for a standstill shall be 30 seconds
  3. "Description of Track Events". Track Cycling Ireland. Archived from the original on 2008-08-01.
  4. 1 2 3 4 "Learn How To Track Stand". Team Estrogen. Retrieved 2012-02-10.
  5. Greg Goode. "Trackstands--Part Eleven of Fixed Gear 101". The Off Road Fixed Gear Site. Retrieved 2012-02-10.