Transfer stamping

Last updated
Stamping Process coil, blank, draw, trim, flange Stamping process overview, coil, blank, draw, trim, flange,KamConsulting.png
Stamping Process coil, blank, draw, trim, flange

Sheet metal forming in medium-high volume production environments is often completed through the use of a Transfer Press operating a number of dies as a complete system. Each die in the system is responsible for adding more shape to the part until the metal work piece attains its final shape. What makes transfer stamping unique is that a single press operates a number of tools, the movement of the sheet metal work piece from one operation to the next is performed by automation either built into the press or onto the dies. With each closing of the press the entire system of tools will close, each performing its designed work to the sheet metal. Upon opening the built in transfer mechanism moves the workpiece from one operation to the next in the sequence.

Contents

3 die stamping process in a single transfer press Sequence of dies in a transfer press, Draw, trim, flange, KamConsultant.jpg
3 die stamping process in a single transfer press

In the past these operations may have been performed using individual presses and the workpieces may have been moved from press to press, and die to die, by hand. As Automation improved hand loading was replaced by pick and place automation and by robots. The transfer press is a natural extension of this practice, simplifying the operation by having all tools in a single large press and using automation which is specifically designed for the press operations. [1]

Transfer mechanisms


Tri-axis transfer

Named for the movement of the transfer mechanism, tri-axis transfer mechanisms motion is defined by the three (3) axes of movement made by the part manipulators each press stroke. On the press downstroke the automation which will likely be holding the work piece will lower the work piece to the tool and retract to leave the part on the tool. At the bottom of the stroke the automation mechanism in the retracted state will cycle backward one pitch to position itself adjacent to the next workpiece. As the press cycles upward the part manipulators will index inward to pick up the next work piece, continuing upward following the press ram, then indexing forward to next station. As the press reaches the top of its stroke, the process repeats. The three axes of motion are up-down, in-out, and forward-back.

Cross-bar transfer

With a cross bar transfer mechanism, the in-out axes of movement is constrained by an automation bar spanning the die space. Commonly mounted with suction cups, this cross bar will pick the workpiece up from above and release the part, dropping it into place at the next station. With only two axes of motion and the automation spanning the die space, the cross bar transfer mechanism must "dwell" between adjacent tools between each press stroke.

Related Research Articles

Machine tool using energy to perform an intended action

A machine is a mechanical structure that uses power to apply forces and control movement to perform an intended action. Machines can be driven by animals and people, by natural forces such as wind and water, and by chemical, thermal, or electrical power, and include a system of mechanisms that shape the actuator input to achieve a specific application of output forces and movement. They can also include computers and sensors that monitor performance and plan movement, often called mechanical systems.

Lathe machine tool which rotates the workpiece on its axis

A lathe is a machine that rotates a workpiece about an axis of rotation to perform various operations such as cutting, sanding, knurling, drilling, deformation, facing, and turning, with tools that are applied to the workpiece to create an object with symmetry about that axis.

Forging manufacturing process involving the shaping of metal

Forging is a manufacturing process involving the shaping of metal using localized compressive forces. The blows are delivered with a hammer or a die. Forging is often classified according to the temperature at which it is performed: cold forging, warm forging, or hot forging. For the latter two, the metal is heated, usually in a forge. Forged parts can range in weight from less than a kilogram to hundreds of metric tons. Forging has been done by smiths for millennia; the traditional products were kitchenware, hardware, hand tools, edged weapons, cymbals, and jewellery. Since the Industrial Revolution, forged parts are widely used in mechanisms and machines wherever a component requires high strength; such forgings usually require further processing to achieve a finished part. Today, forging is a major worldwide industry.

Shaper

A shaper is a type of machine tool that uses linear relative motion between the workpiece and a single-point cutting tool to machine a linear toolpath. Its cut is analogous to that of a lathe, except that it is (archetypally) linear instead of helical.

Machining process in which a piece of raw material is cut into a desired final shape and size by a controlled material-removal process; manufacturing process

Machining is any of various processes in which a piece of raw material is cut into a desired final shape and size by a controlled material-removal process. The processes that have this common theme, controlled material removal, are today collectively known as subtractive manufacturing, in distinction from processes of controlled material addition, which are known as additive manufacturing. Exactly what the "controlled" part of the definition implies can vary, but it almost always implies the use of machine tools.


A die is a specialized tool used in manufacturing industries to cut or shape material mostly using a press. Like molds, dies are generally customized to the item they are used to create. Products made with dies range from simple paper clips to complex pieces used in advanced technology.

Drilling cutting process that uses a drill bit to cut a hole of circular cross-section in solid materials

Drilling is a cutting process that uses a drill bit to cut a hole of circular cross-section in solid materials. The drill bit is usually a rotary cutting tool, often multi-point. The bit is pressed against the work-piece and rotated at rates from hundreds to thousands of revolutions per minute. This forces the cutting edge against the work-piece, cutting off chips and your stuff is harder uno what i mean (swarf) from the hole as it is drilled. it drills holes.

Sheet metal metal formed by an industrial process into thin, flat pieces

Sheet metal is metal formed by an industrial process into thin, flat pieces. Sheet metal is one of the fundamental forms used in metalworking and it can be cut and bent into a variety of shapes. Countless everyday objects are fabricated from sheet metal. Thicknesses can vary significantly; extremely thin sheets are considered foil or leaf, and pieces thicker than 6 mm (0.25 in) are considered plate steel or "structural steel."

Punch press machine tool for punching

A punch press is a type of machine press used to cut holes in material. It can be small and manually operated and hold one simple die set, or be very large, CNC operated, with a multi-station turret and hold a much larger and complex die set.

Turning machining technique acting on rotated objects

Turning is a machining process in which a cutting tool, typically a non-rotary tool bit, describes a helix toolpath by moving more or less linearly while the workpiece rotates.

Metal lathe lathe designed for precisely machining relatively hard materials

A metal lathe or metalworking lathe is a large class of lathes designed for precisely machining relatively hard materials. They were originally designed to machine metals; however, with the advent of plastics and other materials, and with their inherent versatility, they are used in a wide range of applications, and a broad range of materials. In machining jargon, where the larger context is already understood, they are usually simply called lathes, or else referred to by more-specific subtype names. These rigid machine tools remove material from a rotating workpiece via the movements of various cutting tools, such as tool bits and drill bits.

Punching metal forming process that uses a punch press to force a tool, called a punch, through the workpiece to create a hole via shearing

Punching is a forming process that uses a punch press to force a tool, called a punch, through the workpiece to create a hole via shearing. Punching is applicable to a wide variety of materials that come in sheet form, including sheet metal, paper, vulcanized fibre and some forms of plastic sheet. The punch often passes through the work into a die. A scrap slug from the hole is deposited into the die in the process. Depending on the material being punched this slug may be recycled and reused or discarded.

Boring (manufacturing) process of enlarging a hole that has already been drilled

In machining, boring is the process of enlarging a hole that has already been drilled by means of a single-point cutting tool, such as in boring a gun barrel or an engine cylinder. Boring is used to achieve greater accuracy of the diameter of a hole, and can be used to cut a tapered hole. Boring can be viewed as the internal-diameter counterpart to turning, which cuts external diameters.

Press brake

A press brake is a machine pressing tool for bending sheet and plate material, most commonly sheet metal. It forms predetermined bends by clamping the workpiece between a matching punch and die.

Shearing, also known as die cutting, is a process which cuts stock without the formation of chips or the use of burning or melting. Strictly speaking, if the cutting blades are straight the process is called shearing; if the cutting blades are curved then they are shearing-type operations. The most commonly sheared materials are in the form of sheet metal or plates, however rods can also be sheared. Shearing-type operations include: blanking, piercing, roll slitting, and trimming. It is used in metalworking and also with paper and plastics.

Planing is a manufacturing process of material removal in which the workpiece reciprocates against a stationary cutting tool producing a plane or sculpted surface. Planing is analogous to shaping. The main difference between these two processes is that in shaping the tool reciprocates across the stationary workpiece. Planing motion is the opposite of shaping. Both planing and shaping are rapidly being replaced by milling.

Four-slide

A four-slide, also known as a multislide, multi-slide, or four-way, is a metalworking machine tool used in the high-volume manufacture of small stamped components from bar or wire stock. The press is most simply described as a horizontal stamping press that uses cams to control tools. The machine is used for progressive or transfer stamping operations.

There are many types of shears used to shear sheet metal.

Milling (machining) machining process

Milling is the process of machining using rotary cutters to remove material by advancing a cutter into a workpiece. This may be done varying direction on one or several axes, cutter head speed, and pressure. Milling covers a wide variety of different operations and machines, on scales from small individual parts to large, heavy-duty gang milling operations. It is one of the most commonly used processes for machining custom parts to precise tolerances.

Rule based DFM analysis for forging. Forging is the controlled deformation of metal into a specific shape by compressive forces. The forging process goes back to 8000 B.C. and evolved from the manual art of simple blacksmithing. Then as now, a series of compressive hammer blows performs the shaping or forging of the part. Modern forging uses machine driven impact hammers or presses which deform the work-piece by controlled pressure.

References

  1. Kam, Eric (2013). The Self-Proclaimed-Die-Expert Coloring and activity book. CreateSpace Independent Publishing Platform. pp. 3, 5. ISBN   978-1481985314.