Turboglide

Last updated

The Turboglide is a Chevrolet constant torque, continuously variable automatic transmission [1] first offered as an option on Chevrolet V8 passenger cars for 1957. It consisted of a turbine-driven planetary gearbox with a 'switch pitch' dual-pitch torque converter stator. It had a die-cast aluminum transmission case, like Packard's Ultramatic of 1956. Turboglide cost about $50 more than the Powerglide 2-speed automatic. It was available in all V8-powered 1957-1961 Chevrolet models except the Corvette. General Motors produced 646,000 of these transmissions during its production. [2]

Contents

Concept

The Turboglide was modeled along the lines of the concurrently-geared (as opposed to sequentially-geared) Buick Flight Pitch Dynaflow transmission,[ citation needed ] and operated very similarly. Using a five-element torque converter (pump, 3 turbines; low, intermediate, and direct ranges, and a dual stator), the Turboglide offered very smooth operation, as no shift occurred between ranges and hence there was no disruption in the flow of power. Concurrently-spinning turbines, each geared for the same torque multiplication as a different gear in a 3-speed unit, overlapped in effectively varying total power multiplication on a continuous basis. [3] For extra acceleration at any road speed, the stator vanes could be directed to a steeper angle which raised the stall speed of the torque converter and increased torque multiplication, as well as directing the oil flow at the turbine for the next-lower range. The selector quadrant order was Park, Reverse, Neutral, Drive, Hill Retarder (early 1957 only) as P  R N D Hr [4] or Grade Retarder (late 1957-1961) as P  R N D Gr. Some owners of the early 1957 models with the Turboglide transmission marked with HR [Hill Retarder] mistook the HR to mean High Range so the marking was changed early in the model year to Gr [Grade Retarder].[ citation needed ]

Operation

The basis of the Turboglide's unique abilities was its five-element torque converter. Most automatic transmissions have a three-element torque converter, consisting of an impeller (an engine-driven pump); a turbine that rotates with the flywheel; a transmission-driven turbine that receives the energy of the oil propelled by the impeller, and a stator that redirects the recirculating oil so that it strikes the back side of impeller blades to assist the engine rotation and to recapture energy from the fast-moving oil. The stator is one of two things that gives to the torque converter its torque multiplication ability, allowing it to reduce the ratio for increasing the torque when the turbine is rotating slower than the pump, the other being the angles of the pump and turbine blades.

In most automatic transmissions, the drive turbine only functions as an input to the transmission, where the power is redirected to gears in its automatic gearbox. The Turboglide differs by using three individual drive turbines, each connected to a different ratio inside the gearbox. Oil leaving the pump first strikes the turbine connected to the low (first gear) ratio. The design of the turbine permits oil to pass through its blades and strike the next turbine in line, the one connected to the intermediate (second gear) ratio, which receives some of the energy remaining in the oil flow. After leaving the intermediate turbine, the oil is passed to the direct (third gear) turbine which is direct drive at drive shaft speed. As the car starts from rest, the low turbine, which has the greatest gear reduction ratio, is relatively easy to bring up to match pump (engine) speed and the car starts from rest easily and accelerates quickly. While this occurs, the intermediate turbine receives an ever increasing share of the energy from the pump, as the Low turbine moves faster and oil passes more freely through it. Eventually, the low turbine matches pump speed, and the low turbine freewheels on a one-way sprag clutch much like on a bicycle. At this point, the intermediate turbine is carrying the majority of the drive force, and some energy is being sent to the direct turbine from the oil passing through the intermediate turbine as it also begins to match pump speed. Eventually, the intermediate turbine also matches pump speed, and the oil passes freely through low and intermediate turbines to drive the direct turbine alone, in direct drive (1:1 ratio). Because of the overlapping power input in different ratios, there is no 'shift' or sequential gearing, rather there is a concurrent geared drive, in effect the car starts out in 1-2-3, eventually drops 1 to be in 2-3 and eventually drops 2 to be in 3 alone.

The stator element of the torque converter has two blade positions, controlled by the driver via the accelerator pedal to offer a 'passing gear' and extra response at any speed from heavy throttle application. In normal driving the stator blades are arranged at 'cruise' angle which offers improved efficiency and response at light throttle. Flooring the accelerator pedal changes the angle of the stator vanes hydraulically to 'performance angle' which permits the converter to achieve stall about 1000 rpm higher than in 'cruise' as well as redirecting oil to strike the next-lower drive turbine which effectively lowers the drive ratio of the transmission and allows engine speed to rise for greater output.

Because of its unique operating characteristics, the Turboglide does not require large changes in engine RPM even with very large differences in car speed or desired engine output. In fact, accelerating from rest, the engine speed remains nearly constant (with no movement of the accelerator), even as the vehicle accelerates. The actual engine speed is a function of the pressure applied to the accelerator. One interesting effect during acceleration is the audible transition from the first gear turbine (occurring about two seconds after takeoff with moderate throttle), then progressing through the remaining two turbines which were not so audible. A similar effect occurs with some stepped-gear automatic transmissions, in which the first gear has a characteristic whine not present in higher gears.

At full throttle, the Turboglide will maintain the engine RPM within a narrow (~400 rpm) span of speed around 3500-4000 rpm where the best engine output is maintained, and the car will accelerate with a strong slingshot effect to catch up as the ratios drop imperceptibly as the car speed increases along the road. The effect is very similar to that of a jet aircraft during the take-off phase, since the engine maintains a strong high speed and the car accelerates, smoothly and strongly, from rest to maximum. In the normal light traffic driving, the Turboglide automatically selects the highest (the lowest numerically) practical ratio, and the engine speeds run in the 1000-2500 rpm range, saving fuel and improving the throttle response of the car to the small pedal motions. The 'Grade Retarder' range was to provide engine braking when necessary, a driving condition which could absorb close to 200 hp (150 kW) of power above to what was available via the engine compression, by counter-rotating the turbines in the converter and soaking up the vehicle energy by agitating the oil inside the converter housing. No low range was provided with Turboglide, as in the Drive range the ratio was always automatically and perfectly matched to the requirements of the operator (all ranges being always engaged, low and intermediate would freewheel on the 'sprag-clutches' as needed), and with the Grade Retarder providing a very efficient engine brake.

According to the Chevrolet manual[ which? ], above 65mph at wide open throttle, the torque converter begins to act as a hydraulic coupling, once the third turbine becomes fully engaged and no multiplication of torque occurs. So at speeds higher than 65mph, the Turboglide acts as if engaged in top gear, while below that speed, torque multiplication changes imperceptibly.

Continuously Variable Transmissions (CVT) offer similar performance characteristics, though with a completely different mechanical principle.

History

The Turboglide was designed under the supervision of Frank Winchell, Ed Cole and Robert P. Benzinger at Chevrolet engineering. Although it offered remarkable performance and smoothness, the execution of the first 1957 units led to substantial customer complaints[ citation needed ] and the unit was continuously upgraded[ citation needed ] to improve its durability until it was discontinued in 1961. The 1959 Turboglide incorporated very significant changes intended to improve its durability, some of which were possible to retrofit to earlier versions.[ citation needed ] Some enthusiasts[ who? ] reported that Turboglide had better reliability when coupled with the smaller 283 cubic-inch Turbo-Fire V8, than with the big-block 348 Turbo-Thrust engine.[ citation needed ]

The Turboglide was not GM's first attempt at a mass-produced aluminum-case transmission.[ citation needed ] That was accomplished by the Detroit Transmission Division during development of the Model 315 Dual Coupling Hydra-Matic four speed transmission, which was brought to market for 1956 Cadillac, Oldsmobile and Pontiac models with great success.[ according to whom? ] Chevrolet did not have the benefit of Detroit Division's experience in aluminum case casting, and engineering errors were made, exacerbated by a lack of pre-production testing. As a result, there were many complaints of the aluminum case cracking from the transmission operating pressures.[ citation needed ] This is why customers of those vehicles called it the "Terribleglide" transmission.[ according to whom? ] GM continued to improve this and other areas of the transmission, but by 1961 the Turboglide was dropped from the GM lineup.

Notes

  1. Flory, Jr., J. "Kelly" (2008). American Cars, 1946-1959 Every Model Every Year. McFarland & Company, Inc., Publishers. ISBN   978-0-7864-3229-5.
  2. "The Mysterious Pile Of 1950s Transmissions Buried At The Site Of An Old GM Plant". Jalopnik. 2018-06-25. Retrieved 2022-06-18.
  3. Winchell, F.; Route, W.; Kelley, O. (1958). "SAE Transactions". SAE International. 66: 167–178. JSTOR   44554141.
  4. "Directory Index: Chevrolet/1957_Chevrolet/1957_Chevrolet_Owners_Manual". Oldcarbrochures.com. Retrieved 2022-08-18.

Related Research Articles

Automatic transmission Type of motor vehicle transmission that automatically changes gear ratio as the vehicle moves

An automatic transmission is a multi-speed transmission used in internal combustion engine-based motor vehicles that does not require any driver input to change forward gears under normal driving conditions. It typically includes a transmission, axle, and differential in one integrated assembly, thus technically becoming a transaxle.

Torque converter Fluid coupling that transfers rotating power from a prime mover to a rotating driven load

A torque converter is a type of fluid coupling that transfers rotating power from a prime mover, like an internal combustion engine, to a rotating driven load. In a vehicle with an automatic transmission, the torque converter connects the power source to the load. It is usually located between the engine's flexplate and the transmission. The equivalent location in a manual transmission would be the mechanical clutch.

Propulsion transmission Drivetrain transmitting propulsion power

Propulsion transmission is the mode of transmitting and controlling propulsion power of a machine. The term transmission properly refers to the whole drivetrain, including clutch, gearbox, prop shaft, differential, and final drive shafts. In the United States the term is sometimes used in casual speech to refer more specifically to the gearbox alone, and detailed usage differs. The transmission reduces the higher engine speed to the slower wheel speed, increasing torque in the process. Transmissions are also used on pedal bicycles, fixed machines, and where different rotational speeds and torques are adapted.

Engine braking occurs when the retarding forces within an engine are used to slow down a motor vehicle, as opposed to using additional external braking mechanisms such as friction brakes or magnetic brakes.

Hydramatic Automatic transmission by General Motors

Hydramatic is an automatic transmission developed by both General Motors' Cadillac and Oldsmobile divisions. Introduced in 1939 for the 1940 model year vehicles, the Hydramatic was the first mass-produced fully-automatic transmission developed for passenger automobile use.

TorqueFlite Automotive part

TorqueFlite is the trademarked name of Chrysler Corporation's automatic transmissions, starting with the three-speed unit introduced late in the 1956 model year as a successor to Chrysler's two-speed PowerFlite. In the 1990s, the TorqueFlite name was dropped in favor of alphanumeric designations, although the latest Chrysler eight-speed automatic transmission has revived the name.

Ultramatic was the trademarked name of the Packard Motor Car Company's automatic transmission introduced in 1949 and produced until 1954, at Packard's Detroit, Michigan East Grand Boulevard factory. It was produced thereafter from late 1954, thru 1956 at the new Packard "Utica" Utica, Michigan facility.

Dynaflow

Dynaflow was the trademarked name for a type of automatic transmission developed and built by General Motors Buick Motor Division from late 1947 to mid-1963. The Dynaflow, which was introduced for the 1948 model year only as an option on Roadmaster models, received some severe early testing in the M18 Hellcat tank destroyer, which were built in Buick's Flint Assembly plant during World War II. It was also used in the 1951 Le Sabre concept car.

Turbo-Hydramatic or Turbo Hydra-Matic is the registered tradename for a family of automatic transmissions developed and produced by General Motors. These transmissions mate a three-element turbine torque converter to a Simpson planetary geartrain, providing three forward speeds plus reverse.

The Powerglide is a two-speed automatic transmission designed by General Motors. It was available primarily on Chevrolet from January 1950 through 1973, although some Pontiac models also used this automatic transmission after the fire at the Hydra-Matic factory in 1953. Powerglides were used extensively on Pontiacs produced for the Canadian market with Chevrolet powertrains. They were also used with Nova engines in the DJ-5A Jeeps produced 1968-1970 by Kaiser-Jeep and widely used as delivery vehicles by the United States Post Office. When introduced on upper-level Chevrolet models in 1950, the Powerglide represented the first automatic transmission offered in a low-priced automobile; in contrast, Ford did not offer their automatic transmission until 1951, while Plymouth car buyers had to wait until 1954. The transmission was simple and very durable, which satisfied customers.

Roto Hydramatic was an automatic transmission built by General Motors and used on some Oldsmobile, Pontiac and Holden models from 1961–1965. It was based on the earlier, four-speed Hydramatic, but was more compact, providing only three forward speeds plus a small 8" fluid coupling with a stator inside of the fluid coupling. Oldsmobile, one of the users of this transmission, called the fluid couplings stator the "Accel-A-Rotor." The lightweight, aluminum-cased transmission was sometimes nicknamed the "Slim Jim." HydraMatic Division calls the Roto a four range, three gear HydraMatic.

Fluid coupling

A fluid coupling or hydraulic coupling is a hydrodynamic or 'hydrokinetic' device used to transmit rotating mechanical power. It has been used in automobile transmissions as an alternative to a mechanical clutch. It also has widespread application in marine and industrial machine drives, where variable speed operation and controlled start-up without shock loading of the power transmission system is essential.

The Super Turbine 300 was a two-speed automatic transmission built by General Motors. It was used in various Buick, Oldsmobile, and Pontiac models from 1964-1969. It was the same transmission marketed under different brand names by each division including ST-300 by Buick, Jetaway by Olds and simply Automatic by Pontiac.

The AOD is a four-speed automatic transmission, with the 4th gear as overdrive. Introduced in 1980, it was Ford's first four-speed automatic overdrive transmission. The gearset design is based on the Ford "X" automatic transmissions used during the 1950s, '60s, and '70s. The AOD replaced many of Ford's older transmissions such as the C4, C5, and light duty applications of the FMX.

A transmission control unit (TCU), also known as a transmission control module (TCM), or a gearbox control unit (GCU), is a type of automotive ECU that is used to control electronic automatic transmissions. Similar systems are used in conjunction with various semi-automatic transmissions, purely for clutch automation and actuation. A TCU in a modern automatic transmission generally uses sensors from the vehicle, as well as data provided by the engine control unit (ECU), to calculate how and when to change gears in the vehicle for optimum performance, fuel economy and shift quality.

Corvair Powerglide

Chevrolet Corvair Powerglide is a two-speed automatic transmission designed specially for the then all-new 1960 Chevrolet Corvair compact car that emerged in the fall of 1959 as Chevrolet's competitor in the then booming small car market. The Corvair was powered by a rear-mounted Chevrolet Turbo-Air 6 engine that necessitated a specially designed transaxle. Corvair Powerglide took the principles of the standard Chevrolet Powerglide and modified them to suit the rear-mounted powertrain location of the new Corvair. The Corvair used the Powerglide for all 10 years it was produced; from 1961 to 1963, Pontiac used a modified version of Corvair Powerglide it called 'TempesTorque' for its front-engine, rear-transaxle Tempest, LeMans and Tempest LeMans cars.

Turbo transmissions are hydrodynamic, multi-stage drive assemblies designed for rail vehicles using internal combustion engines. The first turbo-transmission was developed in 1932 by Voith in Heidenheim, Germany. Since then, improvements to turbo-transmissions have paralleled similar advances in diesel motors and today this combination plays a leading role worldwide, second only to the use of electrical drives.

Motorcycle transmission Transmission for motorcycle applications

A motorcycle transmission is a transmission created specifically for motorcycle applications. They may also be found in use on other light vehicles such as motor tricycles and quadbikes, go-karts, offroad buggies, auto rickshaws, mowers, and other utility vehicles, microcars, and even some superlight racing cars.

Voith DIWA

The Voith DIWA automotive transmission was designed by Voith primarily for city-buses and suburban buses. The transmission utilizes a Differential-Wandler (Converter) or DIWA which replaces two gears which would be used on a conventional transmission. Voith has designed many variations and generations of the Voith DIWA.

Car controls Car parts used to control the vehicle

Car controls are the components in automobiles and other powered road vehicles, such as trucks and buses, used for driving and parking.

References