Acoustic emission

Last updated
The dislocation mechanism of the AE act (event) during the nucleation of a microcrack in metals with body-centered cubic (bcc) lattice AE event.jpg
The dislocation mechanism of the AE act (event) during the nucleation of a microcrack in metals with body-centered cubic (bcc) lattice

Acoustic emission (AE) is the phenomenon of radiation of acoustic (elastic) waves in solids that occurs when a material undergoes irreversible changes in its internal structure, for example as a result of crack formation or plastic deformation due to aging, temperature gradients, or external mechanical forces.

Contents

In particular, AE occurs during the processes of mechanical loading of materials and structures accompanied by structural changes that generate local sources of elastic waves. This results in small surface displacements of a material produced by elastic or stress waves [1] generated when the accumulated elastic energy in a material or on its surface is released rapidly. [2] [3] [4]

The mechanism of emission of the primary elastic pulse AE (act or event AE) may have a different physical nature. The figure shows the mechanism of the AE act (event) during the nucleation of a microcrack due to the breakthrough of the dislocations pile-up (dislocation is a linear defect in the crystal lattice of a material) across the boundary in metals with a body-centered cubic (bcc) lattice under mechanical loading, as well as time diagrams of the stream of AE acts (events) (1) and the stream of recorded AE signals (2). [3] [4]

The AE method makes it possible to study the kinetics of processes at the earliest stages of microdeformation, dislocation nucleation and accumulation of microcracks. Roughly speaking, each crack seems to "scream" about its growth. This makes it possible to diagnose the moment of crack origin itself by the accompanying AE. In addition, for each crack that has already arisen, there is a certain critical size, depending on the properties of the material. [3] [4] Up to this size, the crack grows very slowly (sometimes for decades) through a huge number of small discrete jumps accompanied by AE radiation. After the crack reaches a critical size, catastrophic destruction occurs, because its further growth is already at a speed close to half the speed of sound in the material of the structure. Taking with the help of special highly sensitive equipment and measuring in the simplest case the intensity of dNa/dt (quantity per unit of time), as well as the total number of acts (events) of AE, Na, it is possible to experimentally estimate the growth rate, crack length and predict the proximity of destruction according to AE data. [3] [4]

The waves generated by sources of AE are of practical interest in structural health monitoring (SHM), quality control, system feedback, process monitoring, and other fields. In SHM applications, AE is typically used to detect, locate, [5] and characterise [6] damage.

Phenomena

Acoustic emission is the transient elastic waves within a material, caused by the rapid release of localized stress energy. An event source is the phenomenon which releases elastic energy into the material, which then propagates as an elastic wave. Acoustic emissions can be detected in frequency ranges under 1 kHz, and have been reported at frequencies up to 100 MHz, but most of the released energy is within the 1 kHz to 1 MHz range. Rapid stress-releasing events generate a spectrum of stress waves starting at 0 Hz, and typically falling off at several MHz.

The three major applications of AE techniques are: 1) source location – determine the locations where an event source occurred; 2) material mechanical performance – evaluate and characterize materials and structures; and 3) health monitoring – monitor the safe operation of a structure, for example, bridges, pressure containers, pipelines, etc.

More recent research has focused on using AE to not only locate but also to characterise the source mechanisms [6] such as crack growth, friction, delamination, matrix cracking, etc. This would give AE the ability to tell the end user what source mechanism is present and allow them to determine whether structural repairs are necessary.

Employing proper signal processing and analysis allows for the possibility to gain a deeper understanding of the elastic wave signals and their relation to processes occurring within structures.

A significant expansion of the capabilities and an increase in the reliability of the AE diagnostic method is provided by the use of statistical methods for analyzing random event streams (for example, the random Poisson stream model) [3] [4]

The frequency domain representation of a signal obtained through Fast Fourier transform (FFT) provides information about the signal's magnitude and frequency content. [7]

AE can be related to an irreversible release of energy. It can also be generated from sources not involving material failure, including friction, cavitation, and impact.

Uses

The application of acoustic emission to nondestructive testing of materials typically takes place between 20 kHz and 1 MHz. [8] Unlike conventional ultrasonic testing, AE tools are designed for monitoring acoustic emissions produced by the material during failure or stress, and not on the material's effect on externally generated waves. Part failure can be documented during unattended monitoring. The monitoring of the level of AE activity during multiple load cycles forms the basis for many AE safety inspection methods, that allow the parts undergoing inspection to remain in service. [9]

The technique is used, for example, to study the formation of cracks during the welding process, as opposed to locating them after the weld has been formed with the more familiar ultrasonic testing technique.

In materials under active stress, such as some components of an airplane during flight, transducers mounted in an area can detect the formation of a crack at the moment it begins propagating. A group of transducers can be used to record signals and then locate the precise area of their origin by measuring the time for the sound to reach different transducers.

Long-term continuous monitoring for acoustic emissions is valuable for detecting cracks forming in pressure vessels [10] [11] and pipelines transporting liquids under high pressures. Standards for the use of acoustic emission for nondestructive testing of pressure vessels have been developed by the ASME, ISO, and the European Community.

This technique is used for estimation of corrosion in reinforced concrete structures. [9] [12]

Currently, the AE method is actively used in the tasks of monitoring and diagnostics of objects of nuclear power engineering, aviation, rocket and space technology, railway transport, historical artifacts (for example, the Tsar Bell in the Moscow Kremlin), as well as other products and objects of responsible purpose. [13]

AE sensing can potentially be utilised to monitor the state of health of lithium-ion batteries, particularly in the detection and characterisation of parasitic mechano-electrochemical events, such as electrode electrochemical grinding, phase transitions, and gas evolution. The piezoelectric sensor is employed to receive acoustic signals released by battery materials during operation. [14]

In addition to nondestructive testing, acoustic emission monitoring has applications in process monitoring. Applications where acoustic emission monitoring has successfully been used include detecting anomalies in fluidized beds and end points in batch granulation.

See also

Related Research Articles

<span class="mw-page-title-main">Ultrasound</span> Sound waves with frequencies above the human hearing range

Ultrasound is sound with frequencies greater than 20 kilohertz. This frequency is the approximate upper audible limit of human hearing in healthy young adults. The physical principles of acoustic waves apply to any frequency range, including ultrasound. Ultrasonic devices operate with frequencies from 20 kHz up to several gigahertz.

<span class="mw-page-title-main">Medical ultrasound</span> Diagnostic and therapeutic technique

Medical ultrasound includes diagnostic techniques using ultrasound, as well as therapeutic applications of ultrasound. In diagnosis, it is used to create an image of internal body structures such as tendons, muscles, joints, blood vessels, and internal organs, to measure some characteristics or to generate an informative audible sound. The usage of ultrasound to produce visual images for medicine is called medical ultrasonography or simply sonography, or echography. The practice of examining pregnant women using ultrasound is called obstetric ultrasonography, and was an early development of clinical ultrasonography. The machine used is called an ultrasound machine, a sonograph or an echograph. The visual image formed using this technique is called an ultrasonogram, a sonogram or an echogram.

<span class="mw-page-title-main">Nondestructive testing</span> Evaluating the properties of a material, component, or system without causing damage

Nondestructive testing (NDT) is any of a wide group of analysis techniques used in science and technology industry to evaluate the properties of a material, component or system without causing damage. The terms nondestructive examination (NDE), nondestructive inspection (NDI), and nondestructive evaluation (NDE) are also commonly used to describe this technology. Because NDT does not permanently alter the article being inspected, it is a highly valuable technique that can save both money and time in product evaluation, troubleshooting, and research. The six most frequently used NDT methods are eddy-current, magnetic-particle, liquid penetrant, radiographic, ultrasonic, and visual testing. NDT is commonly used in forensic engineering, mechanical engineering, petroleum engineering, electrical engineering, civil engineering, systems engineering, aeronautical engineering, medicine, and art. Innovations in the field of nondestructive testing have had a profound impact on medical imaging, including on echocardiography, medical ultrasonography, and digital radiography.

In electrical engineering, partial discharge (PD) is a localized dielectric breakdown (DB) of a small portion of a solid or fluid electrical insulation (EI) system under high voltage (HV) stress. While a corona discharge (CD) is usually revealed by a relatively steady glow or brush discharge (BD) in air, partial discharges within solid insulation system are not visible.

<span class="mw-page-title-main">Tsar Bell</span> Worlds heaviest bell, cast in 1735

The Tsar Bell, also known as the Tsarsky Kolokol, Tsar Kolokol III, or Royal Bell, is a 6.14-metre-tall (20.1 ft), 6.6-metre-diameter (22 ft) bell on display on the grounds of the Moscow Kremlin. The bell was commissioned by Empress Anna Ivanovna, niece of Peter the Great.

Laser-ultrasonics uses lasers to generate and detect ultrasonic waves. It is a non-contact technique used to measure materials thickness, detect flaws and carry out materials characterization. The basic components of a laser-ultrasonic system are a generation laser, a detection laser and a detector.

<span class="mw-page-title-main">Ultrasonic testing</span> Non-destructive material testing using ultrasonic waves

Ultrasonic testing (UT) is a family of non-destructive testing techniques based on the propagation of ultrasonic waves in the object or material tested. In most common UT applications, very short ultrasonic pulse waves with centre frequencies ranging from 0.1-15 MHz and occasionally up to 50 MHz MHz, and occasionally up to 50 MHz, are transmitted into materials to detect internal flaws or to characterize materials. A common example is ultrasonic thickness measurement, which tests the thickness of the test object, for example, to monitor pipework corrosion and erosion. Ultrasonic testing is extensively used to detect flaws in welds.

<span class="mw-page-title-main">Scanning acoustic microscope</span>

A scanning acoustic microscope (SAM) is a device which uses focused sound to investigate, measure, or image an object. It is commonly used in failure analysis and non-destructive evaluation. It also has applications in biological and medical research. The semiconductor industry has found the SAM useful in detecting voids, cracks, and delaminations within microelectronic packages.

<span class="mw-page-title-main">Ultrasonic transducer</span> Acoustic sensor

Ultrasonic transducers and ultrasonic sensors are devices that generate or sense ultrasound energy. They can be divided into three broad categories: transmitters, receivers and transceivers. Transmitters convert electrical signals into ultrasound, receivers convert ultrasound into electrical signals, and transceivers can both transmit and receive ultrasound.

<span class="mw-page-title-main">Electromagnetic acoustic transducer</span>

Electromagnetic acoustic transducer (EMAT) is a transducer for non-contact acoustic wave generation and reception in conducting materials. Its effect is based on electromagnetic mechanisms, which do not need direct coupling with the surface of the material. Due to this couplant-free feature, EMATs are particularly useful in harsh, i.e., hot, cold, clean, or dry environments. EMATs are suitable to generate all kinds of waves in metallic and/or magnetostrictive materials. Depending on the design and orientation of coils and magnets, shear horizontal (SH) bulk wave mode, surface wave, plate waves such as SH and Lamb waves, and all sorts of other bulk and guided-wave modes can be excited. After decades of research and development, EMAT has found its applications in many industries such as primary metal manufacturing and processing, automotive, railroad, pipeline, boiler and pressure vessel industries, in which they are typically used for nondestructive testing (NDT) of metallic structures.

<span class="mw-page-title-main">Lamb waves</span>

Lamb waves propagate in solid plates or spheres. They are elastic waves whose particle motion lies in the plane that contains the direction of wave propagation and the direction perpendicular to the plate. In 1917, the English mathematician Horace Lamb published his classic analysis and description of acoustic waves of this type. Their properties turned out to be quite complex. An infinite medium supports just two wave modes traveling at unique velocities; but plates support two infinite sets of Lamb wave modes, whose velocities depend on the relationship between wavelength and plate thickness.

Thermographic inspection refers to the nondestructive testing (NDT) of parts, materials or systems through the imaging of the temperature fields, gradients and/or patterns ("thermograms") at the object's surface. It is distinguished from medical thermography by the subjects being examined: thermographic inspection generally examines inanimate objects, while medical thermography generally examines living organisms. Generally, thermographic inspection is performed using an infrared sensor.

Rayleigh waves are a type of surface acoustic wave that travel along the surface of solids. They can be produced in materials in many ways, such as by a localized impact or by piezo-electric transduction, and are frequently used in non-destructive testing for detecting defects. Rayleigh waves are part of the seismic waves that are produced on the Earth by earthquakes. When guided in layers they are referred to as Lamb waves, Rayleigh–Lamb waves, or generalized Rayleigh waves.

Non-contact ultrasound (NCU) is a method of non-destructive testing where ultrasound is generated and used to test materials without the generating sensor making direct or indirect contact with the test material or test subject. Historically this has been difficult to do, as a typical transducer is very inefficient in air. Therefore, most conventional ultrasound methods require the use of some type of acoustic coupling medium in order to efficiently transmit the energy from the sensor to the test material. Couplant materials can range from gels or jets of water to direct solder bonds. However, in non-contact ultrasound, ambient air is the only acoustic coupling medium.

<span class="mw-page-title-main">Atomic force acoustic microscopy</span>

Atomic force acoustic microscopy (AFAM) is a type of scanning probe microscopy (SPM). It is a combination of acoustics and atomic force microscopy. The principal difference between AFAM and other forms of SPM is the addition of a transducer at the bottom of the sample which induces longitudinal out-of-plane vibrations in the specimen. These vibrations are sensed by a cantilever and tip called a probe. The figure shown here is the clear schematic of AFAM principle here B is the magnified version of the tip and sample placed on the transducer and tip having some optical coating generally gold coating to reflect the laser light on to the photodiode.

<span class="mw-page-title-main">James H. Williams Jr.</span>

James Henry Williams Jr. is a mechanical engineer, consultant, civic commentator, and teacher of engineering. He is currently Professor of Applied Mechanics in the Mechanical Engineering Department at the Massachusetts Institute of Technology (MIT). He is regarded as one of the world's leading experts in the mechanics, design, fabrication, and nondestructive evaluation (NDE) of nonmetallic fiber reinforced composite materials and structures. He is also Professor of Writing and Humanistic Studies at MIT.

Active thermography is an advanced nondestructive testing procedure, which uses a thermography measurement of a tested material thermal response after its external excitation. This principle can be used also for non-contact infrared non-destructive testing (IRNDT) of materials.

A machine tool monitoring system is a flow of information and system processing in which the information selection, obtaining data, processing of information and decision making on the refined information are integrated. The aim of tool condition monitoring is to detect early the disturbances in the machining process and wear of machine tool components.

<span class="mw-page-title-main">Stress wave tomography</span>

Acoustic or stress wave tomography is a non-destructive measurement method for the visualization of the structural integrity of a solid object. It is being used to test the preservation of wood or concrete, for example. The term acoustic tomography refers to the perceptible sounds that are caused by the mechanical impulses used for measuring. The term stress wave tomography describes the measurement method more accurately.

<span class="mw-page-title-main">Microcracks in rock</span>

Microcracks in rock, also known as microfractures and cracks, are spaces in rock with the longest length of 1000 μm and the other two dimensions of 10 μm. In general, the ratio of width to length of microcracks is between 10−3 to 10−5.

References

  1. ↑ pacuk.co.uk website Archived December 27, 2011, at the Wayback Machine . Retrieved 2011-12-05.
  2. ↑ Sotirios J. Vahaviolos (1999). Acoustic Emission: Standards and Technology Update. Vol. STP-1353. Philadelphia, PA: ASTM International (publishing). p. 81. ISBN   978-0-8031-2498-1.
  3. 1 2 3 4 5 Builo S. I. Physical, Mechanical and Statistical Aspects of Acoustic Emission Diagnostics // Physics and Mechanics of New Materials and Their Applications, New York: Nova Science Publishers, 2013. pp. 171—183. https://www.researchgate.net/publication/290591153_Physical_mechanical_and_statistical_aspects_of_acoustic_emission_diagnostics
  4. 1 2 3 4 5 Builo, S. I. (2017). Physico-mechanical, statistical and chemical aspects of acoustic emission diagnostics (PDF) (in Russian). Rostov-on-Don: SFU Publishing House. p. 184. ISBN   978-5-9275-2369-6.
  5. ↑ Eaton, M.J.; Pullin, R.; Holford, K.M. (June 2012). "Acoustic emission source location in composite materials using Delta T Mapping". Composites Part A: Applied Science and Manufacturing. 43 (6): 856–863. doi:10.1016/j.compositesa.2012.01.023.
  6. 1 2 McCrory, John P.; Al-Jumaili, Safaa Kh.; Crivelli, Davide; Pearson, Matthew R.; Eaton, Mark J.; Featherston, Carol A.; Guagliano, Mario; Holford, Karen M.; Pullin, Rhys (January 2015). "Damage classification in carbon fibre composites using acoustic emission: A comparison of three techniques". Composites Part B: Engineering. 68: 424–430. doi: 10.1016/j.compositesb.2014.08.046 . hdl: 11311/890355 .
  7. ↑ Popp, Hartmut; Koller, Markus; Jahn, Marcus; Bergmann, Alexander (1 December 2020). "Mechanical methods for state determination of Lithium-Ion secondary batteries: A review". Journal of Energy Storage. 32: 101859. doi: 10.1016/j.est.2020.101859 .
  8. ↑ Benavides, Samuel (2009). Corrosion control in the aerospace industry. Boca Raton, FL: CRC Press. ISBN   978-1-84569-553-8. OCLC   456184838.
  9. 1 2 Blitz, Jack; G. Simpson (1991). Ultrasonic Methods of Non-Destructive Testing. Springer-Verlag New York, LLC. ISBN   978-0-412-60470-6.
  10. ↑ Stuart Hewerdine, ed. (1993). Plant Integrity Assessment by Acoustic Emission Testing (2 ed.). Rugby, UK: Institution of Chemical Engineers. ISBN   978-0-85295-316-7.
  11. ↑ A. A. Anastasopoulos; D. A. Kourousis; P.T. Cole (October 2008). Acoustic Emission Inspection of Spherical Metallic Pressure Vessels. The 2nd International Conference on Technical Inspection and NDT (TINDT2008). Tehran, Iran.
  12. ↑ Estimation of corrosion in reinforced concrete by electrochemical techniques and acoustic emission, journal of advanced concrete technology, vol. 3, No 1, 137–144, February 2005
  13. ↑ Builo S. I., Builo B. I., Kolesnikov V. I., Vereskun V. D., Popov O. N. Application of the Acoustic Emission Method in Problems of Vehicle Diagnostics, Journal of Physics: Conference Series. 2020. vol. 1636. 012006. https://www.researchgate.net/publication/346164546_Application_of_the_acoustic_emission_method_in_problems_of_vehicle_diagnostics
  14. ↑ Huang, Jiaqiang; Boles, Steven T.; Tarascon, Jean-Marie (23 March 2022). "Sensing as the key to battery lifetime and sustainability". Nature Sustainability. 5 (3): 194–204. Bibcode:2022NatSu...5..194H. doi:10.1038/s41893-022-00859-y. S2CID   247623256.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.