Airway (aviation)

Last updated
This instrument flight rules chart shows low-altitude airways in the Oakland Area Control Center (near San Francisco, California). SFO.tif
This instrument flight rules chart shows low-altitude airways in the Oakland Area Control Center (near San Francisco, California).

In the United States, airways [1] or air routes are defined by the Federal Aviation Administration (FAA) in two ways:

Contents

"VOR Federal airways and Low/Medium Frequency (L/MF) (Colored) Federal airways" [2]

These are designated routes which aeroplanes fly to aid in navigation and help with separation to avoid accidents. [3] [4] [5] [lower-alpha 1] Airways are defined with segments within a specific altitude block, corridor width, and between fixed geographic coordinates for satellites navigation system, or between ground-based radio transmitter navigational aids (navaids; such as VORs or NDBs ) or the intersection of specific radials of two navaids.

United States

To guide airmail pilots on their delivery routes, the United States Postal Service constructed the first airways in the United States, the Contract Air Mail routes. These airways were between major cities and identified at night by a series of flashing lights and beacons which pilots flew over in sequence to get from one city to the next. [6] Intermediate fields were located every 30 miles (48 km) in case of emergencies, with at least 2 landing strips a minimum of 2,000 feet (610 m) in length, and 600 feet (180 m) in width. Rotating airways beacons were erected every 10 miles (16 km). [7] However, these visual airways required the pilots to be in visual contact with the ground which precluded flying in fog or clouds. Subsequently, the Department of Commerce funded the development of other means of airway navigation. [8]

The first airways to be delineated by radiofrequency were based on the old Low-frequency radio range also called the "Four Course Radio Range" or "A/N" system. The pilot listened for the stronger of the Morse codes transmitters ("· –" for "A" and "– ·" for "N", indicating left or right of the course); the objective was to be centered on course hearing a steady tone (the A and N Morse codes merge to form a steady tone when the receiver is equidistant from both transmitters).

Later airways were based on low/medium frequency ground stations, like the beat frequency oscillator (BFO) and the non-directional beacon (NDB). These L/M frequency airways were the colored airways. Colored airways still exist, mostly in Alaska. There are only a few colored airways remaining in the contiguous United States. There is one colored airway on the coast of North Carolina called G13 (Green 13). Additionally, there are several colored airways connecting to, and transitioning through, the Florida Keys. B9 (Blue 9) connects the Southern Florida mainland to Marathon Key. B646 (Blue 646) connects Mérida, Mexico to Nassau, Bahamas and transitions through the Florida Keys. A portion of B646 connects Key West to Marathon Key and serves as a bypass for aircraft unable to meet the 15,000 foot minimum altitude along that portion of V3. Finally, G765 (Green 765) connects Key West to Cozumel, Mexico. Colored airways are all depicted in brown on low and high altitude charts produced by the FAA's Aeronautical Navigation Products.

Low altitude airways (below 18,000 feet (5,500 m) MSL) that are based on VOR stations, appear on sectional charts, world aeronautical charts, and en route low altitude charts and are designated with the prefix "V" (pronounced victor, hence, victor airways ). High altitude airways (from 18,000 feet (5,500 m) MSL to FL450) based on VOR stations are called jet routes; they appear on high altitude charts (that usually do not show topography, as the low altitude charts do) and are prefixed by the letter "J". VOR-based routes are depicted in black on low and high altitude charts produced by the FAA's Aeronautical Navigation Products.

With the invention of RNAV routes, airway structure no longer has to be based on ground-based navaids; a new naming convention is used. RNAV routes not based on VOR routes in low altitudes are preceded with the letter "T"; high airway routes are designated with the letter "Q". RNAV routes are depicted in blue on low and high altitude charts produced by the FAA's Aeronautical Navigation Products.

Europe

Airways are corridors 10 nautical miles (19 km) wide of controlled airspace with a defined lower base, usually FL070–FL100, extending to FL195. They link major airports giving protection to IFR flights during the climb and descent phases, and often for non-jet aircraft, cruise phase of flight. Historically, they were laid out between VORs; however, advances in navigational technology mean that this is no longer a necessity. Each airway has a designator containing one letter and one to three numbers. All airspace above FL195 is class C controlled airspace, the equivalent to airways being called Upper Air Routes and having designators prefixed with the letter "U". If an upper air route follows the same track as an airway, its designator is the letter "U" prefix and the designator of the underlying airway.

In the UK, airways are all class A below FL195 and, therefore, VFR flights are prohibited.

Air corridor

An air corridor is a designated region of airspace that an aircraft must remain in during its transit through a given region. Air corridors are typically imposed by military or diplomatic requirements. During the Berlin Blockade, for example, pilots flying across Soviet-controlled German airspace were required to maintain very specific positioning within air corridors defined by the commander in charge of the airlift. Subsequent flights, both military and civilian, between West Germany and West Berlin during the Cold War were required to remain within their designated corridor or risk being shot down.

Air corridors should not be confused with airways. Airways are navigational aids which a pilot generally may deviate from when circumstances warrant, while compliance with a designated air corridor is mandatory.

Notes

  1. The term airway is used by aviation professionals including the International Civil Aviation Organization (ICAO), but other terms have been used or misused by non-specialist sources, sometimes to mean the same thing.

Related Research Articles

<span class="mw-page-title-main">Instrument flight rules</span> Civil aviation regulations for flight on instruments

In aviation, instrument flight rules (IFR) is one of two sets of regulations governing all aspects of civil aviation aircraft operations; the other is visual flight rules (VFR).

A waypoint is an intermediate point or place on a route or line of travel, a stopping point or point at which course is changed, the first use of the term tracing to 1880. In modern terms, it most often refers to coordinates which specify one's position on the globe at the end of each "leg" (stage) of an air flight or sea passage, the generation and checking of which are generally done computationally.

<span class="mw-page-title-main">Non-directional beacon</span> Radio transmitter which emits radio waves in all directions, used as a navigational aid

A non-directional beacon (NDB) or non-directional radio beacon is a radio beacon which does not include inherent directional information. Radio beacons are radio transmitters at a known location, used as an aviation or marine navigational aid. NDB are in contrast to directional radio beacons and other navigational aids, such as low-frequency radio range, VHF omnidirectional range (VOR) and tactical air navigation system (TACAN).

<span class="mw-page-title-main">VHF omnidirectional range</span> Aviation navigation system

Very High Frequency Omnidirectional Range Station (VOR) is a type of short-range radio navigation system for aircraft, enabling aircraft with a receiving unit to determine its position and stay on course by receiving radio signals transmitted by a network of fixed ground radio beacons. It uses frequencies in the very high frequency (VHF) band from 108.00 to 117.95 MHz. Developed in the United States beginning in 1937 and deployed by 1946, VOR became the standard air navigational system in the world, used by both commercial and general aviation, until supplanted by satellite navigation systems such as GPS in the early 21st century. As such, VOR stations are being gradually decommissioned. In 2000 there were about 3,000 VOR stations operating around the world, including 1,033 in the US, but by 2013 the number in the US had been reduced to 967. The United States is decommissioning approximately half of its VOR stations and other legacy navigation aids as part of a move to performance-based navigation, while still retaining a "Minimum Operational Network" of VOR stations as a backup to GPS. In 2015, the UK planned to reduce the number of stations from 44 to 19 by 2020.

Airspace is the portion of the atmosphere controlled by a country above its territory, including its territorial waters or, more generally, any specific three-dimensional portion of the atmosphere. It is not the same as outer space which is the expanse or space outside the Earth and aerospace which is the general term for Earth's atmosphere and the outer space within the planet's vicinity. History:

<span class="mw-page-title-main">Distance measuring equipment</span> Radio navigation technology used in aviation

In aviation, distance measuring equipment (DME) is a radio navigation technology that measures the slant range (distance) between an aircraft and a ground station by timing the propagation delay of radio signals in the frequency band between 960 and 1215 megahertz (MHz). Line-of-visibility between the aircraft and ground station is required. An interrogator (airborne) initiates an exchange by transmitting a pulse pair, on an assigned 'channel', to the transponder ground station. The channel assignment specifies the carrier frequency and the spacing between the pulses. After a known delay, the transponder replies by transmitting a pulse pair on a frequency that is offset from the interrogation frequency by 63 MHz and having specified separation.

In aviation, lowest safe altitude (LSALT) is an altitude that is at least 500 feet above any obstacle or terrain within a defined safety buffer region around a particular route that a pilot might fly. The safety buffer allows for errors in the air by including an additional area that a pilot might stray into by flying off track. By flying at or above this altitude a pilot complies with terrain clearance requirements on that particular flight leg.

<span class="mw-page-title-main">Flight plan</span> Document filed by a pilot or flight dispatcher indicating the aircrafts flight path

Flight plans are documents filed by a pilot or flight dispatcher with the local Air Navigation Service Provider prior to departure which indicate the plane's planned route or flight path. Flight plan format is specified in ICAO Doc 4444. They generally include basic information such as departure and arrival points, estimated time en route, alternate airports in case of bad weather, type of flight, the pilot's information, number of people on board, and information about the aircraft itself. In most countries, flight plans are required for flights under IFR, but may be optional for flying VFR unless crossing international borders. Flight plans are highly recommended, especially when flying over inhospitable areas such as water, as they provide a way of alerting rescuers if the flight is overdue. In the United States and Canada, when an aircraft is crossing the Air Defense Identification Zone (ADIZ), either an IFR or a special type of VFR flight plan called a DVFR flight plan must be filed. For IFR flights, flight plans are used by air traffic control to initiate tracking and routing services. For VFR flights, their only purpose is to provide needed information should search and rescue operations be required, or for use by air traffic control when flying in a "Special Flight Rules Area."

Minimum en route altitude (MEA), alternately spelled as Minimum enroute altitude, is the lowest published altitude between radio navigation fixes that assures acceptable navigational signal coverage and meets obstacle clearance requirements between those fixes.

<span class="mw-page-title-main">Instrument approach</span> Aircraft landing procedure

In aviation, an instrument approach or instrument approach procedure (IAP) is a series of predetermined maneuvers for the orderly transfer of an aircraft operating under instrument flight rules from the beginning of the initial approach to a landing, or to a point from which a landing may be made visually. These approaches are approved in the European Union by EASA and the respective country authorities and in the United States by the FAA or the United States Department of Defense for the military. The ICAO defines an instrument approach as "a series of predetermined maneuvers by reference to flight instruments with specific protection from obstacles from the initial approach fix, or where applicable, from the beginning of a defined arrival route to a point from which a landing can be completed and thereafter, if landing is not completed, to a position at which holding or en route obstacle clearance criteria apply."

<span class="mw-page-title-main">Area control center</span> Air traffic control facility

In air traffic control, an area control center (ACC), also known as a center or en-route center, is a facility responsible for controlling aircraft flying in the airspace of a given flight information region (FIR) at high altitudes between airport approaches and departures. In the US, such a center is referred to as an air route traffic control center (ARTCC).

<span class="mw-page-title-main">Required navigation performance</span> Path selection method for aircraft

Required navigation performance (RNP) is a type of performance-based navigation (PBN) that allows an aircraft to fly a specific path between two 3D-defined points in space.

An aeronautical chart is a map designed to assist in the navigation of aircraft, much as nautical charts do for watercraft, or a roadmap does for drivers. Using these charts and other tools, pilots are able to determine their position, safe altitude, best route to a destination, navigation aids along the way, alternative landing areas in case of an in-flight emergency, and other useful information such as radio frequencies and airspace boundaries. There are charts for all land masses on Earth, and long-distance charts for trans-oceanic travel.

<span class="mw-page-title-main">Approach plate</span> Publication of an aircraft landing procedure

Approach plates are the printed or digital charts of instrument approach procedures that pilots use to fly instrument approaches during instrument flight rules (IFR) operations. Each country maintains its own instrument approach procedures according to International Civil Aviation Organization (ICAO) standards.

Standard instrument departure (SID) routes, also known as departure procedures (DP), are published flight procedures followed by aircraft on an IFR flight plan immediately after takeoff from an airport.

This article describes the graphic conventions used in Sectional charts and Terminal area charts published for aeronautical navigation under Visual Flight Rules in the United States of America. The charts are published "in accordance with Interagency Air Cartographic Committee specifications and agreements, approved by the Department of Defense and the Federal Aviation Administration".

In aviation, an en-route chart is an aeronautical chart that guides pilots flying under instrument flight rules (IFR) during the en-route phase of flight.

<span class="mw-page-title-main">Victor airways</span>

In the United States and Canada, Victor airways are low-altitude airways. They are defined in straight-line segments, each of which is based on a straight line between either two VHF omnidirectional range (VOR) stations, or a VOR and a VOR intersection, hence the beginning letter V.

ICAO performance-based navigation (PBN) specifies that aircraft required navigation performance (RNP) and area navigation (RNAV) systems performance requirements be defined in terms of accuracy, integrity, availability, continuity, and functionality required for the proposed operations in the context of a particular airspace, when supported by the appropriate navigation infrastructure.

Military training routes are aerial corridors across the United States in which military aircraft can operate below 10,000 feet faster than the maximum safe speed of 250 knots that all other aircraft are restricted to while operating below 10,000 feet. The routes are the result of a joint venture between the Federal Aviation Administration and the Department of Defense to provide for high-speed, low-altitude military activities.

References

  1. Wragg, David W. (1973). A Dictionary of Aviation (first ed.). Osprey. p. 31. ISBN   9780850451634.
  2. "Air Traffic Service Routes - Section 3. Federal Airways". Archived from the original on 2020-10-19.
  3. Gunston, Bill (2004). The Cambridge Aerospace Dictionary Cambridge . Cambridge University Press. pp.  34. ISBN   978-0521841405.
  4. FAA regulations 5-3-4. Airways and Route Systems in Section 3. En Route Procedures; archived from www.faa.gov, accessed 25 October 2020
  5. Airway (definition)- Airway Description www.skybrary.aero, accessed 25 October 2020
  6. Pilot's Handbook of Aeronautical Knowledge (PDF). U.S. Department of Transportation: Federal Aviation Administration. 2016. p. 1‑4. Retrieved 2021-04-12.
  7. Smith, Frank (1981). Legacy of Wings; The Harold F. Pitcairn Story. New York: Jason Aronson, Inc. p. 97. ISBN   0876684851.
  8. "The Evolution of Airway Lights and Electronic Navigation Aids". Centennialofflight.net. 1924-07-01. Retrieved 2014-07-28.