Armoured Vehicle Royal Engineers

Last updated

A Churchill AVRE with fascine on a tilt-forward cradle. This particular example is a post-WW2 AVRE on the MK VII chassis Churchill VII AVRE With Fascine.jpg
A Churchill AVRE with fascine on a tilt-forward cradle. This particular example is a post-WW2 AVRE on the MK VII chassis

Armoured Vehicle Royal Engineers (AVRE), also known as Assault Vehicle Royal Engineers, is the title given to a series of armoured military engineering vehicles operated by the Royal Engineers (RE) for the purpose of protecting engineers during frontline battlefield operations.

Contents

In protecting engineers, the vehicles also became a mobile platform for a variety of engineering purposes, mounting large calibre weapons for demolition, carrying engineering stores, mine clearance explosives, a variety of deployable roadways, and modified engineering bridges for gaps that the related Armoured Ramp Carrier ("ARK") vehicles could not overcome.

Development history

Extremely high casualty rates among engineers was one of the primary reasons for the failure of the Dieppe raid of August 1942. Engineers were tasked with getting the tanks off the beach, destroying obstacles and building ramps. In the assault, the engineers were prone to gunfire while setting charges, and became a priority target for the defending forces. Those that did make it to the point where ramps could be built had lost much of their supplies on sunken landing craft. With tanks unable to leave the beaches, the raid stalled and failed.

Following failure of the raid, a Royal Canadian Engineer officer, Lt J.J. Denovan who was attached to the Department of Tank Design, proposed a vehicle to protect engineers during assault operations. Development commenced based on the experiences at Dieppe. Experiments used Churchill, Sherman and Ram tanks. The side door became a critical component for the new vehicle, allowing engineers to exit the vehicle under protection, and retreat back inside while blasting. In October 1942 a prototype based on the Churchill tank was ordered. The Churchill proved ideal, having a large amount of space inside for demolition stores, and side exit doors. The interior munition storage was removed, as was the turret basket and co-drivers seat, replaced with stowage. This provided space for 36 cu. ft. of demolition supplies and tools.

AVRE 230 mm petard mortar and its ammunition The 29cm Petard spigot mortar on a Churchill AVRE of 79th Squadron, 5th Assault Regiment, Royal Engineers, under command of 3rd Infantry Division, 29 April 1944. A 40lb bomb can be seen on the right. H38001.jpg
AVRE 230 mm petard mortar and its ammunition

The turret, initially not required, was retained allowing a spigot mortar firing a petard to be added. The petard mortar was a separate development, firing a large demolition charge, the "Bomb, Demolition Number I", that became known as the "flying dustbin". Development on this began in September 1942 and was united with the Churchill turret following experimental use on a Covenanter tank. With plenty of space inside the Churchill, a number of "flying dustbins" could be carried in addition to the demolitions stores. The petard was reloaded through a sliding cover that replaced one of the forward drivers hatches in the top of the hull.

Together the vehicle was named Assault Vehicle Royal Engineers. Trials of the new vehicle were undertaken throughout 1943. The vehicle was not known as "Armoured Vehicle Royal Engineers" at this time.

Production commenced in 1944 based on a mixed fleet of Churchill III and IV vehicles. These were assigned to three regiments of the Royal Engineers forming the new 1st Assault Brigade Royal Engineers, part of the 79th Armoured Division. The vehicles became the basis for a range of modifications and additions as part of Hobart's Funnies.

Nomenclature

AVRE vehicles have been known by several different names through their lifespan.

Secrecy over the meaning of the codenames given to Hobart's Funnies in the lead-in to D-Day led many to refer to the AVRE simply as an "engineer tank", most not knowing the AVRE name or what AVRE stood for. [1] This led to confusion with other types of engineer tank, such as recovery vehicles. In October 1943 an army training memorandum was issued removing the ambiguity in naming and defining the "Assault Vehicle Royal Engineers" name for all users.

The majority of documentation continued to refer to the abbreviated "AVRE" (or "A.Vs.R.E." in plural). Even the Churchill AVRE's own instruction book did not explain what A.V.R.E. stood for. With infrequent use of the full form, naming became confused.

At the end of the war, the Final Report of the 79th Armoured Division, the records of the Department of Tank Design, and the official history of the 1st Assault Brigade Royal Engineers, all use the "Assault Vehicle" terminology. The official history of the 79th Armoured Division states "Armoured Vehicle Royal Engineers" however, although notes that it was rushed into print. As the latter was provided to all members of the division, the "Armoured Vehicle" terminology gained significant traction.

The vehicles continue to be referred to primarily in the abbreviated "AVRE" form. When rarely defined, both the Churchill VII AVRE and the Centurion AVRE became known by both Assault and Armoured terms interchangeably, with the latter Armoured term becoming more common. Nomenclature settled on Armoured Vehicle with the introduction of the Chieftain Armoured Vehicle Royal Engineers. "Armoured Vehicle Royal Engineers" has since become the accepted term, retrospectively applied to previous vehicles in most references.

More recently, the AVRE designation appears to have been dropped from Trojan.

Models

Churchill IV AVRE in France, 1944 D-day - British Forces during the Invasion of Normandy 6 June 1944 B5040.jpg
Churchill IV AVRE in France, 1944
Churchill VII AVRE with fascine Churchill VII AVRE With Fascine.jpg
Churchill VII AVRE with fascine
Centurion AVRE Centurion-AVRE-165-Fosgene.jpg
Centurion AVRE

Churchill III and IV AVRE

Churchill AVRE was a Churchill III or IV armed with a 230 mm petard spigot mortar, officially designated; Mortar, Recoiling, Spigot, 29mm [Nb 1] , Mk I or II. [2] The mount replaced the 6-pounder gun in welded turrets on the Mark III and cast turrets on the Mark IV, otherwise the vehicles are identical. The 6-pounder gun mounting was modified, and retained the 6-pounder sights although "flying dustbin" effective range was only around 80 yards of 230 maximum.

Crew was increased to six to accommodate a demolition NCO in addition to driver, commander, gunner, wireless operator, and co-driver/machine gunner.[ citation needed ]

Internal ammunition stowage and the co-driver / hull gunner's seat was removed to provide compartments for demolition charges. This housed stores of the "General Wade" 26 lb explosive charge, and "Beehive" charges of up to 75 lbs of explosive. Both types of charge had to be set manually, but could be detonated from the relative safety of the AVRE interior. In the remaining space, compartments in the sponsons were created fore and aft of the side hatches for "flying dustbin" ammunition.

Churchill VII AVRE

Post-war, new Churchill AVREs were created using the Churchill VII base vehicle re-armed with a short barrelled L9A1 165 mm demolition gun. This fired a 64 lb (29 kg) HESH round. [3]

Centurion Mk 5 AVRE "AVRE 165"

FV4003 Centurion Mk 5 AVRE. Armed with a short barrelled L9A1 165 mm demolition gun, it entered service in 1963, replacing the Churchill AVRE. [3] The vehicle was later renamed AVRE 165 relating to its primary armament. [4] The armament was capable of firing a 60 lb (29 kg) high-explosive squash head (HESH) round.

The vehicle front added a dozer blade to the front, and frequently towed the Giant Viper for mine clearance or other trailers for stores. Large turret bins provided stowage. [4] The dozer attachment was also provided on regular tanks as the FV4019 Centurion Mk 5 Bulldozer. [5]

Centurion AVREs remained in use, and were up-armoured for Operation Desert Storm in 1991. [4]

Centurion Mk 12 AVRE "AVRE 105"

FV4203 Centurion Mk 12 AVRE. A modified Artillery Observation Post vehicle, it was armed with the conventional 105 mm Royal Ordnance L7 rifled gun and provided with track width mine clearance ploughs instead of the dozer blade on the Mk 5. [4]

Chieftain AEV and FV4203 Chieftain AVRE

Replacement of Centurion AVRE was planned to be accomplished by two new vehicles splitting the AVRE role: the Chieftain Armoured Engineering Vehicle (Gun) and Chieftain Armoured Engineering Vehicle (Winch). Both were to be multi-role vehicles capable of more than just the AVRE function.

FV4203 AVRE vehicles were almost identical to the Chieftain ARV, also based on the AEV (Winch), but added a dozer blade/bucket, deployable bridge, and the ability to launch a roadway. [7] The project was cancelled in favour of completing normal engineering operations with the lightly armoured Combat Engineer Tractor (CET) while retaining the Centurion AVRE in frontline service. [6]

The FV4203 AVRE prototypes were later converted for Armoured Repair and Recovery Vehicle (ARRV) trials.

Chieftain "CHAVRE" AVRE

Chieftain "CHAVRE" AVRE X 21 A in ERV.JPG
Chieftain "CHAVRE" AVRE

With the introduction of Challenger 1, the Centurion AVRE was struggling to keep up, while military requirements needed a larger number of trackways to be carried. [6] Surplus Chieftain vehicles could have the turret removed to reduce the vehicle weight, providing enhanced mobility even when loaded with engineering stores. Removal of the turret would also allow six Class 60 trackways or three fascines to be carried on top of the vehicle. [6]

The Chieftain tank based "Willich Chieftain AVRE" entered service in 1987. This vehicle was designed by Capt D Clegg MBE RE. Twelve vehicles were built by 32 Armoured Engineer Regiment and 21 Engineer Base Workshop of the Royal Engineers under the direction of Lt Col JF Johnson RE based in the German town of Willich, hence its name. [8] [9] Some of these vehicles saw use in the First Gulf War. [10]

In 1989 a programme was launched to convert a further 48 vehicles with prototypes arriving in 1991. The Chieftain "CHAVRE" AVRE entered service in 1994. 48 units were produced by Vickers Defence Systems. [9] The "CHAVRE" nomenclature mirrored that of the Chieftain ARRV "CHARRV" as distinguished from the Challenger ARRV "CRARRV". [6]

Each CHAVRE provided a 10 tonne winch and Atlas crane for engineering operations, along with a trackway on top for multiple fascines or stores. It also fitted a dozer blade or mine plough. [10]

With no primary armament, CHAVRE was initially used alongside the Centurion AVRE. [10]

Trojan

TROJAN Trojan AVRE - Tankfest 2009.jpg
TROJAN

AVRE functions have been combined with others into the Trojan Combat Engineer Vehicle (CEV) based on the Challenger 2 chassis.

Trojan will be equipped with an articulated excavator arm, a dozer blade and rails for fascines.

33 units have been ordered from BAE Systems Land Systems.

Operational history

AVRE on the Normandy beach during the D-Day landings D-day - British Forces during the Invasion of Normandy 6 June 1944 B5095.jpg
AVRE on the Normandy beach during the D-Day landings

Churchill III and IV AVRE vehicles were successfully used to breach defences in the D-Day landings, and continued in use through the rest of the allied advance to Nazi Germany.

The Petard Mortar's ability to demolish obstructions and fortifications proved valuable to the allied advance, while the morale impact of seeing the large gun caused many enemies to abandon their positions. AVRE vehicles were frequently teamed with Churchill Crocodile flamethrowers for bunker clearance. The AVRE would crack the defences, allowing the flamethrower to soak the interior with flammable liquid, forcing those inside to surrender.

Centurion AVRE and Chieftain CHAVRE vehicles were both successfully used in Operation Granby in the early 1990s.

Extended use of the Centurion AVRE made the Centurion tank, developed during the latter half of the second world war, the longest serving military vehicle in the British Army.

Attachments and accessories

Demolitions

Churchill "Double Onion" tank, could place demolition charges at heights up to 12 feet ChurchillDoubleOnion.jpeg
Churchill "Double Onion" tank, could place demolition charges at heights up to 12 feet
Light Carrot tank, like the Double Onion used to demolish walls LightCarrot tank ww2.jpg
Light Carrot tank, like the Double Onion used to demolish walls

The Carrot provided explosive charges on metal prongs extended from the front of the vehicle. These could be pushed up to an obstacle, released, and fired from within the vehicle, protecting engineers from the need to exit the safety of the armoured vehicle interior.

Onion built upon the Carrot concept providing a much larger frame of explosives to blow a larger gap in concrete obstacles.

Goat provided a similar frame of explosives to Onion and Carrot, but carried horizontally to allow a much greater charge to be carried. This was released by prongs extending from the front, allowing it to pivot into a vertical position before detaching from the vehicle.

Mine clearance

A preserved, World War II, Sherman Crab - an M4 Sherman tank fitted with a flail M4a4 flail cfb borden 1.JPG
A preserved, World War II, Sherman Crab – an M4 Sherman tank fitted with a flail

During World War II the Sherman Crab was the primary (and most effective) mine clearance vehicle for the 79th Armoured Division, but AVREs carried a range of mine clearance devices to supplement them.

A Lane marker attachment could be fitted to the sides of the AVRE to delineate lanes through minefields or cleared terrain. Similar to the Sherman Crab, it deployed both tape and lights.

Snake was a mine-clearing line charge consisted of sections of 3-inch pipe filled with explosive to extend and then detonate across a minefield. The concept is similar to the bangalore torpedo but Snake is much larger – Snake pipes run the length of the AVRE vehicle with multiple pipes carried on the trackguards of modified AVREs. Once assembled together into longer lengths, Snake could be towed by the AVRE into position, and then pushed across a minefield. A shaped end was created for the Snake to prevent it digging into the ground when pushed. Detonation destroyed the mines along the length of the pipe, forming a large path across the minefield.

Conger was a similar device to Snake, providing a rocket propelled flexible tube that was carried in, and launched from, a converted engineless Universal Carrier towed behind the AVRE. Once in position, the hose was propelled by an attached rocket across the minefield. The tube was pump-filled with a special nitroglycerine based explosive known as 822C. The device was used operationally during the D-Day invasions, but operations were stopped after an explosion near the village of IJzendijke  [ nl ]. In preparations for use for an upcoming attack, more than a ton of 822C detonated while being unloaded from two lorries. The explosion caused numerous casualties and destroyed four nearby AVREs, while the lorries "disappeared". [11] [12] [13] [ page needed ]

Giant Viper is a post-war re-working of the Conger concept using a trailer and pre-filled, safer, hose and explosive. It was used with Centurion and Chieftain AVREs (and other vehicles) and saw use in the Iraq conflict with them. It has been replaced with the Python Minefield Breaching System. [14]

Anti-mine Plough was used to avoid cratering an approach and rendering it impassible to following vehicles. A number of types have been used. These push the mines to the sides of the vehicle where they can be dealt with later by sappers on foot.

Alternatively, mine rollers like the Canadian Indestructible Roller Device (CIRD) could detonate mines ahead of the vehicle by applying a vehicle-like ground weight. These pivoted up on their mountings upon explosion before dropping back down to continue.

Tracks and roadways

Churchill AVRE with Bobbin AVRE-Bobbin.jpg
Churchill AVRE with Bobbin

Roly-Poly and Bobbin both provided a track laying roll in front of the AVRE over which the AVRE drove (known as "carpet laying"). This provided a roadway over soft ground which the tanks would otherwise sink into. Roly-Poly used steel roller shuttering while Bobbin used reinforced fabric matting. [15] Both were used on D-Day.

Log Carpet provided an alternative formed of chain-linked logs. This was folded flat on raised supports over the AVRE with an explosive charge to release the front. The log carpet would then drop down in front of the tank log-by-log, with the weight dragging further logs from the top. Logs were robust, each,14 ft long by 27 in. diameter linked with 2 in. wire rope. This proved a challenge to load, and Log Carpet AVREs had to be driven into a pit to enable the logs to be loaded at ground-level. [16]

Log Carpet could also be fitted to the unit's LVT4 Buffalo amphibious vehicles, and was particularly effective on waterlogged ground. [16]

Class 30 and Class 60 Trackways were later developments in the 1960s following extensive cold-war exercises in Germany, similar to Roly-Poly.

Bridging and gap clearance

AVRE carrying a fascine over a similar fascine AVRE 01.jpg
AVRE carrying a fascine over a similar fascine

During World War II, the AVRE was provided with a platform allowing a fascine to be carried on the vehicle front while the turret was traversed through 90 degrees. This could be released from within the vehicle to drop into gaps and ditches, allowing tanks (commencing with the AVRE itself) to cross, or angle up and over a ridge.

AVRE's could also be modified with mounts and supports to carry a ready-assembled Small Box Girder Bridge from the front glacis plate. This could be dropped over gaps similar to traditional engineer bridging, or used to provide a ramp over a wall. Later, a towed version of the Small Box Girder Bridge was also developed, and was able to traverse a Bailey bridge for gaps further along the assault.

A 60 ft section of Bailey bridge could also be pushed as the "Skid Bailey", with the leading sections raised slightly by winch to overcome obstacles. This allowed larger gaps to be breached. Trials and training were also conducted with the Bailey Mobile Bridge, providing 150 ft of bridge articulated on tracks at the centre, and the Brown Bailey, carrying 140 ft of Bailey bridge between two tanks, the rear AVRE launching the bridge over rollers on the front vehicle.

Post-war a Folding Small Box Girder Bridge was also developed, articulating in the middle.

AVRE bridging can be distinguished from the Armoured Ramp Carrier (ARK) by both purpose and operator. AVRE bridges leverage the AVRE to enable Royal Engineers to more safely accomplish traditional bridging activities where an ARK may not be appropriate. The ARK is intended to rapidly deploy a ramp or smaller gap bridge without the need for specialised engineering skillset, simply by driving into it. An AVRE deployed fascine could be used to raise the front of the ARK if needed, such as ahead of large sea walls. Latterly ARK vehicles were used by the Royal Armoured Corps to undertake the task [17]

Armoured vehicle-launched bridge (AVLB) bridge-layer vehicles have replaced AVRE bridging in more recent years, although fascines are still carried for smaller obstacles.

AVRE trailers

An Armoured Sled was provided for AVRE with droppable sides, allowing further engineering supplies to be dragged by the vehicle. Engineers also used Gutted Carrier based on the universal carrier or its predecessor vehicles, for the same purpose. These were stripped of engine and internals, and dragged using the same linkage used for Conger.

Post war, a dedicated AVRE trailer, designated "Trailer, Cargo, 7 1/2 ton, 4 wheeled, Centurion A.V.R.E." provided a cross country load carrying capability behind the AVRE.

Related vehicles provided dedicated bridging and mine clearance, becoming the Armoured Ramp Carrier (ARK), Armoured vehicle-launched bridge (AVLB) and Mine flail (Lobster, Crab) vehicles.

2 Churchill ARKs bridging a difficult obstacle Churchill Ark 03.jpg
2 Churchill ARKs bridging a difficult obstacle

List of vehicles deployed

Valentine Bridgelayer A Valentine bridgelayer of the 3rd Independent Bridge Building Company, Royal Armoured Corps, spans a damaged bridge near Meiktila, 28 March 1945.jpg
Valentine Bridgelayer
Mark I tank Heavy RE tank variants
Light Tank Mk V
Covenanter tank
Valentine tank
FV180 Combat Engineer Tractor (CET)
Shielder Vehicle Launched Scatterable Mine System
Challenger variants
Terrier CET

See also

Notes

Comments

  1. Mistaking "29 mm", that refers to the diameter of the spigot itself, as 29 cm for the calibre of the weapon itself might be the reason for the faulty claim of the petard was 290 mm. The measurements are 29 mm spigot, 230 mm between the lands and 240 mm from groove to groove, with 20 mm thickness of the goods.

Related Research Articles

<span class="mw-page-title-main">Armoured fighting vehicle</span> Combat vehicle with both armament and armour

An armoured fighting vehicle or armored fighting vehicle (AFV) is an armed combat vehicle protected by armour, generally combining operational mobility with offensive and defensive capabilities. AFVs can be wheeled or tracked. Examples of AFVs are tanks, armoured cars, assault guns, self-propelled artilleries, infantry fighting vehicles (IFV), and armoured personnel carriers (APC).

<span class="mw-page-title-main">Military engineering vehicle</span> Battlefield support vehicle

A military engineering vehicle is a vehicle built for construction work or for the transportation of combat engineers on the battlefield. These vehicles may be modified civilian equipment or purpose-built military vehicles. The first appearance of such vehicles coincided with the appearance of the first tanks, these vehicles were modified Mark V tanks for bridging and mine clearance. Modern military engineering vehicles are expected to fulfill numerous roles, as such they undertake numerous forms, examples of roles include; bulldozers, cranes, graders, excavators, dump trucks, breaching vehicles, bridging vehicles, military ferries, amphibious crossing vehicles, and combat engineer section carriers.

<span class="mw-page-title-main">Churchill tank</span> British heavy infantry tank

The Tank, Infantry, Mk IV (A22) Churchill was a British infantry tank used in the Second World War, best known for its heavy armour, large longitudinal chassis with all-around tracks with multiple bogies, its ability to climb steep slopes, and its use as the basis of many specialist vehicles. It was one of the heaviest Allied tanks of the war.

<span class="mw-page-title-main">Centurion (tank)</span> British main battle tank

The Centurion was the primary British Army main battle tank of the post-World War II period. Introduced in 1945, it is widely considered to be one of the most successful post-war tank designs, remaining in production into the 1960s, and seeing combat into the 1980s. The chassis was adapted for several other roles, and these variants have remained in service. It was a very popular tank with good armour, mobility, and a powerful main armament.

<span class="mw-page-title-main">Cromwell tank</span> British WWII cruiser tank

The Cromwell tank, officially Tank, Cruiser, Mk VIII, Cromwell (A27M), was one of the series of cruiser tanks fielded by Britain in the Second World War. Named after the English Civil War-era military leader Oliver Cromwell, the Cromwell was the first tank put into service by the British to combine high speed from a powerful, reliable engine and reasonable armour. The intended dual-purpose high velocity gun could not be fitted in the turret, so a medium velocity dual purpose gun was fitted instead. Further development of the Cromwell combined with a high velocity gun led to the Comet tank.

<span class="mw-page-title-main">M728 Combat Engineer Vehicle</span> Military engineering vehicle

The M728 Combat Engineer Vehicle (CEV) is a full-tracked vehicle used for breaching, obstacle removal, and pioneering operations. Production commenced in 1965 and ceased in 1987. A total of 312 of all variants of these armored engineer vehicles were produced.

<span class="mw-page-title-main">Chieftain (tank)</span> Main battle tank

The FV4201 Chieftain was the main battle tank (MBT) of the United Kingdom from the 1960s into 1990s. When introduced, it was among the most heavily armed MBTs of the era, mounting a 120 mm Royal Ordnance L11 gun, the equal of the much larger specialist heavy tanks then in service. It also was among the most heavily armoured, with up to 195 mm (7.7 in) that was highly sloped to offer 388 mm (15.3 in) thickness along the line of sight.

<span class="mw-page-title-main">Hobart's Funnies</span> Modified tanks first used in the Normandy Landings

Hobart's Funnies is the nickname given to a number of specialist armoured fighting vehicles derived from tanks operated during the Second World War by units of the 79th Armoured Division of the British Army or by specialists from the Royal Engineers.

<span class="mw-page-title-main">79th Armoured Division (United Kingdom)</span> Military unit

The 79th Armoured Division was a specialist armoured division of the British Army created during the Second World War. The division was created as part of the preparations for the Normandy invasion on 6 June 1944, D-Day.

<span class="mw-page-title-main">Fascine</span> Bundle of wood used for support or path construction

A fascine is a rough bundle of brushwood or other material used for strengthening an earthen structure, or making a path across uneven or wet terrain. Typical uses are protecting the banks of streams from erosion, covering marshland, or providing ground improvement in a manner similar to that of modern geotextiles.

<span class="mw-page-title-main">Armored bulldozer</span> Bulldozer modified for use in combat engineering

The armored bulldozer is a basic tool of combat engineering. These combat engineering vehicles combine the earth moving capabilities of the bulldozer with armor which protects the vehicle and its operator in or near combat. Most are civilian bulldozers modified by addition of vehicle armor/military equipment, but some are tanks stripped of armament and fitted with a dozer blade. Some tanks have bulldozer blades while retaining their armament, but this does not make them armored bulldozers as such, because combat remains the primary role — earth moving is a secondary task.

<span class="mw-page-title-main">Armoured vehicle-launched bridge</span> Military engineering vehicle

An armoured vehicle-launched bridge (AVLB) is a combat support vehicle, sometimes regarded as a subtype of military engineering vehicle, designed to assist militaries in rapidly deploying tanks and other armoured fighting vehicles across gap-type obstacles, such as rivers. The AVLB is usually a tracked vehicle converted from a tank chassis to carry a folding metal bridge instead of weapons. The AVLB's job is to allow armoured or infantry units to cross craters, anti-tank ditches, blown bridges, railroad cuts, canals, rivers and ravines, when a river too deep for vehicles to wade through is reached, and no bridge is conveniently located, or sufficiently sturdy, a substantial concern when moving 60-ton tanks.

The 1st Assault Brigade Royal Engineers was a specialised armoured formation of the British Army active in the Second World War. It was formed in mid-1943 and its structure was three assault regiments of the Royal Engineers. It was assigned to the 79th Armoured Division in preparation for the Normandy invasion of 6 June 1944. The unit comprised armoured vehicles modified for specialist roles, intended to assist with the landing phase of the operation.

<span class="mw-page-title-main">T-26 variants</span> Vehicles based on the Soviet T-26 light tank

More than 50 different modifications and experimental vehicles based on the T-26 light infantry tank chassis were developed in the USSR in the 1930s, with 23 modifications going into series production. The majority were armoured combat vehicles: flame tanks, artillery tractors, radio-controlled tanks (teletanks), military engineering vehicles, self-propelled guns and armoured personnel carriers. They were developed at the Leningrad Factory of Experimental Mechanical Engineering by talented Soviet engineers P.N. Syachentov, S.A. Ginzburg, L.S. Troyanov, N.V. Tseits, B.A. Andryhevich, M.P. Zigel and others. Many Soviet tank engineers were declared "enemies of the nation" and repressed during Stalin's Great Purge from the middle of the 1930s. As a result, work on self-propelled guns and armoured carriers ceased in the USSR during that time. T-26 light tanks were also modified into armoured combat vehicles in the field during wartime.

<span class="mw-page-title-main">Trojan Armoured Vehicle Royal Engineers</span> Combat engineering vehicle

The Trojan Armoured Engineer Vehicle (AEV) is a combat engineering vehicle of the British Army. It is used to breach minefields and for many other tasks. It is currently in use with the Royal Engineers.

<span class="mw-page-title-main">Tanks of New Zealand</span> Use of tanks by the New Zealand Army

The New Zealand Army use of tanks from after the First World War, through the interwar period, the Second World War, the Cold War and to the present day has been limited, but there is some history. The New Zealand armed forces developed in the early twentieth century but served alongside the British and other Empire and Commonwealth nations in World War I and World War II.

<span class="mw-page-title-main">East Lancashire Royal Engineers</span> Military unit

The East Lancashire Royal Engineers was a Volunteer unit of Britain's Royal Engineers raised in Manchester in 1901. It became the engineer component of the 42nd Division of the Territorial Force, seeing service in Egypt, at Gallipoli and on the Western Front during the First World War. In the Second World War, it took part in the Dunkirk evacuation with 42nd Division, and then converted to the armoured assault engineer role in 79th Armoured Division in North West Europe. Its duplicate unit served in Tunisia and Italy. The unit continues today as part of 75 Engineer Regiment in the Army Reserve.

<span class="mw-page-title-main">AEV 3 Kodiak</span> Armoured engineering variant of a main battle tank

The AEV 3 Kodiak is a Leopard 2 main battle tank (MBT) based armoured engineering vehicle that can be used for a wide variety of battlefield engineering, infrastructure and support roles. These roles can include, but would not be limited to, minefield breaching, route denial, dozing and digging tasks, and the erection or demolition of obstacles. The vehicle was originally developed for a Swiss Army requirement by the consortium of Rheinmetall Landsysteme GmbH (Germany) and RUAG Defence (Switzerland).

References

  1. Flamethrower; Andrew Wilson; 1956
  2. Armoured Archives. "AVRE 230mm - Fact Checking" . YouTube . Archived from the original on 7 July 2022.[ user-generated source ]
  3. 1 2 "Assault bridging and equipment". www.remuseum.org.uk. Archived from the original on 27 May 2008.
  4. 1 2 3 4 Janes AFV recognition handbook, page 467
  5. "FV4007 Centurion - Tanks Encyclopedia". www.tanks-encyclopedia.com. 14 November 2014. Retrieved 4 January 2017.
  6. 1 2 3 4 5 Chieftain Main Battle Tank 1965-2003; Simon Dunstan; Page 24, 33, 41-43
  7. reme journal
  8. "UK Government Web Archive". webarchive.nationalarchives.gov.uk. Retrieved 13 October 2023.
  9. 1 2 "The Tank Museum on Facebook". Facebook . Archived from the original on 27 April 2022.[ user-generated source ]
  10. 1 2 3 Jane's afv recognition handbook, second edition, Christopher Foss, page 466
  11. K. Margry, "It happened here: The explosion at IJzendijke, Tijdschrift '40 -'45 Then and now", no. 99, Uitgeverij Quo Vadis, Soest, 1999, p. 44-54.
  12. "Churchill AVRE". Tanks Encyclopedia. 10 July 2018.
  13. Fletcher, David (1984). Vanguard of Victory the 79th Armoured Division. ISBN   9780112904229. ISBN   011290422X
  14. "Engineering Equipment". www.army.mod.uk. Retrieved 13 January 2017.
  15. A.R.E. The Story of the 1st Assault Brigade Royal Engineers 1943-45, page 15
  16. 1 2 The Funnies, George W. Futter, page 41
  17. 79th Armoured Division Final Report, Section 20 and 21 (page unnumbered)
  18. 1 2 "BAE brochure on Armoured Engineer Vehicles" (PDF). Jdw.janes.com. Retrieved 24 November 2014.[ permanent dead link ]
  19. "Hansard". Publications.parliament.uk. Retrieved 24 November 2014.
  20. "Shielder specifications - basic language". Atk.com. Retrieved 24 November 2014.
  21. "データ復旧や比較に関してのこと | データ復旧の比較-業者と個人-". defence-data.com. Archived from the original on 28 September 2007.

References