Bending (metalworking)

Last updated
Bending Bending, Constructionwork.jpg
Bending
A chimney starter, a sample product of bending Chimney starter.JPG
A chimney starter, a sample product of bending

Bending is a manufacturing process that produces a V-shape, U-shape, or channel shape along a straight axis in ductile materials, most commonly sheet metal. [1] Commonly used equipment include box and pan brakes, brake presses, and other specialized machine presses. Typical products that are made like this are boxes such as electrical enclosures and rectangular ductwork.

Contents

Process

Bending process Bystronic Bending.jpg
Bending process

In press brake forming, a work piece is positioned over the die block and the die block presses the sheet to form a shape. [1] Usually bending has to overcome both tensile stresses and compressive stresses. When bending is done, the residual stresses cause the material to spring back towards its original position, so the sheet must be over-bent to achieve the proper bend angle. The amount of spring back is dependent on the material, and the type of forming. When sheet metal is bent, it stretches in length. The bend deduction is the amount the sheet metal will stretch when bent as measured from the outside edges of the bend. The bend radius refers to the inside radius. The formed bend radius is dependent upon the dies used, the material properties, and the material thickness.

The U-punch forms a U-shape with a single punch. [1]

Types

A schematic of coining with a backgauge Press brake schematic.svg
A schematic of coining with a backgauge

There are three basic types of bending on a press brake, each is defined by the relationship of the end tool position to the thickness of the material. These three are Air Bending, Bottoming and Coining. The configuration of the tools for these three types of bending are nearly identical. A die with a long rail form tool with a radiused tip that locates the inside profile of the bend is called a punch. Punches are usually attached to the ram of the machine by clamps and move to produce the bending force. A die with a long rail form tool that has concave or V-shaped lengthwise channel that locate the outside profile of the form is called a die. Dies are usually stationary and located under the material on the bed of the machine. Note that some locations do not differentiate between the two different kinds of dies (punches and dies). The other types of bending listed use specially designed tools or machines to perform the work.

Air bending

This bending method forms material by pressing a punch (also called the upper or top die) into the material, forcing it into a bottom V-die, which is mounted on the press. The punch forms the bend so that the distance between the punch and the side wall of the V is greater than the material thickness (T).

Either a V-shaped or square opening may be used in the bottom die (dies are frequently referred to as tools or tooling). Because it requires less bend force, air bending tends to use smaller tools than other methods.

Some of the newer bottom tools are adjustable, so, by using a single set of top and bottom tools and varying press-stroke depth, different profiles and products can be produced. Different materials and thicknesses can be bent in varying bend angles, adding the advantage of flexibility to air bending. There are also fewer tool changes, thus, higher productivity. [2]

A disadvantage of air bending is that, because the sheet does not stay in full contact with the dies, it is not as precise as some other methods, and stroke depth must be kept very accurate. Variations in the thickness of the material and wear on the tools can result in defects in parts produced. [2] Thus, the use of adequate process models is important. [3]

Air bending's angle accuracy is approximately ±0.5 deg. Angle accuracy is ensured by applying a value to the width of the V opening, ranging from 6 T (six times material thickness) for sheets to 3 mm thick to 12 T for sheets more than 10 mm thick. Springback depends on material properties, influencing the resulting bend angle. [2]

Depending on material properties, the sheet may be overbent to compensate for springback. [4]

Air bending does not require the bottom tool to have the same radius as the punch. Bend radius is determined by material elasticity rather than tool shape. [2]

The flexibility and relatively low tonnage required by air bending are helping to make it a popular choice. Quality problems associated with this method are countered by angle-measuring systems, clamps and crowning systems adjustable along the x and y axes, and wear-resistant tools. [2]

The K-factor approximations given below are more likely to be accurate for air bending than the other types of bending due to the lower forces involved in the forming process.

Bottoming

In bottoming, the sheet is forced against the V opening in the bottom tool. U-shaped openings cannot be used. Space is left between the sheet and the bottom of the V opening. The optimum width of the V opening is 6 T (T stands for material thickness) for sheets about 3 mm thick, up to about 12 T for 12 mm thick sheets. The bending radius must be at least 0.8 T to 2 T for sheet steel. Larger bend radii require about the same force for bottoming as they do for air bending, however, smaller radii require greater force—up to five times as much—than air bending. Advantages of bottoming include greater accuracy and less springback. A disadvantage is that a different tool set is needed for each bend angle, sheet thickness, and material. In general, air bending is the preferred technique. [2]

Coining

In coining, the top tool forces the material into the bottom die with 5 to 30 times the force of air bending, causing permanent deformation through the sheet. There is little, if any, spring back. Coining can produce an inside radius as low as 0.4 T, with a 5 T width of the V opening. While coining can attain high precision, higher costs mean that it is not often used.

Three-point bending

Three-point bending is a newer process that uses a die with an adjustable-height bottom tool, moved by a servo motor. The height can be set within 0.01 mm. Adjustments between the ram and the upper tool are made using a hydraulic cushion, which accommodates deviations in sheet thickness. Three-point bending can achieve bend angles with 0.25 deg. precision. While three-point bending permits high flexibility and precision, it also entails high costs and there are fewer tools readily available. It is being used mostly in high-value niche markets. [2]

Folding

In folding, clamping beams hold the longer side of the sheet. The beam rises and folds the sheet around a bend profile. The bend beam can move the sheet up or down, permitting the fabricating of parts with positive and negative bend angles. The resulting bend angle is influenced by the folding angle of the beam, tool geometry, and material properties. Large sheets can be handled in this process, making the operation easily automated. There is little risk of surface damage to the sheet. [2]

Wiping

In wiping, the longest end of the sheet is clamped, then the tool moves up and down, bending the sheet around the bend profile. Though faster than folding, wiping has a higher risk of producing scratches or otherwise damaging the sheet, because the tool is moving over the sheet surface. The risk increases if sharp angles are being produced. [2]

This method will typically bottom or coin the material to set the edge to help overcome springback. In this bending method, the radius of the bottom die determines the final bending radius.

Rotary bending

Rotary bending is similar to wiping but the top die is made of a freely rotating cylinder with the final formed shape cut into it and a matching bottom die. On contact with the sheet, the roll contacts on two points and it rotates as the forming process bends the sheet. This bending method is typically considered a "non-marking" forming process suitable to pre-painted or easily marred surfaces. This bending process can produce angles greater than 90° in a single hit on standard press brakes process.

Roll bending

Roll bending Rundwalzen.png
Roll bending

The roll bending process induces a curve into bar or plate workpieces. There should be proper pre-punching allowance.

Elastomer bending

In this method, the bottom V-die is replaced by a flat pad of urethane or rubber. As the punch forms the part, the urethane deflects and allows the material to form around the punch. This bending method has a number of advantages. The urethane will wrap the material around the punch and the end bend radius will be very close to the actual radius on the punch. It provides a non-marring bend and is suitable for pre-painted or sensitive materials. Using a special punch called a radius ruler with relieved areas on the urethane U-bends greater than 180° can be achieved in one hit, something that is not possible with conventional press tooling. Urethane tooling should be considered a consumable item and while they are not cheap, they are a fraction of the cost of dedicated steel. It also has some drawbacks, this method requires tonnage similar to bottoming and coining and does not do well on flanges that are irregular in shape, that is where the edge of the bent flange is not parallel to the bend and is short enough to engage the urethane pad.

Joggling

A joggle bend in sheet metal (at top of image) and a hand joggling tool Absetzzange-blech.jpg
A joggle bend in sheet metal (at top of image) and a hand joggling tool

Joggling, [5] also known as joggle bending, is an offset bending process in which two opposite bends with equal angles are formed in a single action creating a small s-shape bend profile and an offset between the unbent face and the result flange that is typically less than 5 material thicknesses. [6] Often the offset will be one material thickness, in order to allow a lap joint where the edge of one sheet of material is laid on top of the other.

Calculations

Many variations of these formulas exist and are readily available online. These variations may often seem to be at odds with one another, but they are invariably the same formulas simplified or combined. What is presented here are the unsimplified formulas. All formulas use the following keys:

The neutral line (also called the Neutral axis) is an imaginary profile that can be drawn through a cross-section of the workpiece that represents the locus where no tensile or compressive stress are present but shear stresses are at their maximum. In the bend region, the material between the neutral line and the inside radius will be under compression during the bend while the material between the neutral line and the outside radius will be under tension during the bend. Its location in the material is a function of the forces used to form the part and the material yield and tensile strengths. This theoretical definition also coincides with the geometric definition of the plane representing the unbent flat pattern shape within the cross-section of the bent part. Furthermore, the bend allowance (see below) in air bending depends primarily on the width of the opening of the bottom die. [8] As a result, the bending process is more complicated than it appears to be at first sight.

Both bend deduction and bend allowance represent the difference between the neutral line or unbent flat pattern (the required length of the material prior to bending) and the formed bend. Subtracting them from the combined length of both flanges gives the flat pattern length. The question of which to use is determined by the dimensioning method used to define the flanges as shown in the two diagrams below. The flat pattern length is always shorter in length than the sum of all the flange length dimensions due to the geometric transformation. This gives rise to the common perspective that that material is stretching during bending and the bend deduction and bend allowance are the distance that each bend stretches. While a helpful way to look at it, a careful examination of the formulas and stresses involved show this to be false.

Most 3D Solid Modeling CAD software has sheet metal functions or add-ons that performs these calculations automatically. [9]

Bend allowance

The bend allowance (BA) is the length of the arc of the neutral line between the tangent points of a bend in any material. Adding the length of each flange as dimensioned by B in the diagram to the BA gives the Flat Pattern length. This bend allowance formula is used to determine the flat pattern length when a bend is dimensioned from 1) the center of the radius, 2) a tangent point of the radius (B) or 3) the outside tangent point of the radius on an acute angle bend (C). When dimensioned to the outside tangent, the material thickness and bend radius are subtracted from it to find the dimension to the tangent point of the radius before adding in the bend allowance.

The BA can be estimated using the following formula, which incorporates the empirical K-factor: [10]

Bend allowance.svg
Angle90
Pl3.142
Radius10.0
K-factor0.33
Thickness10
Bend allowance20.89

Bend deduction

Diagram showing standard dimensioning scheme when using bend deduction formulas Bend deduction.svg
Diagram showing standard dimensioning scheme when using bend deduction formulas

The bend deduction BD is defined as the difference between the sum of the flange lengths (from the edge to the apex) and the initial flat length.

The outside set back (OSSB) is the length from the tangent point of the radius to the apex of the outside of the bend. The bend deduction (BD) is twice the outside setback minus the bend allowance. BD is calculated using the following formula, where A is the angle in radians (=degrees*π/180): [11]

For bends at 90 degrees this formula can be simplified to:

K-factor

K-factor is a ratio of the location of the neutral line to the material thickness as defined by t/T where t = location of the neutral line and T = material thickness. The K-factor formula does not take the forming stresses into account but is simply a geometric calculation of the location of the neutral line after the forces are applied and is thus the roll-up of all the unknown (error) factors for a given setup. The K-factor depends on many variables including the material, the type of bending operation (coining, bottoming, air-bending, etc.) the tools, etc. and is typically between 0.3 and 0.5.

The following equation relates the K-factor to the bend allowance: [12]

The following table is a "rule of thumb". Actual results may vary remarkably.

Generic K-factorsAluminumSteel
RadiusSoft materialsMedium materialsHard materials
Air bending
0 to thickness0.330.380.40
Thickness to 3 × thickness0.400.430.45
Greater than 3 × thickness0.500.500.50
Bottoming
0 to thickness0.420.440.46
Thickness to 3 × thickness0.460.470.48
Greater than 3 × thickness0.500.500.50
Coining
0 to thickness0.380.410.44
Thickness to 3 × thickness0.440.460.47
Greater than 3 × thickness0.500.500.50

The following formula can be used in place of the table as a good approximation of the K-factor for air bending:

Advantages and disadvantages

Bending is a cost-effective near net shape process when used for low to medium quantities. Parts usually are lightweight with good mechanical properties. A disadvantage is that some process variants are sensitive to variations in material properties. For instance, differences in spring-back have a direct influence on the resulting bend angle. To mitigate this, various methods for in-process control have been developed. [13] Other approaches include combining brakeforming with incremental forming. [14]

Broadly speaking, each bend corresponds with a set-up (although sometimes, multiple bends can be formed simultaneously). The relatively large number of set-ups and the geometrical changes during bending make it difficult to address tolerances and bending errors a priori during set-up planning, although some attempts have been made [15]

See also

Related Research Articles

<span class="mw-page-title-main">Spoke</span> Part of a wheel extending radially from the hub to the rim

A spoke is one of some number of rods radiating from the center of a wheel, connecting the hub with the round traction surface.

<span class="mw-page-title-main">Beam (structure)</span> Structural element capable of withstanding loads by resisting bending

A beam is a structural element that primarily resists loads applied laterally across the beam's axis. Its mode of deflection is primarily by bending, as loads produce reaction forces at the beam's support points and internal bending moments, shear, stresses, strains, and deflections. Beams are characterized by their manner of support, profile, equilibrium conditions, length, and material.

<span class="mw-page-title-main">Pressure vessel</span> Vessel for pressurised gases or liquids

A pressure vessel is a container designed to hold gases or liquids at a pressure substantially different from the ambient pressure.

A die is a specialized machine tool used in manufacturing industries to cut and/or form material to a desired shape or profile. Stamping dies are used with a press, as opposed to drawing dies and casting dies which are not. Like molds, dies are generally customized to the item they are used to create.

<span class="mw-page-title-main">Buckling</span> Sudden change in shape of a structural component under load

In structural engineering, buckling is the sudden change in shape (deformation) of a structural component under load, such as the bowing of a column under compression or the wrinkling of a plate under shear. If a structure is subjected to a gradually increasing load, when the load reaches a critical level, a member may suddenly change shape and the structure and component is said to have buckled. Euler's critical load and Johnson's parabolic formula are used to determine the buckling stress of a column.

<span class="mw-page-title-main">Metal fabrication</span> Creation of metal structures

Metal fabrication is the creation of metal structures by cutting, bending and assembling processes. It is a value-added process involving the creation of machines, parts, and structures from various raw materials.

<span class="mw-page-title-main">Sheet metal</span> Metal formed into thin, flat pieces

Sheet metal is metal formed into thin, flat pieces, usually by an industrial process.

<span class="mw-page-title-main">Punch press</span>

A punch press is a type of machine press used to cut holes in material. It can be small and manually operated and hold one simple die set, or be very large, CNC operated, with a multi-station turret and hold a much larger and complex die set.

<span class="mw-page-title-main">Punching</span> Creating a hole by forcing a tool through the workpiece

Punching is a forming process that uses a punch press to force a tool, called a punch, through the workpiece to create a hole via shearing. Punching is applicable to a wide variety of materials that come in sheet form, including sheet metal, paper, vulcanized fibre and some forms of plastic sheet. The punch often passes through the work into a die. A scrap slug from the hole is deposited into the die in the process. Depending on the material being punched this slug may be recycled and reused or discarded.

<span class="mw-page-title-main">Progressive stamping</span> Metalworking method

Progressive Die is a metalworking method that can encompass punching, coining, bending and several other ways of modifying metal raw material, combined with an automatic feeding system.

<span class="mw-page-title-main">Stamping (metalworking)</span> Forming metal sheets with a stamping press

Stamping is the process of placing flat sheet metal in either blank or coil form into a stamping press where a tool and die surface forms the metal into a net shape. Stamping includes a variety of sheet-metal forming manufacturing processes, such as punching using a machine press or stamping press, blanking, embossing, bending, flanging, and coining. This could be a single stage operation where every stroke of the press produces the desired form on the sheet metal part, or could occur through a series of stages.

<span class="mw-page-title-main">Deep drawing</span> Metalworking process

Deep drawing is a sheet metal forming process in which a sheet metal blank is radially drawn into a forming die by the mechanical action of a punch. It is thus a shape transformation process with material retention. The process is considered "deep" drawing when the depth of the drawn part exceeds its diameter. This is achieved by redrawing the part through a series of dies.

<span class="mw-page-title-main">Press brake</span>

A press brake is a machine used for bending sheet metal and metal plate, most commonly sheet metal. It forms predetermined bends by clamping the workpiece between a matching top tool and bottom die.

<span class="mw-page-title-main">Blanking and piercing</span> Shearing processes

Blanking and piercing are shearing processes in which a punch and die are used to produce parts from coil or sheet stock. Blanking produces the outside features of the component, while piercing produces internal holes or shapes. The web is created after multiple components have been produced and is considered scrap material. The "slugs" produced by piercing internal features are also considered scrap. The terms "piercing" and "punching" can be used interchangeably.

<span class="mw-page-title-main">Tube bending</span>

Tube bending is any metal forming processes used to permanently form pipes or tubing. Tube bending may be form-bound or use freeform-bending procedures, and it may use heat supported or cold forming procedures.

Process duct work conveys large volumes of hot, dusty air from processing equipment to mills, baghouses to other process equipment. Process duct work may be round or rectangular. Although round duct work costs more to fabricate than rectangular duct work, it requires fewer stiffeners and is favored in many applications over rectangular ductwork.

Formability is the ability of a given metal workpiece to undergo plastic deformation without being damaged. The plastic deformation capacity of metallic materials, however, is limited to a certain extent, at which point, the material could experience tearing or fracture (breakage).

<span class="mw-page-title-main">Roll forming</span> Continuous bending of a long strip of sheet metal into a desired cross-section

Roll forming, also spelled roll-forming or rollforming, is a type of rolling involving the continuous bending of a long strip of sheet metal into a desired cross-section. The strip passes through sets of rolls mounted on consecutive stands, each set performing only an incremental part of the bend, until the desired cross-section (profile) is obtained. Roll forming is ideal for producing constant-profile parts with long lengths and in large quantities.

Press tools are commonly used in hydraulic, pneumatic, and mechanical presses to produce the sheet metal components in large volumes. Generally press tools are categorized by the types of operation performed using the tool, such as blanking, piercing, bending, forming, forging, trimming etc. The press tool will also be specified as a blanking tool, piercing tool, bending tool etc.

Rule based DFM analysis for deep drawing. Deep drawing is a widely used cold sheet metal forming process to draw the sheet metal in forming dye of desirable cross-section using mechanical force of the punch. DFM refers to design for manufacturability. DFA refers to design for assembly. DFMA stands for design for manufacture and assembly. It is a practice for designing the engineering components keeping manufacturing and assembly aspects in mind. DFMA tries to tackle the problems that may come during the manufacturing and assembly at the design stage itself. Changes in the parts design to remove these problems while keeping the functionality of the parts intact. This is done to reduce the cost of iterations thus making the manufacturing of components more efficient and economical.

References

  1. 1 2 3 Manufacturing Processes Reference Guide, Industrial Press Inc., 1994.
  2. 1 2 3 4 5 6 7 8 9 F., M. (August 2008), "Press Brake Bending: Methods and Challenges" (PDF), Metalforming: 38–43, archived from the original (PDF) on 2011-07-14.
  3. De Vin, L.J., Streppel, A.H., Singh, U.P. & Kals, H.J.J. A process model for air bending. Journal of Materials Processing Technology, Volume 57, Issues 1–2, 1 February 1996, Pages 48-54 https://doi.org/10.1016/0924-0136(95)02043-8
  4. Tool and Manufacturing Engineers Handbook, Volume 2, Forming, 4th Edition, Society of Manufacturing Engineers, 1984
  5. 3-81. DRAW FORMING Archived August 20, 2010, at the Wayback Machine
  6. "Press Brake Training die Bending | Tooling U-SME".
  7. "Archived copy" (PDF). Archived from the original (PDF) on 2010-03-31. Retrieved 2010-02-24.{{cite web}}: CS1 maint: archived copy as title (link)
  8. De Vin, L.J., Expecting the unexpected, a must for accurate brakeforming, Journal of Materials Processing Technology, Volume 117, Issues 1–2, 2 November 2001, Pages 244-248. https://doi.org/10.1016/S0924-0136(01)01140-2
  9. Iwamoto, Lisa (2 July 2013), Digital Fabrications: Architectural and Material Techniques, Princeton Architectural Press, ISBN   9781616891787
  10. How to Calculate Bend Allowance for Your Press Brake, archived from the original on 2010-01-10, retrieved 2010-02-24.
  11. Sheet metal bend deduction, archived from the original on 2009-05-01, retrieved 2010-02-24.
  12. Diegel, Olaf (July 2002), BendWorks (PDF), archived from the original (PDF) on 2010-03-31, retrieved 2010-02-24.
  13. Lutters, D., Streppel, A. H., Kroeze, B. & Kals, H. J. J., Adaptive press brake control in air bending, Proc. of the Shemet97 Conference, Belfast, pp. 471–480, 1997.
  14. J. Magee & L. J. De Vin, Process planning for laser-assisted forming. Journal of Materials Processing Technology. Volume 120, Issues 1–3, 15 January 2002, Pages 322–326.
  15. L. J. De Vin & A. H. Streppel, Tolerance Reasoning and Set-Up Planning for Brakeforming, Int. J. Adv. Manuf. Technol., 1998, Vol. 14, 336–342.

Bibliography