Brake-specific fuel consumption

Last updated March 30, 2024

Brake-specific fuel consumption (BSFC) is a measure of the fuel efficiency of any prime mover that burns fuel and produces rotational, or shaft power. It is typically used for comparing the efficiency of internal combustion engines with a shaft output.

Calculation

The brake-specific fuel consumption is given by,

{\text{BSFC}}={\frac {r}{P}}

where:

$r$ is the fuel consumption rate in grams per second (g/s)

$P$ is the power produced in watts where

P=\tau \omega

(W)

\omega

is the engine speed in radians per second (rad/s)

\tau

is the engine torque in newton metres (N⋅m)

The above values of r, $\omega$ , and $\tau$ may be readily measured by instrumentation with an engine mounted in a test stand and a load applied to the running engine. The resulting units of BSFC are grams per joule (g/J)

Commonly BSFC is expressed in units of grams per kilowatt-hour (g/(kW⋅h)). The conversion factor is as follows:

BSFC [g/(kW⋅h)] = BSFC [g/J] × (3.6 × 10⁶)

The conversion between metric and imperial units is:

BSFC [g/(kW⋅h)] = BSFC [lb/(hp⋅h)] × 608.277

BSFC [lb/(hp⋅h)] = BSFC [g/(kW⋅h)] × 0.001644

Relation to efficiency

To calculate the actual efficiency of an engine requires the energy density of the fuel being used.

Different fuels have different energy densities defined by the fuel's heating value. The lower heating value (LHV) is used for internal-combustion-engine-efficiency calculations because the heat at temperatures below 150 °C (300 °F) cannot be put to use.

Some examples of lower heating values for vehicle fuels are:

Certification gasoline = 18,640 BTU/lb (0.01204 kW⋅h/g)

Regular gasoline = 18,917 BTU/lb (0.0122222 kW⋅h/g)

Diesel fuel = 18,500 BTU/lb (0.0119531 kW⋅h/g)

Thus a diesel engine's efficiency = 1/(BSFC × 0.0119531) and a gasoline engine's efficiency = 1/(BSFC × 0.0122225)

Operating values and as a cycle average statistic

Any engine will have different BSFC values at different speeds and loads. For example, a reciprocating engine achieves maximum efficiency when the intake air is unthrottled and the engine is running near its peak torque. The efficiency often reported for a particular engine, however, is not its maximum efficiency but a fuel economy cycle statistical average. For example, the cycle average value of BSFC for a gasoline engine is 322 g/(kW⋅h), translating to an efficiency of 25% (1/(322 × 0.0122225) = 0.2540). Actual efficiency can be lower or higher than the engine’s average due to varying operating conditions. In the case of a production gasoline engine, the most efficient BSFC is approximately 225 g/(kW⋅h), which is equivalent to a thermodynamic efficiency of 36%.

An iso-BSFC map (fuel island plot) of a diesel engine is shown. The sweet spot at 206 BSFC has 40.6% efficiency. The x-axis is rpm; y-axis is BMEP in bar (bmep is proportional to torque)

Engine design and class

BSFC numbers change a lot for different engine designs, and compression ratio and power rating. Engines of different classes like diesels and gasoline engines will have very different BSFC numbers, ranging from less than 200 g/(kW⋅h) (diesel at low speed and high torque) to more than 1,000 g/(kW⋅h) (turboprop at low power level).

Examples for shaft engines

The following table takes values as an example for the specific fuel consumption of several types of engines. For specific engines values can and often do differ from the table values shown below. Energy efficiency is based on a lower heating value of 42.7 MJ/kg (84.3 g/(kW⋅h)) for diesel fuel and jet fuel, 43.9 MJ/kg (82 g/(kW⋅h)) for gasoline.


kW	HP	Year	Engine	Type	Application	lb/(hp⋅h)	g/(kW⋅h)	Efficiency
48	64	1989	Rotax 582	gasoline, 2-stroke	Aviation, Ultralight, Eurofly Fire Fox	0.699	425^[1]	19.3%
321	431	1987	PW206B/B2	turboshaft	Helicopter, EC135	0.553	336^[2]	24.4%
427	572	1987	PW207D	turboshaft	Helicopter, Bell 427	0.537	327^[2]	25.1%
500	670	1981	Arrius 2B1/2B1A-1	turboshaft	Helicopter, EC135	0.526	320^[2]	25.6%
13.1	17.8	1897	Motor 250/400 ^[3]	Diesel, four-stroke	Stationary industrial Diesel engine	0.533	324	26.2%
820	1,100	1960	PT6C-67C	turboshaft	Helicopter, AW139	0.490	298^[2]	27.5%
515	691	1991	Mazda R26B^[4]	Wankel, four-rotor	Race car, Mazda 787B	0.470	286	28.7%
958	1,285	1989	MTR390	turboshaft	Helicopter, Tiger	0.460	280^[2]	29.3%
84.5	113.3	1996	Rotax 914	gasoline, turbo	Aviation, Light-sport aircraft, WT9 Dynamic	0.454	276^[5]	29.7%
88	118	1942	Lycoming O-235-L	gasoline	Aviation, General aviation, Cessna 152	0.452	275^[6]	29.8%
456	612	1988	Honda RA168E	gasoline, turbo	Race car, McLaren MP4/4	0.447	272^[7]	31.6%
1,770	2,380	1973	GE T700	turboshaft	Helicopter, AH-1/UH-60/AH-64	0.433	263^[8]	31.1%
3,781	5,071	1995	PW150	turboprop	Airliner, Dash 8-400	0.433	263^[2]	31.1%
1,799	2,412	1984	RTM322-01/9	turboshaft	Helicopter, NH90	0.420	255^[2]	32.1%
63	84	1991	GM Saturn I4 engine	gasoline	Cars, Saturn S-Series	0.411	250^[9]	32.8%
150	200	2011	Ford EcoBoost	gasoline, turbo	Cars, Ford	0.403	245^[10]	33.5%
300	400	1961	Lycoming IO-720	gasoline	Aviation, General aviation, PAC Fletcher	0.4	243^[11]	34.2%
5,600	7,500	1989	GE T408	turboshaft	Helicopter, CH-53K	0.4	240^[8]	33.7%
7,000	9,400	1986	Rolls-Royce MT7	gas turbine	Hovercraft, SSC	0.3998	243.2^[12]	34.7%
2,000	2,700	1945	Wright R-3350 Duplex-Cyclone	gasoline, turbo-compound	Aviation, Commercial aviation; B-29, Constellation, DC-7	0.380	231^[13]	35.5%
57	76	2003	Toyota 1NZ-FXE	gasoline	Car, Toyota Prius	0.370	225^[14]	36.4%
8,251	11,065	2005	Europrop TP400	turboprop	Airbus A400M	0.350	213^[15]	39.6%
550	740	1931	Junkers Jumo 204	diesel two-stroke, turbo	Aviation, Commercial aviation, Junkers Ju 86	0.347	211^[16]	40%
36,000	48,000	2002	Rolls-Royce Marine Trent	turboshaft	Marine propulsion	0.340	207^[17]	40.7%
2,340	3,140	1949	Napier Nomad	Diesel-compound	Concept Aircraft engine	0.340	207^[18]	40.7%
165	221	2000	Volkswagen 3.3 V8 TDI	Diesel	Car, Audi A8	0.337	205^[19]	41.1%
2,013	2,699	1940	Deutz DZ 710	Diesel two-stroke	Concept Aircraft engine	0.330	201^[20]	41.9%
42,428	56,897	1993	GE LM6000	turboshaft	Marine propulsion, Electricity generation	0.329	200.1^[21]	42.1%
130	170	2007	BMW N47 2L	Diesel	Cars, BMW	0.326	198^[22]	42.6%
88	118	1990	Audi 2.5L TDI	Diesel	Car, Audi 100	0.326	198^[23]	42.6%
66	89	1992	VAG 1.9TDI 66kw	Diesel 4-stroke	Car, Audi 80, VW Golf/Passat	0.324	197^[24]	42.8%
368	493	2017	MAN D2676LF51	Diesel 4-stroke	Truck/Bus	0.314	191^[25]	44.1%
620	830		Scania AB DC16 078A	Diesel 4-stroke	Electricity generation	0.312	190^[26]	44.4%
1,200	1,600	early 1990s	Wärtsilä 6L20	Diesel 4-stroke	Marine propulsion	0.311	189.4^[27]	44.5%
375	503	2019	MAN D2676LF78	Diesel 4-stroke	Truck/Bus	0.302	184^[28]	45.8%
3,600	4,800		MAN Diesel 6L32/44CR	Diesel 4-stroke	Marine propulsion, Electricity generation	0.283	172^[29]	49%
4,200	5,600	2015	Wärtsilä W31	Diesel 4-stroke	Marine propulsion, Electricity generation	0.271	165^[30]	51.1%
34,320	46,020	1998	Wärtsilä-Sulzer RTA96-C	Diesel 2-stroke	Marine propulsion, Electricity generation	0.263	160^[31]	52.7%
27,060	36,290		MAN Diesel S80ME-C9.4-TII	Diesel 2-stroke	Marine propulsion, Electricity generation	0.254	154.5^[32]	54.6%
34,350	46,060		MAN Diesel G95ME-C9	Diesel 2-stroke	Marine propulsion	0.254	154.5^[33]	54.6%
605,000	811,000	2016	General Electric 9HA	Combined cycle gas turbine	Electricity generation	0.223	135.5 (eq.)	62.2%^[34]
640,000	860,000	2021	General Electric 7HA.3	Combined cycle gas turbine	Electricity generation (proposed)	0.217	131.9 (eq.)	63.9%^[35]

Turboprop efficiency is only good at high power; SFC increases dramatically for approach at low power (30% P_max) and especially at idle (7% P_max) :

2,050 kW Pratt & Whitney Canada PW127 turboprop (1996)^[36]
Mode	Power	fuel flow	SFC	Energy efficiency
Nominal idle (7%)	192 hp (143 kW)	3.06 kg/min (405 lb/h)	1,282 g/(kW⋅h) (2.108 lb/(hp⋅h))	6.6%
Approach (30%)	825 hp (615 kW)	5.15 kg/min (681 lb/h)	502 g/(kW⋅h) (0.825 lb/(hp⋅h))	16.8%
Max cruise (78%)	2,132 hp (1,590 kW)	8.28 kg/min (1,095 lb/h)	312 g/(kW⋅h) (0.513 lb/(hp⋅h))	27%
Max climb (80%)	2,192 hp (1,635 kW)	8.38 kg/min (1,108 lb/h)	308 g/(kW⋅h) (0.506 lb/(hp⋅h))	27.4%
Max contin. (90%)	2,475 hp (1,846 kW)	9.22 kg/min (1,220 lb/h)	300 g/(kW⋅h) (0.493 lb/(hp⋅h))	28.1%
Take-off (100%)	2,750 hp (2,050 kW)	9.9 kg/min (1,310 lb/h)	290 g/(kW⋅h) (0.477 lb/(hp⋅h))	29.1%

Related Research Articles

The Diesel cycle is a combustion process of a reciprocating internal combustion engine. In it, fuel is ignited by heat generated during the compression of air in the combustion chamber, into which fuel is then injected. This is in contrast to igniting the fuel-air mixture with a spark plug as in the Otto cycle (four-stroke/petrol) engine. Diesel engines are used in aircraft, automobiles, power generation, diesel–electric locomotives, and both surface ships and submarines.

The diesel engine, named after Rudolf Diesel, is an internal combustion engine in which ignition of the fuel is caused by the elevated temperature of the air in the cylinder due to mechanical compression; thus, the diesel engine is called a compression-ignition engine. This contrasts with engines using spark plug-ignition of the air-fuel mixture, such as a petrol engine or a gas engine.

Horsepower (hp) is a unit of measurement of power, or the rate at which work is done, usually in reference to the output of engines or motors. There are many different standards and types of horsepower. Two common definitions used today are the imperial horsepower, which is about 745.7 watts, and the metric horsepower, which is approximately 735.5 watts.

<span class="mw-page-title-main">Wankel engine</span> Combustion engine using an eccentric rotary design

The Wankel engine is a type of internal combustion engine using an eccentric rotary design to convert pressure into rotating motion. The concept was proven by German engineer Felix Wankel, followed by a commercially feasible engine designed by German engineer Hanns-Dieter Paschke. The Wankel engine's rotor, which creates the turning motion, is similar in shape to a Reuleaux triangle, with the sides having less curvature. The rotor spins inside a figure-eight-like epitrochoidal housing around a fixed-toothed gearing. The midpoint of the rotor moves in a circle around the output shaft, rotating the shaft via a cam.

Fuel efficiency is a form of thermal efficiency, meaning the ratio of effort to result of a process that converts chemical potential energy contained in a carrier (fuel) into kinetic energy or work. Overall fuel efficiency may vary per device, which in turn may vary per application, and this spectrum of variance is often illustrated as a continuous energy profile. Non-transportation applications, such as industry, benefit from increased fuel efficiency, especially fossil fuel power plants or industries dealing with combustion, such as ammonia production during the Haber process.

The heating value of a substance, usually a fuel or food, is the amount of heat released during the combustion of a specified amount of it.

E85 is an abbreviation typically referring to an ethanol fuel blend of 85% ethanol fuel and 15% gasoline or other hydrocarbon by volume.

Gasoline gallon equivalent (GGE) or gasoline-equivalent gallon (GEG) is the amount of an alternative fuel it takes to equal the energy content of one liquid gallon of gasoline. GGE allows consumers to compare the energy content of competing fuels against a commonly known fuel, namely gasoline.

<span class="mw-page-title-main">Gas engine</span> Internal combustion engine powered by gaseous fuel

A gas engine is an internal combustion engine that runs on a fuel gas, such as coal gas, producer gas, biogas, landfill gas, natural gas or hydrogen. In the United Kingdom and British English-speaking countries, the term is unambiguous. In the United States, due to the widespread use of "gas" as an abbreviation for gasoline (petrol), such an engine is sometimes called by a clarifying term, such as gaseous-fueled engine or natural gas engine.

Allison Transmission is an American manufacturer of commercial duty automatic transmissions and hybrid propulsion systems. Allison products are specified by over 250 vehicle manufacturers and are used in many market sectors, including bus, refuse, fire, construction, distribution, military, and specialty applications.

In thermodynamics, the thermal efficiency is a dimensionless performance measure of a device that uses thermal energy, such as an internal combustion engine, steam turbine, steam engine, boiler, furnace, refrigerator, ACs etc.

<span class="mw-page-title-main">Aircraft diesel engine</span> Aircraft engine operating on the Diesel principle

The aircraft diesel engine or aero diesel is a diesel-powered aircraft engine. They were used in airships and tried in aircraft in the late 1920s and 1930s, but were never widely adopted until recently. Their main advantages are their excellent specific fuel consumption, the reduced flammability and somewhat higher density of their fuel, but these have been outweighed by a combination of inherent disadvantages compared to gasoline-fueled or turboprop engines. The ever-rising cost of avgas and doubts about its future availability have spurred a resurgence in aircraft diesel engine production in the early 2010s.

The fuel economy of an automobile relates to the distance traveled by a vehicle and the amount of fuel consumed. Consumption can be expressed in terms of the volume of fuel to travel a distance, or the distance traveled per unit volume of fuel consumed. Since fuel consumption of vehicles is a significant factor in air pollution, and since the importation of motor fuel can be a large part of a nation's foreign trade, many countries impose requirements for fuel economy. Different methods are used to approximate the actual performance of the vehicle. The energy in fuel is required to overcome various losses encountered while propelling the vehicle, and in providing power to vehicle systems such as ignition or air conditioning. Various strategies can be employed to reduce losses at each of the conversions between the chemical energy in the fuel and the kinetic energy of the vehicle. Driver behavior can affect fuel economy; maneuvers such as sudden acceleration and heavy braking waste energy.

In aerospace engineering, concerning aircraft, rocket and spacecraft design, overall propulsion system efficiency $is the efficiency with which the energy contained in a vehicle's fuel is converted into kinetic energy of the vehicle, to accelerate it, or to replace losses due to aerodynamic drag or gravity. Mathematically, it is represented as, where is the cycle efficiency and is the propulsive efficiency.$

The General Motors Firebird comprises a quartet of prototype cars that General Motors (GM) engineered for the 1953, 1956, and 1959 Motorama auto shows. The cars' designers, headed by Harley Earl, took Earl's inspiration from the innovations in fighter aircraft design at the time. General Motors never intended the cars for production, but rather to showcase the extremes in technology and design that the company was able to achieve.

Engine efficiency of thermal engines is the relationship between the total energy contained in the fuel, and the amount of energy used to perform useful work. There are two classifications of thermal engines-

Internal combustion and
External combustion engines.

Energy-efficient driving techniques are used by drivers who wish to reduce their fuel consumption, and thus maximize fuel efficiency. Many drivers have the potential to improve their fuel efficiency significantly. Simple things such as keeping tires properly inflated, having a vehicle well-maintained and avoiding idling can dramatically improve fuel efficiency. Careful use of acceleration and deceleration and especially limiting use of high speeds helps efficiency. The use of multiple such techniques is called "hypermiling".

Miles per gallon gasoline equivalent is a measure of the average distance traveled per unit of energy consumed. MPGe is used by the United States Environmental Protection Agency (EPA) to compare energy consumption of alternative fuel vehicles, plug-in electric vehicles and other advanced technology vehicles with the energy consumption of conventional internal combustion vehicles rated in miles per U.S. gallon.

A consumption map or efficiency map shows the brake-specific fuel consumption in g per kWh over mean effective pressure per rotational speed of an internal combustion engine.

The GMWhirlfire gas turbine engines were developed in the 1950s by the research division of General Motors Corporation and fitted to concept vehicles, including the Firebird concept cars, Turbo-Cruiser buses, and Turbo-Titan trucks through the 1960s. They are free-turbine turboshaft machines with two spools: one compressor/gasifier turboshaft and one power/output turboshaft sharing a common axis without a mechanical coupling between them. Fuel consumption of the first-generation GT-300 was high compared to piston engines, so thermal wheel regenerators were added to the second-generation GT-304, cutting consumption by approximately 1⁄2.

References

↑ "Operator Manual for 447/503/582" (PDF). Rotax. Sep 2010. Archived from the original (PDF) on 2017-07-22. Retrieved 2018-06-08.
1 2 3 4 5 6 7 "Gas Turbine Engines" (PDF). Aviation Week. January 2008.
↑ Günter Mau: Handbuch Dieselmotoren im Kraftwerks- und Schiffsbetrieb, Vieweg (Springer), Braunschweig/Wiesbaden 1984, ISBN 978-3-528-14889-8, p. 7
↑ Shimizu, Ritsuharu; Tadokoro, Tomoo; Nakanishi, Toru; Funamoto, Junichi (1992-02-01). "Mazda 4-Rotor Rotary Engine for the Le Mans 24-Hour Endurance Race". SAE Technical Paper Series. Vol. 1. SAE International. p. 4. doi:10.4271/920309. ISSN 0148-7191.
↑ "Operator Manual for 914 series" (PDF). Rotax. Apr 2010. Archived from the original (PDF) on 2017-06-11. Retrieved 2018-06-08.
↑ O-235 and O-290 Operator's Manual (PDF), Lycoming, Jan 2007, pp. 3–8 version-L
↑ Otobe, Yutaka; Goto, Osamu; Miyano, Hideyo; Kawamoto, Michio; Aoki, Akio; Ogawa, Tohru (1989-02-01), "Honda Formula One Turbo-charged V-6 1.5L Engine", SAE Technical Paper Series, vol. 1, SAE, doi:10.4271/890877
1 2 Peter deBock (September 18, 2019). GE turbines and small engines overview (PDF). ARPA-e INTEGRATE meeting. Global Research. General Electric.
↑ Michael Soroka (March 26, 2014). "Are Airplane Engines Inefficient?".
↑ "Advanced Gasoline Turbocharged Direct Injection (GTDI) Engine Development" (PDF). Ford Research and Advanced Engineering. May 13, 2011.
↑ IO-720 Operator's Manual (PDF), Lycoming, October 2006, pp. 3–8
↑ "MT7 Brochure" (PDF). Rolls-Royce. 2012. Archived from the original (PDF) on 2017-04-20. Retrieved 2018-07-09.
↑ Kimble D. McCutcheon (27 October 2014). "Wright R-3350 "Cyclone 18"" (PDF). Archived from the original (PDF) on 1 August 2016.
↑ Muta, Koichiro; Yamazaki, Makoto; Tokieda, Junji (8 March 2004). "Development of New-Generation Hybrid System THS II - Drastic Improvement of Power Performance and Fuel Economy". SAE Technical Paper Series. Vol. 1. Society of Automotive Engineers. doi:10.4271/2004-01-0064.
↑ Kaiser, Sascha; Donnerhack, Stefan; Lundbladh, Anders; Seitz, Arne (27–29 July 2015). A composite cycle engine concept with hecto-pressure ratio. AIAA/SAE/ASEE Joint Propulsion Conference (51st ed.). doi:10.2514/6.2015-4028.
↑ inter-action association, 1987
↑ "Marine Trent". Civil Engineering Handbook. 19 Mar 2015.
↑ "Napier Nomad". Flight. 30 April 1954.
↑ "The new Audi A8 3.3 TDI quattro: Top TDI for the luxury class" (Press release). Audi AG. July 10, 2000.
↑ "Jane's Fighting Aircraft of World War II". London, UK: Bracken Books. 1989.
↑ "LM6000 Marine Gas Turbine" (PDF). General Electric. 2016. Archived from the original (PDF) on 2016-11-19.
↑ "BMW 2.0d (N47)" (in French). Auto-innovations. June 2007.
↑ Stock, Dieter; Bauder, Richard (1 February 1990). "The New Audi 5-Cylinder Turbo Diesel Engine: The First Passenger Car Diesel Engine with Second Generation Direct Injection". SAE Technical Paper Series. Vol. 1. Society of Automotive Engineers. doi:10.4271/900648.
↑ "Realizing Future Trends in Diesel Engine Development" (PDF). Society of Automotive Engineers/VAG.
↑ "MAN TGX 2019" (PDF). MAN Truck & Bus.
↑ "DC16 078A" (PDF). Scania AB.
↑ "Wärtsilä 20 product guide" (PDF). Wärtsilä. 14 February 2017.
↑ "MAN TGX 2019" (PDF). MAN Truck & Bus.
↑ "Four-Stroke Propulsion Engines" (PDF). Man Diesel. 2015. Archived from the original (PDF) on 2016-04-17.
↑ "The new Wärtsilä 31 engine". Wärtsilä Technical Journal. 20 October 2015.
↑ "RTA-C Technology Review" (PDF). Wärtsilä. 2004. Archived from the original (PDF) on December 26, 2005.
↑ "MAN B&W S80ME-C9.4-TII Project Guide" (PDF). Man Diesel. May 2014. Archived from the original (PDF) on 2016-08-09. Retrieved 2016-06-15.
↑ "MAN B&W G95ME-C9.2-TII Project Guide" (PDF). Man Diesel. May 2014. p. 16.
↑ Tomas Kellner (17 Jun 2016). "Here's Why The Latest Guinness World Record Will Keep France Lit Up Long After Soccer Fans Leave" (Press release). General Electric. Archived from the original on 16 June 2017. Retrieved 14 April 2017.
↑ "GE Unveils New H-Class Gas Turbine—and Already Has a First Order". October 2, 2019.
↑ "ATR: The Optimum Choice for a Friendly Environment" (PDF). Avions de Transport Regional. June 2001. p. PW127F engine gaseous emissions. Archived from the original (PDF) on 2016-08-08.