Klein Heidelberg

Last updated
Klein Heidelberg
Country of originGermany
Introducedduring the World War II  (during the World War II )
Typebistatic hitchhiker system [1]
Other NamesKH

Klein Heidelberg (KH) [2] was a passive radar system deployed by the Germans during World War II. It used the signals broadcast by the British Chain Home system as its transmitter, and a series of six stations along the western coast of continental Europe as passive receivers. In modern terminology, the system was a bistatic radar. Because the system sent no signals of its own, the allies were unaware of its presence, and did not learn of the system until well after the D-Day invasion. [3] The system is referred to as Klein Heidelberg Parasit (Small Heidelberg Parasite) [4] in some references. [5]

Contents

History

The Chain Home stations were so large that they were easily visible from France and German forces were aware of them from before the war. Chain Home radar installation at Poling, Sussex, 1945. CH15173.jpg
The Chain Home stations were so large that they were easily visible from France and German forces were aware of them from before the war.

Chain Home's (CH) large antennas were visible from the French coast, hence the Germans were aware of their precise locations. Their fixed-direction broadcasts towards the continent meant it was easy to determine which signal was broadcast by which station. This was aided by the way the stations spread out their broadcasts in a series of time slots, known as "running rabbits", which allowed a signal pulse to be traced back to a particular station through its timing. [6]

Beginning in 1942, Dr. Wächter of Telefunken, working with radio engineers at the Reichspost, used this information to build a passive radar system using the CH broadcasts and their own receivers. [7] [8] This was not unlike the Daventry experiment setup that had first been used to demonstrate the radar concept in the UK in early 1935. In both cases, broadcasts from a distant station were used as a signal, and when an aircraft flew into the signal it reflected some of it to the receiver, creating a distinct "blip" on the display. [9]

To this basic concept, Wächter added the ability to measure the rough azimuth of the target by turning the entire antenna and looking for the maximum signal. CH's relatively long wavelength, around 6 m, demanded very large receiver antennas and fairly complex antenna systems to support this rotation. Another side-effect of the long wavelength was that the angular resolution was relatively low, and although a lobe switching system was considered, it was apparently never used in service. [10]

Several test systems were tested at Cherbourg in 1942 and 1943. The first operational KH system was built at the Nachtfalter (Moth) jamming station at Mont de Couple between Boulogne-sur-Mer and Calais, across the English Channel from Dover, which became operational near the end of 1943. [11] A second station at Oostvoorne in the Netherlands (Biber/Beaver) followed in the spring of 1944. Four more stations were completed in 1944, Vaudricourt (Skorpion/Scorpion), Ostend (Bremse/Horsefly), Cap d'Antifer (Auerhahn/Grouse) and Cherbourg (Tausendfüssler/Centipede). These were built on Wassermann radar antennas, and sometimes used the Wassermann's own signals for height-finding duties. [12]

Description

The primary antenna for KH was the huge Wasserman-S early warning radar. Wassermann Cylinder Chimney radar illustration.png
The primary antenna for KH was the huge Wasserman-S early warning radar.
Klein Heidelberg measured the difference in time between the two paths: (Rtx + Rrx) - L. Any resulting value can be measured at many locations, which collectively form an ellipse. BistaticRange.png
Klein Heidelberg measured the difference in time between the two paths: (Rtx + Rrx) - L. Any resulting value can be measured at many locations, which collectively form an ellipse.

The system used two antennas, a very large one on a rotating platform that was used to receive the signal reflected off the aircraft, and a much smaller one positioned about 60 metres (200 ft) away that received the signal directly from the CH station. [10] The signals from both antennas were sent to two CRTs taken from the Würzburg radar, which, in typical German fashion, were used as J-scopes. This means distances are measured as the angle around the face of the tube, rather than the linear distance across it. A graduated scale around the outside of the CRT was used to measure the angles of the various "blips" in mils (0 to 400). [13]

The operator would first select a single CH station by changing a timer so it picked up only the signals from that station. CH stations broadcast in time slots, one after the other, so it was easy to select a single station using a simple timer. The signal from the smaller antenna was sent to the left display. Using a hand wheel, the operator adjusted a delay circuit until the main blip of the directly received signal was at the 12 o'clock position on this display. [13] [10]

The right-hand CRT showed the signal received on the larger antenna. As the direct signal from the CH station was very powerful, it appeared on this display no matter what direction the antenna pointed. The display was set so that it showed only 120 of the 125 second time slot, that is, 2 milliseconds. The operator would then further fine-tune the timing so the direct signal was at the 12 o'clock position on this display as well. [13] [10]

When an aircraft flew in front of the larger antenna, some of the CH signal would reflect off it and into the receiver. Since the aircraft was not on the direct line between the two stations, the total distance travelled by the signal to the aircraft and then to the antenna will always be longer than the direct signal. [lower-alpha 1] This means a second blip appears on the second display, some time after the direct signal. Measuring the angle around the face of the display using the attached scale revealed the difference in the signal's time of arrival compared to that of the direct signal, as an elapsed time. [13]

For any given elapsed time difference, there is an infinite number of locations that match that delay. When plotted, these points form an ellipse with the CH station at one foci and the KH receiver at the other. [14] Today, this is known as the bistatic range. To aid plotting these locations, each set of ten numbers on the circular scale, say 100 to 110, was assigned to a pre-calculated ellipse, in this case "ellipse 10". The operators would then select that ellipse on a set of provided charts. [15]

To measure the angle to the target, the larger antenna was rotated around its vertical axis until the selected target blip was maximized, or alternately disappeared, or "nulled". The angle could then be read off a graduated scale that was mechanically linked to the antenna's rotation. The charts showed the ellipse and the location of the KH station; a line was drawn outward from the station's location at the measured angle, where it would eventually intersect the ellipse, locating the aircraft. [15]

The 2 ms time slot corresponded to a range of 300 kilometres (190 mi), [lower-alpha 2] but the system was capable of receiving signals on high-flying aircraft at even longer ranges. In these cases, the operator could use the timer controls to further delay the sweep on the second CRT so that it showed later times, adding that extra fixed delay back to the measured angle when looking up the correct ellipse on the charts. This allowed them to continue tracking as the aircraft flew over Germany. [13] [10]

Estimates vary as to the effectiveness of the system. Pritchard gives a range accuracy of 1 to 2 km with a bearing accuracy of 1 degree at 400 kilometres (250 mi) range, [16] while Price suggests 6 miles (9.7 km) at 280 miles (450 km). [14] Given the lack of lobe switching, the angle accuracy was more on the order of 10 degrees (+ or -5 degrees). [10]

Notes

  1. Even if the aircraft is on the direct line between the two stations, the altitude of the aircraft adds several kilometres to the overall distance.
  2. Light travels 300 km in 1 ms, but in this case the signal is travelling to and from the target, not one way.

Related Research Articles

<span class="mw-page-title-main">Radio navigation</span> Use of radio-frequency electromagnetic waves to determine position on the Earths surface

Radio navigation or radionavigation is the application of radio frequencies to determine a position of an object on the Earth, either the vessel or an obstruction. Like radiolocation, it is a type of radiodetermination.

<span class="mw-page-title-main">Chain Home</span> Radar defence system in Britain in World War II

Chain Home, or CH for short, was the codename for the ring of coastal early warning radar stations built by the Royal Air Force (RAF) before and during the Second World War to detect and track aircraft. Initially known as RDF, and given the official name Air Ministry Experimental Station Type 1 in 1940, the radar units were also known as Chain Home for most of their life. Chain Home was the first early warning radar network in the world and the first military radar system to reach operational status. Its effect on the war made it one of the most powerful weapons of what became known as the "Wizard War".

<span class="mw-page-title-main">Mid-Canada Line</span> Canadian radar defence line

The Mid-Canada Line (MCL), also known as the McGill Fence, was a line of radar stations running east–west across the middle of Canada, used to provide early warning of a Soviet bomber attack on North America. It was built to supplement the Pinetree Line, which was located farther south. The majority of Mid-Canada Line stations were used only briefly from the late 1950s to the mid-1960s, as the attack threat changed from bombers to ICBMs. As the MCL was closed down, the early warning role passed almost entirely to the newer and more capable DEW Line farther north.

Gee-H, sometimes written G-H or GEE-H, was a radio navigation system developed by Britain during World War II to aid RAF Bomber Command. The name refers to the system's use of the earlier Gee equipment, as well as its use of the "H principle" or "twin-range principle" of location determination. Its official name was AMES Type 100.

<span class="mw-page-title-main">High-frequency direction finding</span> Electronic equipment for finding radio sources

High-frequency direction finding, usually known by its abbreviation HF/DF or nickname huff-duff, is a type of radio direction finder (RDF) introduced in World War II. High frequency (HF) refers to a radio band that can effectively communicate over long distances; for example, between U-boats and their land-based headquarters. HF/DF was primarily used to catch enemy radios while they transmitted, although it was also used to locate friendly aircraft as a navigation aid. The basic technique remains in use as one of the fundamental disciplines of signals intelligence, although typically incorporated into a larger suite of radio systems and radars instead of being a stand-alone system.

Passive radar is a class of radar systems that detect and track objects by processing reflections from non-cooperative sources of illumination in the environment, such as commercial broadcast and communications signals. It is a specific case of bistatic radarpassive bistatic radar (PBR) – which is a broad type also including the exploitation of cooperative and non-cooperative radar transmitters.

Serrate was a World War II Allied radar detection and homing device used by night fighters to track Luftwaffe night fighters equipped with the earlier UHF-band BC and C-1 versions of the Lichtenstein radar. It allowed RAF night fighters to attack their German counterparts, disrupting their attempts to attack the RAF's bomber force.

Lobe switching is a method used on early radar sets to improve tracking accuracy. It uses two slightly separated antenna elements to send the beam slightly to either side of the midline of the antenna. The radar signal switched between the two and produced two "blips" on the display. By comparing the lengths of the blips, the operator could find which one gave the stronger return, thereby indicating which direction the antenna should be moved to point directly at the target. The concept was used only briefly, and was almost completely replaced by conical scanning systems by the end of World War II. The concept is also infrequently referred to as sequential lobing, particularly when the signal steps between several different angles rather than just two.

<span class="mw-page-title-main">Bistatic radar</span> Radio wave detection and transmission system defined by its separation

Bistatic radar is a radar system comprising a transmitter and receiver that are separated by a distance comparable to the expected target distance. Conversely, a conventional radar in which the transmitter and receiver are co-located is called a monostatic radar. A system containing multiple spatially diverse monostatic or bistatic radar components with a shared area of coverage is called multistatic radar. Many long-range air-to-air and surface-to-air missile systems use semi-active radar homing, which is a form of bistatic radar.

<span class="mw-page-title-main">Radar display</span> Electronic device

A radar display is an electronic device that presents radar data to the operator. The radar system transmits pulses or continuous waves of electromagnetic radiation, a small portion of which backscatter off targets and return to the radar system. The receiver converts all received electromagnetic radiation into a continuous electronic analog signal of varying voltage that can be converted then to a screen display.

In radar systems, the blip-to-scan ratio, or blip/scan, is the ratio of the number of times a target appears on a radar display to the number of times it theoretically could be displayed. Alternately it can be defined as the ratio of the number of scans in which an accurate return is received to the total number of scans.

<span class="mw-page-title-main">AN/FPS-23</span>

The Motorola AN/FPS-23 was a short-range early warning radar deployed on the Distant Early Warning Line. It was used as a "gap filler", looking for aircraft attempting to sneak by the DEW line by flying between the main AN/FPS-19 stations at low altitude. It could detect aircraft flying at 200 feet over land or 50 feet over water. The system was known as Fluttar during its development at the Lincoln Laboratory, and this name was widely used for the production units as well. It was also sometimes known as "Type F".

<span class="mw-page-title-main">Type 271 radar</span> British WWII naval surface search radar

The Type 271 was a surface search radar used by the Royal Navy and allies during World War II. The first widely used naval microwave-frequency system, it was equipped with an antenna small enough to allow it to be mounted on small ships like corvettes and frigates, while its improved resolution over earlier radars allowed it to pick up a surfaced U-boat at around 3 miles (4.8 km) and its periscope alone at 900 yards (820 m).

<span class="mw-page-title-main">AI Mark IV radar</span> Operational model of the worlds first air-to-air radar system

Radar, Airborne Interception, Mark IV, produced by USA as SCR-540, was the world's first operational air-to-air radar system. Early Mk. III units appeared in July 1940 on converted Bristol Blenheim light bombers, while the definitive Mk. IV reached widespread availability on the Bristol Beaufighter heavy fighter by early 1941. On the Beaufighter, the Mk. IV arguably played a role in ending the Blitz, the Luftwaffe's night bombing campaign of late 1940 and early 1941.

<span class="mw-page-title-main">GL Mk. I radar</span>

Radar, Gun Laying, Mark I, or GL Mk. I for short, was an early radar system developed by the British Army to provide range information to associated anti-aircraft artillery. There were two upgrades to the same basic system, GL/EF and GL Mk. II, both of which added the ability to accurately determine bearing and elevation.

Sugar Tree is the name of a bistatic over-the-horizon radar built by the US in the 1960s. The key idea in Sugar Tree was a reinvention of the Klein Heidelberg Nazi German passive radar system developed for use in the Second World War. Sugar Tree was a "covert hitchhiker using Soviet, surface-wave HF radio broadcast signals and a remote sky-wave receiver to detect Soviet ballistic missile launches". The key idea, in other words, is to receive radar reflections without oneself transmitting a radar signal by using instead some other signal, typically one that originates from the adversary.

<span class="mw-page-title-main">IFF Mark II</span> Aircraft identification system

IFF Mark II was the first operational identification friend or foe system. It was developed by the Royal Air Force just before the start of World War II. After a short run of prototype Mark Is, used experimentally in 1939, the Mark II began widespread deployment at the end of the Battle of Britain in late 1940. It remained in use until 1943, when it began to be replaced by the standardised IFF Mark III, which was used by all Allied aircraft until long after the war ended.

<span class="mw-page-title-main">AMES Type 82</span> Cold War-era British medium-range 3D radar

The AMES Type 82, also widely known by its rainbow codename Orange Yeoman, was an S-band 3D radar built by Marconi and used by the Royal Air Force (RAF), initially for tactical control and later for air traffic control (ATC).

<span class="mw-page-title-main">ASV Mark III radar</span>

Radar, Air-to-Surface Vessel, Mark III, or ASV Mk. III for short, was a surface search radar system used by RAF Coastal Command during World War II. It was a slightly modified version of the H2S radar used by RAF Bomber Command, with minor changes to the antenna to make it more useful for the anti-submarine role. It was Coastal Command's primary radar from the spring of 1943 until the end of the war. Several improved versions were introduced, notably the ASV Mark VI, which replaced most Mk. IIIs from 1944 and ASV Mark VII radar, which saw only limited use until the post-war era.

<span class="mw-page-title-main">AMES Type 7</span>

The AMES Type 7, also known as the Final GCI, was a ground-based radar system introduced during World War II by the Royal Air Force (RAF). The Type 7 was the first truly modern radar used by the Allies, providing a 360 degree view of the airspace around the station out to a distance of about 90 miles (140 km). It allowed fighter interceptions to be plotted directly from the radar display, a concept known as ground controlled intercept, or GCI.

References

Citations

  1. Nicholas J. Willis (2005). Bistatic Radar. SciTech Publishing. pp. 34–. ISBN   978-1-891121-45-6.
  2. Nicholas J. Willis; Hugh D. Griffiths (2007). Advances in Bistatic Radar. SciTech Publishing. pp. 19–. ISBN   978-1-891121-48-7.
  3. Pritchard (p.124), however, claims the British were aware of it and tried countermeasures unsuccessfully.
  4. David Pritchard (1989). The Radar War: Germany's Pioneering Achievement 1904-45. P. Stephens. pp. 122–. ISBN   978-1-85260-246-8.
  5. One German internet article uses another name, das "Heidelberg"-Gerät, literally the Heidelberg equipment. The article also mentions it was used to track bombers from their bases in Britain.
  6. Neale, B. T. (1985). "CH - The First Operational Radar". The GEC Journal of Research. 3 (2): 74. copy at The Radar Pages
  7. Willis & Griffiths 2007, p. 16.
  8. Galati 2015, p. 112.
  9. Gough, Jack (1993). Watching the Skies: The History of Ground Radar in the Air Defense of the United Kingdom. Her Majesty's Stationery Office. p. 3. ISBN   0117727237.
  10. 1 2 3 4 5 6 von Gregor 1945, p. 2.
  11. von Gregor 1945, p. 1.
  12. Willis & Griffiths.
  13. 1 2 3 4 5 Willis & Griffiths 2007, pp. 16–17.
  14. 1 2 Willis & Griffiths 2007, p. 17.
  15. 1 2 Bauer 2014.
  16. Pritchard 1989, p. 123.

Bibliography