MIL-STD-130

Last updated

MIL-STD-130, "Identification Marking of U.S. Military Property," is a specification that describes markings required on items sold to the Department of Defense (DoD), including the addition, in about 2005, of UII (unique item identifier) Data Matrix machine-readable information (MRI) requirements. MIL-STD-130 describes the materials allowed, minimum text size and fonts, format, syntax and rules for identifying marks on a part, where to locate this marking plus exceptions and unique situations, such as vehicle identification numbers, cell phone IDs, etc. Other non-identifying markings—such as "this end up"—are covered under MIL-STD-129.

Contents

The purpose of the Department of Defense UII Registry is to have a single location where everything owned by the department is logged with purchase date, purchase price and dates when it is sent for repairs/refurbishment or taken out of commission. CLIN (contract line items) are entered automatically into the UID database if request for payment was made using a DD250 form and sent using the government portal WAWF. If there is any deviation from that, then third-party reporting software can be used to report.

Since 2005, MIL-STD-130 is most noted for the IUID data matrix, which is a square, pixelated barcode that when scanned connects the DoD user immediately to the record in the DoD UID Database. The UII data matrix does not contain information in itself. The construction rules exist to achieve the desired goal of a truly unique number for all time. There are several label-making software programs and a handful of scanner-verifiers on the market that achieve the required syntax of a DoD UID data matrix. There are also commercial data matrix that do not meet DoD standards, and the software that makes them is far less expensive; while they "look" the same they will not pass verification (a MIL-STD-130 requirement).

When clauses DFARS 252.211-7003 (new purchases) or DFARS 252.211-7007 (government owned equipment) are in the contract, assets and personal property priced at over $5,000 each on the contract or assets in the possession of the contractors costing over $5,000 must be marked with a unique serialized identification number in compliance with MIL-STD-130 either when the government buys them or as they are serviced.

MIL-STD-130 standard requires qualifying government furnished property in possession of contractors (PIPC), and qualifying end item deliverables or legacy items to be marked with a machine-readable 2D data matrix barcode. There are several allowed methods for marking, the most common being a polyester or polyimide label marked with a thermal transfer printer. Other methods are: metal nameplate laser etched, metal plate metalphoto processed, direct part-marked by dot peen, ink jet, laser etch or chemical etch. The barcode must meet several quality specifications, pass a verification process with a grade of "B" or better, and "be as permanent as the normal life expectancy of the item and be capable of withstanding the environmental tests and cleaning procedures specified for the item to which it is affixed". [1]

Unique identifier (UID)

Unique identifier (UID) or (UII), also referred as Item Unique Identification (IUID) in the DoD terminology, marks qualifying tangible items in the form of a number, character string, or sequence of bits assigned to a separate entity or its relevant attribute that uniquely distinguish it from other entities. The construction rules depend upon the serial number being unique to that part number (construct 2) or unique to the company (construct 1). In practice, most companies construct the UID with Cage-part-serial (construct 2). The general custom (not yet a 'shall') is that new acquisitions are marked using cage code in Format 06 (17V, 1P, S), while legacy (older stuff, already owned, or purchased without the DFARS 252.211-7003 clause in the contract) is marked with DoDaac of the entity making the label, in format 06 also (7L, 1P, S). The 17V means cage code and the 7L means DoDaac in the first position.

Construct 1 is a quickie gap-filler that permits printing a string of cage-serial in sequence and carrying the strip to the location to slap them on any kind of item. When reporting these the DoD would like much additional information, anything that can be pulled off the nameplate such as description, manufacturer, dates, and other key info. However, many depots and hired hands doing this labeling are not including any info on what they're reporting so the DoD is going very cold on using Construct 1. Use Construct 1 for new sales ONLY if your plant makes only 1 item, more or less, and your software provides plenty of 'marks'--reports all the info that would exist on a well-filled out product label, including warranty info.

Processes of choosing MIL-STD-130

It is vital to use durable and permanent label solutions for UID-compliant process. The type of materials can range from aluminium, stainless steel, polyester or polyimide adhesive-backed stickers. However, the UID nameplates must meet MIL-STD-130 standards.

Revisions of MIL-STD-130

The latest revision of MIL-STD-130 (as of September 2019) is MIL-STD-130N w/Change 1 dated 16 November 2012, superseding MIL-STD-130N dated 17 December 2007.

MIL-STD-130N, which is made up of numerous other governmental and non-governmental specifications, standards, publications, and handbooks, is meant to be used as a guide in which to determine and impose the minimum needs of the government when designing a specific contract. If there any conflicts between MIL-STD-130N and one of the reference documents that are cited in MIL-STD-130N, this standard always takes precedence. For a comprehensive list of these documents, please refer to Section 2 of MIL-STD-130N.

However, there are many items that are excluded from this list, as they are either covered in other documentation, not subject to IUID (Item Unique Identification) marking, or they already carry an IUID-equivalent marking; such as the vehicle identification number (VIN) on a car or an electronic serial number (ESN) of a cell phone. Refer to Section 1.3 of MIL-STD-130N has a complete list of these items.

Marking specifications

For items that are under the control of the Department of Defense and subject for marking, there are many specifications that must be met for a proper mark. These requirements state that all marking must be applied to a metal or stiff plastic identification plate, identification band, identification tag, or identification label that is securely fastened to the item. Additionally, the marking may even be applied directly to the surface of the item itself – provided of course it can still meet the requirements described below.

When possible, the marking must be placed in a location where it will be visible and easily read during normal operation and use of the item, and in a way that ensures the mark is permanent throughout the entire life expectancy of said item. It also necessary to make sure that the marking can withstand normal environmental conditions; including cleaning and rebuilding processes.

If this is not feasible using an MRI (Machine Readable Information) marking, then a marking should be used that will last until the item is expected to be rebuilt, if applicable. In the event that there is not enough open space on an item to ensure a proper IUID, then only the most essential information should be marked. This includes the EID (Enterprise Identifier, which is used to distinguish between different organizations and activities) of the supplier or manufacturer as well as the PIN (Part or Identifying Number), LOT, or batch number of the item. And finally, in the event that there is a lack of room whatsoever in which to place a proper IUID mark on the item, the marking may be placed on the packaging; as long as the mark abides by the guidelines listed in the paragraph above.

For human-readable information, the recommended minimum size for text is 0.2 centimeters, 0.08 inches; this also translates to 5.76 points. All letters should be in a sans-serif font, such as Arial, Futura, Trebuchet, or another sans-serif font, and numbers should be in Arabic numerals. The exception to this is when Roman numerals are used to mark an object, in which case the item's specific documentation and standards should be consulted to determine which font to use. The designation of "U.S." or "US" should be used only when specified elsewhere.

Whenever possible, MRI marking is the preferred method of IUID marking of the Department of Defense – though for some equipment and items free text marking may be specified. Limited to 50 characters in compliance with ISO/IEC 15459–4, all DFARS mandated marks must meet the minimum of a Data Matrix ECC 200 symbol using ISO/IEC 15434 syntax with the semantics of ISO/IEC 15418 or ATA CSDD. For items that are not subject to DFARS mandated marking, the Data Matrix ECC 200 symbol using ISO/IEC 15434 syntax and the semantics of ISO/IEC 15418 or ATA CSDD is preferred.

Unless specified below, MH10.8.7 is the MRI marking protocol that should be used to mark all items.

MIL-STD-130 compliant 2D matrix ISOIEC154342dmatrix.png
MIL-STD-130 compliant 2D matrix

An example of a MIL-STD-130 2D matrix using ATA CSDD Text Element Identifiers (TEI) is shown here. Format 12 identifies that TEI are used. Alternatively, format 06 may be used, specifying that Data Identifiers 17V, 1P and S are used instead of MFR, PNO and SEQ. The encoded string is: "[)><RS>12<GS>MFR 12345<GS>PNO 98765<GS>SEQ 0001<RS><EOT>".

"<GS>", "<RS>", and "<EOT>" represent the non-printable ASCII characters 29, 30 and 4 (decimal) respectively. This data matrix identifies an item from manufacturer (MFR) with CAGE 12345 with part number (PNO) 98765 and serial number (SEQ) 0001.

Industry-specific protocols

Information contained within an MRI

Apart from specifications regarding how to mark an item with an MRI, there are also specifications regarding the minimum amount of information that must be contained within an MRI mark. This encoded information includes:

Non-IUID items

IUID items

In addition to the standard information contained within an MRI, duplicate items are sometimes assigned a UII (Unique Item Identifier). The UII is a numbered prefix given to items in the event of duplicate part number assignments on behalf of an enterprise so that each individual part can be easily identified.

Of course, there are exceptions to the MRI marking routine as well. COTS (Commercial Off The Shelf) items that are clearly marked with some sort of commercial identification (firm name, logo, trademark, part number, etc.) and are not subject to IUID marking may be exempt from additional marking requirements, as long as the item presents no identification difficulty. Furthermore, parts within an assembly or subassembly that are not expected to be removed, repaired, or replaced are exempt from MRI marking unless it is otherwise stated in the contract.

Legacy items sometimes need to be marked, as well. If it is determined that a legacy machine needs to be marked, the EID used to generate a UII must be of the organization ensuring uniqueness rather than any previous marks.

Marking quality

Finally, there are also specifications regarding the marking quality of an MRI.

Marking arrangements

In a case where the manufacturer is also the ODA (Original Design Activity), the marking should be arranged as follows:

When a manufacturer is the CDA (Current Design Activity) but not the ODA, the following mark should be included in addition to the one above:

Parts acquired from a manufacturer other than the design activity should have their markings arranged as follows:

When the design activity is not the original activity, markings should be as follows:

Assemblies and subassemblies that do not require identification plates should be marked as above, though the abbreviation "ASSY" should be included instead of a dash as follows:

Likewise, source control items should use the abbreviation "SOCN" in place of "ASSY" above.

The free text marking for units, groups, and sets should be arranged as follows:

Any maintenance actions that are performed on any item should be marked as follows:

Non-exhaustive list of documents

Specifications

There are certain engineering documentation terms of military products which might not go in accordance with the American Identification languages. The section 3 of the standard clearly specifies those terms and helps product designers in offering a lucid definition about the items created for military.

It is mandatory for product designers to develop their products by adhering to the criteria set by the MIL-STD-130N standard. Merely setting the definition of product in accordance with the standard is not enough. The product designers have to take care of everything to satisfy the criteria. Item identification marking 'free text' often includes more information. A good designer retains all former part marking if an existing part, or typical part marking for a new part, then assigns a rectangular spot nearby for the UID, which is an additional label or small metal plate approximately where shown that contains the data matrix plus the 3 HRI that comprise the data matrix.

The requirement for the 3 HRI to be adjacent and unambiguous to the data matrix is a MIL-STD-130 requirement. There is no requirement it match the other part marking, for instance if the item were outsourced or is off-the-shelf, in which case the entity holding the Gov. contract may assign it their own part number and/or serial other than what exists on the product, and because they are labeling it will assign it their own cage code. A good example of this is a laptop used as an equipment controller; while it has a permissible ID on it, a company may wish to stick to cage-part-serial for ease of reporting and use their internal part number to report it because that's how they keep revision control for service purposes.

The most common designations for the adjacent HRI are MFR, PNO or P/N, and SER. MIL-STD-130N narrowed up the choices significantly, so drawings from pre-2008 may now show designations no longer preferred. Some companies simply use the designations 17V, 1P and S, which are surprising easy to adjust to.

See also

Related Research Articles

<span class="mw-page-title-main">Configuration management</span> Process for maintaining consistency of a product attributes with its design

Configuration management (CM) is a systems engineering process for establishing and maintaining consistency of a product's performance, functional, and physical attributes with its requirements, design, and operational information throughout its life. The CM process is widely used by military engineering organizations to manage changes throughout the system lifecycle of complex systems, such as weapon systems, military vehicles, and information systems. Outside the military, the CM process is also used with IT service management as defined by ITIL, and with other domain models in the civil engineering and other industrial engineering segments such as roads, bridges, canals, dams, and buildings.

<span class="mw-page-title-main">Identifier</span> Name that identifies a unique entity

An identifier is a name that identifies either a unique object or a unique class of objects, where the "object" or class may be an idea, physical countable object, or physical noncountable substance. The abbreviation ID often refers to identity, identification, or an identifier. An identifier may be a word, number, letter, symbol, or any combination of those.

<span class="mw-page-title-main">IEEE-488</span> General Purpose Interface Bus (GPIB) specification

IEEE 488, also known as HP-IB and generically as GPIB, is a short-range digital communications 8-bit parallel multi-master interface bus specification developed by Hewlett-Packard. It subsequently became the subject of several standards.

<span class="mw-page-title-main">Electronic Product Code</span> Universal identifier for physical object

The Electronic Product Code (EPC) is designed as a universal identifier that provides a unique identity for every physical object anywhere in the world, for all time. The EPC structure is defined in the EPCglobal Tag Data Standard, which is a freely available standard. The canonical representation of an EPC is a URI, namely the 'pure-identity URI' representation that is intended for use when referring to a specific physical object in communications about EPCs among information systems and business application software.

<span class="mw-page-title-main">Part number</span> Identifier of a particular part design in engineering

A part number is an identifier of a particular part design or material used in a particular industry. Its purpose is to simplify reference that item. A part number unambiguously identifies a part design within a single corporation. Sometimes across several corporations. For example, when specifying a screw, it is easier to refer to "HSC0424PP" than saying "Hardware, screw, machine, 4-40, 3/4" long, pan head, Phillips". In this example, "HSC0424PP" is the part number. It may be prefixed in database fields as "PN HSC0424PP" or "P/N HSC0424PP". The "Part Number" term is often used loosely to refer to items or components, and it's equivalent to "Item Number", and overlaps with other terms like SKU.

<span class="mw-page-title-main">Data Matrix</span> Two-dimensional matrix barcode

A Data Matrix is a two-dimensional code consisting of black and white "cells" or dots arranged in either a square or rectangular pattern, also known as a matrix. The information to be encoded can be text or numeric data. Usual data size is from a few bytes up to 1556 bytes. The length of the encoded data depends on the number of cells in the matrix. Error correction codes are often used to increase reliability: even if one or more cells are damaged so it is unreadable, the message can still be read. A Data Matrix symbol can store up to 2,335 alphanumeric characters.

The international standard IEC 60446Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors was a standard published by the International Electrotechnical Commission (IEC) that defined basic safety principles for identifying electrical conductors by colours or numerals, for example in electricity distribution wiring. The standard has been withdrawn; the fourth edition was merged in 2010 into the fifth edition of IEC 60445 along with the fourth edition, IEC 60445:2006.

A United States defense standard, often called a military standard, "MIL-STD", "MIL-SPEC", or (informally) "MilSpecs", is used to help achieve standardization objectives by the U.S. Department of Defense.

In United States military contracts, the contract data requirements list is a list of authorized data requirements for a specific procurement that forms a part of the contract.

The Federal Acquisition Regulation (FAR) is the principal set of rules regarding Government procurement in the United States, and is codified at Chapter 1 of Title 48 of the Code of Federal Regulations, 48 CFR 1. It covers many of the contracts issued by the US military and NASA, as well as US civilian federal agencies.

Remote Device Management(RDM) is an addition to the DMX512 control protocol for stage lighting equipment, introduced in 2006. DMX512 was developed in the late 1980s as a standard protocol for lighting consoles to communicate with dimmers, but has since been used for more complex applications, including the control of intelligent lighting fixtures. The addition of RDM addresses many of the shortcomings of DMX512, which is unidirectional with no support for metadata.

A unique identifier (UID) is an identifier that is guaranteed to be unique among all identifiers used for those objects and for a specific purpose. The concept was formalized early in the development of computer science and information systems. In general, it was associated with an atomic data type.

Failure mode effects and criticality analysis (FMECA) is an extension of failure mode and effects analysis (FMEA).

<span class="mw-page-title-main">Sound level meter</span> Device for acoustic measurements

A sound level meter is used for acoustic measurements. It is commonly a hand-held instrument with a microphone. The best type of microphone for sound level meters is the condenser microphone, which combines precision with stability and reliability. The diaphragm of the microphone responds to changes in air pressure caused by sound waves. That is why the instrument is sometimes referred to as a sound pressure level meter (SPL). This movement of the diaphragm, i.e. the sound pressure, is converted into an electrical signal. While describing sound in terms of sound pressure, a logarithmic conversion is usually applied and the sound pressure level is stated instead, in decibels (dB), with 0 dB SPL equal to 20 micropascals.

<span class="mw-page-title-main">Direct part marking</span>

Direct part marking (DPM) is a process to permanently mark parts with product information including serial numbers, part numbers, date codes, and barcodes. This is done to allow the tracking of parts through the full life cycle.

Laser bonding is a marking technique that uses lasers to bond an additive marking substance to a substrate.

Unique Identification Marking, UID marking, Item Unique Identification or IUID, is a part of the compliance process mandated by the United States Department of Defense. It is a permanent marking method used to give equipment a unique ID. Marking is essential for all equipment with an acquisition cost of over $5,000, equipment which is mission essential, controlled inventory, or serially-controlled. UID-marking is a set of data for assets that is globally unique and unambiguous. The technology used to mark an item is 2D Data Matrix ECC 200 Symbol. UID marking can be used to ensure data integrity and data quality throughout an item's lifecycle; it also supports multi-faceted business applications.

MIL-STD-129 standard is used for maintaining uniformity while marking military equipment and supplies that are transported through ships. This standard has been approved to be used by the United States Department of Defense and all other government agencies. Items must be marked for easy identification before they are transported. The marking helps the military personnel to fill the necessary requisition, when a particular stock goes short of the balance level.

The MIL-STD-1168 is a set of standard codes used to identify munitions. It was designed to replace the previous confusing Ammunition Identification Code (AIC) system used by the United States Army Ordnance Department.

ISO/IEC 20248Automatic Identification and Data Capture Techniques – Data Structures – Digital Signature Meta Structure is an international standard specification under development by ISO/IEC JTC 1/SC 31/WG 2. This development is an extension of SANS 1368, which is the current published specification. ISO/IEC 20248 and SANS 1368 are equivalent standard specifications. SANS 1368 is a South African national standard developed by the South African Bureau of Standards.

References

  1. "MIL-STD-130, 4.3 - Permanency and Legibility" (PDF).