Morris Oxford bullnose

Last updated

Morris Oxford
1913 Morris Oxford 10HP 'Bullnose' Front.jpg
Oxford 2-seater 1913
Overview
Manufacturer Morris Motors
Production1913–1926
Body and chassis
Class Small car

The "bullnose" Morris Oxford is a series of motor car models produced by British manufacturer Morris from 1913 to 1926. It was named by W R Morris after the city in which he grew up and which his cars were to industrialise.

Contents

Oxford bullnose (1913–1916)

Oxford bullnose
two-seater
MHV Morris Oxford 1913 (filtered).jpg
Oxford 2-seater 1913
W R Morris and passenger
Overview
Manufacturer W R M Motors Limited
Production1913–1916
Assembly Oxford, Oxfordshire, England
Designer W R Morris
Body and chassis
Body style
  • open 2-seater torpedo
  • open 2-seater torpedo de luxe
  • coupé cabriolet
  • limousine
  • Commercial variant
  • no windscreen or door was fitted to:
  • sporting car
  • delivery van
Layout FR layout
Related Cowley
Powertrain
Engine W&P 1,018 cc (62.1 cu in) I4
Transmission
  • 3-speeds and reverse manual W&P
  • gearbox control lever outside body
  • multiplate clutch in oil also by W&P
  • universal joint behind gearbox
  • propellor shaft in a torque tube
  • back axle — overhead Wrigley worm
Dimensions
Wheelbase
  • 84 in (2,134 mm) standard
  • track 40 in (1,016 mm) standard
  • ( increased to 42 in (1,067 mm) ) [1]
  • 90 in (2,286 mm) de luxe
  • track 45 in (1,143 mm) de luxe [1]
Length
  • 126 in (3,200 mm) standard
  • 132 in (3,353 mm) de luxe [1]
Width
  • 47 in (1,194 mm) standard
  • 50 in (1,270 mm) de luxe [1]
Kerb weight
  • 558 kg (1,230 lb) standard
  • 635 kg (1,400 lb) de luxe [1]
Chronology
SuccessorHotchkiss engined car
Engine
White & Poppe [1]
60 X 90 X 4
Overview
Manufacturer White & Poppe Limited, Lockhurst Lane, Coventry
Designer Paul August Poppe
Production
  • 1913: 393
  • 1914: 909
  • 1915: 173
  • total: 1,475
Layout
Configuration 4 in-line
Displacement 1,017.8 cc (62 cu in)
Cylinder bore 60 mm (2.4 in)
Piston stroke 90 mm (3.5 in)
Cylinder block materialiron, cast en bloc, fixed head
pistons: cast iron
crankshaft: carbon steel
main bearings: three white metal in bronze shells
Cylinder head materialfixed, iron, cast en bloc with block, detachable valve caps
Valvetrain side valve T-head
camshafts each side crankcase
adjustable tappets
Combustion
Fuel systemcarburettor W&P No. 25
magneto: Bosch type ZF4
later cars Mea
plugs: Bosch
Fuel typepetrol
Oil system main bearings: by galleries from oil flung off the flywheel
big-ends: splash
Cooling system water
circulated by thermo-siphon
no fan
Output
Power output 16.4 bhp (12.2 kW; 16.6 PS) @2,400 rpm
(observed, not a maximum)
Tax horsepower 9
Torque output 35.7 pound force-feet (48 N⋅m) @2,400 rpm
Chronology
Successor Hotchkiss

William Morris's first car was called Oxford in recognition of its home city. It was announced in The Autocar magazine in October 1912 and production began in March 1913. [1] Because he had a limited amount of capital and was unwilling to share ownership of his business little was made in-house. Virtually all components were bought-in and assembled by Morris. It was a small car with a 1018 cc four-cylinder side-valve engine with fixed cylinder head from White & Poppe. Ignition was by a Bosch magneto. [2]

The chassis made by Rubery Owen was of pressed-steel construction and suspension was by leaf springs, semi-elliptic at the front and longer three-quarter elliptic at the rear slung above the axle. The welded single piece banjo rear axle with splined half shafts was driven by a Wrigley Worm. The front axle was of forged steel and, like the back axle assembly and the steering, was made by Wrigley. The brakes, on the rear wheels only, were the external contracting type, metal to metal, using four shoes in each drum. A White & Poppe three-forward and reverse gearbox was fitted. The Powell & Hanmer headlamps were acetylene and the side and tail lamps oil. The windscreen, by Auster Limited of Barford Street, Birmingham, like the lamps was classed as an accessory. [1]

The car got its popular name, Bullnose, from its distinctive round-topped radiator at first called the bullet nose. Most bodies, made by Raworth of Oxford, were of the two-seat open-tourer type. There was also a van version, but the chassis did not allow four-seat bodies to be fitted, as it was not strong enough and too short. [3]

Bullnose de luxe

It was first displayed at the Olympia Motor Show which opened 7 November 1913. The standard model remained in production unchanged. The new de luxe had a longer wheelbase, 90 in (2,300 mm), and track was now 45 in (1,100 mm). [1]

The range of bodies was now expanded from the simple two-seater to include even a limousine and a sporting car which, like the vans, had no windscreen or doors but was provided with a speedometer as a standard fitting. [1]

Its front axle and steering had been re-designed to reduce "bump-steer"and its radiator capacity increased. Grooved tyres were now supplied at the rear. The banjo back axle was no longer welded but built up from three pieces and its springs were now slung below it. [1]

Trial of the Morris-Oxford Light Car

In April 1914 interested readers of The Times were asked to remember the suggested solution to anxiety amongst British manufacturers brought about by the influx of cheaper American vehicles. The suggestion was to have British firms co-operate producing a certain part or parts of the complete mechanism later assembled and sold by a joint undertaking. The Morris-Oxford Light Car, it was explained to readers, was produced on a similar principle. The engine clutch and gearbox were from the works of White & Poppe, the rear axle and the rest of the transmission from Wrigley's. [4]

Of his trial The Times's correspondent reported happy results. Everything was characterised by extreme "up-to-dateness" and the vehicle lacked scarcely any amenity of the largest and most expensive car. [4]

"In general the Morris-Oxford car showed itself to be a speedy and sweet running little car with good hill-climbing powers and an unusual quality of engine flexibility. It is free from any trickiness in handling and is characterised by a general robustness of construction which is very commendable" [4]

Because of this car's significance to Britain's new motor industry the points made by The Times's correspondent are summarised below:

Cowley

The American engined Continental Cowley, with most other significant components US sourced, shown to the press in April 1915, was a 50 percent larger engined (1495 cc against 1018 cc), longer, wider and better equipped version of this Morris Oxford with the same "Bullnose" radiator. [1]

The Cowley's stronger and larger construction could carry a four-passenger body. [1]

Oxford bullnose (1919–1926)

Oxford bullnose
1919–26
1925 Morris Oxford 'bullnose' Tourer at Felbrigg Hall.jpg
1925 Four-seater tourer
on the new for 1925 long wheelbase chassis
Overview
Manufacturer W R Morris Limited
Production1919–1926
Body and chassis
Body style
  • open 2-seater
  • open 4-seater tourer
  • coupé
  • cabriolet from 1923
  • saloon from 1924
  • landaulet from 1926
  • ¾ coupé from 1926
  • saloon landaulet from 1926
Layout FR layout
Powertrain
Engine
  • side valve straight-4
  • 1,548 cc (94.5 cu in) 11.9 hp
  • - standard until September 1924
  • 1,802 cc (110.0 cu in) 13.9 hp 14/28 - optional from January 1923 to September 1924 then standard [5]
Transmission
  • 3-speeds and reverse manual
  • gearbox two plate cork-lined clutch
  • universal joint behind gearbox
  • propellor shaft in a torque tube
  • back axle: ¾ floating, spiral bevel [5]
Dimensions
Wheelbase
  • 102 in (2,591 mm) 1919-24
  • 108 in (2,743 mm) 1925-26
  • 106.5 in (2,705 mm) 1927 [5]
  • track 48 in (1,219 mm) [5]
Length
  • 150 in (3,810 mm) 2-seater 153 in (3,886 mm) 4-seater [5]
Width58 in (1,473 mm) [5]
Kerb weight
  • open 4-seater tourer
  • 1,876 lb (851 kg) 1921
  • 1,960 lb (889 kg) 1922
  • 2,044 lb (927 kg) 1923
  • 2,128 lb (965 kg) 1924
  • 2,352 lb (1,067 kg) 1925
  • 2,268 lb (1,029 kg) 1926 [5]
Chronology
Successor Morris Oxford flatnose

The 1919 Oxford (advertised as early as September 1918) was assembled from locally made components and now took on the rather more substantial aspect of 1915's Cowley. Longer and stronger than the old Oxford, enough to carry five passengers, the new Oxford retained the pre-war Bullnose radiator style in its larger version. [5]

From August 1919, the Cowley became the downmarket "no frills" variant with only a 2-seater body and lighter smaller tyres. The Oxford had a self-starter (an extra for the Cowley) and a better electrical system and the Oxford took and kept the Cowley's leather upholstery. [6]

The new car's 11.9 fiscal horsepower 1548 cc engine was made under licence in Coventry for Morris by a British branch of Hotchkiss the French ordnance company which was turning away from guns to the motor industry. The Hotchkiss engine used the Cowley's Detroit USA Continental Motors Company design. Hotchkiss prices well undercut White and Poppe who had made Oxford engines up to that time. Morris bought Hotchkiss's British factory in May 1923 and named it Morris Engines. [5]

When it was shown at the Scottish Motor Show in January 1920 it drew large crowds of enthusiasts all day. The chassis alone was shown and was genuinely admired for the way all transmission, everything revolving, was fully enclosed in what amounts to an oil bath, everything but the fan belt. [7] A few weeks later after a lengthy trial of the new car The Times' motoring reporter wrote that the car represents "a very decided advance in light car construction". The common sense of the designers is shown in many small details but "its greatest charm is in the engine's steam-like flexibility" and liveliness. In these respects it was the best engine the writer had ever encountered. [6]

MG version

The bodies were made by Carbodies Limited of Coventry. At first panelled entirely in aluminium in 1925 and 1926 aluminium was reserved for the lower part of the body and mudguards and scuttle were then steel. [5]

Engines
Hotchkiss / Morris 11.9
(CA and CB)
Morris 14/28 (CE)
Overview
Manufacturer Hotchkiss & Cie. Gosford Street Coventry until May 1923, works thereafter under the ownership of Morris Engines Limited [5]
Production
  • (for Morris Oxford)
  • 11.9 hp: 1919 to 1926
  • 14/28 hp: 1923 to 1930
Layout
Configuration straight-4 cast en bloc with upper crankcase [5]
Displacement
  • 1.548 L (94.5 cu in) [5]
  • 1.802 L (110.0 cu in) (14/28) [5]
Cylinder bore
  • 75 mm (3.0 in) (14/28) [5]
  • 69.5 mm (2.74 in) [5]
Piston stroke 102 mm (4.0 in) [5]
Cylinder block materialcast-iron
3-bearing crankshaft
pistons: cast-iron
crankshaft: steel stamping, bronze backed white metal bearings, sump cast aluminium [5]
Cylinder head materialcast-iron detachable
copper asbestos sandwich gasket [5]
Valvetrain side valve L-head, helical timing gears, camshaft in two plain bearings operating valves by mushroom head tappets, single valve springs [5]
Combustion
Fuel system
  • carburettor
  • 1919-1921 Zenith
  • 1922 S.U.
  • 1923-1926 Smith (various)
  • exhaust
  • 3-port
  • 4-port from February 1922
  • magneto: helical bevel drive
  • 1919 Thomson-Bennett G4*
  • 1920 B T-H
  • 1921-23 Lucas E4
  • 1924-26 Lucas GA4 [5]
Fuel typepetrol
Oil system
  • main bearings and camshaft
  • pressure lubricated by plunger pump from camshaft
  • big ends: splash [5]
Cooling system water thermosyphon,
fan assisted
radiator 1919 by Randle, thereafter by Osberton [5]
Output
Power output not published
  • tax rating 11.9hp [5]
  • tax rating 13.9hp (14/28) [5]
Chronology
PredecessorWhite & Poppe 60 X 90 X 4

Very high-speed engine

In July 1921 The Times reported on one of "the best makes of British light car of modern design" writing that the 11.9 hp Morris Oxford could attain a speed of around 45 miles an hour on the level. Indeed, the car ran up Arms Hill, a gradient of about 1 in 4, "without flinching". [8]

14/28

In 1923 the engine was enlarged to 13.9 fiscal horsepower, 1802 cc. [9] This became known as the 14/28 engine. In 1925 it got a longer wheelbase chassis to move it further from the Cowley, and four-wheel brakes. [9] This model of the Oxford would be the basis of the first MG, the 14/28 Super Sports.

Reviewed by The Times in March 1924 the enlarged engine was reported to be "commendably flexible" and quiet. It seemed to enjoy being made to turn over at high speed and that happened easily, certainly it had plenty of "courage". The oil filler's lid holds a dipper rod and forms a breather but there is still no filter at this point. The main strainer can only be withdrawn after removing a plug in the bottom of the sump. The clutch was good. There is no safety stop for reverse but the gear box was pronounced the chief delight on the car, it is "simple, quiet and expeditious". The accelerator is too sensitive. As before the brake handle was too far away. The car was "easy to travel in". Difficult to avoid on an 8' 6" wheelbase but passengers' coats sweep dusty or muddy wings on entry and exit. The dynamotor (starter-dynamo) sings (gently) at speed. For the price the equipment is very full. [10]

Floor L to R, the 'distant' handbrake, the 'interfering' change-speed lever and the under-wheel spark control.
Before the steering column is a smokers' companion and the dash displays a fuel gauge piped from the tank in the scuttle behind it 1925 Morris Oxford Felbrigg Hall 7342657938.jpg
Floor L to R, the 'distant' handbrake, the 'interfering' change-speed lever and the under-wheel spark control.
Before the steering column is a smokers' companion and the dash displays a fuel gauge piped from the tank in the scuttle behind it

At the next October's Olympia Motor Show the cars were shown with front wheel brakes, to a design by Rubury, as an optional extra at £10. The brake pedal now applied all four-wheel brakes, a separate hand lever controlled brakes at the rear. The list of accessories provided as standard equipment now extended to a 12 months full insurance policy. The reporter advised the driver's entrance appeared somewhat cramped. The claimed brake horsepower was 30. [11]

At the Motor Show 1925 the 14/28 power output was reported to be 34 bhp and four-wheel brakes were standard, the same car had Barker dipping headlamps and thermostatic control of its engine's cooling water. [12]

The Times tried the 14/28 again and reported to its readers in mid January 1926 that while there may now be better designs of light car the 14/28 represented great value for money and still came with insurance for its first twelve months. A petrol gauge on the dash and an "automatic screen wiper", two horns and a proper rear windscreen. There was still no filter in the oil filler. The same complaints were made as in previous reports yet the car's general behaviour on the road was considered "praiseworthy". [13]

Red Flash 1925
Brooklands racing special 1925 Morris Oxford Red Flash.jpg
Red Flash 1925
Brooklands racing special
Morris Oxford
MG 14/28 Super Sports 1925 1925 MG Morris Oxford 14-28 5853058996.jpg
Morris Oxford
MG 14/28 Super Sports 1925
Morris Oxford
MG 14/28 Super Sports 1925 Enamelled badge on an early MG car.jpg
Morris Oxford
MG 14/28 Super Sports 1925

Production numbers

Year
1913
1914
1915
1916
1917
1918
1919
1920
1921
1922
1923
1924
1925
1926
Total
Production [1]
393
907
320
697
126
198
360
1,932
3,077
6,937
20,024
32,939
54,151
32,183
154,244

Related Research Articles

<span class="mw-page-title-main">Morris Oxford</span> Motor vehicle

Morris Oxford is a series of motor car models produced by Morris of the United Kingdom, from the 1913 'bullnose' Oxford to the Farina Oxfords V and VI.

Morris Cowley was a name given to various cars produced by Morris from 1915 to 1958.

<span class="mw-page-title-main">Morris Minor (1928)</span> Motor vehicle

The Morris Minor is a small 4-seater car with an 850 cc engine manufactured by Morris Motors Limited from 1928 until 1934. The name was resurrected for another newer car for the same market in 1948.

The Rover 8 was a small single-cylinder 8 hp 1327 cc car made by the British Rover car company. It was Rover's first production car. It was remarkable for being supported by a backbone chassis rather than a conventional ladder frame. The first model was manufactured from 1904 to 1912. A Daimler-Knight sleeve valve engine option was available on the original model in 1911 and 1912.

<span class="mw-page-title-main">Rover 10</span> Motor vehicle

The Rover 10 was a small family car from the British Rover car company produced between 1927 and 1947.

<span class="mw-page-title-main">Morris Ten</span> Motor vehicle

The Morris Ten is a medium-sized car introduced for 1933 as the company's offering in the important 10 hp sector of the British market. It continued through a series of variants until October 1948 when along with Morris's Twelve and Fourteen it was replaced by the 13.5 hp Morris Oxford MO.

<span class="mw-page-title-main">Austin 10 hp</span> Motor vehicle

The Austin 10 hp is a high-quality small car produced between 1910 and 1915 by the British car manufacturer Austin Motor Company Limited at their Longbridge, Worcestershire plant near Birmingham. 1,336 cars were made, 213 with the 1125 cc engine and 1,123 with the 1615 cc engine. Like the 1087 cc Austin 7 hp produced by both Austin and Du Cros's Swift Motor Company it was not very successful when sold with the small engine.

<span class="mw-page-title-main">Bedford CA</span> Motor vehicle

The Bedford CA was a distinctive pug-nosed light commercial vehicle produced between 1952 and 1969 by Bedford in Luton, England.

<span class="mw-page-title-main">Austin 12/6</span> Motor vehicle

The Austin Light Twelve-Six is a 14 tax horsepower car with a 1496 cc engine that was introduced by Austin in January 1931. It was named by Austin Light Twelve to separate it from the well-established Austin Twelve. The general public then dubbed the original Twelve Heavy Twelve but Austin never used that name. The Light Twelve-Six remained in production until 1936.

<span class="mw-page-title-main">Hillman 14</span> Motor vehicle

The Hillman Fourteen is a medium-sized 4-cylinder car announced by Hillman's managing director Spencer Wilks, a son-in-law of William Hillman, at the end of September 1925. This new Fourteen substantially increased Hillman's market share and remained on sale into 1931. During this time it was the main product of the company.

<span class="mw-page-title-main">Rover 12</span> Name given to several medium-sized family cars from the British Rover car company

The Rover 12 was a name given to several medium-sized family cars from the British Rover car company between 1905 and 1948.

<span class="mw-page-title-main">Vauxhall 30-98</span> Motor vehicle

The Vauxhall 30–98 is a car manufactured by Vauxhall at Luton, Bedfordshire from 1913 to 1927. In its day, its best-known configuration was the Vauxhall Velox standard 4-seater with open tourer body. Vauxhall's own description was the 30–98 hp Vauxhall-Velox sporting car. The 30–98 is also known to enthusiasts by Vauxhall's chassis code E.

<span class="mw-page-title-main">Standard Flying Fourteen</span> Motor vehicle

The Standard Flying Fourteen is an automobile produced by the British Standard Motor Company from 1936 to 1940 and announced in October 1936. The other Flying Standard models had been announced twelve months earlier. A standard is a flag and the reference to flying standards is to flying flags as well as to the advertised abilities of the cars.

<span class="mw-page-title-main">Daimler Double-Six sleeve-valve V12</span> Reciprocating internal combustion engine

The Daimler Double-Six sleeve-valve V12 was a piston engine manufactured by The Daimler Company Limited of Coventry, England between 1926 and 1938. It was offered in four different sizes for their flagship cars.

<span class="mw-page-title-main">Lanchester Fourteen</span> Motor vehicle

The Lanchester Fourteen Roadrider is a six-cylinder automobile introduced by the Lanchester Motor Company in the beginning of September 1936. It was named "Roadrider" for its special suspension features, and billed as the lowest-priced six-cylinder Lanchester ever offered. This car replaced the previous 12 hp Light Six model with a larger six-cylinder engine again in the Lanchester Eleven chassis and body.

<span class="mw-page-title-main">Morris Twelve</span> Motor vehicle

Morris Twelve is a model of Morris car introduced without fanfare in the autumn of 1934 as little more than a larger engined Morris Ten Four for which just another £5 was asked. The chassis and body were of the slow-selling longer wheelbase Ten Six. The engine though awarded a tax rating of 11.98 hp had a cubic capacity of 1548cc compared with Morris's 1292cc (10 hp) Ten Four and 1378cc (12.09 hp) Ten Six.

<span class="mw-page-title-main">Morris Six (1928)</span> Motor vehicle

The Morris Six is a 2½-litre six-cylinder car with an overhead camshaft for its overhead valves first displayed at the October 1927 Motor Show at Olympia as Morris Light Six. When he bought Wolseley in February 1927 W R Morris gave Wolseley employees his reason. It was that he wanted to make good 6-cylinder cars and Wolseley could do that. He said he particularly admired their 2-litre Wolseley 16/45.

Morris Oxford is a series of motor car models produced by Morris Motors of the United Kingdom, from the 1913 bullnose Oxford to the Farina Oxfords V and VI.

<span class="mw-page-title-main">Morris Oxford Six</span> Touring car manufactured by Morris Motors Ltd.

The Morris Oxford Six is a motor car produced by Morris of the United Kingdom from 1921 until 1926, and again from 1929 until 1935. Initially produced as a straight-six engined version of the Morris Oxford bullnose, the original Oxford Six was the first car produced by Morris with a six-cylinder engine, but proved to be unreliable. The versions produced from 1929 onwards were introduced as a replacement for the Morris Oxford 16/40.

<span class="mw-page-title-main">Rover 9</span> Motor vehicle

The Rover 9 is a small car produced by Britain's Rover car company. It had a 1074 cc 9 fiscal horsepower four-cylinder engine. Manufactured from 1924 until 1927 it was first supplemented then replaced by Rover's 10-12 model.

References

  1. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 The Bullnose and Flatnose Morris, Lytton P Jarman and Robin I Barraclough, David & Charles, Newton Abbot 1976 ISBN   0 7153 6665 3
  2. Heath, B. (January 2001). The Automobile (magazine). ISSN   0955-1328.
  3. Georgano, N. (2000). Beaulieu Encyclopedia of the Automobile. HMSO. ISBN   1-57958-293-1.
  4. 1 2 3 4 The Light Car. The Times, Saturday, Apr 25, 1914; pg. 12; Issue 40507
  5. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 L P Jarman and R I Barraclough, The Bullnose and Flatnose Morris, David & Charles, Newton Abbott, UK 1976
  6. 1 2 "Light" Cars. The Times, Saturday, Feb 21, 1920; pg. 5; Issue 42340
  7. Scottish Motor Show. The Times, Monday, Jan 26, 1920; pg. 7; Issue 42317
  8. Cars Of To-Day. The Times, Friday, Jul 01, 1921; pg. 8; Issue 42761
  9. 1 2 Baldwin, N. (1994). A-Z of cars of 1920s. UK: Bay View Books. ISBN   1-870979-53-2.
  10. Cars Of To-Day. The Times, Tuesday, Mar 25, 1924; pg. 8; Issue 43609
  11. The Motor Show. The Times, Monday, Oct 20, 1924; pg. 23; Issue 43787
  12. The Times, Tuesday, Sep 01, 1925; pg. 9; Issue 44055
  13. Cars Of To-Day. The Times, Tuesday, Jan 12, 1926; pg. 7; Issue 44167

Bibliography

  • Davis, Pedr (1986). The Macquarie Dictionary of Motoring.