| A.14 | |
|---|---|
 | |
| A.14 prototype (N251) at Felixstowe. [1] | |
| Role | Experimental flying boat |
| National origin | United Kingdom |
| Manufacturer | S.E. Saunders Ltd |
| Designer | Harry Knowler |
| First flight | Late 1928 |
| Status | Prototype |
| Number built | 1 |
The Saunders A.14 was a test aircraft for Saunders' new metal hull construction method, being a Supermarine Southampton fitted with the Saunders' fuselage. The methods tested worked well enough to be used in SARO flying boat production from 1928 to 1938.
After the disappointing failure of the Valkyrie to gain orders, it was evident that Saunders' traditional wooden hulled flying boats were out of date. The Saunders A.14, [2] sometimes known as the "Metal Hull", was a one-off aircraft to test Saunders' innovative metal hull design. This hull construction was used on all the Saunders and Saunders-Roe flying boats designed up to about 1935: the A.7, Cutty Sark, Cloud, Windhover and London. To avoid the effort of designing a complete aircraft to test their new hull design Saunders were awarded a joint contract with Supermarine to fit a standard Supermarine Southampton Mk. II with a Saunders hull. Thus, exactly as the Southampton, the A.14 was a large twin engined, triple finned biplane.
Saunders were keen to make the hull simple to construct, partly to keep costs down and partly because the company's craftsman were predominantly skilled in wood, rather than metal, work. The A.14 designer, Henry Knowler introduced two innovations, [2] one structural and one hydrodynamic. Other manufacturers had stiffened their hulls with longitudinal stringers, riveted to the inside of the hull. These required a lot of riveting and also some complicated mechanical detail where they met the transverse frames. Knowler's design replaced the internal stringers with external corrugations in the hull plating which needed no riveting and avoided the stringer-frame intersection. They were spaced a few inches apart, so (on each side) there were five above the chine and four on the two step planing bottom. The hydrodynamic novelty was less subtle: most flying boats had used hulls which in cross section curved outwards from the keel rather than take a simple V-form, chiefly to reduce "dirty" upward spray. Such hull forms required beaten metal panels of double curvature, rather than just bent. To avoid this complication Knowler used a single curvature V-form hull which was narrower than the upper hull at the chines, filling the gap with horizontal sheeting. The hull was built of duralumin with Alclad plating. Internally the new hull was roomier than that of the metal hulled Southampton Mk II, being wider in the beam. The Saunders fuselage was a little shorter than Supermarine's, by about a foot (300 mm) and also lighter judging by the overall empty weights for the two aircraft (8,870 lb or 4,023 kg for the A.14, [2] 9,697 lb or 4,398 kg for the Southampton [3] ). Certainly the Southampton had the more graceful lines, the rounded fuselage rising smoothly to the tail in contrast with the A.14's slab sided, linearly graded form. The two aircraft had almost identical maximum speeds, [2] [3] confirming Knowler's estimate that the inevitable extra drag of the external corrugations would be insignificant at the low speeds of these biplane flying boats.
Crew accommodation was rather like that of the Valkyrie and the Southampton, with dual control tandem open cockpits forward of the wings, a gunner's position in the extreme nose and two staggered dorsal gunner's cockpits aft of the wings. Since the A.14's purpose was that of a hull demonstrator, the armament was probably never installed.
The A.14 first flew towards the end of 1928 but only reached the Marine Aircraft Experimental Establishment in March 1930. The new plane V-shaped bottom was "clean" at take-off with little spray. By July, after almost flying 50 hours new structure was showing signs of weakness with slight distortions visible on the bottom just forward of the main step. In October, with a total of 75 hours in the air the buckling was more evident and the planing bottom had to be reinforced locally with internal stringers. It was a weakness that affected all subsequent Saro flying boats until the London. Nonetheless, the A.14 had shown that the corrugated method worked, albeit with some weaknesses, and Saro aircraft were built that way until the last Saro London left the works in 1938, 10 years after the A.14's first flight.
Data from London 1988 p.75
General characteristics
Performance
Related development
Aircraft of comparable role, configuration, and era
The Saunders-Roe SR.45 Princess was a British flying boat aircraft developed and built by Saunders-Roe at their Cowes facility on the Isle of Wight. It has the distinction of being the largest all-metal flying boat to have ever been constructed.
The Saunders-Roe SR.A/1 was a prototype flying boat fighter aircraft designed and built by British seaplane manufacturer Saunders-Roe. It was the first jet-propelled water-based aircraft in the world.
The Saunders Roe A.27 London was a British military biplane flying boat built by the Saunders Roe company. Only 31 were built, entering service with the Royal Air Force in 1936. Although due for replacement by the outbreak of World War II, they saw some active service pending the introduction of the ultimately unsuccessful Lerwick.
The Saunders-Roe A.36 Lerwick was a British flying boat built by Saunders-Roe Limited (Saro). It was intended to be used with the Short Sunderland in Royal Air Force Coastal Command but it was a flawed design and only a small number were built. They had a poor service record and a high accident rate; of 21 aircraft, 10 were lost to accidents and one for an unknown reason.
The Supermarine Stranraer is a flying boat designed and built by the British Supermarine Aviation Works company at Woolston, Southampton. It was developed during the 1930s on behalf of its principal operator, the Royal Air Force (RAF). It was the RAF's last and fastest biplane flying boat.
The Blackburn Iris was a British three-engined biplane flying boat of the 1920s. Although only five Irises were built, it was used as a long-range maritime reconnaissance aircraft by the Royal Air Force, where it equipped a squadron for four years, being used to carry out a number of notable long-distance flights. The final version of the Iris, the Iris Mark V was developed into the aircraft that replaced it in Squadron service, the Blackburn Perth.
The Supermarine Seagull was a British amphibious, military flying boat and the last to be built by the Supermarine company. Design started during the Second World War but it did not fly until three years after the war had ended and the project was cancelled without it being adopted for service.
The Supermarine Southampton was a flying boat of the interwar period designed and produced by the British aircraft manufacturer Supermarine. It was one of the most successful flying boats of the era.
The Supermarine Scapa was a British general reconnaissance flying boat built by Supermarine that was used by the Royal Air Force between 1935 and 1939. It was developed from the Southampton and formed the basis of the later Stranraer flying boat.
The Saunders Roe A.37 Shrimp was a 1930s British two-seat four-engined experimental flying boat built by Saunders-Roe Limited ("Saro") at Cowes.
The Short R.24/31 was a British twin-engined, high-wing cantilever gull winged monoplane flying-boat designed and built by Short to Air Ministry specification R.24/31 for a "General Purpose Open Sea Patrol Flying Boat". The contract also specified the use of the experimental Rolls-Royce Goshawk engine. The Saunders-Roe London and the Supermarine Stranraer competed successfully for this contract.
The Supermarine Air Yacht was a British luxury passenger-carrying flying boat. It was designed by Supermarine's chief designer R. J. Mitchell and built in Woolston, Southampton in 1929. It was commissioned by the brewing magnate Ernest Guinness, and was the first British flying yacht built to the order of a private owner. Only one machine was built.
The Saunders-Roe Duchess also known as the model P.131 was a British design for a large jet-powered flying boat envisaged by Saunders-Roe, based in Cowes on the Isle of Wight.
The Saro A.33 was a British prototype flying boat built by Saunders-Roe Limited in response to a British Air Ministry Specification R.2/33 and in competition with the Short Sunderland.
The Saunders Kittiwake was a British amphibian flying-boat built by S. E. Saunders at East Cowes, Isle of Wight.
The Saunders A.3 Valkyrie was a large three-engined biplane flying boat with a wooden hull built to an Air Ministry specification. It was not found suitable for production and helped to confirm a preference for metal-hulled flying boats.
The Saunders Severn was a three-engined biplane flying boat intended for maritime patrol duties. It performed well but was fragile and unreliable. Only one was built.
The Hiro H2H, or "Navy Type 89 Flying boat", was a Japanese patrol flying boat of the 1930s. Designed and built by the Hiro Naval Arsenal, it was a twin-engined biplane that was operated by the Imperial Japanese Navy.
The Boeing-Canada A-213 Totem was a Canadian single-engine pusher monoplane flying boat intended for forestry and fisheries patrols as well as a light utility transport for the British Columbia coastline, where there are few flat places for runways, and waterways are plentiful. The sole example, CF-ARF, CB10 was designed and built by Boeing Aircraft of Canada. The name refers to the Totem poles used by the First Nations in British Columbia.
The Hiro H3H1 or Navy Type 90-1 Flying boat was a Japanese flying boat bomber built in 1931. It was the first large all-metal aircraft built in Japan. Only one was completed.
